Documente Academic
Documente Profesional
Documente Cultură
IKCS17F60F2A IKCS17F60F2C
http://www.infineon.com/cipos
N e v e r
s t o p
t h i n k i n g .
2009-04 1.1 Subjects (major changes since last revision) Added UL certification Change VIT,HYS
Rev.2
Authors: W. Frank, H. Rettinger Edition 2008-09 Published by Infineon Technologies AG 85579 Neubiberg, Germany Infineon Technologies AG 4/6/09. All Rights Reserved. Attention please! The information given in this data sheet shall in no event be regarded as a guarantee of conditions or characteristics (Beschaffenheitsgarantie). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office or representatives (http://www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office or representatives. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. TRENCHSTOP is a registered trademark of Infineon Technologies AG. CIPOS, CoolMOS, CoolSET, DuoPack and thinQ! are trademarks of Infineon Technologies AG.
Data Sheet
2/18
CIPOS Control integrated Power System..................................................................................................4 Features ........................................................................................................................................................4 Target Applications .....................................................................................................................................4 Description ...................................................................................................................................................4 System Configuration .................................................................................................................................4 Internal Electrical Schematic...........................................................................................................................5 Pin Assignment.................................................................................................................................................6 Pin Description ............................................................................................................................................6 /HIN1,2,3 and /LIN1,2,3 (Low side and high side control pins, Pin 15 - 20) .............................................. 6 /FLT-TEMP (temperature NTC, Pin 24) ..................................................................................................... 7 ITRIP (Over-current detection function, Pin 21) ......................................................................................... 7 VDD, VSS (control side supply and reference, Pin 22, 23)........................................................................ 7 VB1,2,3 and VS1,2,3 (High side supplies, Pin 1, 2, 4, 5, 7, 8)................................................................... 7 VRU, VRV, VRW (low side emitter, Pin 12, 13, 14) ................................................................................... 7 V+ (positive bus input voltage, Pin 10)....................................................................................................... 7 Absolute Maximum Ratings ............................................................................................................................8 Module Section ............................................................................................................................................8 IGBT and Diode Section .............................................................................................................................8 Control Section ............................................................................................................................................9 Recommended Operation Conditions............................................................................................................9 Static Parameters ...........................................................................................................................................10 Dynamic Parameters ......................................................................................................................................11 Integrated Components .................................................................................................................................12 Typical Application.........................................................................................................................................12 Characteristics................................................................................................................................................13 Test Circuits and Parameter Definition ........................................................................................................15 Package Outline IKCS17F60F2A ...................................................................................................................17 Package Outline IKCS17F60F2C ...................................................................................................................18
Data Sheet
3/18
Description
The CIPOS module family offers the chance for integrating various power and control components to increase reliability, optimize PCB size and system costs. This SIL-IPM is designed to control AC motors in variable speed drives for applications like air conditioning, compressors and washing machines. The package concept is specially adapted to power applications, which need extremely good thermal conduction and electrical isolation, but also EMI-save control and overload protection. The features of Infineon TrenchStop IGBTs and antiparallel diodes are combined with a new optimized Infineon SOI gate driver for excellent electrical performance. The product provides a FAULT signal, which is significantly simplifying the system.
System Configuration
3 halfbridges with TrenchStop IGBT & FWdiodes 3 SOI gate driver Bootstrap diodes for high side supply Integrated 100nF bootstrap capacitance Temperature sensor, passive components for adaptions Isolated heatsink Creepage distance typ. 3.2mm
Target Applications
Washing machines Consumer Fans and Consumer Compressors
Certification
UL 1577 (UL file E314539)
Data Sheet
V+ (10)
Tr1, U-HS D1 Cge = 390 pF Cge1 Tr3, V-HS D3 Cge3 Tr5, W-HS D5 Cge5
VRU (12) VRV (13) VRW (14) U, VS1 (8) V, VS2 (5) W, VS3 (2)
RH1 RL1 RH2 RL2 RH3 RL3
Rbs
VDD (22) /HIN1 (15) /HIN2 (16) /HIN3 (17) /LIN1 (18) /LIN2 (19) /LIN3 (20) ITRIP (21) /FLTTEMP (24) VSS (23)
C1 Dz
Driver-IC
Data Sheet
5/18
Pin Description
/HIN1,2,3 and /LIN1,2,3 (Low side and high side control pins, Pin 15 - 20) These pins are active low and they are responsible for the control of the integrated IGBT The Schmitt-trigger input threshold of them are such to guarantee LSTTL and CMOS compatibility
down to 3.3V controller outputs. The maximum voltage at these pins is 6V and therefore fully compliant to 3.3V-microcontrollers. Pull-up resistor of about 75 k is internally provided to pre-bias inputs during supply start-up and a zener clamp is provided for pin protection purposes. Input schmitt-trigger and noise filter provide beneficial noise rejection to short input pulses. It is recommended for proper work of CIPOS not to provide an input pulse-width and PWM deadtimes lower than 1us. The integrated gate drive provides additionally a shoot through prevention capability which avoids the simultaneous on-state of two gate drivers of the same leg (i.e. HO1 and LO1, HO2 and LO2, HO3 and LO3).
Figure 3: Internal Circuit at pin TEMP The same pin indicates a module failure in case of under voltage at pin VDD or in case of triggered over current detection at ITRIP. A pull-up resistor is externally required to bias the NTC. No temperature information is available during fault. ITRIP (Over-current detection function, Pin 21) CIPOS provides an over-current detection function by connecting the ITRIP input with the motor current feedback. The ITRIP comparator threshold (typ 0.46V) is referenced to VSS ground. A input noise filter (typ: tITRIPMIN = 220ns) prevents the driver to detect false over-current events. Over-current detection generates a hard shut down of all outputs of the gate driver after the shutdown propagation delay of typically 900ns. The fault-clear time is set to typically to 4.7ms. VDD, VSS (control side supply and reference, Pin 22, 23) VDD is the low side supply and it provides power both to input logic and to low side output power stage. Input logic is referenced to VSS ground as well as the under-voltage detection circuit. The under-voltage circuit enables the device to operate at power on when a supply voltage of at least a typical voltage of VDDUV+ = 12.1 V is at least present. Figure 4: Input filter timing diagram integrated bootstrap capacitors of 100 nF at each floating supply, which are located very close to the gate drive circuit. The under-voltage detection operates with a rising supply threshold of typical VBSUV+ = 12.1 V and a falling threshold of VDDUV- = 10.4 V according to Figure 4. VS1,2,3 provide a high robustness against negative voltage in respect of VSS of -50 V. This ensures very stable designs even under rough conditions. VRU, VRV, VRW (low side emitter, Pin 12, 13, 14) The low side emitters are available for current measurements of each phase leg. It is recommended to keep the connection to pin VSS as short as possible in order to avoid unnecessary inductive voltage drops. V+ (positive bus input voltage, Pin 10) The high side IGBT are connected to the bus voltage. It is recommended, that the bus voltage does not exceed 500 V.
Data Sheet
7/18
Unit
Tstg TPCB
Wave soldering, 1.6mm (0.063in.) from case for 10s
C C C V Nm N/mm mm W
Tsol VISOL
IGBT and Diode Section Description Condition Symbol min Max. Blocking Voltage Tc = 25C,TvJ < 150C Tc = 80C,TvJ < 150C tp limited by TvJmax
VDD = 15V,VDC = 400V, TvJ = 150C VDD = 15V,VDC 500V, TvJ = 150C, IC = 10A VCEmax = 600V
Unit
DC output current
Repetitive peak collector current Short circuit withstand time2 IGBT reverse bias safe operating area (RBSOA) Power dissipation per IGBT Operating junction temperature range
A s
-40 -40
52 150 150
W C
1 2
Monitored by pin 24 Allowed number of short circuits: <1000; time between short circuits: >1s. 8/18 Rev. 2, March 2009
Data Sheet
Description
Condition
Symbol min
Unit
Single IGBT thermal resistance, junction-case Single diode thermal resistance, junction-case
RthJC RthJCD
K/W
Control Section Description Condition Symbol Value min Module supply voltage High side floating supply voltage (VB vs. VS) High side floating IC supply offset voltage ITRIP input voltage /FLT-TEMP Input voltage /HIN, /LIN Input voltage /FLT-TEMP Input current Operating junction temperature1 Max. switching frequency VIN = float tp < 500ns VDD VBS VS1,2,3 VIN,ITRIP VIN,FLT VIN IIN,FLT TJ,IC fPWM -1 -1 VDD-VBS-6 VDD-VBS-50 -1 -1 max 20 20 600 10 20 5.5 5 125 20 mA C kHz V Unit
Data Sheet
Static Parameters
(Tc = 25C, VDD = 15V, if not stated otherwise) Description Condition Symbol min Collector-Emitter breakdown voltage VIN = 5V, IC = 0.25mA Collector-Emitter saturation voltage VDD = 15V, Iout = +/-10A TvJ = 25C TvJ = 150C VIN = 5V, Iout = +/-10A TvJ = 25C TvJ = 150C VCE = 600V, VDD = 5V TvJ = 25C TvJ = 150C VDD = 15V, tSC 5s VCC = 300V, Tj = 150C V(BR)CES VCE(sat) 600 1.7 0.7 360 45 11.0 9.5 1.2 9.0 9.0 1.65 1.9 1.7 1.6 65 2.1 0.9 460 75 12.1 10.4 1.7 10.4 10.6 300 2.4 55 220 75 30 56 2.1 Value typ max V V Unit
VF
2.05
V A
Zero gate voltage collector current of IGBT Short circuit collector current1 Logic "0" input voltage (LIN,HIN) Logic "1" input voltage (LIN,HIN) ITRIP positive going threshold ITRIP input hysteresis VDD and VBS supply undervoltage positive going threshold VDD and VBS supply undervoltage negative going threshold VCC and VBS supply undervoltage lockout hysteresis Input clamp voltage (/HIN, /LIN) Input clamp voltage (ITRIP) Quiescent VBx supply current (VBx only) Quiescent VDD supply current (VDD only) Input bias current Input bias current ITRIP Input bias current Leakage current of high side FAULT low on resistance of the pull down transistors
ICES
40 1000 2.4 1.1 540 12.8 11.0 13.0 13.0 550 3.4 100 400 120 A V V mV mV V V V V V A mA A A A A
IC(SC) 2 VIH VIL VIT,TH+ VIT,HYS VDDUV+ VBSUV+2 VDDUVVBSUV-2 VDDUVH VBSUVH2
IIN = 4mA IIN = 4mA VHIN = low VIN = float VIN = 5V VIN = 0V VITRIP = 5V Tj,IC = 125C VFLT = 0.5V, VITRIP = 1V
1 2
Allowed number of short circuits: <1000; time between short circuits: >1s. Test is not subject of product test, verified by characterisation 10/18 Rev. 2, March 2009
Data Sheet
Dynamic Parameters
(Tc = 25C, VDD = 15V, if not stated otherwise) Description Condition Symbol min Turn-on propagation delay High side or low side Turn-on rise time High side or low side Turn-off propagation delay High side or low side Turn-off fall time High side or low side Shutdown propagation delay ITRIP Input filter time ITRIP Propagation delay ITRIP to FAULT Input filter time at LIN for turn on and off and input filter time at HIN for turn on only Input filter time at HIN for turn off Input filter time at HIN for turn off Fault clear time after ITRIP-fault Min. deadtime between low side and high side Deadtime of gate drive circuit IGBT Turn-on Energy (includes reverse recovery of diode) IGBT Turn-off Energy Iout = 10A, VDC = 300V TvJ = 25C TvJ = 150C Iout = 10A, VDC = 300V TvJ = 25C TvJ = 150C Iout = 10A, VDC = 300V TvJ = 25C TvJ = 150C VLIN,HIN = 0V; Iout = 10A, VDC = 300V VLIN,HIN = 5V Iout = 10A, VDC = 300V VLIN,HIN = 5V; Iout = 10A, VDC = 300V VLIN,HIN = 0V Iout = 10A, VDC = 300V VITRIP = 1V, Iu, Iv, Iw =10A VITRIP = 1V VITRIP = 1V VLIN,HIN = 0 V & 5V td(on) tr td(off) tf tITRIP tITRIPmin tFLT tFILIN 120 155 Value typ 639 34 854 40 1000 210 370 270 max 380 ns Unit
ms s ns J
Eoff
Erec
Data Sheet
11/18
Integrated Components
Description Condition Symbol1 min Resistor Resistor B-Constant of NTC (Negative Temperature Coefficient) Bootstrap diode forward voltage Capacitor Capacitor Bootstrap Capacitor TNTC = 25C TNTC = 25C IFDbs = 100mA Rbs RTS B25 VFDbs C1 Cgex CbsHx Value typ 10 100 4250 1.9 100 0.39 100 max 2.05 k K V nF Unit
Typical Application
Data Sheet
Characteristics
(Tc = 25C, VDD = 15V, if not stated otherwise)
27A 24A
25A
20A
15A
0A 2V 3V 0V 1V 2V
VCE, COLLECTOR EMITTER VOLTAGE Figure 5. Typical IGBT output characteristic (VDD = 15V)
VF FORWARD VOLTAGE Figure 6. Typical diode forward current as a function of forward voltage
1000ns
td(off) td(on) tr
1000ns
td(off)
td(on)
t, SWITCHING TIMES
100ns tf
t, SWITCHING TIMES
tf 100ns
10ns
tr
0A
10A
20A
25C
50C
75C
100C
125C
IC, COLLECTOR CURRENT Figure 7. Typical switching times as a function of collector current (inductive load, TJ=150C, VCE = 300V, VDD = 15V Dynamic test circuit in Figure A)
TvJ, JUNCTION TEMPERATURE Figure 8. Typical switching times as a function of junction temperature (inductive load, VCE = 300V, VDD = 15V, IC = 10A Dynamic test circuit in Figure A)
Data Sheet
13/18
Eon
2.50mJ
Eon
0.40mJ
E, SWITCHING ENERGY
2.00mJ
E, SWITCHING ENERGY
0.30mJ
Eoff
1.50mJ
1.00mJ
Eoff
IC, COLLECTOR CURRENT Figure 9. Typical switching energy losses as a function of collector current (inductive load, TvJ = 150C, VCE = 300V, VDD = 15V Dynamic test circuit in Figure A)
TvJ, JUNCTION TEMPERATURE Figure 10. Typical switching energy losses as a function of junction temperature (inductive load, VCE = 300V, VDD = 15V, IC = 10A Dynamic test circuit in Figure A)
1000kOhm
10 K/W
100kOhm
10 K/W
-1
10kOhm
1kOhm -25C 0C
10 K/W
-2
25C
50C
75C
100C
100ns 1s
TNTC, NTC TEMPERATURE Figure 11. Characteristic of NTC as a function of NTC temperature
tP, PULSE WIDTH Figure 12. Transient thermal impedance as a function of pulse width (D=tP/T)
Data Sheet
14/18
Erec = vD i F dt
0
t Erec
Figure A: Dynamic test circuit Leakage inductance L =180nH Stray capacitance C =39pF
LIN1,2,3 HIN1,2,3
90%
10%
10% tEon
2%
2%
Eoff =
v
0
CEx
i Cx dt
Eon = vCEx i Cx dt
0
t Eon
Data Sheet
15/18
tFILIN
LIN
on
off
on
off
high LO HO LO low
Data Sheet
16/18
Note: There may occur discolourations on the copper surface without any effect of the thermal properties.
Data Sheet
17/18
Description
Condition
Symbol min
Unit
Weight
mP
Note: There may occur discolourations on the copper surface without any effect of the thermal properties. Data Sheet 18/18 Rev. 2, March 2009
Free Download Daily Updated Database 100% Free Datasheet Search Site 100% Free IC Replacement Search Site Convenient Electronic Dictionary Fast Search System www.EEworld.com.cn
All Datasheets Cannot Be Modified Without Permission Copyright Each Manufacturing Company