Documente Academic
Documente Profesional
Documente Cultură
Mobile Repairing
Hardware Software
Voltage
Current Through Computer
Resistance
Basic Electronics
Q. What is an Atom?
A. An Atom is a smallest part of an Element which cannot be divided further.
Examples are Solid, Liquid and Gaseous States.
Q. What is Voltage?
A. Voltage is the force of electrons and the unit is measured in Volts. Circuit
Representation of voltage is (V).
The current flowing in the circuit is directly proportional to the voltage but inversely
proportional to the Resistance.
Ex.2. If the voltage is 3.6 V DC and the current is 400 mA calculate resistance.
V 3.6
Ans2: Using formula R= -> R= = 9Ω
I 0.4
Study of Multi-meter
• Turn the power off to the device and discharge any capacitors!
• Plug the black test lead into the COM jack.
• Plug the red test lead into either the
o 200 mA jack for small current measurements, or the
o 10 A jack for large current measurements.
• If you do not know the approximate current about to be measured, use the 10
A jack.
• Set the function/range switch to either
o DC amperes in the lower right, or
o AC amperes in the middle right.
• Break open the circuit at the point where you want to measure the
current by removing one of the wires. Connect the free end of the red
test lead to one place at which the wire was attached. Connect the
free end of the black test lead to the other place at which the wire was
attached. Current is always measured with the meter in SERIES with
the device. If you do not understand the difference between SERIES
and PARALLEL, ask your TA. Using the current meter incorrectly will
blow the fuse or damage the meter. (It will also cost you points on
your lab writeup.)
• Reapply the power to the device.
• If the LCD displays either "1." or "-1." with all other digits blank, the current is
beyond the selected range. Use the switch to select a larger range.
• Once you know the approximate current through the device, then use the
switch to select the lowest current range that will still accomodate the current
through the device.
• Turn the power off to the device before removing the meter from the circuit.
• Turn the power off to the device and discharge any capacitors!
• Plug the black test lead into the COM jack.
• Plug the red test lead into the V jack.
• Set the function/range switch to ohms ( ) in the lower left.
• If you do not know the approximate resistance about to be measured, use the
largest range available.
• Connect the free ends of the red and black test leads ACROSS the device to
the measured. Resistance is always measured with the meter in PARALLEL with
the device.
• If the LCD displays either "1." or "-1." with all other digits blank, the resistance
is beyond the selected range. Use the switch to select a larger range.
• Once you know the approximate resistance of the device, then use the switch
to select the lowest range that will still accommodate the resistance of the
device.
Voltages
There are two types of voltages:
AC current is a high voltage and contain frequency of 50Hz means that in a second it
goes 50 times in positive and negative cycle.
Direct Current (DC) is a low voltage. Examples are Batteries (1.5 V to 24 V). It
doesn’t have frequency in it.
1) Passive Components
2) Active Components
Electronic
Components
Examples
Resistors
Semi-Conductors
Capacitors
Inductors
The active component changes the entire function of the circuit. The examples of
this are Semi-Conductors (AC to DC)
The passive component doesn’t have the ability to change the function of the circuit.
It only modifies and re-modifies their respective circuits. The examples of passive
components are as follows:
1) Resistors
2) Capacitors
3) Inductors
Resistors
Resistors are the electronic component which is used to drop the voltages. There are
3 types of Resistors:
Resistor Values
Resistor values that are available for use in circuits range from 0 to around
10,000,000 . Because dealing with large numbers like 10,000,000 is awkward,
the 'k' prefix is used to denote 1,000 and the 'M' prefix is used to denote
1,000,000. 'k' stands for 'kilo' and 'M' stands for mega. Here are some examples
of resistor values:
10M = 10,000,000 (pronounced 'ten mega Ohms' or 'ten meg' for short)
Sometimes you will see resistors quoted without the symbol, and sometimes the
symbol will be replaced with 'R'. When a fraction is needed in a value you will
often see 'R', 'k', or 'M' in place of the decimal point as an aid to clarity:
Tolerance
Like all components, resistors are never perfect. Their true value will never be
exactly the same as their stated value, but will be somewhere close. The
maximum amount of error in the value is given by the 'tolerance' value, expressed
as a percentage. Most resistors have a 10% - 20% tolerance, and this is normally
adequate for most applications. You can get 1% and 2% tolerance resistors if you
need them.
Because resistors are so small, it is not easy to print their value and tolerance on
them in a way which is easily readable. Therefore, one of the following colour
coding systems is used instead. Both systems code the value in Ohms - there are
no codes for 'k' or 'M'.
The Four-Band System
This system uses three coloured bands to represent a resistor's value, and an
additional coloured band spaced further apart to represent a resistor's tolerance, as
shown in figure 2.
• The first two bands give the the first two digits of the resistor's value.
• The third band is a multiplier and gives the number of zeroes that must be
placed after the first two digits.
• The forth band gives the resistor's tolerance as a percentage.
The table below shows the meaning of each colour for each of the bands. Notice
that most of the colours are in the order of the colours of a rainbow, with the
exception of indigo which is not used. There is a rhyme you can use to remember
these colours: Richard Of York Gave Battle in Vain.
3) Band1=Orange 3 33000 Ω = 33 K Ω
Band2=Orange 3
Band3=Orange 000
5) Band1=Orange 3 32000000 Ω = 32 M Ω
Band2=Red 2
Band3=Blue 000000
Variable Resistors
Variable Resistors are used to increase and decrease the resistances. The examples
in this category are as follows:
Fusable Resistor
The function of fusable resistor is to break the circuit when excess current flows
above its specification
Inductors
1) Coils
2) Transformers
Coils
Symbol:
The function of coil is to filter the voltage. When voltage is applied to a coil EMF
(Electro Motive Force) is generated.
Transformers
Step-Down Transformer
1) Conventional
2) Center-Tap Transformer
Conventional Transformer
All step down transformer lower the voltage due to high resistance in the primary
winding. Due to this an EMF is generated and the low voltage is passed from
primary to secondary winding. For Example, a step down transformer of 4.6 V AC
requires 240 V AC at the primary winding which is stepped down to 4.6 V AC at the
secondary winding.
Center-Tap Transformer
Center-tap Transformer has a center winding of 0 V, in other words we can say that
the secondary winding contains 3 wires, the center on is 0 Volts. Refer the diagram
for more.
Capacitors
The function of capacitor is to pass the AC voltage and store the DC voltage.
Capacitors are further divided into two categories:
1) Polarized
2) Non-Polarized
Polarized Capacitors
Symbol:
Looks:
Non-Polarized Capacitors
Symbol:
Looks:
Non-polarized capacitors are disc or ceramic capacitors. The unit is Pico fared.
Semi Conductors
Semi conductors are the elements which are partly conductors and partly insulators.
Example of element is Silicon. The examples of semi-conductors are as follows:
1) Diodes
2) Transistors
3) I.C. (Integrated Circuits)
Diodes
1) P.N. Junction
2) Zener Diode
3) L.E.D. (Light Emitting Diode)
Symbol: Layout:
Internals:
When we check a diode on a multi meter on buzzer mode, by placing the red probe
on the positive side and black probe on the negative side, we hear buzzer. It means
that the diode is Forward Bias. If we place the testing probe in the reverse order, we
do not hear buzzer, it means that the diode is reverse bias. It indicates that diode
works in one direction i.e. from Positive to negative which is called as Forward Bias.
P.N. Junction diodes convert AC to DC (Rectifier Circuit)
Zener Diode
Symbol: Layout:
Zener diode acts as a voltage stabilizer. It comes under different voltages such as 5
V, 10 V, 12 V etc.
Symbol: Layout:
The function of LED is that it emits light when voltage is passed to it. It is used as a
power indicator in the circuit. It operates under 1.5 V DC and comes under different
colors such as Red, Yellow, Green, Blue.
Rectifier Circuits
Rectifiers are the circuit which converts AC to DC voltage. The are 3 types of
Rectifier Circuits:
The Half Wave Rectifier is a circuit which converts AC to DC voltage. In this circuit,
only one P.N. Junction Diode is used. The internal Resistance of Primary Winding of a
transformer is very high because of this the voltage is dropped to 6 volts AC. In
between the core of Primary Winding and Secondary Winding, EMF is generated and
the voltage is transferred to the secondary winding. At the output of secondary
winding, we get step down voltage of 6 V AC form (It will have 50 Hz. Frequency).
So a PN Junction Diode is connected in series. The diode will only forward bias the
positive half cycle of AC voltage. But there are chances of AC Leakage (Ripples)
which may damage the battery at the time of charging. Therefore, an Electrolytic
Capacitor is used to bypass DC and block AC voltage.
A Zener Diode is used to stabilize the voltage. It is of 6 V. The Zener diode will start
working when more than 6V is applied to it. It will break the circuit when excess
voltage comes. LED is used as a power indicator and a Resistor is attached to it to
drop the voltage because LED works on 1.5 V and our circuit is of 6V.
With Respect to half wave rectifier this gives better performance because at the
same time 2 diodes are Forward Bias so we get double positive half cycle. This
minimizes the AC Leakage chances. Rest of the circuit is same.
Bridge Rectifier
Bridge Rectifier gives the same performance of the full wave rectifier. This circuit can
be prepared by using conventional tansformer using Bridge Rectifier Module and rest
remain same.
Transistors
Transistor acts as an open switch. The input voltage is a form of AC which is given to
the base of Transistor. Transistor are used for amplification of the signal (Convert
Weak signals into stronger signals)
NPN Transistors
Symbol: Layout:
When we check a NPN transistor on a Multimeter by keep the red probe on the base
of the transistor and the black probe on either Collector or Emitter, we can hear
buzzer. This indicates the following:
When do this in reverse order, we do not hear buzzer. This indicates the following:
Example Circuit:
When
PNP Transistor
Symbol: Layout:
When do this in reverse order, we do not hear buzzer. This indicates the following:
Example Circuit:
I.C. Integrated Circuits
Integrated Circuits have many inbuilt components in it and it is designed as per the
circuit requirements. There are 2 types of I.C.
All the major sections in the Electronic devices are controlled by IC’s. For Example,
Most of the faults in the electronic devices are because of IC’s. They have most of
the load on them.
1) Solder Wire (Trip 60/40 i.e. 60% Aluminium and 40% Tin)
2) Liquid Soldering Paste / Soldering Flux