Documente Academic
Documente Profesional
Documente Cultură
MODEL : 32LD350
CAUTION
32LD350-UB
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Printed in Korea
CONTENTS
CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ......................................................................... 3 SPECIFICATION ....................................................................................... 6 ADJUSTMENT INSTRUCTION .............................................................. 10 EXPLODED VIEW .................................................................................. 16 SVC. SHEET ...............................................................................................
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
-2-
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
AC Volt-meter
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
0.15uF
1.5 Kohm/10W
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
-3-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500F to 600F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500F to 600F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500F to 600F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
-4-
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.
-5-
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This spec sheet is applied all of the 19, 22, 26, 32 LCD TV with LA04A chassis.
3. Test method
1) Performance: LGE TV test method followed 2) Demanded other specification - Safety : UL, CSA, IEC specification - EMC: FCC, ICES, IEC specification
Model 19LD350-UB Market Appliance North America Safety : UL1492, CSA C22.2.No.1, EMC : FCC Class B, IEC Class B
4. General Specification(TV)
No 1 2 Item Receivable System Available Channel 1) ATSC / NTSC-M VHF : 02 ~ 13 UHF : 14 ~ 69 DTV : 02 ~ 69 CATV : 01 ~ 135 CADTV : 01 ~ 135 3 4 5 Input Voltage Market Screen Size 1) AC 100 ~ 240V 50/60Hz North America 19 inch Wide(1366x 768) 22 inch Wide(1366x 768) 26 inch Wide(1366x 768) 32 inch Wide(1366x 768) 6 7 8 Aspect Ratio Tuning System LCD Module 16:9 FS CMO 18.5 HD 60 CCFL LC190WH1-TLC1 CMO 21.6 HD 60 CCFL LC220WXE-TBA1 Sharp 26 HD 60 CCFL T260XW04-V3 T315XW03-V1 9 10 Operating Environment Storage Environment Temp : 0 ~ 40 deg Humidity : ~ 80 % Temp : -20 ~ 60 deg Humidity : -85 % CMO LGD(V4) CMO LGD(V4) Sharp AUO AUO HD HD HD HD 19LD350-UB 22LD350-UB 26LD350-UB 32LD350-UB Specification Remark
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
-6-
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
-7-
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
-8-
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
-9-
ADJUSTMENT INSTRUCTION
1. Application range
This spec. sheet applies to LA04A Chassis applied LCD TV all models manufactured in TV factory
4. Automatic Adjustment
4.1. ADC Adjustment
(1) Overview ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device and to compensate RGB deviation. (2) Equipment & Condition 1) Jig (RS-232C protocol) 2) MSPG-925 Series Pattern Generator(MSPG-925FA) - Resolution : 480i Comp1 (MSPG-925FA: model-209, pattern-65) - Resolution : 1024*768 RGB (Inner Pattern) - Pattern : Horizontal 100% Color Bar Pattern - Pattern level : 0.70.1 Vp-p - Image
2. Specification
2.1 Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. 2.2 AdjThe adjustment must be performed in the circumstance of 25 5 C of temperature and 6510% of relative humidity if there is no specific designation. 2.4 The input voltage of the receiver must keep 100~240V, 50/60Hz. 2.5 The receiver must be operated for about 5 minutes prior to the adjustment when module is in the circumstance of over 15 In case of keeping module is in the circumstance of 0C, it should be placed in the circumstance of above 15C for 2 hours In case of keeping module is in the circumstance of below -20C, it should be placed in the circumstance of above 15C for 3 hours,. Caution) When still image is displayed for a period of 20 minutes or longer (especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.
(3) Adjustment 1) Adjustment method - Using RS-232, adjust items listed in 3.1 in the other shown in 4.1.3.3 2) Adj. protocol
Protocol Enter adj. mode Source change Command aa 00 00 xb 00 40 xb 00 60 Begin adj. ad 00 10 OKx (Case of Success) NGx (Case of Fail) Read adj. data (main) ad 00 20 (sub) ad 00 21 Confirm adj. ad 00 99 (main) 000000000000000000000000007c007b006dx (Sub) 000000070000000000000000007c00830077x NG 03 00x (Fail) NG 03 01x (Fail) NG 03 02x (Fail) a 00 OK00x b 00 OK40x (Adjust 480i Comp1 ) b 00 OK60x (Adjust 1024*768 RGB) Set ACK
3. Adjustment items
3.1 Board Level Adjustment
Adjust 480i Comp1(ADC) EDID/DDC download Above adjustment items can be also performed in Final Assembly if needed. Both Board-level and Final assembly adjustment items can be check using In-Star Menu 1.ADJUST CHECK. Component 1080p and RGB-PC Adjust will be calculated by 480i adjust value.
3.3 Etc
Ship-out mode Service Option Default USB Download(S/W Update, Option, Service only) ISP Download (Optional)
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
[Enter ADC adj. mode] [Change input source to Component1(480i)] [Adjust 480i Comp1] [Change input source to RGB(1024*768)] [Adjust 1024*768 RGB] End adj.
- 10 -
5. Manual Adjustment
5.1. ADC(Saturn5) Adjustment
(1) Overview ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device and to compensate RGB deviation. (2) Equipment & Condition 1) Adjust Remocon 2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator - Resolution: 480i, 1024*768 - Pattern : Horizontal 100% Color Bar Pattern - Pattern level: 0.70.1 Vp-p - Image
3) Must use standard cable (3) Adjust method ADC 480i/1080p Comp1, RGB 1) Check connected condition of Comp1 cable to the equipment 2) Give a 480i Mode, Horizontal 100% Color Bar Pattern to Comp1. (MSPG-925FA -> Model: 209, Pattern: 65) 3) Change input mode as Component1 and picture mode as Standard 4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then, select 5.ADC Calibration. And Press OK Button on the menu Start. The adjustment will start automatically. 5) If ADC Comp 480i is successful, ADC Component Success is displayed and Comp480i/1080p is completed. If ADC calibration is failure, ADC Component Fail is displayed. 6) If ADC calibration is failure, after rechecking ADC pattern or condition, retry calibration 7) After completing ADC Component, input mode will be changed to RGB automatically. 8) If ADC calibration is successful, ADC RGB Success is displayed. If ADC calibration is failure, ADC RGB Fail is displayed. 9) If ADC calibration is failure, after recheck ADC pattern or condition, retry calibration
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
- 11 -
RS -232C
Co m p ut er
RS -232C RS -232C
Connection Diagram of Automatic Adjustment (4) Adj. Command (Protocol) 1) RS-232C Command used during auto-adj.
RS-232C COMMAND Meaning [CMD wb wb ID 00 00 DATA] 00 ff Begin White Balance adj. End White Balance adj.(Internal pattern disappeared)
Ex) wb 00 00 -> Begin white balance auto-adj. wb 00 10 -> Gain adj. ja 00 ff -> Adj. data jb 00 c0 ... ... wb 00 1f -> Gain adj. complete *(wb 00 20(start), wb 00 2f(end)) -> Off-set adj. wb 00 ff -> End white balance auto adj.
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
- 12 -
* Adj. condition and cautionary items 1) Lighting condition in surrounding area Surrounding lighting should be lower 10 lux. Try to isolate adj. area into dark surrounding. 2) Probe location - LCD: Color Analyzer (CA-210) probe should be within 10cm and perpendicular of the module surface (80~ 100) 3) Aging time - After Aging Start, Keep the Power ON status during 5 Minutes. - In case of LCD, Back-light on should be checked using no signal or Full-white pattern. (6) Reference (White Balance Adj. coordinate and color temperature) Luminance: 216 Gray Standard color coordinate and temperature using CS1000 (over 26 inch) 26/32LD350-UB
Mode Color Coordination x COOL MEDIUM WARM 0.269 0.285 0.313 y 0.273 0.293 0.329 13000K 9300K 6500K 0.0000 0.0000 0.0000 Temp UV
(5) Adj. method Auto adj. method 1) Set TV in adj. mode using POWER ON key 2) Zero calibrate probe then place it on the center of the Display 3) Connect Cable(RS-232C) 4) Select mode in adj. Program and begin adj. 5) When adj. is complete (OK Sing), check adj. status pre mode (Warm, Medium, Cool) 6) Remove probe and RS-232C cable to complete adj. * W/B Adj. must begin as start command wb 00 00 , and finish as end command wb 00 ff, and Adj. offset if need Manual adj. method 1) Set TV in Adj. mode using POWER ON 2) Zero Calibrate the probe of Color Analyzer, then place it on the center of LCD module within 10cm of the surface.. 3) Press ADJ key -> EZ adjust using adj. R/C > 6. WhiteBalance then press the cursor to the right (KEYG ). (When KEY(G ) is pressed 216 Gray internal pattern will be displayed) 4) One of R Gain / G Gain / B Gain should be fixed at 192, and the rest will be lowered to meet the desired value. 5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of color temperature. - If internal pattern is not available, use RF input. In EZ Adj. menu 6.White Balance, you can select one of 2 Test-pattern: ON, OFF. Default is inner(ON). By selecting OFF, you can adjust using RF signal in 216 Gray pattern.
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
- 13 -
6.2. Checkpoint
TEST voltage - GND: 1.5KV/min at 100mA - SIGNAL: 3KV/min at 100mA TEST time: 1 second TEST POINT - GND TEST = POWER CORD GND & SIGNAL CABLE METAL GND - Internal Pressure TEST = POWER CORD GND & LIVE & NEUTRAL LEAKAGE CURRENT: At 0.5mArms
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
- 14 -
(5) Updating Completed, The TV will restart automatically (6) If your TV is turned on, check your updated version and Tool option. (explain the Tool option, next stage) * If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didnt have a DTV/ATV test on production line. * After downloading, have to adjust TOOL OPTION again. 1) Push "IN-START" key in service remote controller. 2) Select "Tool Option 1" and Push OK button. 3) Punch in the number. (Each model has their number.)
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
- 15 -
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
400
520
800
540
530
810
910
200
550
510
Copyright LG Electronics. Inc. All right reserved. Only for training and service purposes
300
500
120
900
- 16 -
NUMONIX
IC102-*1 NAND512W3A2CN6E NC_1 NC_2 NC_3 NC_4 NC_5 NC_6 RB R E NC_7 NC_8 VDD_1 VSS_1 NC_9 NC_10 CL AL W WP NC_11 NC_12 NC_13 NC_14 NC_15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 NC_29 NC_28 NC_27 NC_26 I/O7 I/O6 I/O5 I/O4 NC_25 NC_24 NC_23 VDD_2 VSS_2 NC_22 NC_21 NC_20
IC102 HY27US08121B-TPCB
+3.3V_Normal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
48 47 46 45 44 43 42 41 40 39 38 37
S5 Reset
001:V17 D4 AC16 AA15 SW100 +3.5V_ST R187 1K POWER_DET PCM_A[4] VCC R113 1K OPT IC103 MAX810RTR 4 2 3 1 GND 10K R133 2 RESET R228 100 C B Q108 2SC3052 E S5/S6_Reset R135 100 PCM_A[0] PCM_A[1] PCM_A[2] PCM_A[3] PCM_A[4] PCM_A[5] C120 4.7uF 10V R134 10K C121 10uF 6.3V PCM_A[6] PCM_A[7] R2172 OPT R2123 OPT PCM_A[3] PCM_A[2] PCM_A[1] PCM_A[0] R2124 OPT R178 OPT 33 33 33 33 3 1 AA16 AC6 Y10 Y11 Y12 Y13 AB16 AC15 AC14 AB14 AC12 AB8 AC13 AA9 AB5 AA4 V4 Y4 AB9 AA7 AD6 AA14 AB18
IC100 MSD3159GV
HWRESET B3 XIN XOUT PCMD0/CI_D0 PCMD1/CI_D1 PCMD2/CI_D2 PCMD3/CI_D3 PCMD4/CI_D4 PCMD5/CI_D5 PCMD6/CI_D6 PCMD7/CI_D7 PCM_A0/CI_A0 PCM_A1/CI_A1 PCM_A2/CI_A2 PCM_A3/CI_A3 PCM_A4/CI_A4 PCM_A5/CI_A5 PCM_A6/CI_A6 PCM_A7/CI_A7 PCM_A8/CI_A8 PCM_A9/CI_A9 PCM_A10/CI_A10 PCM_A11/CI_A11 R253 PCM_A12/CI_A12 PCM_A13/CI_A13 PCM_A14/CI_A14 10K +3.5V_ST USB_DP_1 USB_DM_1 USB_DM_2 USB_DP_2 B5 A5 AC10 AB10 SPI_DI SPI_DO /SPI_CS SPI_CK AE11 AF12 AE12 AD11 R226 R227 33 33 R225 33 TESTPIN/GND E6 A3 R231 R232 0 0 R252 X100 1M 12MHz
C186
20pF
S5/S6_Reset
C187
20pF
AR100
I/O7 I/O6 I/O5 I/O4 NC_24 NC_23 PRE VCC_2 VSS_2 NC_22 NC_21 NC_20 C162 0.1uF C161 10uF 6.3V PCM_A[7] PCM_A[6] PCM_A[5]
+3.5V_ST
PCM_A[0-7]
R156
R158
22
R157 1K
OPT
NC_8 VCC_1
C131 0.1uF
HYNIX
36 35 34 33 32 31 30 29 28 27 26 25
R153
10K
AR101
I/O3 I/O2 I/O1 I/O0 NC_19 NC_18 NC_17 NC_16
22
E5 PCM_RST/CI_RST PCM_CD/CI_CD /PCM_OE PCM_REG/CI_CLK PCM_WAIT/CI_WACK /PCM_IRQA /PCM_WE PCM_IOWR/CI_WR PCM_IOR/CI_RD /PCM_CE /PF_CE0 /PF_CE1 /PF_OE /PF_WE PF_ALE PF_AD15 F_RBZ LHSYNC2/I2S_OUT_MUTE/RX1 LVSYNC/GPIO133 UART2_TX/SCKM UART2_RX/SDAM DDCR_DA DDCR_CK GPIO79/LVSYNC2/TX1 UART2_RX/GPIO84 UART2_TX/GPIO85 UART1_RX/GPIO86 UART1_TX/GPIO87 DDCA_CLK DDCA_DA UART_RX2 UART_TX2 TS0_D0 TS0_D1 TS0_D2 GPIO42/PCM2_CE_N GPIO43/PCM2_IRQA_N AA8 Y8 Y9 AB7 AA6 AB6 U4 AC5 AC4 AD5 AB4 AB19 TS1_D0 AA20 AC19 AA19 C10 ET_TXD0 ET_TXD1 SAR0 SAR1 SAR2 SAR3 IRIN ET_TX_CLK ET_RXD0 ET_RXD1 ET_TX_EN ET_MDC ET_MDIO ET_COL GPIO44 B11 A9 C11 C9 B10 A10 B9 A11 E7 AC18 C6 F9 F10 A6 B6 AF5 AF10 GPIO_PM0/GPIO134 GPIO_PM1/GPIO135 GPIO_PM2/GPIO136 GPIO_PM3/GPIO137 GPIO_PM4/GPIO138 GPIO_PM5/INT1/GPIO139 GPIO_PM6/INT2/GPIO140 GPIO131/LDE/SPI_WPn1 GPIO130/LCK GPIO132/LHSYNC/SPI_WPn GPIO60/PCM2_RESET/RX1 GPIO62/PCM2_CD_N/TX1 F5 G5 H5 F6 G6 H6 AC17 AB17 AF11 AA18 AA17
R237 R2221 R244 R245 R251 R2222 R2193 R220 R238 R239 R240
004:E21 007:M21
RL_ON DBG_TX INV_CTL PANEL_CTL POWER_ON/OFF1 DBG_RX POWER_DET POWER_ON/OFF2_1 POWER_ON/OFF2_2 Flash_WP_1 SDA1 SCL1
Y5 AB15 AA10 AC8 AC7 AA5 AR103 /PF_CE0 /PF_CE1 /PF_OE /PF_WE PF_ALE PF_WP +3.3V_Normal /F_RB +5V_Normal EEPROM_SCL L104 L105 OPT EEPROM_SDA SDA0 SCL0 ISP Debug port for S5
A0 1 8 VCC
100 007:R23 100 007:O27;007:Q25;004:E21;010:AG9 001:AB27;004:AE8 100 100 100 100 0 0 007:AH18;007:AN26 007:AH18;007:AN26 001:C11 001:AN6 001:AN6
W4 T4 AE6 AF6
001:S10 001:T8 001:S10 001:T7 001:T8 001:Q7 001:S11 001:H6;001:O16;001:AO8 R215 001:H5;001:O16;001:AO8 R216 001:AN7 001:AN6 004:AB26 001:AR31;004:AB26 R217 R218 R191 R192 R183 R184 22 0 0 0 0 22 22 22 22 AR102 22
0 22 0 22 22 22 22 22 HDMI_4
001:AI8;010:Q25 001:AI8;010:Q24
FE_TUNER_SCL FE_TUNER_SDA
+3.3V_Normal
HDCP EEPROM
EEPROM
IC105 CAT24WC08W-T
IC104 AT24C512BW-SH-T
R106 4.7K
A0 1 A1 A2 VSS 2 3 4
$0.199
C100 0.1uF
WP
A1
OPT TS_DATA[0] TS_DATA[1] TS_DATA[2] TS_DATA[3] TS_DATA[4] TS_DATA[5] TS_DATA[6] TS_DATA[7] 010:AC19;010:AK20 010:AC20;010:AK19 010:AC19;010:AK19 R2173 OPT 100 R2175 OPT 100 R2174 OPT 100 R2176 OPT 100 004:F5 R235 R243 R110 R2188 R249 R250 R2189 100 100 100 100 100 100 100 010:AJ26 VSB_RESET SIDE_HP_MUTE SIDE_AV_OPT 004:AN15 TS_SYNC TS_VALID TS_CLK
DBG_TX
A2
SCL
GND
SDA
PWM0 PWM1 PWM2 PWM3 Stand-by GPIO(SAR[0-3]) 10 : BOOT 51 11 : BOOT RISC OPT R147 1K R150 1K A_DIM 007:A23 PWM0 001:AB24;001:AL12 R151 OPT R148 1K 1K PWM1 001:AB24;001:AL12 AMP_RST LED_B/LG_LOGO 007:N19;008:V15;008:AE24 R115 100 PWM_DIM 007:N19;008:V15;008:AE24 C181 1uF C182 1uF OPT R186 OPT R189 100 001:AB23 PWM2 100 001:N10;001:AB24 PWM1 R185 1.2K 001:N11;001:AB24 PWM0 KEY1 KEY2 LED_R/BUZZ SB_MUTE IR
001:N11;001:AL12 001:N10;001:AL12 001:AL12 001:AL12 004:B28;004:D12 004:B27;004:D11 R2190 007:A23 001:H16;001:AR32 004:I24;004:AD4 R193 0 R2191 0 0 TP806 R195 100
+3.3V_Normal
PWM Dimming
AV_CVBS_DET
R111 OPT100
R112 001:AB23 PWM3 006:K19 R200 R248 R221 +3.5V_ST ERROR_OUT NTP_MUTE 007:M20 001:H15 R201 R219 R255
AC11 D9 D10 D7 E11 E8 E10 D6 D5 C5 GPIO96 GPIO88 GPIO90/I2S_OUT_MUTE GPIO91 GPIO97 GPIO98 GPIO99 GPIO103/I2S_OUT_SD3 GPIO102
R28310K FHD
OLP
001:H15
R280 10K
I2C
+5V_Normal
+3.3V_Normal
D6 R284 0 OPT
D7 R285 0 FHD
R28110K HD
B9 0 R287 HD
R2109 1.2K
R2107 1.2K
R2108 1.2K
R2110 1.2K
R260 3.3K
R266 3.3K
Audio Mute
+3.5V_ST ---------------------HIGH LOW D6 LCD PDP D7 B_LVDS A_LVDS E11 MOVING : PWM R/B B9 FHD HD ----------------------
R2100 R2101
0 0
A7 GPIO67 GPIO68 B8
R224 R242
100 100
0 0
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
MMAIN_SOC_1
LD350 MAIN_SOC_1
09.09.03
+3.3V_VDDP
+1.26V_VDDC C164 0.1uF C163 330uF OPT C166 0.1uF C169 0.1uF C172 0.1uF C175 0.1uF C178 0.1uF C183 0.1uF C188 0.1uF C193 0.1uF C198 0.1uF C2104 0.1uF C2109 0.1uF C2115 0.1uF C2119 0.1uF C2120 0.1uF C2123 0.1uF C2124 0.1uF C2125 0.1uF C2126 0.1uF C2127 0.1uF C2128 0.1uF C2129 0.1uF C2130 0.1uF C2131 0.1uF C2132 0.1uF C2133 0.1uF C2134 0.1uF C2135 0.1uF C2136 0.1uF C2137 0.1uF C167 0.1uF C170 0.1uF C173 0.1uF C176 0.1uF C179 0.1uF C184 0.1uF
+3.3V_Normal
L101 BLM18PG121SN1D
C189 0.1uF
C195 0.1uF
C196 0.1uF
+1.8V_DDR
C168 0.1uF
C171 0.1uF
C174 0.1uF
C177 0.1uF
C180 0.1uF
C185 0.1uF
C190 0.1uF
C194 0.1uF
C199 0.1uF
C2105 0.1uF
C2110 0.1uF
C2111 10uF
IC100 MSD3159GV
HDMI1/2/3(Side)
F1 RXACKP F2 RXACKN G2 RXA0P G3 RXA0N H3 RXA1P G1 RXA1N H1 RXA2P H2 RXA2N A1 DDCD_A_DA B2 DDCD_A_CK A2 HOTPLUG_A 005:H16 005:H17 005:H15 005:H16 005:H14 005:H15 005:H13 005:H14 005:H18;005:AH18 005:H18;005:AH19 005:H19 005:H7 005:H7 005:H6 005:H6 005:H5 005:H5 005:H4 005:H4 005:H8;005:AH12 005:H8;005:AH13 005:G10 005:L26 CEC_REMOTE R142 R143 R144 R145 0 0 220 100 HDMI_4 HDMI_4 HDMI_4 R2116 R2117 R2118 0 0 220 HDMI_2 HDMI_2 HDMI_2 C3 RXBCKP B1 RXBCKN C1 RXB0P C2 RXB0N D2 RXB1P D3 RXB1N E3 RXB2P D1 RXB2N E1 DDCD_B_DA F3 DDCD_B_CK E2 HOTPLUG_B AE8 RXCCKP AD8 RXCCKN AD9 RXC0P AF8 RXC0N AF9 RXC1P AE9 RXC1N AE10 RXC2P AD10 RXC2N AE7 DDCD_C_DA AF7 DDCD_C_CK AD7 HOTPLUG_C J3 CEC AA3 AUR0 AUL0 AUR1 AUL1 Y1 AE1 AF3 C134 C135 C136 C137 C138 C139 2.2uF SIDE_AV_OPT 2.2uF SIDE_AV_OPT 2.2uF 2.2uF 2.2uF 2.2uF AE16 LVA0P LVA0M LVA1P LVA1M LVA2P LVA2M LVA3P LVA3M LVA4P LVA4M AE14 LVACKP LVACKM AE20 LVB0P LVB0M LVB1P LVB1M LVB2P LVB2M LVB3P LVB3M LVB4P LVB4M AE18 LVBCKP LVBCKM AD18 AD20 AD19 AF20 AF19 AE19 AD17 AF18 AF17 AE17 AD14 CK+_HDMI2 CK-_HDMI2 D0+_HDMI2 D0-_HDMI2 D1+_HDMI2 D1-_HDMI2 D2+_HDMI2 D2-_HDMI2 DDC_SDA_2 DDC_SCL_2 HPD2 CK+_HDMI4 CK-_HDMI4 D0+_HDMI4 D0-_HDMI4 D1+_HDMI4 D1-_HDMI4 D2+_HDMI4 D2-_HDMI4 DDC_SDA_4 DDC_SCL_4 HPD4 AD16 AD15 AF16 AF15 AE15 AD13 AF14 AF13 AE13
TXA0+[10],TXA0-[11],TXA1+[8],TXA1-[9],TXA2+[6],TXA2-[7],TXA3+[2],TXA3-[3],TXA4+[0],TXA4-[1],TXAC+[4],TXAC-[5]
AR104 22 FHD
IC100 MSD3159GV
E16 E17 E18 F7 L9 L10 L11 GND_2 GND_3 GND_4 GND_5 GND_6 GND_7 GND_8 VDDC_1 VDDC_2 VDDC_3 VDDC_4 VDDC_5 VDDC_6 VDDC_7 VDDC_8 VDDC_9 L12 L13 L14 L15 L16 L17 L18 M9 M10 M11 M12 M13 M14 M15 M16 M17 M18 N4 N9 N10 N11 N12 N13 N14 N15 N16 GND_33 GND_34 GND_35 GND_36 GND_37 GND_38 GND_39 AVDD_DDR_1 AVDD_DDR_2 AVDD_DDR_3 GND_40 GND_41 GND_42 GND_43 GND_44 GND_45 GND_46 GND_47 R4 GND_48 GND_49 GND_50 GND_51 GND_52 GND_53 GND_54 GND_55 R16 R17 AUDIO_MASTER_CLK MS_LRCK MS_SCK MS_LRCH R18 T5 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 U5 W13 Y21 AA23 GND_64 GND_65 GND_66 GND_67 GND_68 GND_69 GND_70 GND_71 GND_72 GND_73 AVDD_USB H8 AVDD_DM W8 GND_56 GND_57 GND_58 GND_59 GND_60 GND_61 GND_62 GND_63 AVDD_33_1 AVDD_33_2 AVDD_33_3 AVDD_33_4 AVDD_33_5 J7 K7 L7 M7 N7 AVDD_MPLL H7 AVDD_LPLL R20 AVDD_DDR_4 AVDD_DDR_5 AVDD_DDR_6 AVDD_DDR_7 AVDD_DDR_8 AVDD_DDR_9 AVDD_DDR_10 AVDD_DDR_11 H17 AVDD_MEMPLL_1 AVDD_MEMPLL_2 AVDD_MEMPLL_3 T20 V20 G12 G13 H13 H14 H15 H16 W14 W15 W16 W17 W18 AVDD_AU W7 N17 N18 P4 P9 P10 GND_25 GND_26 GND_27 GND_28 GND_29 GND_30 GND_31 GND_32 VDDP_1 VDDP_2 VDDP_3 VDDP_4 VDDP_5 VDDP_6 VDDP_7 VDDP_8 H9 H10 H11 H12 N20 P20 W9 W10 GND_19 GND_20 GND_21 GND_22 GND_23 GND_24 GND_9 GND_10 GND_11 GND_12 GND_13 GND_14 GND_15 GND_16 GND_17 GND_18 VDDC_10 VDDC_11 VDDC_12 VDDC_13 VDDC_14 VDDC_15 VDDC_16 VDDC_17 VDDC_18 VDDC_19 VDDC_20 VDDC_21 VDDC_22 VDDC_23 VDDC_24 VDDC_25 VDDC_26 VDDC_27 D16 D17 D18 D19 D20 H18 H19 H20 J20 K20 L20 M20 P7 R7 T7 T22 U7 U20 U22 V7 V22 W11 W12 W19 W20 W22 Y22
+1.26V_VDDC
AR105 22 FHD
AR106 22 FHD
AR107 22
AR108 22
+3.3V_VDDP
COMPONENT1
COMP1_PR COMP1_Y COMP1_PB 004:Y6 004:Y4 004:Y5 R120 R121 R122 R123 R124 R125 R126 47 47 47 470 47 47 47 C101 C102 C103 C104 C105 C106 C107 0.047uF 0.047uF 0.047uF 1000pF 0.047uF 0.047uF 0.047uF
AE3 AUR2 AUL2 AE2 AA1 AUR3 AB1 AUL3 AB2 AUR4 AC2 AUL4 AB3 AUR5 AC3 AUL5
004:AO21 004:AO20
PC_R_IN PC_L_IN
W3 SIF0P SIF0M W2
C146 C147
0.1uF 0.1uF
R171 R172
47 47 R2220 0
010:P20 010:P19
FE_SIF SIFMO
DSUB
DSUB_HSYNC DSUB_VSYNC DSUB_R DSUB_G DSUB_B 004:R23 004:R24 004:R20 004:R21 004:R23 R107 10K C110 68pF R109 10K C111 68pF V1 RIN2P/COMP_PR+ V2 GIN2P/COMP_Y+ U1 BIN2P/COMP_PB+ V3 SOGIN2 J5 VSYNC2 R127 R128 R129 R130 47 47 47 470 R146 R149 C113 C108 C114 C109 22 22 0.047uF 0.047uF 0.047uF 1000pF K3 HSYNC1/DSUB_HSYNC K2 VSYNC1/DSUB_VSYNC L1 RIN1P/DSUB_R L3 GIN1P/DSUB_G K1 BIN1P/DSUB_B L2 SOGIN1
+3.3V_Normal L106 BLM18PG121SN1D C200 C206 C209 0.1uF C216 0.1uF +3.3V_Normal L108 BLM18PG121SN1D +3.3V_AVDD_MPLL
AF1 AUOUTR0/HP_ROUT AUOUTL0/HP_LOUT AUOUTR1/SC1_ROUT AUOUTL1/SC1_LOUT AUOUTR2/SC2_ROUT AUOUTL2/SC2_LOUT AF2 AD3 AD1 AC1 AD2
R164 R165 R166 OPT R167 OPT R168 OPT R169 OPT
100 100 100 100 100 100 C151 0.01uF C153 0.01uF C156 0.01uF C158 0.01uF C159 0.01uF C160 0.01uF R170 22K R173 22K R174 22K R175 22K R176 22K
006:K18 006:K18
0.1uF 0.1uF
R177 22K
OPT
C211 0.1uF
C218 0.1uF
OPT
OPT
OPT
OPT
A8 I2S_OUT_MCK
OPT
CVBS
SIDEAV_CVBS_IN AV_CVBS_IN 004:AN16 004:F4
B7 C7 D8 C8
C191 0.1uF
C201 10uF 10V +3.3V_Normal L103 BLM18PG121SN1D C204 0.1uF C205 0.1uF C202 0.1uF C203 0.1uF C207 0.1uF C214 0.1uF
M1 CVBS4/S-VIDEO_Y M2 CVBS6/S-VIDEO_C R140 47 47 100 100 100 TP803 C124 C125 C122 C123 0.047uF 0.047uF 0.047uF 0.047uF N3 CVBS5 M3 CVBS7 W1 CVBS0/RF_CVBS Y3 VCOM0 Y2 CVBSOUT0/SC2_MNTOUT AA2 CVBSOUT1
C127
0.1uF C148
C150 0.1uF
TV/MNT
FE_VMAIN VCOMO 010:S17 010:N15
R152 1%
390
+3.3V_Normal L107 +3.3V_Normal BLM18PG121SN1D C217 C210 L102 BLM18PG121SN1D 0.1uF 0.1uF C192 0.1uF C208 0.1uF
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Main_SOC_2
LD350 MAIN_SOC_2
09.09.03
+5V_Normal 5V_PANEL
+12V/+15V 12V_PANEL
+24V/+15V
+12V/+15V
+3.5V_ST +3.5V_ST R488 100K IC408 NCP803SN293 VCC RESET POWER_DET OPT R463 10K 2 1 C483 0.1uF OPT 4 R480 100
PANEL_POWER
L411
L412
R448-*1 16K
1/16W 5%
PD_+15V
Q409 AO3407A
New item
R446 30K
R448 12K
R450 14K
PANEL_VCC
L407 MLB-201209-0120P-N2
R423 0
GND
+3.5V_ST +12V
OPT
R482 20K IC409 NL17SZ08DFT2G
R431 22K
26"~32"
1 3 5 7 9 11 13 15 17 19 21 23
+15V 1
+15V 2
GND 3
GND 4
+3.5V_ST 5
3.5V_ST 6
GND 7
OLP 8
INV_EN 9
PWM_DIM10
A_DIM11
NC12
2 4 6 8 10 12 14 16 18 20 22 24
24V GND GND 3.5V 3.5V GND GND/OLP INV_ON A.DIM P.DIM Err_OUT/NC 26"~32" R412 1K 19"~22" R413 0
R483 10K
24V
Power_DET
UNDER CHECKING
+3.3V_Normal +3.5V_ST PANEL_CTL R419 1K OLP R426 10K R418 6.8K OPT E R409 0 19"~22" R453 0 A_DIM B C R421 10K INV_CTL +3.5V_ST 1:AK10 R429 47K B
2 R481 3K
R435 22K
CIC21J501NE L420
Vout=0.8*(1+R1/R2)
L416
Q405 2SC3052
+12V/+15V
+3.3V_Normal
+3.3V_Normal
1934 mA
OPT R407 10K OPT
R457 15K
+1.8V_DDR
IC405 AOZ1073AIL
PGND LX_2
Close to IC
Sharp
CMO(09) A-DIM NC
AUO INV_ON
SHARP INV_ON
1K R9825
R2 GND 2
+3.3V_Normal
3A
SW_2
R461 4.7K
FB
Err_out Err_out
R486 4.7K
Placed on SMD-TOP
IN
R462 10K
PWM_DIM GND
R437 0 AUO/SHARP R420 0 LGD
VCC
Placed on SMD-TOP
1%
1%
OPC_OUT
EN/SYNC
3A
EN
R460 27K
R479 0
IC407 MP2212DN
NON_OPC PWM_DIM
R1
R2
Vout=(1+R1/R2)*0.8
C465 1uF 10V
+3.3V_Normal +12V/+15V
L417
+15V Control
+24V/+15V
+5V_Normal
R404 33K OPT R408 10K OPT
MAX 1A
IC406 AOZ1073AIL
PGND LX_2
R468 22K
19"~22"
AMP_VCC
+12V/+15V
+12V
R451 22K
OPT
R428 2.2K
19"~22"
G Q410 C AO3407A
19"~22"
R466 1.5K
RT1C3904-T112 Q411
19"~22"
FB
POWER_ON/OFF1
R467 10K
1%
1%
AGND
3A
EN
5%
R465 51K
VIN
LX_1
R1
R405 0
R2
Vout=0.8*(1+R1/R2)
+3.3V_AVDD_MPLL
2026 mA
+5V_USB
+12V/+15V +5V_USB
L413
Replaced Part Vout=0.8*(1+R1/R2) R1 +3.3V_Normal R444 R402 100K 24K 1% OPT R425 120K 10K R445 OPT POWER_ON/OFF2_1 SW_2 L415 3.6uH NR8040T3R6N 6 SW_1 C453 22uF 10V C448 0.1uF 50V C456 0.1uF C403 0.1uF 16V C9810 22uF 10V IN GND OUT +1.26V_VDDC IC400 TJ3965S-3.3V-3L R442 22K 1% L400 BLM18PG121SN1D +3.5V_ST +3.3V_AVDD_MPLL
L401
IC401 MP8706EN-C247-LF-Z
IN GND C414 1uF 50V R410 10K POWER_ON/OFF1 R411 10K OPT OPT C482 100pF 50V
MAX 2000mA
IC403 MP2212DN
R416 33K 1% OPT C429 100pF 50V FB C420 22uF 10V C424 0.1uF 16V C428 0.1uF 16V R432 75K 1/8W 1% R2 GND 2
VCC
EN/SYNC
3A
FB
R1
R417 6.2K
1%
BST
EN/SYNC
3A
Placed on SMD-TOP
IN
R2
C IN +5V_USB C430 22uF 10V
BS
+3.3V_Normal
VCC
Placed on SMD-TOP
R441 R436
R474 10K
Vout=(1+R1/R2)*0.8 THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
10 1/10W 1%
09.09.03
R2404 10K 1%
2 L2406 BLM18PG121SN1D 19"~22" C2411 0.1uF 16V 19"~22" C2412 0.1uF 16V 19"~22" D2406 5.6V 19"~22" D2407 5.6V 19"~22" 3 4
26"~32" L2401 BLM18PG121SN1D D2402 5.6V AMOTECH 26"~32" EYEQ R2411 100 SCL_SUB/AMP C2408 1000pF 50V OPT SCL C2402 0.1uF 26"~32" D2401 5.6V AMOTECH 26"~32" EYEQ R2412 100 SDA_SUB/AMP C2409 1000pF 50V OPT D2404 CDS3C05HDMI1 5.6V OPT GND OPT D2403 CDS3C05HDMI1 5.6V P2401 12507WR-12L
SDA
KEY1
+3.5V_ST
KEY2
+3.5V_ST R2413 1.5K LED_B/LG_LOGO OPT C2410 0.1uF 16V R2410 100 C2407 100pF 50V L2404 BLM18PG121SN1D D2405 5.6V AMOTECH
ST_3.3V
R2429 47K
+3.5V_ST
GND
LED_B
C B Q2405 2SC3052 E
IR
+3.3V_Normal
GND
10
R2427 0 OPT
11
LED_R
12 13
COMMERCIAL
+3.5V_ST
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
09.09.03 6
HDMI EEPROM
5V_HDMI_2 +5V_Normal
A2
A0
A1
$0.055
2 7
WP
A2
SCL R7750 22
GND
HDMI_2
SHIELD
HDMI_4
5V_HDMI_2 5V_DET_HDMI_2 5V_HDMI_4 5V_DET_HDMI_4 C JACK_GND HPD2 20 E C7700 0.1uF 16V 3.3K OPT R7706 R7707 22 DDC_SDA_2 22 DDC_SCL_2 15 R7708 100 14 HDMI_CEC EAG42463001 13 12 11 10 9 8 R7712 0 R7713 0 D0+_HDMI2 D1-_HDMI2 7 6 5 R7714 0 R7715 0 D1+_HDMI2 D2-_HDMI2 4 3 2 R7716 0 D7701 D2+_HDMI2 1 CK+ D0D0_GND D0+ D1D1_GND D1+ D2D2_GND D2+ R7743 0 R7741 0 R7742 0 R7739 0 R7740 0 R7737 0 CK+_HDMI4 R7738 0 D0-_HDMI4 GND 4 5 SDA DDC_SDA_4 R7752 22 CK-_HDMI2 HDMI_4 R7735 100 HDMI_CEC R7736 0 CK-_HDMI4 A2 3 6 SCL DDC_SCL_4 R7751 22 R7730 1K R7731 R7732 1.8K 3.3K OPT C7702 0.1uF 16V Q7702 2SC3052 E B R7744 HPD4 10K C R7702 Q7701 2SC3052 B 5V_HDMI_4 +5V_Normal
R7729 10K
A2
$0.253
19 18 17 16 15 14 EAG59023301 13 12 11 10 9 8 7 6 5 4 3 2 1 CK+ D0D0_GND D0+ D1D1_GND D1+ D2D2_GND D2+
$0.253
19 18 17 16
HDMI_4 IC7702 R7733 R7734 22 22 AT24C02BN-10SU-1.8 R7757 DDC_SCL_4 10K DDC_SDA_4 A0 VCC
A1
ENKMC2838-T112 D7706
20
A1
ENKMC2838-T112 D7705
EEPROM_WP
$0.055
A1 2 7 WP C7705 0.1uF R7758 R7761 4.7K 4.7K
R7709 0
HDMI_2
R7710 0 R7711 0
CK+_HDMI2 D0-_HDMI2
D0+_HDMI4 D1-_HDMI4
D1+_HDMI4 D2-_HDMI4
D2+_HDMI4
For CEC
68K R7745 D7703
+3.5V_ST
JK7700
JK7702
D7702
R7762
10K
R7746 OPT 0
HDMI_CEC
CEC_REMOTE
VR7700 AVRL161A1R1NT
S B D
M1 MDS62110201
OPT
M2 MDS62110201
OPT
M3 MDS62110201
OPT
Q7703 BSS83
GND
GND
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
OPT
VR7701 AVRL161A1R1NT
LD350 HDMI
09.09.03 8
COMMON AREA
New Item Development
EARPHONE AMP
H/P_L +5V_EARPHONE +5V_Normal D1100 ENKMC2838-T112 A1
EARPHONE BLOCK
HP_LOUT R1119 0 1/10W 5% 2:X19
IC1100
002:Y10
TPA6110A2DGNRG4
BYPASS IN1-
C B B
+5V_EARPHONE
+5V_EARPHONE
GND
VO1
C1106 100uF 16V HP_LOUT R1117 1K C1111 1000pF OPT HP_ROUT HP_ROUT C1109 100uF 16V C1102 0.1uF 16V C1104 10uF 10V C1105 10uF 10V R1118 1K C1110 1000pF OPT 2:X19 R1120 0 1/10W 5% C1116 1000pF 50V OPT
R1155 1K HP_DET
R1109 16K
IN2-
VO2
PC AUDIO
JK1102 PEJ027-01 3 6A 7A 4 5 7B 6B E_SPRING T_TERMINAL1 B_TERMINAL1 PC_R_IN R_SPRING T_SPRING B_TERMINAL2 T_TERMINAL2 D1102 AMOTECH 5.6V OPT C1108 100pF 50V R1103 470K D1101 AMOTECH 5.6V OPT C1107 100pF 50V R1107 15K R1102 470K R1112 0 R1110 10K 2:S16
+3.3V_Normal
RGB PC
C A2
JST1223-001 JK1103
GND
AT24C02BN-10SU-1.8
A0
VCC
R1139 4.7K
R1140 4.7K
Fiber Optic
VCC
A1
WP
A2
GND
SCL
ISP_RXD
SDA
GND
FIX_POLE
DSUB_VSYNC
R1150 0 R1148 0
D1109 30V
D1113 30V
R1146 10K DSUB_DET R1147 1K DSUB_R R1137 75 C1125 OPT OPT D1112 30V D1117 5.6V
GREEN_GND
DDC_CLOCK
DDC_DATA
BLUE_GND
SYNC_GND
RED_GND
SPG09-DB-010
DDC_GND
H_SYNC
V_SYNC
GND_2
GREEN
GND_1
BLUE
RED
NC
JK1104
10
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
16
SHILED
11
12
13
14
15
09.09.03 9
RS-232C
C1229 0.33uF C1234 0.1uF 16V R1276 0
IC1201 MAX3232CDR
C1231 0.1uF C1+ VCC
JK1201 SPG09-DB-009
DBG_RX 1 DBG_TX RxD ADUC30S03010L ADUC30S03010L R1302 220 6 2 R1299 220 7 3 C1242 47pF 50V C1243 47pF 50V 8 4 9 5
R1279 4.7K
R1278 4.7K
R1275 0
16
15
GND
14
DOUT1
R1284 OPT100
TxD
13
RIN1
R1285
100 OPT
12
ROUT1
11
DIN1
10
10
DIN2
RIN2
ROUT2
IR_OUT
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
RS-232C
LD350 RS-232C
09.09.03
10
+3.3V_Normal
SIDE_AV_OPT 10K R3302 SIDE_AV_OPT R3305 1K
SIDE_AV_OPT R3306 SIDEAV_L_IN SIDE_AV_OPT 10K C3302 100pF 50V SIDE_AV_OPT R3307 SIDE_AV_OPT 10K C3303 100pF 50V SIDE_AV_OPT R3308 12K
SIDEAV_R_IN SIDE_AV_OPT D3304 5.6V SIDE_AV_OPT R3304 470K SIDE_AV_OPT R3309 12K
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
LD350 SIDE AV
09.09.03 11
USB_DIODES
IC1450 AP2191SG-13
NC L1451 MLB-201209-0120P-N2 120-ohm OUT_1 C1451 22uF 10V FLG 5 4 EN 6 3 IN_2 C1452 10uF 10V C1453 0.1uF +3.3V_Normal GND
8 $0.077 7
+5V_USB
OUT_2
IN_1
KJA-UB-4-0004 JK1450
R1451
47
USB_OCD
SIDE_USB_DM
SIDE_USB_DP
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
LD350 USB
09.09.03 14
0.1uF C41
0.1uF C27
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF C13
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF C25
0.1uF C29
0.1uF C32
0.1uF
0.1uF
0.1uF
0.1uF C33
0.1uF C34
0.1uF
0.1uF
0.1uF
0.1uF C30
10uF
10uF C14
10uF C24
C23
C36
C10
C12
C15
C17
C19
C11
C8
C20
C6
C21
C3
C5
C7
C9
1K 1%
R23
R47 1K
R4
1000pF
0.1uF
1K 1%
1% 0.1uF
1000pF
C16
C18
IC1-*1 A3R12E4JFF-G8E
VREF DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
C2
C4
R5
IC1 H5PS5162FFR-S6C
SDDR_D[0] SDDR_D[1] SDDR_D[2] SDDR_D[3] SDDR_D[4] SDDR_D[0-15] SDDR_D[5] SDDR_D[6] SDDR_D[7] SDDR_D[8] SDDR_D[9] SDDR_D[10] SDDR_D[11] SDDR_D[12]
A9 C1 C3 C7 C9 LDQS UDQS F7 B7 E9 G1 G3 G7 LDM UDM F3 B3 G9 VDDQ_10 VDDQ_9 VDDQ_8 VDDQ_7 VDDQ_6 VDDQ_5 VDDQ_4 VDDQ_3 VDDQ_2 VDDQ_1
R24
R44 1K
1K
MSD3159GV
D15 A_MVREF BDDR2_A[9] ADDR2_A[0] ADDR2_A[1] ADDR2_A[2] ADDR2_A[3] ADDR2_A[4] ADDR2_A[5] ADDR2_A[6] ADDR2_A[7] ADDR2_A[8] ADDR2_A[9] C13 A22 B13 C22 A13 A23 C12 B23 B12 C23 A_DDR2_A0 A_DDR2_A1 A_DDR2_A2 A_DDR2_A3 A_DDR2_A4 A_DDR2_A5 A_DDR2_A6 A_DDR2_A7 A_DDR2_A8 A_DDR2_A9 A_DDR2_A10 A_DDR2_A11 A_DDR2_A12 B_DDR2_A0 B_DDR2_A1 B_DDR2_A2 B_DDR2_A3 B_DDR2_A4 B_DDR2_A5 B_DDR2_A6 B_DDR2_A7 B_DDR2_A8 B_DDR2_A9 B_DDR2_A10 B_DDR2_A11 B_DDR2_A12 AC23 A_DDR2_BA0 A_DDR2_BA1 A_DDR2_BA2 A_DDR2_MCLK A14 D23 /A_DDR2_MCLK A_DDR2_CKE D14 A_DDR2_ODT D13 D12 D22 /A_DDR2_RAS /A_DDR2_CAS /A_DDR2_WE B18 C17 A_DDR2_DQS0 A_DDR2_DQS1 C18 A19 A_DDR2_DQM0 A_DDR2_DQM1 A18 B17 ADDR2_D[0] ADDR2_D[1] ADDR2_D[2] ADDR2_D[3] ADDR2_D[4] ADDR2_D[5] B15 A21 A15 B21 C21 C14 C20 C15 C16 C19 A_DDR2_DQ0 A_DDR2_DQ1 A_DDR2_DQ2 A_DDR2_DQ3 A_DDR2_DQ4 A_DDR2_DQ5 A_DDR2_DQ6 A_DDR2_DQ7 A_DDR2_DQ8 A_DDR2_DQ9 A_DDR2_DQ10 A_DDR2_DQ11 A_DDR2_DQ12 A_DDR2_DQ13 A_DDR2_DQ14 A_DDR2_DQ15 B_DDR2_DQ0 B_DDR2_DQ1 B_DDR2_DQ2 B_DDR2_DQ3 B_DDR2_DQ4 B_DDR2_DQ5 B_DDR2_DQ6 B_DDR2_DQ7 B_DDR2_DQ8 B_DDR2_DQ9 B_DDR2_DQ10 B_DDR2_DQ11 B_DDR2_DQ12 B_DDR2_DQ13 B_DDR2_DQ14 B_DDR2_DQ15 A_DDR2_DQSB0 A_DDR2_DQSB1 B_DDR2_DQSB0 B_DDR2_DQSB1 W25 AE26 W24 AF24 AF25 V26 AE25 W26 Y26 AD25 Y25 BDDR2_D[0] BDDR2_D[1] BDDR2_D[2] BDDR2_D[3] BDDR2_D[4] BDDR2_D[0-15] BDDR2_D[5] BDDR2_D[6] BDDR2_D[7] BDDR2_D[8] BDDR2_D[9] BDDR2_D[10] B_DDR2_DQM0 B_DDR2_DQM1 AB25 AA25 BDDR2_DQS0_N BDDR2_DQS1_N AR10 BDDR2_D[11] BDDR2_D[12] BDDR2_D[9] BDDR2_D[14] AR8 BDDR2_D[4] BDDR2_D[3] BDDR2_D[1] BDDR2_D[6] BDDR2_D[15] BDDR2_D[8] BDDR2_D[10] BDDR2_D[13] AR9 BDDR2_D[7] BDDR2_D[0] BDDR2_D[2] BDDR2_D[5] 56 56 56 AR11 56 TDDR_D[11] TDDR_D[12] TDDR_D[9] TDDR_D[14] TDDR_D[4] TDDR_D[3] TDDR_D[1] TDDR_D[6] TDDR_D[15] TDDR_D[8] TDDR_D[10] TDDR_D[13] TDDR_D[7] TDDR_D[0] TDDR_D[2] TDDR_D[5] VDDL +1.8V_S_DDR VSSDL OPT R51 0 NC1 NC2 NC3 B_DDR2_DQS0 B_DDR2_DQS1 AC25 AC26 BDDR2_DQM0_P BDDR2_DQM1_P /B_DDR2_RAS /B_DDR2_CAS /B_DDR2_WE AB26 AA26 BDDR2_DQS0_P BDDR2_DQS1_P B_DDR2_ODT U25 U24 AB24 /BDDR2_RAS /BDDR2_CAS /BDDR2_WE /B_DDR2_MCLK B_DDR2_CKE U26 BDDR2_ODT B_DDR2_BA0 B_DDR2_BA1 B_DDR2_BA2 B_DDR2_MCLK V24 AB23 /BDDR2_MCLK BDDR2_CKE AC24 AB22 V25 T26 AF26 T25 AF23 T24 AE23 R26 AD22 R25 AC22 R24 BDDR2_A[0] BDDR2_A[1] BDDR2_A[2] BDDR2_A[3] BDDR2_A[4] BDDR2_A[0-12] BDDR2_A[5] BDDR2_A[6] BDDR2_A[7] BDDR2_A[8] BDDR2_A[9] BDDR2_A[11] BDDR2_A[5] BDDR2_A[12] BDDR2_A[7] BDDR2_A[0] BDDR2_A[2] BDDR2_A[4] BDDR2_A[6] BDDR2_A[11] R27 BDDR2_A[8] BDDR2_BA[0] BDDR2_BA[1] BDDR2_BA[2] BDDR2_MCLK R28 56 56 R29 R30 R50 R31 OPT 56 56 AR14 BDDR2_A[3] BDDR2_A[1] BDDR2_A[10] AR12 TDDR_A[0-12] TDDR_A[5] TDDR_A[12] TDDR_A[7] TDDR_A[0] TDDR_A[2] TDDR_A[4] TDDR_A[6] TDDR_A[11] TDDR_A[8] 56 56 0 33 OPT R45 150 56 AR13 TDDR_A[9] TDDR_A[3] TDDR_A[1] TDDR_A[10] TDDR_A[0] TDDR_A[1] TDDR_A[2] TDDR_A[3] TDDR_A[4] TDDR_A[5] TDDR_A[6] TDDR_A[7] TDDR_A[8] TDDR_A[9] TDDR_A[10] TDDR_A[11] TDDR_A[12] A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 VREF
1%
IC100
1%
C43
C1 0.1uF
C22 0.1uF
0.1uF C35
0.1uF C37
0.1uF C38
0.1uF C39
0.1uF
10uF C31
IC2 H5PS5162FFR-S6C
IC2-*1 A3R12E4JFF-G8E
J2
G8 G2 H7 H3 H1 H9 F1 F9 C8 C2 D7 D3 D1 D9 B1 B9
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
G8 G2 H7 H3 H1 H9 F1 F9 C8 C2 D7 D3 D1 D9 B1 B9
J2
VREF
SDDR_A[5] SDDR_A[3] SDDR_A[0] SDDR_A[1] SDDR_A[0-12] SDDR_A[2] SDDR_A[3] SDDR_A[4] SDDR_A[5] SDDR_A[6] SDDR_A[7] SDDR_A[8] SDDR_A[9] SDDR_A[10] SDDR_A[11] SDDR_A[12] SDDR_A[1] SDDR_A[10] 56
AR1
J2
G8 G2 H7 H3 H1 H9 F1 F9 C8 C2 D7 D3 D1 D9 B1 B9
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
TDDR_D[0] TDDR_D[1] TDDR_D[2] TDDR_D[3] TDDR_D[4] TDDR_D[0-15] TDDR_D[5] TDDR_D[6] TDDR_D[7] TDDR_D[8] TDDR_D[9] TDDR_D[10] TDDR_D[11] TDDR_D[12] TDDR_D[13] TDDR_D[14] TDDR_D[15] +1.8V_S_DDR
VREF
J2
G8 G2 H7 H3 H1 H9 F1 F9 C8 C2 D7 D3 D1 D9 B1 B9
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
M8 M3 M7 N2 N8 N3 N7 P2 P8 P3 M2 P7 R2
M8 M3 M7 N2 N8 N3 N7 P2 P8 P3 M2 P7 R2
M8 M3 M7 N2 N8 N3 N7 P2 P8 P3 M2 P7 R2
M8 M3 M7 N2 N8 N3 N7 P2 P8 P3 M2 P7 R2
AR3 SDDR_A[9] SDDR_A[12] SDDR_A[7] SDDR_A[0] SDDR_A[2] SDDR_A[4] SDDR_A[6] SDDR_A[11] SDDR_A[8] R22 56 R21 56 56 AR2 ADDR2_A[9] ADDR2_A[12] ADDR2_A[7] ADDR2_A[0] ADDR2_A[2] ADDR2_A[4] ADDR2_A[6] ADDR2_A[11] ADDR2_A[8]
BA0 BA1
BA0 BA1
CK CK CKE
J8 K8 K2
CK CK CKE
J8 K8 K2
ZENTEL
ODT CS RAS CAS WE K9 L8 K7 L7 K3
K9 L8 K7 L7 K3 A9 C1 VDDQ_10 VDDQ_9 VDDQ_8 VDDQ_7 VDDQ_6 VDDQ_5 VDDQ_4 VDDQ_3 VDDQ_2 VDDQ_1
ZENTEL
C3 C7 C9 E9 G1 G3 G7 G9
LDQS UDQS
F7 B7
L2 VDD5 A1 E1 J9 M9 R1 J8 K8 K2 L3
BA0 BA1
R6
56
BA0 BA1
L2
LDM F3 B3
LDQS UDQS
E8 A8
A3 E3 J3 N1 P9
R7 56 R49 OPT 0 R8 33
L3
A1 E1 J9 M9 R1
UDM
LDQS UDQS
E8 A8
A3 E3 J3 N1 P9
CK CK CKE
CK CK CKE
J8 K8 K2
L1 R3 R7
L1 R3 R7
/SDDR_CK SDDR_CKE
R9 R10
33 56
/ADDR2_MCLK ADDR2_CKE
R32 R33
33 56
/TDDR_MCLK TDDR_CKE
A2 E2 R8
B2 B8 A7 D2 D8 E7 F2 F8 H2
VSSQ_10 VSSQ_9 VSSQ_8 VSSQ_7 VSSQ_6 VSSQ_5 VSSQ_4 VSSQ_3 VSSQ_2 VSSQ_1
A2 E2 R8
B2 B8 A7 D2 D8 E7 F2 F8 H2
VSSQ_10 VSSQ_9 VSSQ_8 VSSQ_7 VSSQ_6 VSSQ_5 VSSQ_4 VSSQ_3 VSSQ_2 VSSQ_1
K9 VDDQ10 VDDQ9 VDDQ8 VDDQ7 VDDQ6 VDDQ5 VDDQ4 VDDQ3 VDDQ2 VDDQ1 A9 C1 C3 C7 C9 E9 G1 G3 G7 G9 F3 B3 F7 B7
ODT CS RAS CAS WE /SDDR_RAS /SDDR_CAS /SDDR_WE LDQS UDQS SDDR_DQS0_P SDDR_DQS1_P LDM UDM SDDR_DQM0_P SDDR_DQM1_P R17 R18 56 56 ADDR2_DQM0_P ADDR2_DQM1_P R40 R41 56 56 TDDR_DQM0_P TDDR_DQM1_P R15 R16 56 56 ADDR2_DQS0_P ADDR2_DQS1_P R38 R39 56 56 TDDR_DQS0_P TDDR_DQS1_P R12 R13 R14 56 56 56 /ADDR2_RAS /ADDR2_CAS /ADDR2_WE SDDR_ODT R11 56 ADDR2_ODT R34 R35 R36 R37 56 56 56 56 /TDDR_RAS /TDDR_CAS /TDDR_WE
K9 L8 K7 L7 K3
VSSDL
J7
VDDL
HYNIX
L8 K7 L7 K3
HYNIX
A9 C1 C3 C7 C9 E9 G1 G3 G7 G9
VDDQ10 VDDQ9 VDDQ8 VDDQ7 VDDQ6 VDDQ5 VDDQ4 VDDQ3 VDDQ2 VDDQ1
VSSDL
J7
J1
H8
VDDL
J1
H8
LDQS UDQS
F7 B7
LDM UDM
F3 B3
A3 E3 J3 N1 P9
E8 A8
LDQS UDQS SDDR_DQS0_N SDDR_DQS1_N R19 R20 SDDR_D[11] OPT R48 0 SDDR_D[12] SDDR_D[9] SDDR_D[14] SDDR_D[4] SDDR_D[3] SDDR_D[1] SDDR_D[6] 56 AR5 56 AR6 56 56 AR4 ADDR2_D[11] ADDR2_D[12] ADDR2_D[9] ADDR2_D[14] ADDR2_D[4] ADDR2_D[0-15] ADDR2_D[3] ADDR2_D[1] ADDR2_D[6] ADDR2_D[15] ADDR2_D[8] ADDR2_D[10] 56 AR7 SDDR_D[7] SDDR_D[0] SDDR_D[2] SDDR_D[5] 56 ADDR2_D[7] ADDR2_D[0] ADDR2_D[2] ADDR2_D[5] ADDR2_D[13] ADDR2_DQS0_N ADDR2_DQS1_N R42 R43 56 56 TDDR_DQS0_N TDDR_DQS1_N
LDQS UDQS
E8 A8
A3 E3 J3 N1 P9
L1 R3 R7
L1 R3 R7
VSSQ10 VSSQ9 VSSQ8 VSSQ7 VSSQ6 VSSQ5 VSSQ4 VSSQ3 VSSQ2 VSSQ1
B2 B8 A7 D2 D8 E7 F2 F8 H2 H8
A2 E2 R8
A2 E2 R8
B2 B8 A7 D2 D8 E7 F2 F8 H2
VSSQ10 VSSQ9 VSSQ8 VSSQ7 VSSQ6 VSSQ5 VSSQ4 VSSQ3 VSSQ2 VSSQ1
J7
VSSDL +1.8V_S_DDR
J7
ADDR2_D[10] B16 ADDR2_D[11] B20 ADDR2_D[12] A20 ADDR2_D[13] A16 ADDR2_D[14] B19 ADDR2_D[15] A17
J1
VDDL
AE24 BDDR2_D[11] AD26 BDDR2_D[12] Y24 BDDR2_D[13] AD24 BDDR2_D[14] AA24 BDDR2_D[15]
J1
H8
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
DDR
09.09.03 21
+3.3V_Normal
+3.3V_Normal
R105 4.7K
+3.3V_Normal
CS#
VCC
IC101 MX25L3205DM2I-12G
R103 10K
SPI_DO 001:AR36
SO
HOLD#
R101
WP#
SCLK
SPI_CK 001:AR35
GND C
SI
SPI_DI 001:AR36
Flash_WP_1
001:AR30
R102 OPT0
B Q100 KRC103S
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
SERIAL FLASH
09.09.03 21
TU5001 TDVJ-H001F
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 SHIELD ANT_PWR[OPT] BST_CNTL +B NC[RF_AGC] AS SCL SDA NC(IF_TP) SIF
C5012 47pF 50V C5013 47pF 50V R5001 0 OPT C5001 100pF 50V C5003 0.1uF 16V R5018 3.3K 100 R5015 C5025 R5020 3.3K FE_TUNER_SCL 100 R5016 FE_TUNER_SDA R5005 2.2K OPT 100pF 50V R5025 4.7K R5002 0 OPT
+5V_TU
+5V_TU
+3.3V_TU
OPT
R5032 82 FE_SIF E
B C Q5004
ISA1530AC1
+5V_TU
0.1uF
SIFMO
R5006 47 OPT C5005 OPT TU_CVBS_BUFER R5030 220 2012 R5031 220 2012 TU_CVBS_BUFER 1/16W 5% FE_VMAIN
R5004 0
R5026 1K OPT
TU_CVBS_BUFER
E L5000 INNOTEK
+1.26V
+3.3V_TU
+3.3V_TU
R5011 100K C5010 0.1uF 16V
TU_CVBS_BUFER R5027 1K OPT R9823 0 TUNER_RESET R9824 0 VSB_RESET OPT R5000 10K OPT C5000 0.047uF 50V R5012 0 TU_CVBS_BYPASS
R5009 100
R5022 1K
IF_AGC
should be guarded by ground
DIF_1 DIF_2
R5035 0
R5034
VCOMO
IF_N_MSTAR IF_P_MSTAR
MStar Option
Close to the tuner
+5V_TU
+5V_Normal
5V_TU_Normal 200mA L5002 BLM18PG121SN1D C5018 22uF 16V OPT C5019 22uF 16V C5021 0.1uF 16V C5023 0.1uF 16V
+3.3V_TU
IC5001 AP1117EG-13
+1.26V
IN
OUT
ADJ/GND R5008 120 C5002 22uF 10V 1 R5033 C5017 22uF 16V OPT C5020 22uF 16V C5029 10uF 10V C5028 0.1uF 16V 60mA
+3.3V_TU
+3.3V_Normal
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
LD350
ATSC_CAN TUNER
09.09.03 26
VSB B+ BLOCK
+5V_Normal +3.3V_PVSB OPT IC1001 SC156515M-1.8TR
+3.3V_TU
001:AR30;007:AH18 POWER_ON/OFF2_2
IC1000 SC4215ISTRT
L1005 500 R1035 100 OPT R1036 20K NC_1 GND R1011 20K R1012 10K R2 +1.2V_PVSB
L1000 MLB-201209-0120P-N2 OPT R1001 4.7K OPT OPT R1002 1K C1002 100uF 16V OPT C1003 0.1uF 50V OPT
VIN
EN
ADJ
EN
1 3 GND
ADJ
VIN OPT C1018 100uF 16V C1020 0.1uF 50V C1077 2.2uF 16V C1078 C1076 2.2uF 1uF 16V 16V
VO
R1
VSB_RESET
+1.2V_DVDD_PVSB
R1073 0
48
47
46
45
44
43
42
41
40
39
38
VDD33 OPM
37
NRST
VCCAAD10A
XM
SLIM_SCAN
VSSAD10
XTALI
XTALO
VSS33
VDD
VSS
1 IF_P_MSTAR IF_N_MSTAR R1061 100 R1062 100 0.01uF 0.01uF 0.1uF C1069 C1070 C1068 R1064 100 R1065 R1066 R1067 IF_AGC C1066 0.1uF R1060 1K C1067 0.1uF R1063 1K OPT 0 OPT OPT 2 3 4 5 6 7 8 9 10 11 12
36
PLLAVSS
35
PLLAVDD
34
VSS33
33
VSSAAD10A I2CSEL ANTCON VDD I2CRPT_SCL I2CRPT_SDA IF OUT TPDATA[1] TPDATA[2] TPDATA[3] TPDATA[4] TPDATA[5] TPDATA[6] TPDATA[0] TPDATA[7] TPVALID RF OUT TPERR VDD33
IC1004 LGDT3305
VSS
32
VDD
31
VSS
30
SCL
22R1077 FE_DEMOD_SCL 22 R1078 FE_DEMOD_SDA C1074 22pF 50V OPT C1075 22pF 50V OPT AR1079 100 1/16W TS_SYNC TS_CLK TS_VALID
29
VDD33
28
SDA
27
NIRQ
26
TPSOP
25
TPCLK
13
14
15
16
17
18
VSS33
R1076 OPT 0
19
20
21
22
23
+3.3V_DVDD_PVSB
470 R1069
JTAG
TS_VALID TS_SYNC TS_CLK
LD1000
100
AR1071 100
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
VSB_DEMOD
24
LD350 VSB_DEMOD
09.09.03 28
+3.3V_Normal
R9802 10K
AV_CVBS_DET
[YL1]O-SPRING
AV_CVBS_IN D9809 30V R9812 75
D9800 5.6V
[YL1]E-LUG [RD2]E-LUG
D9805 5.6V
R9811 470K
R9819 12K
COMP1_L_IN D9808 5.6V R9814 470K C9808 1000pF 50V R9822 12K
[RD2]E-LUG-S [BL2]O-SPRING
D9803 30V
COMP1_PB
+3.3V_Normal
D9804 30V
R9809 75
D9801 5.6V
[GN2]E-LUG
30V
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
LD350 COMPONENT&AV
09.09.03 31
PANEL_VCC
C805 0.1uF
TXA1-[9] TXA1+[8]
0 0
R809 HD R810 HD R811 HD R812 HD R813 HD R814 HD R815 HD R816 HD R817 HD R818 HD
LVDS_TXA3+ LVDS_TXA3-
TXA2-[7] +3.3V_Normal TXA2+[6] R822 R820 1K 22"CMO 5.1K CMO&Sharp LVDS_SEL JEIDA R823 10K AUO26"~32" LVDS_TXA3+ LVDS_TXA3TXA4-[1] LVDS_TXAC+ LVDS_TXACTXA4+[0] VESA(NS) CMO 22" LOW HIGH AUO 26"/32" Sharp 26"/32" HIGH LOW/OPEN LOW(GND) HIGH/OPEN(Defult) TXA3-[3] TXA3+[2] TXAC-[5] TXAC+[4]
0 0
LVDS_TXAC+ LVDS_TXAC-
0 0
LVDS_TXA2+ LVDS_TXA2-
0 0
LVDS_TXA1+ LVDS_TXA1-
0 0
LVDS_TXA0+ LVDS_TXA0-
LVDS_TXA2+ LVDS_TXA2-
LVDS_TXA1+ LVDS_TXA1-
OPC_OUT
PANEL_VCC
C804 1000pF
C806 0.1uF
HD_60Hz_Normal
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
LD350 LVDS
09.09.03 32
IC601
+3.3V_Normal
+1.8V_AMP
3 2
OUTPUT
GND
SPK_L+ AMP_VCC R625 3.3 C643 0.01uF D602 100V OPT D601 100V OPT R613 5.6 C629 1000pF 50V C630 1000pF 50V R614 5.6 C618 22000pF 50V PGND1A_2 PGND1A_1 PVDD1A_2 PVDD1A_1 PVDD1B_2 PVDD1B_1 PGND1B_2 PGND1B_1 C619 1uF 16V L606 AD-9060 EAP61008401 2S 2F C633 0.47uF 50V 1S 1F C636 0.1uF 50V R618 4.7K C639 0.01uF 50V R621 3.3 R622 3.3 C640 0.01uF 50V
006:AH11
R617 4.7K
SPEAKER_L
C602 68uF
MLB-201209-0120P-N2
SPK_L- 006:AH10
BST1B 44
R601 100 001:AB21 AMP_RST C606 1000pF 50V 001:W26 AUDIO_MASTER_CLK +1.8V_AMP +1.8V_AMP MLB-201209-0120P-N2 MLB-201209-0120P-N2
56
55
54
53
52
51 50
49
48
47
46
45
BST1A VDR1A RESET AD DVSS_1 VSS_IO CLK_I VDD_IO DGND_PLL AGND_PLL LFM AVDD_PLL DVDD_PLL TEST0
43
VDR1B
42 41 40 39 38 37 36 35 34 33 32 31 30 29
NC VDR2A BST2A
C622 16V1uF
C624 22000pF 50V D603 100V OPT R615 5.6 C631 1000pF 50V C632 1000pF 50V R616 5.6 L607 AD-9060 EAP61008401 2S 2F C641 C634 0.47uF 50V C637 0.1uF 50V R619 4.7K 0.01uF 50V R623 3.3 R624 C638 0.1uF 50V R620 4.7K 3.3 C642 0.01uF 50V
SPK_R+ 006:AH10
PGND2A_2 PGND2A_1 OUT2A_2 OUT2A_1 PVDD2A_2 PVDD2A_1 PVDD2B_2 PVDD2B_1 OUT2B_2 OUT2B_1 PGND2B_2
C608 0.1uF L604 R600 0 C604 100pF 50V C607 1000pF 50V R602 3.3K
SPEAKER_R
1F
L603
SPK_R-
006:AH9
AMP_VCC R626 3.3 C626 0.01uF 50V C623 22000pF 50V C627 0.1uF 50V C645 0.1uF 50V C644 0.01uF 50V
DVSS_2
SDATA
FAULT
VDR2B
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
DVDD
WCK
BCK
SDA
SCL
+1.8V_AMP
PGND2B_1
Mstar Application
C610 10uF 10V
C628 68uF
100 100 100 100 100 C609 33pF 50V C612 33pF 50V C616 33pF 50V OPT
R627
POWER_DET
HP_DET
P600 WAFER-ANGLE
L608 120-ohm 006:AJ22 SPK_L+ L609 120-ohm 4
R610
006:AJ20
SPK_LL611 120-ohm
006:AJ18
006:AJ16
SPK_R-
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
AMP
09.02.19 3 14
No
Check Power connector
ok
Check Fuse.
ok
Replace Power board.
ok
Check Micom Voltage IC400 pin 3 : +3.3V
No
Replace IC400
ok No
Check X100 clock 12MHz Replace X100.
ok
Check P403 PWR_ON. 1pin : 3.3V
No
Re-download software.
No
Replace Mstar(IC100) or Main board
ok
Check Multi Voltage P403 2 pin : 24V , 17 pin : *12V
No
Replace Power Board
*12V Voltage is dependent on Model 26/32LD350 => 12V 19/22LD350 => 15V
ok
Check Inverter Control & Error Out P403 18 pin : High P403 24 pin : low
No
Check Power Board or Module
ok
Check IC403/5/7 Output Voltage IC403 : 1.26V IC405 : 3.3V IC407 : 1.8V
No
OK
Replace IC403/5/7
ok
Check LVDS Power Voltage Q409 : 12V
No
Replace Q409
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board
ok
Change Module
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
2. Digital TV Video
Check RF Cable & Signal
ok
Check Tuner 5V Power L5004
No
No
Replace IC401
ok No
Check Tuner 3.3V Power L5003 Replace L5003
ok
Replace L5004
ok
Check Tuner 1.2V Power IC5001 2 pin : 1.2V
No
Replace IC5001.
ok
Check IF_P/N Signal TU5001 17/18 Pin
No
Bad Tuner. Replace Tuner.
ok No
Check IC1004(LGDT) VCC Check VCCIN/OUT IC1001,IC100
No
Replace IC1001,IC100
ok
Check Demodulator Input Clock(X1005-25Mhz)
No
Replace X1005
ok
Check IC1004(LGDT) Output - AR1070, AR1071
No
Replace IC1004
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
3. Analog TV Video
Check RF Cable & Signal
ok
Check Tuner 5V Power L5004
No
No
Check IC401 Replace IC401
ok No
Check Tuner 3.3V Power L5003 Replace L5003
ok
Replace L5004
ok
Check Tuner 1.2V Power IC5001 2 pin : 1.2V
No
Replace IC5001.
ok
Check CVBS Signal TU5001 11 Pin
No
Bad Tuner. Replace Tuner.
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
4. AV Video
Check input signal format. Is it supported?
ok
Check AV Cable for damage for damage or open conductor
ok
Check JK9800 (*JK3302) CVBS Signal Line R137 (*R114)
No
Replace Jack
ok No
Check CVBS_DET Signal Replace R9802 or R9803
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board.
5. Component Video
Check input signal format. Is it supported?
ok
Check Component Cable for damage or open conductor.
ok
Check JK9800 Y/PB/PR signal Line (R121/120/122)
No
Replace Jack
ok No
Check COMP_DET Signal Replace R9800,R9801
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
6. RGB Video
Check input signal format. Is it supported?
ok
Check RGB Cable conductors for damage or open conductor
ok
Check EDID & EEPROM IC1105 I2C Signal R1141, R1143(SDA,SCL)
No
Replace the defective IC or re-download EDID data
ok
Check JK1104 H/V_Sync/R/G/B Signal Line (R146/149/127/128/129)
No
Replace Jack
ok No
Check DSUB_DET Replace R1146 or R1147
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
7. HDMI Video
Check input signal format. Is it supported?
ok
Check HDMI Cable conductors for damage or open conductor.
ok
Check EDID & EEPROM IC7701 (*IC7702) I2C Signal
No
Replace the defective IC or re-download EDID data
ok No
Check JK7700, JK7702 Replace Jack * JK7702 is Side HDMI supported model 26/32LD350 models
ok No
Check HDMI_DET(HPD) Replace R7703,R7705,R7731,R7732
ok
Check HDCP Key NVRAM(IC105) Power & I2C Signal
No
Replace the defective IC.
ok No
Check HDMI Signal Check other set If no problem, check signal line
No
Replace Main Board
ok No
Check Mstar LVDS Output Replace Mstar(IC100) or Main Board.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
Off
Toggle the Menu
On
Check AMP IC(IC600) Power *20V, 3.3V, 1.8V.
No
Check Regulator IC601
*20V Voltage is dependent on Model 26/32LD350 => 24V 19/22LD350 => 15V
ok No
Check Mstar AUDIO_MASTER_CLK R603 Replace Mstar(IC100) or Main Board.
ok
Check AMP I2C Line R607, R608
No
Check signal line. Or replace Mstar(IC100)
ok
Check Mstar I2S Output R604, R605, R606
No
Check signal line. Or replace Mstar(IC100)
ok
Check Output Signal P600 1, 2, 3, 4 pin.
No
ok No
Check Connector & P600 Replace connector if found to be damaged.
ok
Check speaker resistance and connector damage.
No
Replace speaker.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
9. Digital TV Audio
Check RF Cable & Signal
ok
Check Tuner 5V Power L5004
No
No
Check IC401 Replace IC401
ok No
Check Tuner 3.3V Power L5003 Replace L5003
ok
Replace L5004
ok
Check Tuner 1.2V Power IC5001 2 pin :1.2V
No
Replace IC5001.
ok
Check IF_P/N Signal TU5001 17/18 Pin
No
Bad Tuner. Replace Tuner.
ok No
Check IC1004(LGDT) VCC Check VCCIN/OUT IC1001,IC100
No
Replace IC1001,IC100
ok No
Replace X1005
ok
Check IC1004(LGDT) Output - AR1070, AR1071
No
Replace IC1004
ok
Follow procedure 8. All source audio trouble shooting guide.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
ok
Check Tuner 5V Power L5004
No
No
Check IC401 Replace IC401
ok No
Check Tuner 3.3V Power L5003 Replace L5003
ok
Replace L5004
ok
Check Tuner 1.26V Power IC5001 2 pin : 3.3V
No
Replace IC5001.
ok
Check SIF Signal & Buffer signal TU5001 11 Pin / R5032
No
Replace Tuner. Or Replace Q5004
ok
Follow procedure 8. All source audio trouble shooting guide.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
11. AV Audio
Check AV Cable for damage for damage or open conductor
ok
Check JK9800, *JK3302 & Signal Line
No
Replace Jack
ok
Follow procedure 8. All source audio trouble shooting guide.
ok No
Check JK9800 & Signal Line Replace Jack
ok
Follow procedure 8. All source audio trouble shooting guide.
ok No
Check JK1104 & Signal Line Replace Jack
ok
Follow procedure 8. All source audio trouble shooting guide.
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
IF +/RF IF AGC
TS_Sync
LVDS
LCD Module
(HD, 60Hz) LGD or OS
TDVJ - H031F
SIF TU_CVBS
LGDT3305
TS_Clk TS_Data[0-7]
Side AV2 AV1 Component 1 D-sub RGB Audio L/R (for RGB) HDMI 1 JACK PACK HDMI 4 (side HDMI)
CVBS, L/R
RGB/H/V
PCM_A [0 7] CS ,RE,WE
Audio L/R
MSD3368GV
SCL, SDA_3.3V
NVRAM HPl AMP TPA6110A2D Digital AMP NTP3100L JTAG Reset IC (MAX809RTR)
Audio L/R
H/P
I2S
SPDIF CLK,TDI,TDO,MS,RST
MAX3232
RX/TX
Reset
Reset Switch
USB
X-tal
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
RF
IF +/IF AGC
TS_Sync/VLD
TDVJ - H031F
SIF TU_CVBS
LGDT3305
TS_Clk TS_Data[0-7]
MSD3368GV
RXB2P RXB2N
AV_CVBS_IN SIDEAV_CVBS_IN
CVBS3 CVBS2
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
RF
IF +/IF AGC
TS_Sync/VLD
TDVJ - H031F
SIF TU_CVBS
LGDT3305
TS_Clk TS_Data[0-7]
I2S_MASTER_CLK I2S_LCRK
I2S_OUT_WS
AV_L_IN AV_R_IN
I2S_SCK
I2S_OUT_BCK I2S_OUT_SD
COMP1_L_IN COMP1_R_IN
I2S_LCRH
MSD3368GV
HP_ROUT
HP/ R HP/ L
SIDEAV_L_IN SIDEAV_R_IN
HP_LOUT
HP AMP TPA6110A2D
H/P
PC_L_IN PC_R_IN
+3.3V
SPDIF_OUT
SPDIF_OUT 1K
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
PCM_A[0-7]
MSD3368GV
/PF_OE /PF_CE0 /PF_CE1 PF_ALE
ALE
PF_ALE
/PF_WE
WE /PF_WE
PF WP
WP PF_AD15
HWRESET
Reset IC (MAX809RTR)
Reset Switch
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
3.3k ohm
4.7k ohm
3.3k ohm
4.7k ohm
OPT
1.2k ohm 1.2k ohm
FE_TUNER_SCL/SDA
SCL1/SDA1
1.2k ohm
1.2k ohm
33 ohm 33 ohm
EEPROM_SCL/SDA
0 ohm 0 ohm
22 ohm
MSD3368GV
22 ohm 22 ohm
SCL0/SDA0
22 ohm
FE_DEMOD_SCL/SDA
LGDT 3305
+5V_Gen.
4.7k ohm
4.7k ohm
RGB_DDC_SCL/SDA
22 ohm 2 ohm
DDCA_CK DDCA_DA
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
DSUB_DET
ET_RXD1
GPIO 88
5V_HDMI_1
GPIO 86
GPIO 98 SAR3
(Stand-by GPIO)
AMP_MUTE
5V_HDMI_4
GPIO 84
MSD3368GV
UART_RX2 UART_TX2
DBG_RX DBG_TX
RS232C (MAX3232CDR)
KEY1 KEY2
SAR0 SAR1
IR
IRIN
ET_MDIO
VSB_RESET
VSB IC (LGDT3305)
USB_DM2 USB_DP2
USB_DM USB_DP
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
1 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
Pin Num ber HWRESET UART2_TX_SCKM UART2_RX/SDAM DDCR_DA DDCR_CK DDCA_CLK DDCA_DA UART_RX2 UART_TX2 PWM0 PWM1 PWM2 PWM3 SAR0 SAR1 SAR2 SAR3 IRIN GPIO44 GPIO96 GPIO88 GPIO90/I2S_OUT_MUTE GPIO91 GPIO97 GPIO98 GPIO99 GPIO103/I2S_OUT_SD3 GPIO102 GPIO68 GPIO67 ET_COL ET_MDIO ET_MDC ET_TX_EN ET_RXD1 ET_RXD0 ET_TX_CLK ET_TXD1 ET_TXD0
Pin Nam e D4 F8 D11 AB21 AC21 J1 J2 W5 V5 AB13 AB12 AD12 AA13 A4 B4 F4 E4 C4 AC11 D9 D10 D7 E11 E8 E10 D6 D5 C5 B8 A7 A11 B9 A10 B10 C9 C11 A9 B11 C10
GP1.5 Signal Nam e(Ver3) S5/ S6_Res et EEPROM _SCL EEPROM _SDA SDA0 SCL0 ISP_RXD ISP_TXD DBG_RX DBG_TX PWM 0 PWM 1 PWM 2 PWM 3 KEY1 KEY2 LED_R/ Buz z SB_M UTE IR OPT OPT AM P_RST HD&19/ 22LH&19LU,(FHD) M oving LED,(Normal LED) ERROR_OUT NTP_M UTE +3.3V_ST,(OPT) BIT_SEL OLP HP_M UTE USB_CTL SIDE_HP_M UTE VSB_RESET, EEPROM _WP DSUB_DET COM P1_DET HP_DET SIDEAV_DET AV_CVBS_DET
Pin Num ber TS1_CLK TS1_VLD TS1_SYNC TS1_D0 TS0_CLK TS0_VLD TS0_SYNC GPIO43/PCM2_IRQA_N GPIO42/PCM2_CE_N UART1_TX/GPIO87 UART1_RX/GPIO86 UART2_TX/GPIO85 UART2_RX/GPIO84 GPIO79/LVSYNC2/TX1 LVSYNC/GPIO133 LHSYNC2/I2S_OUT_MUTE/RX1 GPIO62/PCM2_CD_N/TX1 GPIO60/PCM2_RESET/RX1 GPIO132/LHSYNC/SPI_WPn GPIO130/LCK GPIO131/LDE/SPI_WPn1 GPIO_PM6/INT2/GPIO140 GPIO_PM5/INT1/GPIO139 GPIO_PM4/GPIO138 GPIO_PM3/GPIO137 GPIO_PM2/GPIO136 GPIO_PM1/GPIO135 GPIO_PM0/GPIO134 USB_DP_2 USB_DM_2 USB_DM_1 USB_DP_1 SPI_CK /SPI_CS SPI_DO SPI_DI
Pin Nam e AA19 AC19 AA20 AB19 AB4 AD5 AC4 AF10 AF5 B6 A6 F10 F9 C6 AC18 E7 AA17 AA18 AF11 AB17 AC17 H6 G6 F6 H5 G5 F5 E5 AB10 AC10 A5 B5 AD11 AE12 AF12 AE11
GP1.5 Signal Nam e(Ver3) OPT OPT OPT OPT TS_CLK TS_VALID TS_SYNC OPT TUNER RESET 5V_HDM I_DET_2 5V_HDM I_DET_1 USB_OCD 5V_HDM I_DET_4 FE_TUNER_SDA OPC_EN FE_TUNER_SCL SCL1 SDA1 Flas h_WP_1 Pow er on/ off2-2 Pow er on/ off2-1 POWER_DET DBG_RX POWER_ON/ OFF1 PANEL_CTL INV_CTL DBG_TX RL_ON . . SIDE_USB_DM SIDE_USB_DP SPI_CK SPI_CS SPI_DO SPI_DI
E6 A3 B3
. . .
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
Panel_Vcc(+5V)
LVA0 P/M LVA1 P/M LVA2 P/M LVA3 P/M LVA4 P/M
MSD3368GV
LVDS TXA0+/LVDS TXA1+/LVDS TXA2+/LVDS TXAC+/LVDS TXA3+/-
Panel_Vcc(+12V)
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
+3.3V_ST
P403 (#9~12),
+3.5V_ST
L404
IC103 MAX810RTR (Reset) IC409 NL17SZ08DFT2G (OPT) Q7703 FDV301N (FET) IC1201 MAX3232CDR (RS-232C) IC1201 MAX3232CDR (RS-232C) IC403 MP2212DN (DCDC)3A IC407 MP2212DN (DCDC)3A
+3.3V_AVDD_MPLL
S5/S6 Reset
Power_DET
CEC_REMOTE
+1.26V_VDDC
+1.8V_DDR
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
POWER POWER Block Block (+24V (+24V & & 12V 12V &+12V/+15V)_For &+12V/+15V)_For 26/32 26/32
+24V
P403 (#2,4,3)
+24V/+15V
L407
IC408 NCP803SN293
AMP_VCC
Power_DET
+24V
R469
IC600 NTP-3100L
+12V
P403 (#17,19,21)
+12V
L402
R477
+12V/+15V
Q409 AO3407A (FET) IC401 MP8706EN (DCDC)3A IC405 AOZ1073AIL (DCDC)3A IC409 AOZ1073AIL (DCDC)3A IC408 NCP803SN293
PANEL_VCC
P800
+5V_USB
+3.3V_Normal
+5V_Normal
Power_DET
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
+3.3V_Nor mal
+3.3V_Normal
L407
IC104 AT24C512BW EEPROM IC105 CAT24WC08W HDCP EEPROM IC102 HY27US08121B Flash IC100 MSD3159GV Main_SOC(S5) IC101 MX25L3205DM2I Serial Flash IC1104 NL17SZ00DFT2G SPDIF IC600 NTP3100L AMP IC601 AZ1117H-1.8TRE1 LDO
+3.3V_TU
L5003
+1.8V_AMP
IC600 NTP-3100L
+1.26V
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
+5V_Norm al
+5V_Normal
L407
For HDMI
For RGB PC
+1.2V_PVSB
+3.3V_TU
L1005
+5V_USB
+5V_USB L5003
+5V_TU
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
+3.5V_ST
+3.3V_ST
P402 (#5,6)
L404
IC103 MAX810RTR (Reset) IC409 NL17SZ08DFT2G (OPT) Q7703 FDV301N (FET) IC1201 MAX3232CDR (RS-232C) IC1201 MAX3232CDR (RS-232C) IC403 MP2212DN (DCDC)3A IC407 MP2212DN (DCDC)3A
+3.3V_AVDD_MPLL
S5/S6 Reset
Power_DET
CEC_REMOTE
+1.26V_VDDC
+1.8V_DDR
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
POWER POWER Block Block (+15V (+15V & & +12V/+15V)_For +12V/+15V)_For 19/22 19/22
+15V
+15V
P402(#1,2)
L407
IC408 NCP803SN293
Power_DET
AMP_VCC
IC600 NTP-3100L
R476
+12V/+15V
IC401 MP8706EN (DCDC)3A IC405 AOZ1073AIL (DCDC)3A IC409 AOZ1073AIL (DCDC)3A IC408 NCP803SN293
+5V_USB
+3.3V_Normal
+5V_Normal
Power_DET
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
+3.3V_Nor mal
+3.3V_Normal
L407
IC104 AT24C512BW EEPROM IC105 CAT24WC08W HDCP EEPROM IC102 HY27US08121B Flash IC100 MSD3159GV Main_SOC(S5) IC101 MX25L3205DM2I Serial Flash IC1104 NL17SZ00DFT2G SPDIF IC600 NTP3100L AMP IC601 AZ1117H-1.8TRE1 LDO
+3.3V_TU
L5003
+1.8V_AMP
IC600 NTP-3100L
+1.26V
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes
+5V_Norm al
+5V_Normal
L407
Q409 AO3407A (FET) IC7700~7702 AT24C02BN EDID EEPROM IC1105 AT24C02BN EDID EEPROM
PANEL_VCC
P801,P802
For HDMI
For RGB PC
+1.2V_PVSB
+3.3V_TU
L1005
+5V_USB
+5V_USB L5003
+5V_TU
Copyright 2010 LG Electronics. Inc. All right reserved. Only for training and service purposes