Documente Academic
Documente Profesional
Documente Cultură
XC60
XC60 2009, XC60 2010
Month
391
0.067 / 0.15
2009 08
IMG-334408
Required tools:
A0000162 IMG-239664
IMG-334484
IMG-334409
IMG-334410
INTRODUCTION NOTE! Read through the whole installation instruction before starting the work. The front page gives the date of this edition and the edition it replaces The second page shows the tools needed for the installation and the contents of the installation kit The illustrations display the procedure in order of operation. The order of operation is repeated in the text section Cut out the text page in order to follow the illustrations and text at the same time.
1 Note! Work is carried out the same way on left-hand drive cars as on right-hand drive cars (Mirrored). Left-hand drive car shown. In cases where there are differences between left and right-hand drive cars, both versions are shown. Turn the ignition switch to position 0. IMG-245980 Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment. 2 Remove the tunnel console's panel on the left-hand side (Also applies to right-hand drive cars). It is secured with seven clips on the inside.
IMG-298585 3 Carefully pry loose the panel with air blower all round. The panel is secured by five clips on the sides and at the top and with four mounting springs on the lower edge.
IMG-282523 4 Pull out the panel and disconnect the connector for the hazard warning lights.
IMG-282524 5A Illustrations A and B Replacement of the panel for the air vent Poke the catches downwards using a small screwdriver.
Fold down the air nozzle and unhook it from the four mounting eyelets at the lower edge of the panel.
IMG-303983 5B
IMG-303984 6 Poke the catches on the hazard warning button in and push the button out.
IMG-303985 7 Remove and transfer the clips to the new panel, place the old one to one side.
IMG-334413 8 Install the button for the hazard warning lights in the new panel.
IMG-334414
IMG-334416 10
IMG-329155 12
IMG-293021
13
IMG-293022 14
IMG-293023 15
IMG-293024 16
IMG-329163
17
IMG-293028 18
IMG-293029 19
IMG-329164
20 Remove the rear end with cover. Disconnect the connectors for the 12 V socket and seat heating.
IMG-334421 21 Route the cable harness to the centre console in the same way on left-hand drive and right-hand drive cars
Take a piece of curtain wire and insert it in the rear edge of the tunnel console and slide it forward on the left-hand side and out where the left side panel was located. Lift up the console at the rear edge to facilitate access.
IMG-334422 22 Take the large cable harness from the kit and secure it to the end of the wire using a piece of masking tape. Pull the cable harness forward. Lift up the tunnel console at the rear edge to facilitate pulling through. Check that the cable harness is not trapped when the tunnel console is positioned.
IMG-334423 23
Connect the male connector (1) in the new cable harness to the 12 V socket. Connect the disconnected connector (2) from the 12 V socket to the female connector (2) in the new cable harness. Reconnect the green connector (3). Insert the connectors and fuse holder down as far as possible. IMG-334424 24
IMG-329164
IMG-334426
27
IMG-334427
28
IMG-334428 29
IMG-334429
30
IMG-293023 31
IMG-334431
32
IMG-334432 33 Insert the wire through the centre console on the left-hand side and out where the side panel was located.
IMG-334433 34 Tape the routed cable using a piece of masking tape and pull up.
IMG-334434 35 Take the short cable from the kit and connect to the newly routed one.
IMG-334435
36
IMG-222265
37
IMG-333776 38
IMG-333777
39
IMG-333778
IMG-222268 41 Disconnect the lighting connector and place the panel to one side.
IMG-222270
IMG-295944
IMG-295945 44 Loosen the connector from the lamp in the glovebox lighting, it may be tight.
IMG-295946
45 Remove the six screws. If necessary, disconnect the connector from the SIM card holder. Pull the glove compartment out slightly so that the clips release. Remove the glovebox. IMG-295947
46 Take the panel with cradle and aerial from the kit.
Insert the aerial over the air vent to the right and down towards the rear edge of the dashboard. Note! Leave enough cable excess so that the panel with cradle is not in the way when making connections in the centre console.
IMG-334449 47 Continue to route the aerial with cable, from the right air duct in the centre console, and then along the rear edge of the dashboard to the right. Secure using pieces of butyl tape.
IMG-333785
48 Continue to route the aerial with cable towards the air duct at the right end of the dashboard. Route it on the outside of the air duct and out through the hole in the end and position on the dashboard. Secure the cable to the outside of the air duct using butyl tape.
IMG-333786
49 Clean the surface in front of the air vent on the right-hand side of the dashboard and wipe dry.
IMG-334452 51 Steps 51-53 are mirrored for right-hand drive cars Secure the aerial approximately in position as shown.
IMG-334453 52 Route the cable under the cradle (1) for the A-pillar and back. Route the cable excess back to the rear edge of the dashboard where the cable was previously routed.
IMG-334454
53A
Illustrations A and B Secure the cable excess at the existing pieces of butyl tape according to image A and B. Also secure on the right-hand side of the air duct.
IMG-334455 53B
IMG-334456 54 Secure the green connectors at the existing cable harness using cable ties.
IMG-334457
55 Connect the connectors to the cradle and button for the hazard warning lights.
IMG-334458 56 Push the panel into place. Ensure that the cables are not in front of the air vents.
IMG-333791
58
IMG-333792 59
IMG-333793 60
Take the glovebox and connect the connector to the Sim card holder, if necessary. Insert the connector to the glovebox lighting.
IMG-296464 61
IMG-296465
62
IMG-296466 63
IMG-296467 64
IMG-286608 65
IMG-225272 66
IMG-280033
67A
Illustrations A, B and C Take the Garmin device, connect the aerial and align the guide holes in the bottom, with the corresponding lugs in the cradle. Fold it to the limit position and check that it springs up and locks in the catches on the reverse. When removing, press the receiver down until the catches release and then fold it backwards and disconnect the connector from the aerial. IMG-333800
67B
IMG-333801 67C
IMG-334328
30758143