Documente Academic
Documente Profesional
Documente Cultură
BTM-222
Outline
Application
Access point Domestics and Industrial applications Serial Adapter GPS, POS, Barcode Reader
Block Diagram
Electrical Characteristics
Absolute Maximum Ratings Parameter Min. Storage Temperature -40 Supply Voltage(VDD) 2.7 Supply Voltage(PVCC) 3.0 Other Pin Voltage Vss-0.4 Recommended Operating Conditions Parameter Temperature Supply Voltage for UART Supply Voltage for USB General Electrical Specification Parameter Carrier Frequency RF Output Power RX sensitivity Load Impedance Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Average Current Consumption Min. -10 3.0 3.0 Max. +85 3.6 3.3 VDD+0.4 Max. +70 3.6 3.6 Unit DCV DCV DCV Unit DCV DCV
Description Measured in 50ohm No abnormal Oscillation RESET,UART,GPIO,PCM RESET,UART,GPIO,PCM UART,GPIO,PCM UART,GPIO,PCM Receive DM1
75
< 1000
<25
<40
<20 >16
2.402 Maximum Modulation f1 2.441 2.480 2.402 maz Minimum Modulation f2 2.441 2.480 Adjacent channel transmit power F=F02MHz Adjacent channel transmit power F=F03MHz
avg
Adjacent channel transmit power F>F0 +3MHz Adjacent channel transmit power F<F0 -3MHz
165 165 165 150 150 150 -35 -45 -50 -50
140<f1
avg
<175
kHz kHz kHz kHz kHz kHz dBm dBm dBm dBm
< - 70
> - 20 < 11 <0 <0 < - 30 < - 20 < - 40 < - 40 <-9 > -39
(note)
Relative transmit power /4 DQPSK Maximum carrier frequency stability w0 /4 DQPSK Maximum carrier frequency stability wi /4 DQPSK Maximum carrier frequency stability | w0 + wi | 8 DPSK Maximum carrier frequency stability w0
8 DPSK Maximum carrier frequency stability wi 8 DPSK Maximum carrier frequency stability | w0 + wi | /4 DQPSK RMS DVEM Modulation Accuracy 99% DEVM Peak DEVM 8 DPSK RMS DVEM Modulation Accuracy 99% DEVM Peak DEVM F>F0 +3 MHz F<F0 -3 MHz F=F0 -3 MHz F=F0 -2 MHz F=F0 -1 MHz F=F0 +1 MHz F=F0 +2 MHz F=F0 +3 MHz
< 75 for all packets < 75 for all blocks < 20 < 30 < 35 < 13 < 20 < 25 < -40 < -40 < -40 < -20 < -26 < -26 < -20 < -40 > 99
kHz kHz % % % % % % dBm dBm dBm dBm dBm dBm dBm dBm %
8 DPSK Maximum received signal level at /4 DQPSK 0.1% BER 8 DPSK /4 DQPSK C/I co-channel at 0.1% BER 8 DPSK Adjacent channel selectivity C/I /4 DQPSK F=F0 +1 MHz 8 DPSK Adjacent channel selectivity C/I /4 DQPSK F=F0 -1 MHz 8 DPSK Adjacent channel selectivity C/I /4 DQPSK F=F0 +2 MHz 8 DPSK Adjacent channel selectivity C/I /4 DQPSK F=F0 -2 MHz 8 DPSK Adjacent channel selectivity C/I /4 DQPSK F=F0 +3 MHz 8 DPSK Adjacent channel selectivity C/I /4 DQPSK F=F0 -5 MHz 8 DPSK F0 = 2405, 2441, 2477 MHz Adjacent channel selectivity C/I /4 DQPSK F=Fimage 8 DPSK
Note :
Measurement made using a POWER_TABLE entery of TX_PRE 80, INT PA63, EXT PA255. This ensures that the Bluetooth requirements for ACP and those defined by the FCC and ETSI are satisfied over the operating temperature rang of -5to +45. Although the design is capable of generating in excess of +18dBm, regulatory compliance over the full temperature range of -5 to +45 will not be satisfied if the transmit power approaches this value.
Pin Name
GND PVCC AIO(0) AIO(1) PIO(0) PIO(1) PIO(2) PIO(3) PIO(4) GND PIO(5) PIO(6) PIO(7) PIO(8) PIO(9) RESET VCC GND GND USB_DP USB_DN PCM_SYNC PCM_IN PCM_OUT PCM_CLK UART_RX UART_TX UART_RTS GND UART_CTS SPI_MOSI SPI_CSB SPI_CLK SPI_MISO PIO(11) PIO(10) RF_IO GND
Pin Type
GND Power Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional GND Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional CMOS input Power GND GND Bi-directional Bi-directional Bi-directional CMOS input CMOS output Bi-directional CMOS input CMOS output CMOS output GND CMOS input CMOS input CMOS input CMOS input CMOS output Bi-directional Bi-directional Analogue GND Common ground
Description
Power Amp. Power Supply(3.3V) Programmable I/O terminal , 32KHz sleep clock input Programmable I/O terminal Programmable I/O terminal, RX Enable Programmable I/O terminal, TX Enable Programmable I/O terminal, USB_PULL_UP, CLK_REQ_OUT Programmable I/O terminal, USB_WAKE_UP, CLK_REQ_IN Programmable I/O terminal, USB_ON, BT_Priority/Ch_Clk output for co-existence signalling Common ground Programmable I/O terminal, USB_DETACH, BT_Active output for co-existence signalling Programmable I/O terminal, CLK_REQ, WLAN_Active/Ch_Data input for for co-existence signalling Programmable I/O terminal Programmable I/O terminal Programmable I/O terminal Reset input of module, Active low reset Module power supply input Common ground Common ground USB data plus USB data minus Synchronous data sync Synchronous data input Synchronous data output Synchronous data clock UART data input UART data output UART request to send(active low) Common ground UART clear to send(active low) Serial Peripheral Interface data input Chip select for Synchronous Serial Interface(active low) Serial Peripheral Interface clock Serial Peripheral Interface data output Programmable I/O terminal Programmable I/O terminal Antenna interface Common ground
A
(Establish connection) a
When its in master mode. This command establish a connection. When its in slave mode, the command will be rejected.
Modifiers
A A1~A8
Description
Connect to a Bluetooth device (Its only available when ATD= xxxxxxxxxxxx assigned) Connect to a Bluetooth neighborhood device 1~8 (ATF? Result)
B D
Modifiers
Description
Inquire the Local BD address
For security purpose, We can specifies the unique remote device can be connected. In master role, it automatically inquire and search the slave even the slave is undiscoverable. In slave role, the command should be as a filter condition to accept the masters inquiry.
(Set Remote BD Modifiers Description address) D=xxxxxxx "xxxx-xx-xxxxxx" is 12 digit hex symbol xxxxx D0 (Default) D? Clear Remote BD address setting, inquire any slave in master mode or accept any master in slave mode. Inquire the Remote BD address setting
E
(Local Echo)
This command specifies whether the device should echo characters received from the UART back to the DTE/DCE.
Modifiers
E0 E1 (Default) E?
Description
Command characters received from the UART are not echoed back to the DTE/DCE. Command characters received from the UART are echoed back to the DTE/DCE. Inquire the current setting
This command is used to find any bluetooth device in neighborhood within 60 seconds timeout. If any device is found, its name and address will be listed. The search ends with a message Inquiry ends, xx device(s) found. This command is available only when the adaptor is in the master role.
Description
Inquire scan Bluetooth neighborhood devices.
H
(Discoverable Control)
This command specifies whether the device could be discovered by remote master device. note : waitting for 15 seconds afert ATH1 command to take the effect
Modifiers
H0
Description
The device enters undiscoverable mode. If a pair have been made, the original connection could be connected again. But other remote master device can not discovery this device. The device enters discoverable mode. Inquire the current setting
H1 (Default) H?
(Information)
Modifiers
I?
Description
Inquire the version Codes
K
(Stop setting) bits
This command is used to specify one or two stop bits of COM port
Modifiers
K0 (Default) K1 K?
Description
One Stop bit Two stop bits Inquire the current setting
L
(Baud Rate Control)
Modifiers
L0 L1 L2 (Default) L3 L4 L5 L6 L7 L?
Description
4800bps 9600bps 19200bps 38400bps 57600bps 115200bps 230.4Kbps 460.8Kbps Inquire the current setting
M
(Parity setting) bits
This command is used to specify the parity bit setting of COM port
Modifiers
M0 (Default) M1 M2 M?
Description
None Parity bit. Odd parity setting. Even parity setting Inquire the current setting
N
(Set name) device
We can specifies the device a friendly name using 0 to 9, A to Z, a to z, space and , which are all valid characters. Note that "firs space or -, last space or isnt permitted". The default name is Serial Adaptor
Modifiers
N=xxxxx D?
Description
"xxxxx" is a character string, maxima length is 16 Inquire the device name
When its in master mode .The command is used to enable/disable auto-connection feature. When its in slave mode, the command will be rejected.
Modifiers
(Auto connect O0 setting) (Default) O1 O?
Description
Automatically connectting to a device which is assigned in ATD or any available device if ATD was not assigned. Disable auto-connection feature, user should ATAcommand to connect a remote device. Inquire the current setting manually use
P
(Set PIN code)
This command specifies the PIN number. It control to off the PIN code authorization that allow to establish a connection without PIN code. Default PIN number is "1234"
Modifiers
P=xxxx
Description
"xxxx" is 4~8 digit string
(Default) P0 Turn off the PIN code authorization Inquire the current PIN number
P?
Q
(Result Code Supression)
The command is used to determine if result Codes should be sent to the DTE/DCE. When result Codes are supressed, the device does not generate any characters in response to the completion of a command or when an event occurs. Four Result Codes : OK,CONNECT,DISCONNECT,ERROR
Modifiers
Q0 (Default) Q1 Q?
Description
The device will send Result Codes to the DTE/DCE. The device will not send Result Codes to the DTE/DCE. Inquire the current setting
R
(Set Role)
This command specifies whether the device could be master or slave device. If change the role, the adaptor will warm start and clear all paired addresses.
Modifiers
R0 R1 (Default) R?
Description
The device as master role. The device as slave role. Inquire the current setting
U
(F/W upgrade)
This command will prompt Enter DFU mode, Are you sure (y/n)?message, then press Y to confirm the command. Then you should connect USB cable to PC and run DFU wizard. ( DFU wizard please contact us www.rayson.com)
Modifiers
U=pass word
Description
Pass word = RaysonUpgrade ,Go into Upgrade F/W Mode
Z
(Application setting)
Modifiers
Z0 Z?
Description
Restore factory default setting (19200bps, slave .) Inquire the current setting
The factory settings of UART are as follows: Baud rate: 19200 bps Data bit: 8 Parity: none Stop bit: 1 Flow control: H/W or none Others: Please refer to AT Command Sets.
BTM-22x Dimension
QPN Number
QPNHTTJ050
11.10.2005 11.10.2005
Applicant Information
Applicant Address Rayson Technology Co., Ltd 1F, No. 9, R&D Rd. 2, Science-Based Industrial Park, Hsin-Chu, 300 Taiwan, R.O.C URL http://www.rayson.com Contact Person Phone Number Fax Number Email Address Tim Lin +886.3.563.3666 +886.3.563.3688 sales@mail.rayson.com
Manufacturer Information
Product Information
Product Name Product ID Hardware Version Firmware Version Supported Protocol Supported Profile Class 1 Module BTM-22x, BTM-23x A1 cyt_8unified_fl_bt2.0_19p2 RF, BB, LM, HCI, HCI-USB, HCI-RS232, HCI-UART, L2CAP, SDP, RFCOMM GAP, SPP Product Category Product Type Software Version Components Comp-HW-Integrated N/A
Reference Information
Product Reference Document Bluetooth Specification Test Case Reference List V1.0 V2.0 + EDR TCRL_EDR_2005-1-BQRB1, TCRL_P1_1_2005-1-BQRB1
I certify that the Class 1Module has a Bluetooth Brand License based on the requirements as described in Section 6.2.1, Pre-Tested Bluetooth Components, of the Bluetooth Program Reference Document 1.0