Documente Academic
Documente Profesional
Documente Cultură
The Campbell operation facilities in York, PA, and Cortland, NY, conform to Quality Standard ISO 9001.
Contents 3001-3003 3031-3032 3041-3042 3061 3071, 3073 3072, 3074 3101-3103 3075 4091 4099 4102 4213, 4231 5012 5022 6150T CHB300
Page No. 136 - 137 137 138 139 140 141 142 143 143 145 144 146 - 147 148 147 148 147
Contents
(by Product)
Page No. 134 147 141 136 - 143 132 131 143 - 145 129 148 131 - 135 132 133 - 134 132 148 147 135 146 146 - 147 130 149
Bight Angle Factor Blocks, Linemans Blocks, Locking Blocks, Manila Rope Blocks, Lubrication Blocks, Selection of Blocks, Wire Rope Definitions Hooks Important Information Inspection of Blocks Load on Blocks Maintenance of Blocks Marine Hardware Public Utility Hardware Reeving of Blocks Sheaves, Manila Rope Sheaves, Wire Rope Warning Statement Campbell Blocks Numerical Index
128
Blocks
BLOCKS
www.cooperhandtools.com/campbell
Mechanical Advantage:
Parts of Line:
Loads
Ton: Proof Test: Ton is equal to 2240 LB unless otherwise noted. Campbell has the ability to proof test all blocks and fittings. The usual proof test is twice the Working Load Limit. Proof testing and certifying will be done at customers request, at extra cost. Blocks The result of a load which is applied off-center. The result of the rapid application of force (such as impacting and /or jerking), or the rapid movement of a static load. The average load at which a product fails, or no longer supports the load. The Working Load Limit (WLL) is the maximum resultant load which should ever be applied to the product in service, even when new, and when the load is uniformly applied in direct tension. Caution should be used when determining the resultant load, as the manner in which the product is used can increase the load. (Refer to Figure1, page 155)
Ultimate Load:
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
129
BLOCKS
WARNING Falling load may cause death or serious injury Do Not exceed Working Load Limit Do Not stand under load or in bight Do Not side load or shock load Do Not use worn or damaged block or rope IMPORTANT: Read and understand the instructions and warnings before using this block. It is the responsibility of the employer to place this information into the hands of the operator. INSTRUCTIONS FOR USE Do Not exceed the Working Load Limit of the block(s) being used. Check the label on the block or refer to the CooperTools catalog Do Not exceed the Working Load Limit or operating limitations of the rope being used. If uncertain, consult the rope manufacturer Use the recommended rope diameter. See the label or CooperTools catalog Know the weight of the load to be lifted and the conditions of the lift. For example, a flat load embedded in mud will require extra pulling power to break the vacuum and may create a shock load Be sure there are no impediments in the way of the lift that could snag the load and increase the load on the block(s) Blocks used above or aloft should be attached with shackles Do Not side load or shock load blocks. When using snatch blocks, be sure that the block is closed properly before the load is applied Snatch blocks should not be used for hoisting: they should be used for fairleading only Do Not stand under the load or in the bight area. Do Not stand in the direct line of pull of any load Be sure the structural member to which the block is being attached is strong enough to support the load Assure proper lubrication of the block. Improper lubrication can lead to block failure. Read and follow lubrication schedules.
130
Blocks
BLOCKS
www.cooperhandtools.com/campbell
Important Information
Block systems must be properly designed, used and maintained. A continual inspection program should be undertaken to discover gouges, distortion, cracks, elongation (or stretching), spread in the throat openings of hooks, severe wear or other damage. Any abuse, misuse or alteration may lessen the load a block system will sustain. Some examples of changes are as follows: Twisting or side loading Disfigurement Corrosion Shock loading Use for a purpose other than that for which a particular block was intended Use to carry a load in excess of the Working Load Limit Blocks consist of one or more sheaves fitted in a wood or metal shell. Blocks are supported by a fitting attached to the strap of the block. These blocks are intended to be used in conjunction with other components in a load-sustaining system to gain mechanical advantage. Care should be taken to select components of compatible type, size and Working Load Limit. Work Load Limits shown in CooperTools literature are applicable to new blocks, or blocks in as new condition.
Selection of Blocks
To select a block to fit your requirements, the following must be considered: 1. Are there regulations that could affect the choice of blocks, such as federal, OSHA, state, maritime, etc. 2. What loads (weight) will be lifted? This must be known to select a block with an appropriate work load limit. 3. How many parts of line are required? (See Method of Figuring, page 135.) 4. What is the size, type and working load limit of rope to be used? Consult a rope catalog to determine working load, rope strength and fatigue factors. 5. What is the speed of the line? This will help determine what type of bearing should be used. 6. Insure that the proper type of fitting is utilized. A block used above or aloft should be attached with shackles. 7. How will the block be reeved, and does it require a dead end becket? (See Method of Reeving Manila and Wire Rope Blocks, page 135.) 8. What is the fleet angle of the wire line? Line entrance and exit angles should be no more than 90. Use the bight angle factor (See page 134) to determine resultant load to properly determine Working Load Limit of your block.
131
Blocks
BLOCKS
Lubrication
The following represents the minimum recommended schedule for lubrication using medium viscosity lithium-based grease. Your own usage, including environmental factors and the frequency and type of use, may require lubrication that is more frequent. SHEAVE BEARINGS Blocks Tapered Rollers: Every 40 hours of continuous operation or every 30 days of intermittent operation. Roller Type: Every 24 hours hours of continuous operation or every 14 hours of intermittent operation. Bronze (Not self-lubricated): Every 8 hours of continuous operation or every 14 days of intermittent operation. HOOK BEARINGS Anti-Friction: Every 14 days for frequent swiveling or every 45 days for infrequent swiveling. Bronze Thrust/No Bearings: Every 16 hours for frequent swiveling or every 21 days for infrequent swiveling.
ADVERTENCIA
132 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
BLOCKS
www.cooperhandtools.com/campbell
Load on Blocks
WARNING
The Working Load Limit (WLL) is the maximum resultant load which should ever be applied to a block and its fittings. Blocks used to fairlead (single sheave and snatch blocks) can be subjected to a load greater than the weight being lifted or pulled.
Figure No. 1
Blocks
WARNING
The total weight (load) on a single sheave block or snatch block varies with the bight angle between the incoming and outgoing line to the block (see Figure 2).
133
BLOCKS
Blocks
Figure No. 3
134
BLOCKS
www.cooperhandtools.com/campbell
The methods of reeving tackle blocks will vary with the applications.
For example: To figure Parts of Line required when load lifted L and line pull P are known.
Parts of Line = Bronze Bushed Roller Bearing 1 0.96 0.98 2 1.85 1.9 3 2.8 2.9 4 3.6 3.8 5 4.4 4.7 6 5.2 5.6 7 5.9 6.5 8 6.6 7.3
You can see in the table at the right that an E factor of 5.3 requires 6 Parts of Line.
E Factors
Blocks
NOTICE: The product specifications and dimensions are as accurate as possible at the time of printing. However, because we are constantly improving the quality and design of our products, they can change without notice. 135
BLOCKS
Single 3001 AF
Double 3002 AF
mm 76
in. 4
1
mm 102
in. 5
5
mm 127
in. 6
3
mm 152
in. 8
mm 203
in. 10 1 8 6 4 1 4
5 1 1 1
mm 254
8
3
10
2
1
13
16
4
1
19
1 4 4 1 8
5 1 3
25
29
Sheave Size O.D. Rim Thickness Center Pin Dia. Weight lb Single Double Triple 1 1 2 2
1
1 4
1 3
44 13 10
2 4
5 3
57 16 10
3
3 3
76 19 10
3 2 1
1
89 25 13
121 29 16
159 32 16
2 8
8 8
4 8
kg .4 1 1
lb 2 3 4
kg 1 1 2
lb 2 2 4 5 2
1 1
kg 1 2 2
lb 4 6 2 9
1
kg 2 3 4
lb 9 2 13 17
1
kg 4 6 8
lb 17 25 32
kg 8 11 15
Blocks
Working Load Limit lb Single Double Triple 500 800 1200 kg 227 363 544 lb 1000 1400 1800 kg 454 635 816 lb 1200 1800 2400 kg 544 816 1089 lb 1800 2500 3200 kg 816 1134 1452 lb 2800 3800 4800 kg 1270 1724 2177 lb 4000 6000 8000 kg 1814 2722 3629
Block Size Inch 3 Fittings Type Round Loose Hook AF Single Double Triple Single Double Triple Single Double Triple 7205336 7206836 165894 165948 7205436 7206936 7208536 7205434 7206934 7208534 7205435 7206935 165900 165955 166006 104282 105210 106118 104299 105227 7205536 7207036 7208636 7205535 7207035 165917 165962 166013 104442 105371 7205636 7207136 7208736 7205635 7207135 7208735 165924 165979 166020 104596 105524 106422 7205835 7207335 104794 105692 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 mm 76 Inch 4 mm 102 Inch 5 mm 127 Inch 6 mm 152 Inch 8 mm 203
ADVERTENCIA
136 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
BLOCKS
www.cooperhandtools.com/campbell
3001 J Fittings Single with Becket Cat. UPC No. No. 020418 7209803 106767 7209814 169939 Double with Becket Cat. UPC No. No. 020418 7209815 167898 -
Blocks
mm 102
in. 5
5
mm 127
2
1
13
16
Single 3031 F
Double 3032 F
Sheave Size O.D. Rim Thickness Center Pin Dia. Weight lb Single Double Triple 2 3 3 2
1
2 4
5 3
57 16 10
3
3 3
76 19
Block Size Inch 4 Fittings Cat. No. 7231913 mm 102 UPC No. 020418 170126 Inch 5 Cat. No. 7231533 mm 127 UPC No. 020418 207358 -
8 8
4 8
10 Type
kg 1 1 2
lb 2 2 3 2 5
1 1
kg 1 2 2
Front Eye, Flatted, Loose Hook F Painted Bronze SL Bushed Iron Bushed Single Double Single Double
Working Load Limit lb Single Double Triple 500 600 900 kg 227 272 408 lb 700 900 1500 kg 318 408 680
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
137
BLOCKS
Single 3041 AF
mm 76
in. 4
1
mm 102
in. 5
5
mm 127
in. 6
3
mm 152
in. 8
mm 203
8
3
10
2
1
13
16
4
1
19
1 4 4 1 8
5 3 3
25
Sheave Size O.D. Rim Thickness Center Pin Dia. Weight lb Single Double 1 2 2 2 2
1 1
1 4
1 3
44 13 10
2 4
5 3
57 16 10
3
3 3
76 19 10
3 2 1
1
89 25 13
121 29 16
2 8
8 8
4 8
kg 1 1 1
lb 2 2 3 2 4 2
1 1 1
kg 1 2 2
lb 4 6 8
kg 2 3 4
lb 6 9 2 12
1
kg 3 4 5
lb 11 16 2 23
1
kg 5 7 10
Blocks
Triple
Working Load Limit lb Single Double Triple 700 1000 1400 kg 318 454 635 lb 1100 1600 2200 kg 499 726 998 lb 1300 2200 3200 kg 590 998 1452 lb 2000 3300 4000 kg 907 1497 1814 lb 3300 5100 7000 kg 1497 2313 3175
Working Loads are Resultant Working Loads. Block Size Inch 3 Fittings Type Round LooseHook AF Bronze SL Bushed, Galvanized Bronze SL Bushed, Galvanized Bronze SL Bushed, Single Double Triple Single Double Triple Single Double 7245335 7245334 7245336 171734 109034 109041 7245435 7246935 7248535 7245434 171765 171901 172045 109188 7247135 7247136 171963 110368 7247335 7248936 171987 111402 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 mm 76 Inch 4 mm 102 Inch 6 mm 152 Inch 8 mm 203
ADVERTENCIA
138 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
BLOCKS
www.cooperhandtools.com/campbell
*Warning: Do not exceed Working Load Limit. Lift should not exceed 500 pounds.
Blocks
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
139
BLOCKS
Wood, 3071 V
Steel, 3073 V
Specifications
Block Size in. 4 Diameter Rope Sheave Size O.D. Rim Thickness Bearing Diameter Center Pin Dia. 2
7 5 3
mm 102
in. 6
7
mm 152
in. 8
mm 203
19
22
1 4 2 1 8
7 3 1
25
51 22 16 10
3 1 8
3 1
76 29 19 13
114 35 22 16
8 8 3 8
lb
4 1 2
lb 9 6
8 5 8
lb 12 2 13
1
Blocks
Weight kg 1 1 kg 4 3 kg 6 6
2 2
kg 340
lb 2400
kg 1089
lb 4800
kg 2177
Block Size Inch 4 Fittings Type Stiff Swivel Hook with Latch V Bronze Bushed, Galvanized Bronze Bushed, Galvanized Wood, 3071 Steel, 3073 7265486 112881 7265686 7265696 113130 113192 7265886 7265896 113420 113482 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 mm 102 Inch 6 mm 152 Inch 8 mm 203
ADVERTENCIA
140 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
BLOCKS
www.cooperhandtools.com/campbell
Wood, 3072 V
Steel, 3074 V
Specifications
Block Size in. 6 Diameter Rope Sheave Size O.D. Rim Thickness Bearing Diameter Center Pin Dia. Weight 3 1 8
3 1 7
mm 152
in. 8
mm 203
22
1 4 2 1 8
7 3 1
25
76 29 19 13
114 35 22 16
4 1 2
lb
8 5 8
lb 12 2 13
1
Blocks
kg 4 3
kg 6 6
9 6
kg 1361
lb 5000
kg 2268
Block Size Inch 6 Fittings Type Stiff Swivel Hook with Latch V Bronze Bushed, Galv. SL Bronze Bushed, Galv. SL Wood, 3072 Steel, 3074 7267186 7267196 114250 114311 7267396 114472 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 mm 152 Inch 8 mm 203
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
141
BLOCKS
mm 51
8 - 12
10 - 13 51 16 10 kg 3 5 7
Single 3101 F
Double 3102 F
Triple 3103 F
Sheave Size O.D. Rim Thickness Center Pin Diameter Weight Single Double Triple Working Load Limit *
2
5
8 3 8
lb 7 12 16
lb kg Single 500 227 Double 1000 454 Triple 1200 544 Working Loads are Resultant Working Loads.
Blocks
Fittings Cat. Type No. Loose, Hook with Latch F Single Double 7222213 Triple 7223213 Loose, Swivel Hook with Latch G Single 7220214 Double 7222214 UPC No. 020418 107320 107375 107276 107337
ADVERTENCIA
142 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
BLOCKS
www.cooperhandtools.com/campbell
mm 152
22
76 29 Block Size 19 13 Fittings Type Stiff Swivel Hook with Latch V Safety, 3075 7268796 115004 Note: SL stands for self-lubricating bushings. Cat. No. UPC No. 020418 Inch 6 mm 152
4 1 2
Blocks
mm 16
Sheave Size O.D. Rim Thickness Bearing Diameter Center Pin Diameter Weight lb 34 Working Load Limit ton 7 Working Loads are Resultant Working Loads. kg 6350 kg 15 6 1 4 1 4 1
1 1
152 32 32 25 Fittings
4091V
Cat. No. 7329919 UPC No. 020418 123221
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
143
BLOCKS
4102V
Block Size Inch 6 Fittings Type 4102 with Galvanized Finish Fitting V 7336624 123849 Cat. No. mm 152 UPC No. 020418
Diameter Rope Sheave Size O.D. Rim Thickness Bearing Diameter Center Pin Diameter Weight
Manila Wire
8 3 8
3 1 8 1
1 1
76 29 25 13
kg 5
kg 1814
Blocks
* Warning: Do not exceed Working Load Limit Working Loads are Resultant Working Loads.
ADVERTENCIA
144 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
BLOCKS
www.cooperhandtools.com/campbell
4099 Q
mm 76 -
in. 4 2 1
1 1
mm 114 25 13
in. 6 1 2
3 1
mm 152 38 19
10
2
1
Sheave Size O.D. Center Pin Dia. Weight lb w/Connection w/o Connection Working Load Limit ton 2 kg 1814 ton 4 kg 3629 ton 8 kg 7258 5 3 kg 2 1 lb 12 6 kg 5 3 lb 26 15 kg 12 7 3
3
76 19
4 2 1
114 25
6 1 2
1
152 38
Blocks
Working Loads are Resultant Working Loads. H Fittings Type Wire 3" Self-lube 4 1/2" Bronze 6" Bronze PL 7339750 7339760 7339790 124716 124778 124952 7339754 7339764 7339794 124754 124815 124990 7339752 7339762 7339792 124730 124792 124976 7339756 185977 7339755 7339765 124761 124822 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 Cat. No. UPC No. 020418 V Q P NC
Connection Types
"H" - Hook, no latch "V" - Hook, with latch "Q" - Screw pin anchor shackle "P" - Drilled swivel eye "NC" - No connection
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
145
S H E AV E S
mm
mm 10 10 10 13 16
mm 10 13 16 19 25
Bronze Bushed Self-lube Cat. UPC No. No. 020418 7344032 7344132 7344232 7344432 7344832 126475 126482 126505 126536 126581
1 4 44 2 4 57 3
1 3
76
2 8 3 4
1 1 8
1
3 2 89
4213
4 4 121
8 8 3 8 1 2 5 8
8 2 5 8 3 4
1
4231 Specifications
A Outside Diameter in. mm 3 3 4 4 4 5 6 6 6 6 6 6 6 6 6 76 76 102 102 102 127 152 152 152 152 152 152 152 152 152 B Rim Width in. mm
1 3
Blocks
Weight lb kg
5 3
Iron Bushed Cat. UPC No. No. 020418 7350922 7351022 126925 126932 -
Bronze Bushed Self-lube Cat. UPC No. No. 020418 7360122 7360222 7360522 7365522 7365622 7360922 7361022 7361234 7361432 7361222 7361224 7361322 7361422 7361522 127649 127656 127694 128363 128370 127755 127762 127809 127854 127786 127793 127830 127847 127861
2 4 3 4 3 4
1 1
3
13 19 19 19 25 25 19 25 25 25 25 25 25 25 25
1 1 1 1 1 1 1 1
8 8 1 2 3 4 3 4 3 4 5 8 3 4
1
5 3
10 10 13 19 19 19 16 19 25 16 19 19 22 25
8 4 3 4 7 8
1 1 4
1
32
16 16 13 16 13 16 1 1 16 1 1 16 13 16 1 1 16 1 1 16 1 1 16 1 1 16 1 1 16 1 1 16 1 1 16 1 1 16
13
14 21 21 21 27 27 21 27 27 27 27 27 27 27 27
29 29 38 38 51 54 54 57 57 54 54 54 54 54 57
4 8 3 8 3 8 1 2 1 2 3 8 3 8 3 8 1 2 1 2 1 2 1 2 1 2 1 2
6 10 10 10 13 13 10 10 10 13 13 13 13 13 13
8 4 1 1 2 1 1 2 1 2 2
3 3 4 4 4 4 4 2 4 2 4 2 4 2 4 2 4 2
1 1 1 1 1 1 3 3
0.28 0.34 0.68 0.68 1.13 1.36 1.36 2.15 2.15 2.04 2.04 2.04 2.04 2.04 2.04
7351122 126949 -
ADVERTENCIA
146 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
S H E AV E S
&
BLOCKS
www.cooperhandtools.com/campbell
Weight lb kg 6 4 6 4
1 1
Bronze Bushed Self-lube Cat. UPC No. No. 020418 7361722 7361733 127885 127892
4 3 4
19 19
27 27
54 54
2 1 2
13 13
2.84 2.84
Bronze Bushed, SL Cat. No. 7380602 7380603 UPC No. 020418 129841 129858
1.13
Blocks
1.02
7380302
1.65 0.75
ADVERTENCIA
Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
147
BLOCKS
&
HOOKS
Weight lb kg 19 22 9 10
Finish Galvanized
Weight lb kg 19 9
Blocks
ADVERTENCIA
148 Antes de usar las pastecas, conozca el limite de carga de trabajo de los mismos. NO EXCEEDA EL LIMITE DE CARGA DE TRABAJO. Las cargas de trabajo son las fuerzas resultantes de las cargas de trabajo.
WARNING Know the Working Load Limit of the block, or blocks, to be used. Working Loads are Resultant Working Loads.
DO NOT EXCEED THE WORKING LOAD LIMIT.
www.cooperhandtools.com/campbell
Page
Cat. No.
Page
Cat. No.
Page
7205336 ..................................136 7205434 ..................................136 7205435 ..................................136 7205436 ..................................136 7205535 ..................................136 7205536 ..................................136 7205635 ..................................136 7205636 ..................................136 7205835 ..................................136 7206836 ..................................136 7206934 ..................................136 7206935 ..................................136 7206936 ..................................136 7207035 ..................................136 7207036 ..................................136 7207135 ..................................136 7207136 ..................................136 7207335 ..................................136 7208534 ..................................136 7208536 ..................................136 7208636 ..................................136 7208735 ..................................136 7208736 ..................................136 7209803 ..................................137 7209814 ..................................137 7209815 ..................................137 7220214 ..................................142 7222213 ..................................142 7222214 ..................................142 7223213 ..................................142 7231533 ..................................137 7231913 ..................................137 7245334 ..................................138 7245335 ..................................138 7245336 ..................................138 7245434 ..................................138 7245435 ..................................138 7246935 ..................................138 7247135 ..................................138 7247136 ..................................138 7247335 ..................................138 7248535 ..................................138 7248936 ..................................138 7265486 ..................................140 7265686 ..................................140 7265696 ..................................140 7265886 ..................................140 7265896 ..................................140 7267186 ..................................141
7267196 ..................................141 7267396 ..................................141 7268796 ..................................143 7269812 ..................................139 7329919 ..................................143 7332234 ..................................144 7339750 ..................................145 7339752 ..................................145 7339754 ..................................145 7339755 ..................................145 7339756 ..................................145 7339760 ..................................145 7339762 ..................................145 7339764 ..................................145 7339765 ..................................145 7339790 ..................................145 7339792 ..................................145 7339794 ..................................145 7344032 ..................................146 7344132 ..................................146 7344232 ..................................146 7344432 ..................................146 7344832 ..................................146 7350922 ..................................146 7351022 ..................................146 7351122 ..................................146 7351722 ..................................147 7360122 ..................................146 7360222 ..................................146 7360522 ..................................146 7360922 ..................................146 7361022 ..................................146 7361222 ..................................146 7361224 ..................................146 7361234 ..................................146 7361322 ..................................146 7361422 ..................................146 7361432 ..................................146 7361522 ..................................146 7361722 ..................................147 7361733 ..................................147 7365522 ..................................146 7365622 ..................................146 7380101 ..................................148 7380300 ..................................147 7380302 ..................................147 7380601 ..................................147 7380602 ..................................147 7380603 ..................................147
149
Blocks
150
Blocks