Documente Academic
Documente Profesional
Documente Cultură
Part 1 Part 2 Part 3 Part 4 Part 5 Part 6 1.What are the different types of fits? Explain? 2. What are the factors that can affect the Factor of safety selection? 3. What is heat treatment and why is it done? 4. What are the rules that must be kept in mind while designing castings? 5. What are the points that should be kept in mind during forging design? 6. Describe briefly the different cold drawing processes. 7. What are the different theories of failure under static load, explain briefly?
What are the factors that can affect the Factor of safety selection?
The factor of safety is used in designing a machine component. Prior to selecting the correct factor of safety certain points must be taken into consideration such as: > The properties of the material used for the machine and the changes in its intrinsic properties over the time period of service. > The accuracy and authenticity of test results to the actual machine parts. > The applied load reliability. > The limit of stresses (localized). > The loss of property and life in case of failures. > The limit of initial stresses at the time period of manufacture. > The extent to which the assumptions can be simplified. The factor of safety also depends on numerous other considerations such as the material, the method of
What are the rules that must be kept in mind while designing castings?
Some of the points that must be kept in mind during the process of cast designing are as follows: > To avoid the concentration of stresses sharp corners and frequent use of fillets should be avoided. > Section thicknesses should be uniform as much as possible. For variations it must be done gradually. > Abrupt changes in the thickness should be avoided at all costs. > Simplicity is the key, the casting should be designed as simple as possible. > It is difficult to create true large spaces and henceforth large flat surfaces must be avoided. > Webs and ribs used for stiffening in castings should as minimal as possible. > Curved shapes can be used in order to improve the stress handling of the cast.
What are the points that should be kept in mind during forging design?
Some of the points that should be followed while forging design are: > A radial flow of grains or fibers must be achieved in the forged components. > The forged items such as drop and press forgings should have a parting line that should divide the forging into two equal halves. > The ribs in a forging should not be high or thin. > In order to avoid increased die wear the pockets and recesses in forgings should be minimum. > In forgings the parting line of it should lie as far as possible in a single plane. > For ease of forging and easy removal of forgings the surfaces of the metal should contain sufficient drafts.
diameter ). The dies used for the reduction process is generally made up of carbide materials. >Tube Drawing: This type of drawing is very similar to the bar drawing process and in majority of cases it is accomplished by the use of a draw bench.
What are the different theories of failure under static load, explain briefly?
The main theories of failure of a member subjected to bi-axial stress are as follows: > Maximum principal stress theory ( Rankines theory): This theory states that failure occurs at a point in member where the maximum principal or normal stress in a bi-axial system reaches the maximum strength in a simple tension test. > Maximum shear stress theory ( Guests or Trescas theory): This theory states that failure occurs when the biaxial stress reaches a value equal to the shear stress at yield point in a simple tension test. > Maximum principal strain theory ( Saint Venant theory): This theory states that failure occurs when bi-axial stress reaches the limiting value of strain. > Maximum strain energy theory ( Haighs theory): This th eory states that failure occurs when strain energy per unit volume of the stress system reaches the limiting strain energy point. > Maximum distortion energy theory ( Hencky and Von Mises theory): This theory states that failure occurs when strain energy per unit volume reaches the limiting distortion energy.
10. What do you understand by the Hooke`s Coupling what are its purposes?
The Hooke`s coupling is used to connect two shafts whose axes intersect at a small angle. The two shafts are inclined at an angle and is constant. During motion it varies as the movement is transferred from one shaft to another. One of the major areas of application of this coupling is in gear boxes where the coupling is used to drive the rear wheels of trucks and other vehicles. In such usage scenarios two couplings are used each at the two ends of the
coupling shaft. they are also used to transfer power for multiple drilling machines. The Hooke`s coupling is also known as the Universal coupling. The torque transmitted by the shafts is given by : T= (pie/16) x t x (d) cube Where T = torque, t = shear stress for the shaft material and d the diameter of the shaft.
12. Why should a chain drive be used over a belt or rope driven drive? State pro`s and con`s?
The advantages of using a chain drives are: > In a chain drive no slip occurrence takes place. > The chains take less space as compared to rope or belts as they are made of metal and offer much strength. > The chain drives can be used at both short and long ranges and they offer a high level of transmission efficiency. > Chain drives can transmit more load and power as compared to belts. > A very high speed ratio can be maintained in one step of chain drives. Some of the cons of using a chain drive are: > The cost of producing chain drives is higher as compared to that of belts. > The chain drives must be serviced and maintained at regular intervals and henceforth their cost of ownership is high comparatively.
13. What are the different types of springs and explain them briefly?
Springs can be broadly classified into the following types: > Helical Springs: These springs as their name suggests are in coil form and are in the shape of helix. The primary purpose of such springs are to handle compressive and tensile loads. They can be further classified into two types: compression helical spring and tension helical spring each having their own unique areas of application./ > Conical and volute springs: Both these spring types have specialized areas of usage where springs with adaptable rate according to the load is required. In case of conical springs they are wound so as to have a uniform pitch while on the other hand volute springs are wound in a slight manner of a parabloid. > Torsion Springs: The characteristics of such springs is that they tend to wind up by the load. They can be either helical or spiral in shape. These types of springs are used in circuit breaker mechanisms. > Leaf springs: These types of springs are comprised of metal plates of different lengths held together with the help of bolts and clamps. Commonly seen being used as suspensions for vehicles. > Disc Springs: As the name suggests such types of springs are comprised of conical discs held together by a bolt or tube. > Special Purpose Springs: These springs are all together made of different materials such as air and water.
14. During the design of a friction clutch what are the considerations that should be made?
In order to design a friction clutch the following points must be kept in mind: > The material for the contact surfaces must be carefully selected. > For high speed devices to minimize the inertia load of the clutch, low weight moving parts must be selected.
> The contact of the friction surfaces must be maintained at all the times without the application of any external forces. > Provisions for the facilitation of repairs must be there. > In order to increase safety the projecting parts of a clutch must be covered. > A provision to take up the wearing of the contact surfaces must be present. > Heat dissipaters to take away the heat from the point of contacting surfaces must be there.
15. What are the different types of brakes and explain them briefly?
Brakes can be classified on the basis of their medium used to brake, they are as follows: > Hydraulic Brakes: These brakes as their name suggest use a fluid medium to push or repel the brake pads for braking. > Electric Brakes: These brakes use electrical energy to deplete or create a braking force. Both the above types of breaks are used primarily for applications where a large amount of energy is to be transformed. > Mechanical Brakes: They can be further classified on the basis of the direction of their acting force: Radial Brakes: As their names suggests the force that acts on the brakes is of radial direction. They can further be classified into internal and external blades. Axial Brakes: In these types of brakes the braking force is acting in an axial direction as compared to radial brakes.
17. What are the basis on which the best material for Sliding Contact Bearings manufacturing?
Some of the important properties to lookout for in the material for sliding contact bearings are as follows: > Compressive Strength: In order to prevent the permanent deformation and intrusion of the bearing the material selected should be possess a high compressive strength to bear the max bearing pressure. > Fatigue Strength: the material selected for the bearing should be able to withstand loads without any surface fatigue cracks getting created. This is only possible if the material has a high level of fatigue strength. > Comfortability: The material should be able to adjust or accommodate bearing inaccuracies and deflections without much wear and heating. > Embeddability: The material should allow the embedding of small particles without effecting the material of the journal. > Bondability: The bearings may be created by bringing together ( bonding ) multiple layers of the material. Due to the above reason the bondability of the material should be sufficiently high. > Thermal conductivity and corrosion resistance: Thermal conductivity is an essential property for bearing materials as it can help in quickly dissipating the generated heat. Also the material should have a level of corrosion resistance against the lubricant.
20. Explain in an orderly manner how the force in the member of a truss be detected using the method of joint.
The steps required to calculate the force are as follows: > The reaction at the support has to be first calculated. > Once the reaction is calculated the direction of force of the member is made to make it tensile. On getting the result to be negative the direction assumed is wrong and this implies the force being compressive in nature. > A joint needs to be selected whose 2 members are not known. The lami`s theorem is used on the joint on which less than three forces are acting. > After the above process is complete the free body diagrams of the joint needs to be made. Since the system is in equilibrium the condition of Summation of V and H must result in zero. > After the above step the resolution of forces method needs to be used on the joint on which more than 4 forces are acting.
21. In order to derive the torsional formulas what are the assumptions taken?
The torsion equation is derived on the basis of following assumptions: > The shaft material is uniform, throughout the shaft. > Even after loading the shaft circular remains circular. > After the application of torques the plain section of a shaft remains plain. > Any twist that occurs in the shaft remains uniform and constant. > After the application of torque the distance between any two cross-sectional references remains constant. > The elastic limit value of a shaft is never exceeded even after the shear stress induced because of torque application. Part 1 Part 2 Part 3 Part 4 Part 5 Part 6
2) When a square or rectangular block subjected to a shear load is in equilibrium, the shear stress in one plane is always associated with a complementary shear stress in the other plane at .degrees to it. a) 90 b) 180 c) 60 d) 45 View Answer / Hide Answer
ANSWER: a) 90
3) Strain in a direction at right angles to the direction of applied force is known as a) Volumetric strain b) Shear strain c) Lateral strain d) None of these View Answer / Hide Answer
4) Youngs modulus will be ..if the radius of a wire stretched by a load is doubled. a) Become one-fourth b) Doubled c) Halved d) Unaffected View Answer / Hide Answer
ANSWER: d) Unaffected
5) The impact strength of a material is an index of its a) Toughness b) Hardness c) Tensile strength d) None of these View Answer / Hide Answer
ANSWER: a) Toughness
6) The value of Poissons ratio depends upon a) Magnitude of load b) Material of test specimen c) Cross-section and dimension of the specimen d) None of these View Answer / Hide Answer
7) Fracture will confirm to shape, when mild steel is subjected to tensile loading. a) Star b) Granular c) Cup and cone d) None of these View Answer / Hide Answer
8) The impact strength of a material is an index of its a) Toughness b) Hardness c) Resistance to corrosion d) None of these View Answer / Hide Answer
ANSWER: a) Toughness
9) If a compression test is carried on a cast iron specimen the fracture will occur a) Along an oblique plane b) Unpredictable c) Perpendicular to axis of load d) Along the axis of load View Answer / Hide Answer
10) A Notched bar test provides which of the following mechanical properties? a) Hardness b) Impact strength c) Resilience d) Endurance limit View Answer / Hide Answer
11) A bar of cross-sectional area A is subjected to a tensile force P. The normal stress on an oblique plane will be maximum when the inclination of the plane to the axis of the bar is a) 90
ANSWER: a) 90
12) At the principle planes a) All the stresses are maximum b) No stress acts c) The normal stress is maximum or minimum and the shear stress is zero d) None of these View Answer / Hide Answer
ANSWER: c) The normal stress is maximum or minimum and the shear stress is zero
13) Among the following which stresses on inclined surface can be determined by the use of Mohrs circle? a) Normal stress b) Maximum shear stress c) Tangential stress d) All of these View Answer / Hide Answer
14) Shear stresses on mutually perpendicular planes are a) Maximum b) Minimum c) Equal d) None of these View Answer / Hide Answer
ANSWER: c) Equal
15) For an element under the effect of biaxial state of normal stresses, the normal stress on a 45 plane is equal to of normal stresses a) Half the difference b) Half the sum c) Sum d) Difference View Answer / Hide Answer
16) A bar of square cross-section is subjected to an axial tensile load. A plane normal to the axis of loading will have a) Minimum normal stress and maximum shear stress b) Maximum normal stress and zero shear stress c) Minimum normal stress and zero shear stress d) Maximum normal stress and maximum shear stress View Answer / Hide Answer
17) When a material is subjected to a tensile load, then in order to avoid the shear failure of a material along a plane inclined at 45 to the direction of the tensile stress, the material should have its shear strength at least a) Equal to its tensile strength b) Equal to its compressive strength c) Equal to principal stress d) Equal to half the tensile strength View Answer / Hide Answer
18) For a cantilever beam subjected to uniformly distributed load the shearing force varies following a a) Parabolic law b) Linear law
19) In a cantilever beam carrying a load whose intensity varies uniformly from zero at the free end to w per unit length at the fixed end, the B.M changes following a a) Parabolic law b) Cubic law c) Linear law d) None of these View Answer / Hide Answer
20) For a simply supported beam carrying a uniformly distributed load of w per unit length over t he whole span, the maximum bending moment is a) wl/3 2 b) wl /3 2 c) wl /24 2 d) wl /6 View Answer / Hide Answer
ANSWER: d) wl /6
21) In a loaded beam the point of contrafexure refers to the section where the a) Bending moment changes sign b) Bending moment is maximum c) Shear force is zero d) Shear force is maximum View Answer / Hide Answer
22) The maximum compressive stress develops on ..when a rectangular beam is loaded transversely a) Bottom fibre b) Top fibre c) Neutral axis d) Middle fibre View Answer / Hide Answer
23) In the case of an I-section beam maximum shear stress is at a) Middle of the web b) The junction of top flange and web c) Either of these d) None of these View Answer / Hide Answer
24) A support is said to be non-yielding if a) It can take any amount of reaction b) It is frictionless c) The beam has zero slope at the support d) It holds the beam firmly View Answer / Hide Answer
25) Hoop stress set up in a thin cylinder subjected to internal fluid pressure is ..the longitudinal stress a) Four times b) Twice c) Thrice d) None of these
ANSWER: b) Twice
26) Spherical vessels are preferred over cylindrical shapes due to a) Easier to fabricate b) Light in weight for the same storing capacity c) Subjected to low value of hoop stress d) Greater capacity View Answer / Hide Answer
27) In a thick cylinder, the radial stress at the inner surface is a) Independent of the magnitude of the fluid pressure b) More than the magnitude of the fluid pressure c) Less than the magnitude of the fluid pressure d) Equal to the magnitude of the fluid pressure View Answer / Hide Answer
28) For a thick cylinder, the variation of circumferential stress across the thickness is a) Linear b) Uniform c) Parabolic d) None of these View Answer / Hide Answer
29) The relation between the diameter of a rivet (d) and plate thickness (t) is given by, a) d = 2t b) d = 3t c) d = 4t d) d = 6t View Answer / Hide Answer
30) The efficiency of the riveted joint is .. than that of the welded joint a) More b) Less c) Either of these d) None of these
31) In shafts with keyways the allowable stresses are usually ..of the given value. a) 75% b) 25% c) 50% d) 95% View Answer / Hide Answer
32) For the same material, length and given torque a solid shaft weights a hollow shaft a) Less than b) More than c) Equal to d) None of these View Answer / Hide Answer
33) If a torque is applied on a shaft the value of shear stress induced is a) Zero at the centre and maximum at circumference b) Zero at the circumference and maximum at centre c) Uniform throughout d) None of these View Answer / Hide Answer
34) Which among the following term is used if the slenderness ratio of a column is more than 120? a) Medium column b) Long column c) Short column d) None of these View Answer / Hide Answer
35) For a column with one end fixed and the other hinged, the ratio of equivalent length to actual length is a) 1 b) 1/2 c) 2 d) 1/2 View Answer / Hide Answer
36) What is the ratio between buckling load and safe load known as? a) Buckling factor b) Slenderness ratio
37) For ductile material . is suitable. a) Distortion energy theory b) Maximum shear stress theory c) Maximum principal strain theory d) Maximum principal stress theory View Answer / Hide Answer
38) Maximum principal stress theory was postulated by a) Mohr b) Rankine c) Tresca d) St. Venant View Answer / Hide Answer
39) In a ring under tension, where does the maximum stress occur? a) At 45 with the line of action of load. b) Along the line of action of load. c) Perpendicular to the line of action of load. d) None of these. View Answer / Hide Answer
40) The resultant deflection under symmetrical bending of a beam is a) Perpendicular to the neutral axis b) Perpendicular to the axis of symmetry c) Parallel to the neutral axis d) Parallel to the axis of symmetry View Answer / Hide Answer
41) If the load passes through the shear centre of the section of the beam, then there will be a) Only bending in the beam b) Only twisting in the beam c) Bending accompanied by twisting d) No bending in the beam View Answer / Hide Answer
a) Static compressive loads b) Static tensile loads c) Shocks d) None of these View Answer / Hide Answer
ANSWER: c) Shocks
43) For which of the following reasons are cylinders compounded? a) To increase the strength of the cylinder b) To increase the pressure bearing capacity of a single cylinder c) To make the circumferential stress distribution uniform d) All of the above View Answer / Hide Answer