Documente Academic
Documente Profesional
Documente Cultură
REV. HIST. A
DATE 12/12/99
APPROVALS
MELA ENG. MELA MKTG. ION CENUSE DALE MAUNU
DATE
DEC. 3RD, 99
MITSUBISHI/ADI
SIZE
A
21
TABLE OF CONTENTS
PARAGRAPH NUMBER COVER SHEET TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 OVERVIEW ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS INTERFACE PIN CONNECTION INTERFACE TIMING BLOCK DIAGRAM MECHANICAL SPECIFICATION OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITIONS LIFE TIME OF THE BACKLIGHT LAMP INSPECTION STANDARDS HANDLING PRECAUTIONS FOR TFT-LCD MODULES ITEM PAGE 1 2 3 4 4, 5 6, 7 8, 9, 10 11 12, 13, 14 15, 16 17 18 19 20, 21
SIZE
A
REV.
A SHEET 2
OF
21
1.
1.1.
OVERVIEW
Description: AA084VC03 is a 8.4-inch color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit, and backlight. By applying 6 bit digital data 640 x 480, 262K color images are displayed on the 8.4-inch diagonal screen. Input power voltage is 3.3 V (does not includes power for the backlight). Both 3.3VCMOS and 5.0V-CMOS voltage levels are acceptable for logic input voltage. Inverter for backlight is not included in this module. General specifications summary table:
1.2.
ITEM Display Area (mm) Number of Pixels Pixel Pitch (mm) Color Pixel Arrangement Display Mode Number of colors Wide Viewing Angle Technology Optimum Viewing Angle (Contrast Ratio) Brightness (cd/m ) Power Consumption (W) Module Size (mm) Module Weight (g) Backlight Unit
2
SPECIFICATION 170.9 X 128.2 (8.4-inch diagonal) 640(H) X 480(V) 0.267(H) X 0.267 (V) RGB Vertical Stripe Normally White 262K Optical Compensation Film 12 O'clock 350 5.4 199.5(W) X 149.0(H) X 11.5 (D) 420 CCFL, Two Lamps, Replaceable
1.3.
Product Disclaimer The LCD products listed in this document are not suitable for safety related applications that do not have redundant back-up system(s). In other words, these LCD products are not designed for use as a single source safety related application, and therefore, are not recommended for applications in which human life and/or environment may be affected in the event of the failure of the LCD product. More specifically, if there is no back-up system or product in place that will continue operating the system, the LCD products should not be used in such things as: (i) aircraft navigation or aerospace equipment; (ii) nuclear reactor control systems; (iii) any application where failure or inaccuracy might cause death or personal injury (e.g., life support systems); or (iv) military and submarine critical systems. The LCD products are designed for typical industrial applications such as, but not are limited to the following: computers, office equipment, industrial controllers, audio and visual equipment, test and measurement devices, communication equipment, point of sale, medical imaging and automotive and various other consumer products. If there are any questions regarding the use, ability or application of these LCD products, please contact an authorized sales representative.
SIZE
A
REV.
A SHEET 3
OF
21
2.
2.1. 2.2.
Environmental conditions: humidity 85% RH, no condensation Summary Table: ITEM SYMBOL VCC VIN Top Tstg MIN 0.3 0 0 20 MAX 5.5 7 50 60 UNIT V V C C
Power Supply Voltage for LCD Logic Input Voltage Operating Temperature Storage Temperature
3.
3.1. 3.2.
ELECTRICAL CHARACTERISTICS
Conditions: TFT-LCD module ambient temperature is 25C Summary table:
ITEM Power Supply Voltage for LCD* Power Supply Current for LCD* Permissive Input Ripple Voltage Logic Input Voltage High Low
MIN 3.0
UNIT V mA mVp-p V V
2.4 0.0
5.5 0.8
Backlight The table below shows data for one lamp only. The TFT-LCD module has two identical lamps operated independently. Operation of both lamps is required in order to meet all the parameters in the AA084VC03 specification.
SYMBOL VL IL VS
MIN
MAX
UNIT V mA V
980
SIZE
A
REV.
A SHEET 4
OF
21
3.4. 3.4.1.
t1
t2
t3
3.4.2.
VCC-dip conditions : 2.4V VCC < 3.0V and td 10ms VCC < 2.4V VCC-dip conditions should also follow the VCC turn-on conditions.
VCC
3.0V td 2.4V
3.4.3.
3.4.4.
Test condition for ICC Typical: 64 gray-bar pattern 480 line mode VCC = +3.3V Test conditions for ICC (MAX) : 1 X 1 checkerboard, black and white pattern DC input voltage = 3.3V
SIZE
A
REV.
A SHEET 5
OF
21
4.
4.1. 4.2.
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
*Note: The metal frame of the TFT-LCD module is connected to ground. SIZE
A
REV.
A SHEET 6
OF
21
4.3.
4.4.
Backlight connector type (See paragraph 6) Backlight connector (CN2 and CN3): BHR-03VS-1 (JST) Backlight mating connector: SM02(8.0)B-BHS-TB (JST) Backlight connector pin assignment table:
PIN NUMBER 1 3
SIZE
A
REV.
A SHEET 7
OF
21
5.
5.1.
INTERFACE TIMING
Timing Chart
twCH
tf CLK
tDs
twCL tDh 1 2 tDEs 3 4 First Data 5 6 7 8 Last Data 639 tDEh tDEs trDE 640 Invalid Data
DATA (R,G,B)
Invalid Data
tDEh DENA
tf DE
twDL
tHFP tHBP
trHS
VD
tf VS
twVL
tVFP
tVBP
90% 10%
SIZE
A
REV.
A SHEET 8
OF
21
5.2.
Timing Specification
SYMBOL fCLK tCLK twCL twCH trCLK tf CLK tDs tDh tDEs tDEh twDL trDE tf DE tHFP tHBP tVFP tVBP fH tH twHL trHS tf HS fV tV twVL trVS tf VS
TYP 25 40 20 20 31.5 60
DATA (R, G, B)
Set up Time Hold Time Set up Time Hold Time Low Time Rise Time
DENA
Fall Time Horizontal Front Porch Horizontal Back Porch Vertical Front Porch Vertical Back Porch Frequency Period
HD
VD
DCLK and HD should be applied continuously at the input connector of the TFT-LCD module during operation, subject to VCC turn-on conditions. Accepted only 640 data and 480 lines. Both HREV and VREV should be stable during operation.
SIZE
A
REV.
A SHEET 9
OF
21
5.3. COLOR
R
R 5 M S B R 4
D
R 3
A
R 2
T
R 1
A
R 0 L S B
G
G 5 M S B 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 G 4
D
G 3
A
G 2
T
G 1
A
G 0 L S B
B
B 5 M S B 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 B 4
D
B 3
A
B 2
T
B 1
A
B 0 L S B
BLACK RED(63) BASIC GREEN(63) BLUE(63) COLOR CYAN MAGENTA YELLOW WHITE RED(0) RED(1) RED(2) RED RED(62) RED(63) GREEN(0) GREEN(1) GREEN(2) GREEN GREEN(62) GREEN(63) BLUE(0) BLUE(1) BLUE(2) BLUE BLUE(62) BLUE(63)
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 0
0 1 0 0 0 1 1 1 0 0 1
0 1 0 0 0 1 1 1 0 1 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 1 0 1 0 1 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
0 0 0 1 1 1 0 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
0 1 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 1
0 0 0 1 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
1 1 0 0 0
0 1 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 1
0 0 0 1 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
1 1
1 1
1 1
1 1
1 1
0 1
5.3.1.
Definitions Gray scale: Color (n) n indicates gray scale level. Data: 1=High, 0=Low MITSUBISHI ELECTRIC SPECIFICATION
AA084VC03
SIZE
A
REV.
A SHEET 10
OF
21
6.
BLOCK DIAGRAM
G1 G2 Driver (gate)
TFT-LCD
BACKLIGHT
CN2
CCFL
CN3
CCFL
SIZE
A
REV.
A SHEET
OF
S1920
21
Power
G480 S1 S2
7.3.
Scanning direction This module has the capability of inverting scan direction by signaling from controller. Both horizontal and vertical scan direction can be selected independently. Note that scan direction cannot be changed during operation. The following figure show how to scan the display image data on the LCD screen. The both image data sequences are the same.
7.3.1
D(1, 1)
D(640, 1)
CN2
D(1, 480)
D(640, 480)
CN3
7.3.2
CN3
D(1, 1)
D(640, 1)
CN2
D(1, 480)
D(640, 480)
SIZE
A
REV.
A SHEET 14
OF
21
8.
8.1.
OPTICAL CHARACTERISTICS
Test conditions: Ta=25C, VCC=3.3V, IL=5mA conditions. All measurements made using BM-5A (TOPCON) or LCD-7000 (Otsuka Electronic) in a dark room, under no ambient light conditions. Summary table: ITEM SYMBOL Ratio CR L tr tf Horizontal Vertical Red Green Color CONDITION MIN TYP 300 350 20 30 60~60 40~50 0.563 0.336 0.330 0.535 0.159 0.150 0.330 0.340 12 MAX cd/m2 ms ms UNIT
8.2.
= = 0 = = 0 = = 0 = = 0
CR 10
x y x y x y x y H
= = 0
Coordinates
Blue White
Definitions Contrast Ratio CR = ON (White) Luminance / OFF (Black) Luminance Viewing Angle ( , ) - See drawing below :
Upper (+)
Left ()
Right (+)
LCD panel
Lower () SIZE
A
REV.
A SHEET 15
OF
21
8.3.3.
SIZE
A
REV.
A SHEET 16
OF
21
9.
9.1.
High Temperature and High Humidity Operation High Temperature and High Humidity Storage Lowe Temperature Storage Thermal Shock (non-operating)
9.2.
Shock and Vibration TEST ITEM Shock (non-operating) CONDITIONS Shock level: 1470 m/s2 (150G) Waveform: half sinusoidal wave, 2 ms Number of shocks: one shock input in each direction of three mutually perpendicular axis for a total of six shock inputs Vibration level: 9.8 m/s2 (1.0G) Waveform: sinusoidal Frequency range: 5 to 500 Hz Frequency sweep rate: 0.5 octave/min Duration: one sweep from 5 to 500 to 5Hz in each of three mutually perpendicular axis (total 3hr)
Vibration (non-operating)
9.3.
Judgment Standard Pass/Fail criteria for reliability tests is defined as follow: Pass: Normal display image with no obvious non-uniformity and no line defect. Fail : No display image, obvious non-uniformity, or line defect.
SIZE
A
REV.
A SHEET 17
OF
21
10.
10.1. 10.1.1. 10.1.2.
10.2. ITEM
Life Time
TL
IL=5.0mA,Ta=25C
SIZE
A
REV.
A SHEET 18
OF
21
12.
HANDLING PRECAUTIONS FOR TFT-LCD MODULE - Please observe the recommendations included in this paragraph when handling the TFT-LCD modules!
ASSEMBLY PRECAUTIONS Please use the mounting hole on the module corners for installation and avoid bending or wrenching LCD during assembly process. Do not drop, bend or twist the TFT-LCD module during handling. Guidelines for designing the TFT-LCD module enclosure: Housing case must be designed carefully so as not to put stresses on LCD all sides and not to wrench module. Mechanical stress to the TFT-LCD module may degrade the reliability and overall performances of the display (like brightness uniformity degradationetc.). Keep sufficient clearance between LCD module back surface and housing when the LCD module is mounted. Approximately 1.0 mm of the clearance in the design is recommended taking into account the tolerance of LCD module thickness and mounting structure height on the housing. When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD module, still sufficient clearance is required, such as 0.5mm. This clearance is, especially, to be reconsidered when additional parts are inserted for EMI countermeasures. Choose carefully the inverter location to avoid any stress to the lamp cable. The lamp cable also should not interfere with the module installation into the enclosure. Keep sufficient clearance between LCD module and the others components, such as inverter and speaker so as not to interfere with the LCD module. Approximately 1.0 mm of the clearance in the design is recommended. Do not apply pressure or scratch LCD panel surface with anything hard. Do not soil LCD panel surface by touching with bare hands. (Polarizer film, surface of LCD panel is easy to be flawed.) Do not apply pressure on any parts on the rear side such as source TCP, gate TCP, control circuit board and FPCs during handling LCD module. If applying pressure to the TFT-LCD module is unavoidable, handle the LCD module with care not to damage them. Wipe out LCD panel surface with absorbent cotton or soft cloth to clean the surface. Wipe out immediately any liquids which may have accidentally being sprayed on LCD panel surface. Droplets on the LCD panel surface may alter the quality of the image. Do not disassemble the TFT-LCD module for any reasons. By doing so you void the warranty of the TFT-LCD module and is very likely that the performances will be degraded considerably. Do not touch metal frames with bare hands and soiled gloves. If fingerprints or dirt are not cleaned immediately with solvent it is very likely that permanent marks will be left on the metal surfaces. Disconnect the lamp wires before handling the inverter otherwise is possible to damage the lamp and or the lamp wires by pulling it together with the inverter.
12.1. 12.1.1.
12.1.2. 12.1.2.1.
12.1.2.2.
12.1.2.3.
12.1.2.4. 12.1.2.5.
12.1.3.
12.1.4.
12.1.8.
12.1.9.
12.2.3.
12.2.4.
12.2.5.
OPERATING PRECAUTIONS Turn off the power supply before connecting and disconnecting signal input cable. Do not change the setting of the adjustable resistors on TFT-LCD module subassemblies. The adjustable resistors are properly set at the factory and any deviation from the factory setting will compromise the performances of the TFT-LCD module. When evaluating the optical characteristics of the display please note that will take longer time for the backlight to stabilize if the ambient temperature is at the lower end of the temperature range. Sudden changes of the ambient temperature may cause condensation on various surfaces of the TFT-LCD module and degrade the overall performances until the surfaces become dry again. Follow-up the general safety rules applying to generic electronic products.
SIZE
A
REV.
A SHEET 20
OF
21
12.3. 12.3.1.
12.3.2.
PRECAUTIONS WITH ELECTRONICS This LCD module uses CMOS integrated circuits and other components subject to be affected by electrostatic discharges. Use ESD protection equipment and follow all ESD safety procedures when handling the TFT-LCD modules. Please remove protection film very slowly from the surface of LCD module to prevent from high level electrostatic discharges. It is recommended to lift the protection film starting from the corner of the glass in proximity of the source and gate PWB ending at the corner of the glass furthest away from the electronics.
STORAGE PRECAUTIONS When you store LCDs for a long time, it is recommended to keep the temperature between 0C ~ 40 C without the exposure of sunlight and to keep the humidity less than 90%RH. Do not leave the LCDs in the environment of high humidity and high temperature such as 60C 90%RH. Do not expose the TFT-LCD modules to temperatures below 20C. SAFETY PRECAUTIONS When disposing LCDs it is recommended to break them into pieces. The broken pieces should be washed with solvents such as acetone and ethanol. The residual solvent from this process should be burned. If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash it off thoroughly with soap and water.
12.5. 12.5.1.
12.5.2.
12.6. 12.6.1.
OTHERS Exposing the TFT-LCD module to strong incident light may negatively affect the display characteristics because of polarizer film, color filter, and other materials degradation. Do not expose LCD module to direct sunlight or light with strong ultraviolet content. Avoid any contact of the TFT-LCD module front surface with other objects or materials. Packaging and shipping Packaging box and inner case for LCD are designed to protect the LCDs from the damage or scratching during transportation. Do not open the packaging box unnecessarily. Do not stack more than 5 boxes on top of each other because stack of 5 is maximum designed limit. Do not turn over the boxes. Avoid excessive shock, the shipping boxes are not designed to be thrown. Excessive vibrations can also damage the boxes and the TFT-LCD modules inside. Packaging box and the inner structures of it are made of cardboard. Avoid to have the boxes in contact with water or in high humidity environment which may cause the carton to become soft, or to break, damaging the TFT-LCD modules inside.
SIZE
A
REV.
A SHEET 21
OF
21