B-Series (Brocade) switches uses both web and CLI, the table below displays some
commons uses but not all the CLI commands.
B-Series (Brocade) zoning commands are detailed in the below table help prints available commands switchdisabled disable the switch switchenable enable the switch portdisable Disable a specified port portenable Enable a specified port porterrshow Print port error summary portname show the portname or you can rename the portname portcfgpersistentdisable Persistently disable a port portcfgpersistentenable Enable a persistently disabled port licenseadd Adds license keys to switch licensehelp license commands licenseshow Displays current license keys diaghelp diagnostic commands configure change switch parameters (BB credits, etc) date Print/set the system date and time uptime Print how long switch has been up diagshow POST results since last boot routehelp routing commands switchshow display switch show (normally first command to run to obtain switch configuration) supportshow prints switch information for debugging purposes portshow # display port info nsshow nameserver contents nsallshow NS for full fabric fabricshow show fabric membership info Firmwareshow display firmware versions in the switch reboot full reboot with POST switchreboot Halts and restarts the operational switch. firmwarecommit Commit firmware to stable storage firmwaredownload Download firmware into switch firmwaredownloadstatus display the progress and status of firmwareDownload firmwarerestore Restore the old firmware in the switch fabswitchshow display fabric switch state information errshow print error log errdump print error log (no page breaks) fastboot reboot without POST zonecreate (zone) create a zone zonecreate "arg1", "arg2" zoneshow shows defined and effective zones and configurations zoneadd adds a member to a zone zoneadd "arg1", "arg2" zoneremove removes a member from a zone zonedelete delete a zone cfgcreate (zoneset) create a zoneset configuration cfgclear clears all zoning information (must disable the effective config first) cfgadd adds a zone to a zone configuration cfgshow display the zoning information cfgenable enable a zone set cfgsave saves defined config to all switches in fabric across reboots cfgremove removes a zone from a zone configuration cfgdelete deletes a zone from a zone configuration cfgdisable disables the effective zone set Page 1 of 4 SAN Switch cheat sheet for B-Series (Brocade) | M-Series (Mcdata) | MDS-Series (Cisco... 1/14/2011 http://www.sanduel.com/SAN-Storage-Commands/SAN-Switch-cheat-sheet-for-B-Series-...
B-series creating a zone commands
Tips In CLI, you can list out the data you want by using these commands. Example: switchshow |grep hostname Switchshow |grep zonename
M-Series (Mcdata) switches uses both web GUI and CLI, the table below displays some commons uses but not all the CLI commands.
There are several commands that allow you to navigate through the switch "..", "ctrl-U" and "root" .
M-Series (Mcdata) zoning commands are detailed in the below table
Zoning limits 64 zone sets (max) 2000 zones (max) 1024 zones per zone set (max) default should all ways be disabled (causes all port to see each other creating Creating zone by WWN zonecreate "zone1", "10:00:00:e0:69:20:07:10 ; 50:06:04:80:b8:91:c2:ce" Create a zone configuration cfgcreate "FabricName_cfg", "zone1 ; zone2" saving the zone configuration cfgsave (this will save across reboots) enable the zone configuration cfgenable "FabicName_cfg" saving the zone configuration cfgsave view zoning information zoneshow or cfgshow commadelim Toggle comma-demlimited display mode config configure settings login login into CLI with different access rights maint maintenance settings perf Performance statistics reserved reserved for future development show display attributes features configure feature settings ip configure IP settings logout logout of the CLI port configure port data security configure security settings snmp configure snmp switch configure switch data system configure system data zoning configure zoning settings showactive show actively running zoneSet clearzone clear WWN's in a zone deletezone remove zone from running config activezoneset activation of changes addzone add a new zone to the working area addwwnmem add a WWN to a zone showpending show pending zones renamezone rename a zone deletewwn delete a WWN from a zone renamezoneset rename a zone set Page 2 of 4 SAN Switch cheat sheet for B-Series (Brocade) | M-Series (Mcdata) | MDS-Series (Cisco... 1/14/2011 http://www.sanduel.com/SAN-Storage-Commands/SAN-Switch-cheat-sheet-for-B-Series-... ghosts in a FA's login table)
MDS-Series (Cisco) switches uses both web GUI and CLI, the table below displays some commons uses but not all the CLI commands, the ones highlighted will be the ones used most often. EXEC mode commands:
CONFIG mode commands:
attach connect to a specific linecard bios BIOS related commands callhome callhome commands clear reset functions clock manage the system clock config enter configuration mode debug debug functions discover discover information exit exit ffrom the submode fcping Ping a N_Port fctrace trace a route for a N_Port load load system image no disable debugging functions reload reboot the switch setup run the basic setup command facility show display running system information system system management commands test test command write write the current configuration zone zoning server commands aaa config aaa boot configure boot variables callhome enter the callhome configuration mode clock configure time and date fcalias fcalias configuration commands fcanalyzer configure fabric analyzer fcc configure FCC congestion control fcdomain enter the fcdomain configuration mode fcdroplatency configure switch or network latency fcflow configure fcflow fcinterop interop commands fcns Name server configuration fcroute configure FC routes fcs Configure fabric config server fctimer configure fibre channel timers fspf configure fspf interface select an interface to configure Cisco Config Manager Looking for a Configuration tool for Routers, Switches? Download Now ManageEngine.com/DeviceExpert Simple Storage Solutions Flexible, High-Performance Scale-Out Storage. Buy Today. CA. www.Coraid.com Page 3 of 4 SAN Switch cheat sheet for B-Series (Brocade) | M-Series (Mcdata) | MDS-Series (Cisco... 1/14/2011 http://www.sanduel.com/SAN-Storage-Commands/SAN-Switch-cheat-sheet-for-B-Series-...
There are several commands that allow you to navigate through the switch "cd", "copy", "dir", "find", "mkdir", "move", "rmdir" and "tail". MDS-series creating a zone
MDS-series common commands
ip configure IP features no Negate a command or set its default ntp NTP configuration power configure power supply poweroff power off module in switch qos Configure priority of FC control frames radius-server configure radius related parameters role configure roles snmp-server configure snmp span enter SPAN configuration mode ssh configure ssh parameters switchname configure systems network name system system config command trunk configure switch wide trunk protocol username configure username information vsan enter the vsan configuration mode zone zoning configuration commands zoneset zoneset configuration commands create a zone and place it in the vsan # zone name testzone1 vsan 4 add a member (port wwn example) # member pwwn 10:00:00:00:c9:21:40:b8 (port on the host) add a member (fabric port wwn example) # member fwwn 10:01:10:01:10:ab:cd:ef (port on the switch) add a member (FCID example - hard zoning) # member fcid 0x7f0000 (24 bit address) add a member (FC alias example) # member fcalias payroll display logged in WWN, display vsan information # show flogi database display the specific vsan logins # show fcns database vsan 4 activatng a zoneset # zoneset activate name zone1 vsan 4 delete a zoneset # clear zone dataabse vsan 4 configure the default zone # zone default-zone permit vsan 4 display zones and zonsets # show zoneset active # show zoneset # show zoneset active vsan 4 copy active zone set to the full zone set # zone copy active-zoneset full-zoneset vsan 4 distribute the full zoning database to others switches # zoneset distribute full vsan 4 Page 4 of 4 SAN Switch cheat sheet for B-Series (Brocade) | M-Series (Mcdata) | MDS-Series (Cisco... 1/14/2011 http://www.sanduel.com/SAN-Storage-Commands/SAN-Switch-cheat-sheet-for-B-Series-...
VNVNX5200,-VNX5400,-VNX5600-VNX5800,-VNX7600-and-VNX8000-Storage-Systems-DiskX5200, VNX5400, VNX5600 VNX5800, VNX7600 and VNX8000 Storage Systems Disk and OE Matrix