Documente Academic
Documente Profesional
Documente Cultură
=
f
r
c
q
f
q
=
Typical range
0%
10%
Cohesive
Granular
CPT Results
& Soil
Classification
10
Typical
CPT Data
0 2 4 6 8 10 12 14
CPT Cone Resistance, q
c1
(MPa)
Mean
Mean-SD
Mean+SD
0 10 20 30
SPT Blow Count, N
1(60)
(Blows/300 mm)
0 20 40 60 80 100
Relative Density, D
r
(%)
From CPT
From SPT
Interpreted
Soil Profile
0
1
2
3
4
5
6
7
8
9
10
D
e
p
t
h
B
e
l
o
w
E
x
c
a
v
a
t
e
d
S
u
r
f
a
c
e
(
m
)
Interbedded
Fine Sand
and
Silty Sand
(SP-SM)
Fine Silty
Sand
(SM)
Gray Silty
Clay (CL)
Sand (SP)
Fine Sand
w/ Shells
(SP)
11
Interpreted Soil Profile
EQ Drain Test Area 1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
D
e
p
t
h
(
m
)
Sand
Silty sand/sand
Silt and Sandy
Silt
Sand to
Silty Sand
Cone Tip
Resistance, q
c
(MPa)
0 2 4 6 8 1012
Fricton Ratio, F
r
(%)
0 1 2 3 4 5 6
Relative
Density, D
r
0 0.2 0.4 0.6 0.8 1
Pore Pressure, u
(kPa)
-100 0 100 200
CPT Profile for Piezocone
CPT Versus SPT
CPT: Advantages over SPT
provides much better resolution, reliability
versatility; pore water pressure, dynamic soil
properties
CPT: Disadvantages
Does not give a sample
Will not work with soil with gravel
Need to mobilize a special rig
12
Dynamic Cone Penetration Test (DCPT)
Components:
1) Cone (dia = 50 mm)
~usually made of steel
IS: 4968 (Part I, II)
SPT
DCPT
Hollow (split spoon)
Solid (no samples)
2) Driving rods/drill
rods
~marked at every 100 mm
DCPT Procedure
Cone drill rod driving head assembly is installed
vertically on the ground and hammer is dropped from
standard height repeatedly
The blow counts are recorded for every 100 mm penetration.
A sum of three consecutive values i.e. 300 mm is noted as the
dynamic cone resistance, N
cd
at that depth.
The cone is driven up to refusal or the project specified depth.
In the end, the drill rod is withdrawn. The cone is left in the
ground if unthreaded or recovered if threaded.
No sample recovered
Fast testing less project cost / cover large area in due time
Use of bentonite slurry is optional, which is used to reduce
friction on the driving rods.
Modified cone is used in this case: diameter = 62.5 mm
13
For clays, and mainly for soft clays.
Measure torque required to quickly
shear the vane pushed into soft clay.
torque undrained shear strength c
u
Typical d = 20-100 mm.
25
Vane Shear Test (VST)
vane
undrained
bore hole
soft clay
measuring (torque)
head
vane
h~2d
d
Vane Shear Test
Test in Progress Failure surface
2
2.
. . .
1
3.
u
T
c
D H
D
H
t
=
= +
3
0.273
u
T
c
D
=
Interpretation:
Undrained shear
strength -
For H = 2.D
14
27
60 mm dia.
Flexible
membrane
Insert DMT using SPT
drilling equipment to the
desired depth and pressure
the cell
Measure pressure when the
membrane is flushed with
plate and when it enters
ground by 1.1 mm.
Decrease the pressure &
measure the pressure when
membrane is again flushed
with plate.
Determined:
Elastic Modulus
Soil Type and state
Dilatometer Test (DMT)
Pressure meter
Test (PMT)
Determined:
Elastic Young Mod, E
Shear Mod, G
Undrained shear strength, S
u
15
29
Pressure meter Test (PMT)
Measurements:
1. Fluid Pressure
2. Fluid volume change
Plate Load Test
This test is used to estimate the
Elastic Modulus and Bearing
Capacity of soils which are not
easily sampled.
Bearing Capacity Estimation: The
load is applied such that the rate of
penetration remains constant. A
load-settlement curve is produced.
Equations have been developed to
obtain undrained shear strength
from ultimate bearing capacity.
Modulus Estimation: The load is
applied to the plate in increments of one
fifth of the design load. Time-settlement
and load-settlement curves are then
produced to estimate modulus of soil
from the test results.
16
ROCK TESTING
Rock Testing
Unconfined Compression Test
Brazilian Test
Point Load Test
Direct Shear Test
Slake Durability Test
Schmidt Rebound Hardness Test
Sound Velocity Test
In-situ stress measurements in rocks
17
Core cutting &
grinding machine:
Cutting and grinding
cylindrical rock specimens
core size: EX to NX
Polishing & Lapping machine
Core drilling machine:
Rock core preparation
For regular and irregular
Samples.
core size: EX to 100mm
Specimen Preparation Equipments for
Rock Testing
Rock Core sizes:
EX = 21.46 mm
AX = 30.10 mm
BX = 42.04 mm
NX = 54.74 mm
More: 35mm, 50mm,
75mm, 100 mm
Rock Samples
Granite:
High stiffness
High strength
Very brittle
Limestone:
Medium stiffness
Medium strength
Medium brittleness
Shale:
Low stiffness
Low strength
Ductile
18
Unconfined Compression Test
This test is performed to obtain
the unconfined compressive
strength (UCS) of intact rock
cores (slenderness ratio = 2).
UCS is the maximum stress that
that rock specimen can sustain.
Rock specimen is kept in a
loading frame, and if required
heated to the desired test
temperature.
Axial load is continuously
increased on the specimen until
peak load and failure are
obtained.
Brazilian test: Tensile strength of Rock
Brazilian test is performed to obtain the
tensile strength of rock mass.
Tensile strength of rock is imp to know
for drilling, blasting of rocks, failure of
roof and floor of tunnels, chambers &
underground roadways; often weak
rocks fail in tension exhibiting splitting
mode of failure.
In this test, a disc/cylinder is subjected
to a line load, and fracture should
initiate at the centre and progress
towards periphery. If opposite, the test
is discarded as considered that it did
not fail in tension.
19
Point Load Test: compress. strength of irregular rock sp.
When regular cores could not be obtained;
only irregular pieces are available from
the rock excavation, Point load test is
performed to obtain the compressive
strength of rock mass.
The roughly chiseled spherical mass with
dia. ranging between 30-50 mm is tested
between two hard conical tips in a rigid
frame.
Direct Shear Test:
Normal stress versus Shear stress response of rock mass
It measures peak and residual direct shear strength as a function of
stress normal to the sheared plane.
It can be used for testing for both: core & lump specimens.
Shear box size: 300mm x 300mm x 100mm
20
Triaxial Shear Test:
shear strength parameters (c, |) of rock mass
Triaxial cells for testing rocks are
designed to withstand a confining
pressure 150 Kg/cm2.
Mostly triaxial tests on rock
specimens are performed under no
volume change conditions.
Stress-strain curve is obtained using
deviator stress and axial strain. The
modulus and failure deviator stress
are estimated. Shear strength
parameters (c & | ) are calculated
adopting similar methods as in soils
If the strain gauges are attached to
measure the lateral strain, poissons
ratio (v) also can be obtained.
Slake Durability Test:
Resistance of rock mass to disintegration during wetting-drying
Rock fragments of known
weight placed in rotating drum
apparatus, and rock pieces
(approx 10 pieces, each 40-60gm
weight) are circulated through
wet and dry cycles.
Re-weigh the rock fragments to
determine the slake durability
index (SDI).
Mostly, this test allows the rock
mass to get exposed up to two
cycles of wetting and drying.
21
Schmidt Test: Hardness of rock
Schmidt test is performed
to determine the rebound
hardness of rock.
The plunger of the hammer
is pressed against the
specimen and the height of
rebound of the plunger on
a scale is taken as the
measure of hardness.
Sound Velocity Test: P & S-wave velocity of rocks
It is non-destructive test and performed to determine the
velocity of elastic wave propagation through rock in the
laboratory.
slenderness ratio used for the test is usually 3. Test can be
conducted on dry, moist or saturated specimens.
A transmitter and a receiver are attached at sides of rock
specimen (a thin layer of grease is applied on the
specimens ends to have proper contact with transducers).
The energy transmission between the transducers
(transmitter and receiver) is used to determine the
velocities of P and S wave.
22
In-situ stress measurements in rocks
In-situ stress measurements in rocks:
Testing methods on Field
23
In-situ stress measurements in rocks:
Flat Jack Test
In-situ stress measurements in rocks:
Hydrofracturing Test
24
Thank You