0 evaluări0% au considerat acest document util (0 voturi)
106 vizualizări56 pagini
Beckhoff offers a universal, scalable building automation control system. The core of the intelligent building control is the Beckhoff Industrial PC with TwinCAT automation software. The standardised communication protocols BACnet / IP, OPC-UA and Modbus-TCP facilitate integration of industrial PCs in existing systems.
Beckhoff offers a universal, scalable building automation control system. The core of the intelligent building control is the Beckhoff Industrial PC with TwinCAT automation software. The standardised communication protocols BACnet / IP, OPC-UA and Modbus-TCP facilitate integration of industrial PCs in existing systems.
Beckhoff offers a universal, scalable building automation control system. The core of the intelligent building control is the Beckhoff Industrial PC with TwinCAT automation software. The standardised communication protocols BACnet / IP, OPC-UA and Modbus-TCP facilitate integration of industrial PCs in existing systems.
Beckhoff | Intelligent Building Automation PC-based control technology from Beckhoff, which has already been used success- fully for almost three decades in all areas of industrial automation, has become an integral component of intelligent building automation. The demands on the intel- ligence of buildings have increased constantly in recent years, such that the energy efciency as well as a good return on investment is the priority. The idea of a green building based on sustainable, energy-efcient construction and building use can be realised with intelligent, integral building automation. Beckhoff offers a universal, scalable building automation control system covering PC- and Ethernet- based controllers and a modular I/O system for logging all data points in buildings. In the Beckhoff I/O system, an extensive range of Bus Terminals is available to building technicians for connect the sensor and actuator systems. This provides the freedom to assemble the modules required for the application as if from a construction kit. On top of that, the ne granularity of the terminals permits precise tailoring of the I/O level to actual needs; i.e. only that which is actually needed must be purchased. The core of the intelligent building control is the Beckhoff Industrial PC with TwinCAT automation software. For all areas of application, from the small controller to automate a single room or a certain building zone up to a high-performance computer for the control of a large HVAC system, Beckhoff offers a scalable product range from which the building technician can choose. The free program- mability of the controller is extremely helpful in the realisa- tion of very complex tasks. Comprehensive software libraries that were specially developed for building automation and simplify and opti- mise software engineering round off the Beckhoff portfolio. Object-oriented function blocks ensure good readability and expandability of the user programs. In addition, they guar- antee high system functionality and reusability of templates. 2 New Automation Technology BECKHOFF 3 Openness is another advantage of the Beckhoff platform for building automation. The standardised communication protocols BACnet/IP, OPC-UA and Modbus-TCP facilitate integration of Industrial PCs in existing systems. All common eldbus sys- tems used in building automation, including LON, EIB, DALI and MP-Bus, can be inte- grated in the control system via intelligent Bus Terminals. PC-based control technology from Beckhoff offers a high potential for the opti- misation of energy efciency in buildings. The Beckhoff solution already makes building automation of energy efciency class A according to DIN EN 15232 possible today. Solutions for consumption data acquisition from the I/O Bus Terminal to the ERP system as well as solutions for energy optimisation, for example, in computer centres, round off the range of offers. www. beckhoff.com/building 4 Architects and planners System integrators IP-based network conguration facili- tates integration of the automation system into the building infrastructure already during the design phase. free choice of topology, depending on the requirements in a particular building Integrated design is simplied through exible application of input/output mod- ules, independent of the control system and function. Investors universal solution based on a transparent automation system central data management added value through integration of all services in a single system and utilisation of synergy effects for energy saving The payback time for integrated automa- tion is approx. ve years. Extension and modication of the system in order to adapt it to changing technical requirements is straightforward over the whole life cycle. Reduction of the number of actual physical data points reduces the poten- tial for errors during installation and commissioning. transparent access to the whole system for display/processing of parameters simplied maintenance and optimisation of the system seamless integration of room automation with the primary systems Advantages of integrated building automation New Automation Technology BECKHOFF 5 Maximum exibility PC-based control technology enables all building functions and function changes to be realised based on software. This means maximum exibility and low engineering costs. The comprehensive TwinCAT building libraries cover all main building functions. Beckhoff Building Automation | The integrated building automa Lighting HVAC Room automation Facade The functionalities are integrated based on a holistic building auto- mation concept so that all the benets with regard to integration of the automation, minimisation of capital cost, optimisation of maintenance and increased energy efciency can be utilised. New Automation Technology We reserve the right to make technical changes. BECKHOFF 6 tion concept Remote maintenance Logging of energy data Home automation Operating and monitoring Modular automation components The Beckhoff Bus Terminal system for connection of data points features 400 different I/O terminals and supports all common sensors and actuators. Scalable control technology The scalable, modular control system from Beckhoff offers the right solution for any task, from the high-performance Industrial PC or Embedded PC as main building computer up to local Ethernet controllers. New Automation Technology BECKHOFF We reserve the right to make technical changes. 7 Beckhoff Building Automation | Lighting Both natural and articial light have a signicant inuence on the well-being of humans. Suitable lighting can have a positive effect on consumption behaviour and work performance. Lighting is therefore becoming increasingly important as a building automation parameter. In addition to the right choice of lamps and ttings, another important aspect is the control of different lighting scenarios. New Automation Technology We reserve the right to make technical changes. BECKHOFF 8 Beckhoff offers a wide range of products for lighting control: universal dimmers KL2751 (300 VA) and KL2761 (600 VA) for controlling ohmic, inductive or capacitive loads, automatic load detection and calculation of the correct phase control angle light switching: KL2602 (loads up to 5 A AC/DC ohmic and 2 A AC/DC inductive); KM2614 (with integrated manual opera- tion) and KM2604 (up to 16 A per output) KL2512 for switching or dimming of negative switching 24 V DC LEDs via PWM The DALI master terminal KL6811 offers benets in relation to cabling effort and diagnostic options. The terminal is control- led through the building automa- tion software library DALI/DSI V2, based on the DALI standard (IEC 60929). The library contains expansion commands for dis- charge lamps and emergency lighting. DMX master EL6851 for control- ling of facade or effect lighting; DMX slave EL6851-0010 for integration in stage lighting. The terminals are integrated via EtherCAT. The TwinCAT PLC Building Auto- mation software library offers comprehensive lighting control function blocks such as constant light control. 2 A 16 A LED DALI DMX Ethernet New Automation Technology BECKHOFF We reserve the right to make technical changes. 9 Beckhoff Building Automation | HVAC The tightening of energy saving regulations for buildings over recent years led to increas- ing demands and complexity in HVAC control software. The Beckhoff HVAC library offers system integrators a software tool that covers the whole functionality of HVAC control systems. It includes ready-made software components for energy saving functions such as summer night cooling, summer compensation, cool down protection, time schedulers and much more. New Automation Technology We reserve the right to make technical changes. BECKHOFF 10 The software library offers the fol- lowing benets for programmers during system setup and for system operators during routine operation: efcient parameterisation and commissioning consistently high system functionality transparency of programs (prerequisite for long-term maintainability and expand- ability of the systems) improved reusability of tem- plates for systems or system components straightforward familiarisation of service staff uncomplicated extension of existing systems clear, object-oriented structure for creating visualisation objects in HMI and SCADA systems good documentability of the programs T Room T P T T T Ethernet New Automation Technology BECKHOFF We reserve the right to make technical changes. 11 Beckhoff Building Automation | Room automation Integrated room automation covering different functionalities is the key to efcient building operation and well-being of the users and offers signicant savings potential. Intelligent link- ing of the individual physical data points reduces not only their number and error-proneness, but also energy consumption. This leads to signicant cost reduction during the construction phase and during operation. New Automation Technology We reserve the right to make technical changes. BECKHOFF 12 Communication between the individual automation stations takes place via Ethernet TCP/IP. The degree of automation of a particular room can be individually adapted through custom congura- tion of the Bus Terminals. Alterna- tively, the BC9191 room controller integrates these functions in a module. Rooms or areas with repeating requirements only have to be programmed once. The pro- gram template can then be copied as required and enables integrated, efcient room automation based on energy efciency classes. Energy efciency classes regarding DIN EN 15232 Function D C B A Evaluation of occupancy x x Scheduler x x Light switching x Automatic lighting x x Daylight-dependent lighting x x Constant light control x x Sunscreen automatic x Lamella setpoint tracing x x Blind correction x x Thermoautomatic x x Selection of energy level x x Selection of energy level with start optimisation x x Function D C B A Setpoint calculation x x Feature selection x x Room temperature control (heating/cooling) x x x Room/supply air tempera- ture cascade control x x Fan control x x Sequence control x x Setpoint limitation x x Air quality control x Night cooling x x Load optimisation x x Ethernet, ADS, Modbus TCP, BACnet/IP, OPC-UA Lighting Cooling Lighting New Automation Technology BECKHOFF We reserve the right to make technical changes. 13 Beckhoff Building Automation | Facade Building facades have to meet a wide range of demands. The architectural design primarily focuses on aesthetic aspects. After all, the facade determines the visual appearance of a building. From an engineering point of view, the facade also has to meet thermal insulation, glare protection and safety requirements. New Automation Technology We reserve the right to make technical changes. BECKHOFF 14 Drives for blinds and other shading devices are controlled via digital output terminals such as KL2722 or KL2602. Shading can reduce heating or cooling performance through inte- gration into the room automation. Combination with lighting control offers further scope for energy opti- misation. Window contacts connected via digital input terminals such as the KL1404 are used for controlling the heating or cooling system and send information on the security status of the building to the control level. Electric window drives can be used to optimise air quality, for sum- mer night cooling and for smoke extraction. Integration of weather data can be realised via serial or analog inter- faces or via web services, depending on the degree of automation. This way, the facade is protected from wind and frost. Comprehensive function blocks from the Building Automation and HVAC software libraries round off the range of applications. Ethernet New Automation Technology BECKHOFF We reserve the right to make technical changes. 15 Beckhoff Building Automation | Remote maintenance Due to the complexity of the tasks involved, automation of buildings and properties requires access via remote diagnostics, maintenance and control. Swift support from specialists is a prerequisite for troubleshooting, software maintenance and installation of updates in order to avoid unnecessary costs and failures. Information about process parameters is required for building operation and system optimisation. Warning and error messages can be sent to service staff via SMS or e-mail. New Automation Technology We reserve the right to make technical changes. BECKHOFF 16 Diagnostics and Services networking via cable (analog, ISDN, DSL, ) or mobile commu- nication (GSM, EDGE, UMTS, ) availability of familiar Internet technologies such as FTP, HTML, AJAX, SOAP, WCF, REST, Web- Service or Silverlight through the use of PC-based automation technology IEC 60870-S-101, IEC 60870-S- 103 and IEC 60870-S-104 tele- control protocols are supported. Remote control Service staff can be notied directly from the control system via SMS or e-mail. Remote desktop applications or Team-Viewer enable the whole computer to be controlled via the Internet or Intranet, even over large distances. monitoring and operation via HTML pages stored directly in the control system dynamic display of content via AJAX and Silverlight Remote programming full access to the control system for changing the system congu- ration and the control program VPN routers offer safe and cost- effective access via Internet/ Intranet or mobile communica- tion. Ethernet ADS, OPC, Ethernet, Serial, USB, Bluetooth, Fieldbus, WiFi, WLAN New Automation Technology BECKHOFF We reserve the right to make technical changes. 17 Beckhoff Building Automation | Logging of energy data Due to rising running costs and increasingly centralised management of buildings, computer centres and properties, demand for energy and consumption data monitoring is increasing. Through the combination of PC technology and Bus Terminal components Beckhoff offers an ideal platform for realising these tasks. Seamless integration of energy and consumption data monitoring for all building functions into the automation system results in savings potential and synergy effects during system installation and building operation. New Automation Technology We reserve the right to make technical changes. BECKHOFF 18 Solutions for logging of energy data In conjunction with current trans- formers, the 3-phase KL3403 power measurement terminal enables measurement of all relevant electri- cal data and offers comprehensive network analysis for the building automation system. A function block from the HVAC software library measures RMS values of current and voltage, effective, apparent and reactive power, cos , etc. In many cases, electricity meters provide data in the form of pulse signals. Here too, the Bus Terminal range offers a wide range of sam- pling options. The type and duration of the pulse is decisive for the selec- tion of the correct Bus Terminal: The KL140x has a 3 ms input lter. The KL1232 extends very short pulses to 100 ms; the input lter is 0.2 ms. The KL1512 is an up/down coun- ter with an input lter of 0.2 ms. The pulses are processed based on standard function blocks such as trigger and counter. M-Bus counters can be con- nected via level converters to a serial interface. TwinCAT offers a software library with function blocks for com- mon M-Bus counters. The KL3681 multimeter terminal can be used to measure currents and voltages directly in the control system. The TwinCAT Scope enables curve display in real-time. Ethernet Current Gas Water New Automation Technology BECKHOFF We reserve the right to make technical changes. 19 Process operating and monitoring are key functions in building automation. The specic requirements vary depending on the building type and function, and the building manage- ment, automation and eld levels deal with a wide range of different tasks. Standard tech- nologies such as Ethernet TCP/IP enable unrestricted system-wide access to all devices. Beckhoff Building Automation | Operating and monitoring New Automation Technology We reserve the right to make technical changes. BECKHOFF 20 Building management (management level) Based on standard PC and IT tech- nology as operating and monitoring platform, the control system is able to meet the requirements of any SCADA system. A comprehensive range of IPCs with remote DVI/USB panels or Panel PCs, optionally with or without touch display, is avail- able as hardware platform. Beckhoff offers standard communication inter- faces to match any SCADA system. Local plant operation (automation level) Control Panels with touch display and/or integrated keyboard enable to access local system components. The use of Ethernet Panels/Embedded PCs enables web-based control via the integrated web server. PLC and the vis- ualisation can run on the same device. Room control (eld level) The control system is precisely adapted to the requirements at the eld level. Control Panels with touch display between 5.7 and 24 are available. Commercially available operating devices can be integrated via standard interfaces. connection of switches and sensors via 24 V DC or 230 V AC integration of compact room control units via EIB, LON, Modbus TCP, Modbus RTU connection of radio equipment via EnOcean Beckhoff offers a comprehensive hardware portfolio in the form of Bus Terminals and PC interfaces for inte- grating sensors and actuators. Soft- ware libraries for EIB, LON, Modbus, EnOcean and serial communication round off the portfolio. Ethernet New Automation Technology BECKHOFF We reserve the right to make technical changes. 21 Beckhoff Building Automation | Home automation Similar to the automation found in larger buildings, all data points required for home auto- mation are connected directly to the Beckhoff Bus Terminal system. A wide range of dif- ferent Bus Terminals enables integration of all sensors and actuators for lighting control, energy consumption metering and garden irrigation, for example, as a function of data from a weather station. New Automation Technology We reserve the right to make technical changes. BECKHOFF 22 DALI Local I/O stations distributed throughout the home are networked with the central Embedded DIN rail PC via Ethernet. The standard Ethernet network is used for PCs, telephones, home entertainment and building control tasks. Building control functions can be displayed and operated via Beckhoff Control Panels with touch screen distributed throughout the house. Building status messages can be retrieved via SMS, video, voice or e-mail. On the software side, TwinCAT automation software is the core of the home automation system. It can be used to congure a wide range of building functions. Ethernet New Automation Technology BECKHOFF We reserve the right to make technical changes. 23 24 References Beckhoff Building Automation enables the simple integration of IT and automation worlds in the control of industrial and ofce buildings. The product range consists of a univer- sal, scalable, modular control system that offers suitable solutions for any task: from power ful Industrial PCs as building computers to local Ethernet controllers that record and pre-process signals directly and locally. Ethernet as a universal communication system connects the data worlds of ofce and building automation. Our partners realise numerous objects worldwide on the basis of this control platform. The following selection of example solutions illustrates that there are no limits, from the automation of individual systems to fully integrated building automation. New Automation Technology BECKHOFF 25 Microsoft, Cologne, Germany Schco Technology Center, Bielefeld, Germany Eurotheum (European Central Bank), Frankfurt, Germany New Automation Technology We reserve the right to make technical changes. BECKHOFF 26 References | Ofce buildings Microsoft, Unterschleiheim near Munich, Germany WesBank, Johannesburg, South Africa KlnTriangle, Cologne, Germany Allianz head ofce, Stuttgart, Germany | BSH Bosch und Siemens Hausgerte GmbH at Aviva, Munich, Germany | Ofce building Esplanade Theresienhhe, Munich, Germany | Fortis Bank, Brussels, Hasselt, Belgium | Park Gate, Munich, Germany | Westpac headquarters, Sydney, Australia www. beckhoff.com/building Other references New Automation Technology BECKHOFF We reserve the right to make technical changes. 27 dSPACE, Paderborn, Germany Miele innovation centre for electronics development, Gtersloh, Germany New Automation Technology We reserve the right to make technical changes. BECKHOFF 28 References | Industrial buildings | Broschek Tiefdruck, Hamburg, Germany | Daimler, Stuttgart, Germany | Heroal, Verl, Germany | Liebherr Werk, Nenzig, Austria | Philip Morris International, Lausanne, Switzerland | SOLON SE, Berlin, Germany | ZF-Lemfrder Fahrwerk- technik, Dielingen, Germany F-eins, Vienna, Austria AMAG Automotive, Buch, Switzerland www. beckhoff.com/building Other references New Automation Technology BECKHOFF We reserve the right to make technical changes. 29 Dolder Grand Hotel, Zurich, Switzerland Tschuggen Bergoase, Arosa, Switzerland Aqua-Dom Hotel, Berlin, Germany New Automation Technology We reserve the right to make technical changes. BECKHOFF 30 References | Hotels | Grand Tirolia, Kitzbhel, Austria | Hotel Aviva, St. Stefan am Walde, Austria | Hotel Rasmushof, Kitzbhel, Austria | Leonardo Royal Hotel, Munich, Germany | Royal Spa Kitzbhel, Austria | St. Martins Therme, Frauenkirchen, Austria | Therme Laa, Laa an der Thaya, Austria Holiday Inn, Samara, Russia CitizenM Hotel, Amsterdam, Netherlands Hotel Aurelio, Lech, Austria Hotel Sonne, Mellau, Austria Hotel Krallerhof, Leogang, Austria www. beckhoff.com/building Other references New Automation Technology BECKHOFF We reserve the right to make technical changes. 31 Deutsches Museum, Munich, Germany Carr Theatre, Amsterdam, Netherlands New Automation Technology We reserve the right to make technical changes. BECKHOFF 32 References | Theatres and museums Scala di Milano, Milan, Italy www. beckhoff.com/building | Ronacher Theater, Vienna, Austria Charlottenburg Palace, Berlin, Germany Other references | Dresdner Stadtmuseum, Dresden, Germany | Gran Casino Aranjuez, Madrid, Spain New Automation Technology BECKHOFF We reserve the right to make technical changes. 33 | Allianz Arena, Munich, Germany | AUA Training Center, Schwechat, Austria | Europlaza, Vienna, Austria BKN Strobel, Holm, Germany ESPRIT arena, Dsseldorf, Germany Other references New Automation Technology We reserve the right to make technical changes. BECKHOFF 34 References | Infrastructure | Ferry Porsche Congress Center, Zell am See, Austria | Lufthansa Training Center, Schwechat, Austria | Metro M2, Lausanne, Switzerland | Nordtangente (ring road north), Basel, Switzerland | Stadtwerke Lingen, Germany | Steelworks, Bremen, Germany | University of Zurich, Switzerland | Zigong City Tower, Zigong, China Smart Tower, Kehl-Bodersweier, Germany Zentrum Zukunft, Emstek, Germany www. beckhoff.com/building Oncological Center, Samara, Russia Amsec, Hagenberg, Austria New Automation Technology BECKHOFF We reserve the right to make technical changes. 35 36 Beckhoff | Products and application examples The PC- and Ethernet-based control solution from Beckhoff is ideally suited for building automation due to its open interfaces based on IT and Windows standards. With the reso- lute application of Ethernet from the sensor/actuator level via the PC level to the manage- ment level, all building users share a common data network. This means, for example, that intelligent components such as operating panels can communicate directly with the higher-level PC controller via the network cabling. The Beckhoff Bus Terminal system for the interfacing of data points not only supports all common sensors and actuators, but also integrates all main bus systems via correspond- ing Bus Coupler types. With over 400 different Bus Terminals, Beckhoff offers the right technology for all data points. The retrotting of building functions is greatly simplied with the Bus Terminals. Subordinate subsystems such as EIB, LON, DALI, MP-Bus, M-Bus or RS232/RS485 serial interfaces can be integrated via communication Bus Terminals. New Automation Technology BECKHOFF 37 Beckhoff | Open control architecture Field level Management level Automation level Ethernet, ADS, BACnet/IP, OPC-UA, Modbus TCP, PROFINET ERP FMS Master computer D i g i t a l
i n p u t D i g i t a l
i n p u t D i g i t a l
o u t p u t D i g i t a l
o u t p u t A n a l o g
i n p u t A n a l o g
i n p u t A n a l o g
o u t p u t A n a l o g
o u t p u t Embedded PC, Bus Terminals Bus Coupler, Bus Terminals New Automation Technology We reserve the right to make technical changes. BECKHOFF 38 Ethernet Panel Bus Coupler, Bus Terminals Bus Coupler, Terminals Bus Coupler, Terminals Panel PC D i g i t a l
I / O D i g i t a l
I / O D i g i t a l
I / O D i g i t a l
I / O D i g i t a l
I / O A n a l o g
I / O A n a l o g
I / O A n a l o g
I / O A n a l o g
I / O A n a l o g
I / O R S 2 3 2 / R S 4 8 5 E I B P R O F I B U S P R O F I B U S M o d b u s L O N M - B u s P R O F I N E T M P - B u s E n O c e a n C A N o p e n D A L I D M X Embedded PC, Bus Terminals Embedded PC, Bus Terminals Bus Terminal Controller, Bus Terminals Embedded PC, EtherCAT Terminals New Automation Technology BECKHOFF We reserve the right to make technical changes. 39 Industrial PC Embedded PC Embedded PC Bus Terminal Controller Beckhoff | Scalable control technology Beckhoff offers a scalable, modular control system that provides suitable solutions for any task in terms of computing power, complexity and costs. Irrespective of their performance class, all Beckhoff controllers are programmed using the IEC 61131-3 standard programming languages via TwinCAT automation software. We reserve the right to make technical changes. 40 Universal software for all areas of application The TwinCAT software system is a versatile programming tool for all automation levels. integration of real-time control, multi PLC and programming environment executable under Windows NT/2000/XP/Vista, Windows 7, NT Embedded, Embedded Standard and CE connectivity to all popular eldbuses and PC interfaces use of open standards, such as OPC, OCX, DLL, etc. software PLC compliant with the IEC 61131-3 standard with up to 4 runtime systems per PC and short cycle times starting from 50 s efcient software engineering using software libraries for building automation high readability and expandability of the user programs by object-orientated function blocks Small local controller The Bus Terminal Controllers are suitable for use as zone controllers and for building areas in which a robust small controller is required. programmable IEC 61131-3 controller K-bus interface for connecting Beckhoff Bus Terminals direct wiring of sensors and actuators exchange of pre-processed data with the higher-level controller via the eldbus Zone and oor controller The Embedded PCs from the CX series are suitable for integral room automation, as oor controllers and for control tasks at automation level. combination of PLC, I/O connection and visualisation scalable performance compact design DIN rail mounting exible expandability by the addition of PC and eldbus interfaces as well as I/O components Master computer Industrial PCs from Beckhoff represent the most pow- erful hardware platform for PC-based control systems for the management and automation level in building automation applications. The PCs feature industrial design and are equipped with top-performance com- ponents. They are based on open IT and automation standards. A wide range of types and individual case designs enable optimum adaptation to the specic control requirements. In contrast to standard DDC technology, the system is not limited through xed data point specications for individual control. New Automation Technology BECKHOFF We reserve the right to make technical changes. 41 Head station of the Bus Terminals: Bus Couplers, Bus Terminal Controllers or Embedded PCs Bus Terminals in 1-, 2-, 4-, 8- and 16-channel modularity with mixing of any signal type; HD (High-Density) Bus Terminals with 16 con- nection points in a 12 mm housing for reducing space requirements and costs 3-phase power measurement terminal for the measurement of all relevant elec- trical data of the supply network Digital multi- meter terminal for the direct measurement of current and voltage Potential feed terminals for the congura- tion of differ- ent potential groups Universal dimmer terminals with automatic load detection for control of bright- ness values indepen dent of the eldbus Beckhoff | Bus Terminals The complete I/O system Ethernet The Beckhoff Bus Terminal system sup- ports all common sensors and actuators with 400 different I/O terminals. Bus Terminal Controller series BC with integrated IEC 61131-3 PLC Embedded PC series CX for PLC and Motion Control applications Embedded PC series CX with integrated eldbus slave Bus Coupler series BK, the link between Bus Terminals and eldbus New Automation Technology We reserve the right to make technical changes. BECKHOFF 42 Bus end terminal Terminal bus extension for the connection of up to 255 (instead of 64) Bus Terminals to a station TwinSAFE Bus Termi- nals for the connection of all com- mon safety sensors and actuators EnOcean master for receiving or sending sig- nals via radio transmission Pressure measuring terminals for the meas- urement of differential and absolute pressures Communica- tion terminals for the inte- gration of subsystems such as EIB, LON, DALI or RS232 More efcient manual/ emergency operation using Bus Terminals: switch or potentiometer in Bus Ter- minal format for process data change independent of the controller Bus Terminals with a maximum measuring error of 0.01% extend the range of applica- tions to high-preci- sion measurement technology. New Automation Technology BECKHOFF We reserve the right to make technical changes. 43 Beckhoff | Bus Terminals Application examples Ethernet KL2512 (LED) Output terminal for the direct connection of ohmic loads. The output signal is a pulse-width modulated voltage. KL2751/KL2761 (dimming) Dimmer terminals for the direct connection of lights with different loads (up to 600 VA); output protected against short circuit and overload KL3208-0010 (temperature measurement) Analog input terminal for the direct connection of 8 resistance sensors in two-wire technique LEDs indicate the four output bits from the process data and cannot be activated directly via the switches. KM1644 (4-channel manual operation) The digital KM1644 input terminal is used for manual input direct- ly in the process data. The 4 switches supply their status to the con- trol system as digital bit information. The four KM2642 (relay with manual/auto- matic operation) Digital output terminal with two independ- ent relay changeover contacts for switching mains current consumers (230 V AC, 6 A); change- over between automatic and manual operation via integrated switch KL6811 (DALI) DALI master terminal for the control of elec- tronic operating devices, such as uorescent lamps, emergency lighting, occupancy sensors or brightness sensors H V A C L i g h t i n g exible lighting control for chang- ing conditions, e.g. changes in room layout connection of up to 64 DALI slaves integrated 24 V DC power supply unit New Automation Technology We reserve the right to make technical changes. BECKHOFF 44 KL2602 (switching) 2-channel relay output terminal with a single contact per relay for switching mains voltage con- sumers up to 230 V AC KL6771 (MP-Bus master terminal) MP-Bus terminal for the direct connection of up to 8 MP-Bus devices and 8 sensors; commission- ing or conguration via IEC 61131-3 function blocks KM4602 (manual/automatic operation) Analog output terminal with two potential- free 0 to 10 V outputs; changeover between automatic and manual operation via integrated switch KL4404 (constant actuators) Analog output terminal generates signals within a range of 0 to 10 V; suitable for the control of constant actuators such as valves. KL3464 (analog input) Analog input terminal processes signals within the range of 0 to 10 V; suitable e.g. for the connection of poten- tiometers, weather stations, etc. KM3701/KM3712 (pressure measurement) The KM3701 measures pressure differences between two hose con- nections. The KM3712 measures two negative pressure values at the hose connections. EL6851/EL6851-0010 (EtherCAT DMX master/slave) EL6851 DMX master terminal: connection of max. 32 devices without repeater transmission of up to 512 bytes of data use of the RDM (Remote Device Management) protocol EL6851-0010 DMX slave terminal: reception of up to 64 bytes of data start address and data length adjustable via CoE objects (CAN application protocol over EtherCAT) The DMX slave receives data from the DMX mas- ter and makes it avail- able to the application via EtherCAT. New Automation Technology BECKHOFF We reserve the right to make technical changes. 45 Beckhoff | Bus Terminals Application examples Ethernet KL6581, KL6583/ KL6021-0023, KL6023 (EnOcean) KL6583 for transmitting and receiving EnOcean telegrams; KL6581 for the connection of up to 8 KL6583 modules; KL6021-0023 for receiv- ing EnOcean telegrams; KL6023 wireless adapter KL6401 (LON Bus Terminal) The LON Bus Terminal supports 170 SNVTs (Standard Network Variable Types), which are arbitrarily adjustable. 62 SNVTs can be cong- ured per terminal. KL6301 (EIB Bus Terminal) The EIB Bus Termi- nal supports up to 256 group addresses. With up to 8 lters, it allows the deni- tion of the telegrams relevant to the Beckhoff controller; maximum length per lter: 64 subgroups. KL6001/31, KL6021/41 (serial communica- tion RS232/RS485) Bus Terminals for the connection of devices with serial interface, e.g.: displays modem connection for remote mainte- nance or diagnostics connection of M-bus devices L o g g i n g
o f
e n e r g y
d a t a C o m m u n i c a t i o n KL3681 (digital multimeter) Bus Terminal for meas- uring currents and voltages; read-out and further processing of the measured values with conventional eldbuses KL1501 (counter) Bus Terminal for count- ing binary pulses switchable between upward and down- ward counting KL3403 (energy measurement) Bus Terminal for the measurement of all relevant electrical data of the mains supply triggerable via the gate connection implementation of two counters (16 bits) via the Clock1 input New Automation Technology We reserve the right to make technical changes. BECKHOFF 46 KL1362 (break-in sensors) The digital input termi- nal analyses the input signals of break-in sen- sors with the aid of a current loop. Alarm con- tacts with a xed resist- ance ratio are monitored safely. KL2722 (blind) The output terminal uses a power switch to con- trol mains voltage from 12 V to 230 V; direct connection of AC blind motors with reversal of the direction of rotation is possible. KL/EL/KM1xxx Digital inputs from 5 V DC to 230 V AC, e.g. for the connection of motion detectors, buttons, window and door contacts, occu- pancy sensors, etc. KL/EL/KM2xxx Digital outputs from 5 V DC to 230 V AC, 16 A, e.g. for switching and controlling light- ing, valves, fans, pumps, power sockets, etc. KL/EL/KM3xxx Analog inputs from 0 to 10 V and 4 to 20 mA up to resis- tance measurement, e.g. for the connection of weather stations, temperature sensors, air quality sensors, etc. KL/EL/KM4xxx Analog outputs from 0 to 10 V up to 4 to 20 mA, for controlling constantly controlled valves, ventilation aps, speed controlled pumps, etc. G e n e r a l F a c a d e KL2542 (DC motor) Bus Terminal for the direct operation of two DC motors specication of speed or position of the automation device via a 16-bit value output stage protected against overload and short circuit Digital input Digital output Analog input Analog output New Automation Technology BECKHOFF We reserve the right to make technical changes. 47 Beckhoff | TwinCAT The universal automation software platform High-end PLC international IEC 61131-3 programming standard reusable software modules can be used almost unlimited memory no restrictions in terms of number of blocks and variables minimum PLC cycle times through native code generation high-speed software solutions for controllers, etc. up to four run-time systems per PC, up to four tasks per run-time system Solutions can be provided for all areas of building automation with the aid of the TwinCAT universal software tool. The extensive software libraries and supplements, which considerably simplify engineering, continue the concept of the modular Beckhoff automation components at software level as well. TwinCAT system architecture TCP/ IP | serial ADS interface System Manager Real-time server I/O mapping I/O: all fieldbuses and PC interfaces ADS Message router Message router I/O ADS interface I/O server I/O run-time I/O ADS interface PLC server PLC run-time I/O ADS interface NC PTP server NC PTP run-time I/O ADS interface NC I server NC I run-time I/O ADS interface CNC server CNC run-time System Manager configuration, service, monitoring ADS PLC control PLC programming ADS ADS Motion Control TwinCAT NC PTP TwinCAT NC I TwinCAT CNC ADS OCX/DLL Scada, Visual Basic, Delphi, Visual C++, .NET, C#, VB.NET, OPC client Scada, Visual Basic, Delphi Internet /Intranet DA XML UA TwinCAT OPC server New Automation Technology We reserve the right to make technical changes. BECKHOFF 48 Beckhoff TwinCAT ADS communication interface universal, vertical, horizontal cyclical/event-driven data exchange and/or commands open protocol with example code available on Windows operating systems access from the PLC via function block components free of charge: OCX/DLL/.NET/Script/Webservice Transparency via ADS, continuous routing via: local/network UDP/TCP/serial/Bluetooth/Fieldbus/ EtherCAT/SOAP (HTTP) TwinCAT network variables publisher/subscriber variables via broadcast, multicast or unicast Automation/industrial/IT protocols TwinCAT supports all common standards. TwinCAT Supplements Software modules for TwinCAT that offer PC features for the PLC programmer: Building Automation Framework ADS Communication Library OPC Server Modbus Server TCP/IP Connection Server XML Data Server SMS/SMTP Server Database Server Visualisation PLC HMI PLC HMI Web etc. New Automation Technology BECKHOFF We reserve the right to make technical changes. 49 Beckhoff | Worldwide New Automation Technology We reserve the right to make technical changes. BECKHOFF 50 New Automation Technology BECKHOFF We reserve the right to make technical changes. 51 Beckhoff | Worldwide support and service Worldwide support and service contacts: www. beckhoff.com/support Beckhoff and its partners around the world offer comprehensive support and service, guaranteeing fast and competent assistance with all questions related to Beckhoff products and system solutions. Beckhoff offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with wide-ranging services: worldwide support design, programming and commissioning of complex automation systems training program for Beckhoff system components The Beckhoff service center supports you in all matters of after-sales service: 24-hour service spare parts service worldwide service on-site service Beckhoff support and service are available to you wherever you are in the world, and can be reached by telephone, fax or e-mail. The contact addresses for your country can be found in the list of Beckhoff branches and partner companies. Beckhoff Support Beckhoff Service New Automation Technology We reserve the right to make technical changes. BECKHOFF 52 Beckhoff | Information Media www. beckhoff.com/media Product overview Product DVD News catalog Order no. DK130x Order no. DK140x Order no. DK4000 Main catalog Order no. DK110x Ordering information Description DK1101 Main catalog, German DK1102 Main catalog, English DK1301 News catalog, German DK1302 News catalog, English DK1401 Product overview, German DK1402 Product overview, English DK1405 Product overview, French DK1406 Product overview, Italian DK1407 Product overview, Russian DK1409 Product overview, Turkish DK4000 Main catalog and software products on DVD, German, English, Italian New Automation Technology BECKHOFF We reserve the right to make technical changes. 53 Beckhoff | www.beckhoff.com/building The online manual The Beckhoff Information System contains a wide range of useful infor- mation about the Beckhoff products, including not only an overview of the products and relevant documentation, but also technical information, manuals, TwinCAT example codes, a knowledge base and much more. Products online At www.beckhoff.com you can get detailed information on the range of products from Beckhoff. Animations, videos and interac- tive online presentations supplement the large variety of information. Print media online The Beckhoff catalogs and yers are available for download on the Internet. Printed copies are available on request. Please use our online order form to specify your requirements. www. beckhoff.com/news http://infosys.beckhoff.com www. beckhoff.com New Automation Technology We reserve the right to make technical changes. BECKHOFF 54 Picture credits: Schco International KG (pages 1, 6, 811, 1416, 26) The Dolder Grand, Zurich, photographer: Stefan Schmidlin (pages 4, 30) Beckhoff
, TwinCAT
, EtherCAT
, Safety over EtherCAT
, TwinSAFE
and XFC
are registered trademarks of and licensed by Beckhoff Automation GmbH.
Other designations used in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owners. Beckhoff Automation GmbH 04/2010 The information provided in this brochure contains merely general descriptions or characteristics of performance which in case of actual application do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressively agreed in the terms of contract. Online documentation In addition to all the information contained in the printed catalog, the online service offers additional information, available in the universal PDF or in CHM (Compiled HTML) le format: detailed documentation and manuals for the Beckhoff products and software updates, technical drawings and conguration les for the eldbus components. Beckhoff Newsletter Beckhoff offers a further information service with the New Automation Technology Newsletter. Alongside printed and online media, customers and prospective customers can keep up to date quickly and simply via electronic mail. Beckhoff RSS feeds deliver the latest news directly to PCs or Smartphones. The full version of the powerful TwinCAT automation software can be downloaded and tested free of charge for 30 days. www. beckhoff.com/documentations www. beckhoff.com/TwinCAT www. beckhoff.com/newsletter New Automation Technology BECKHOFF We reserve the right to make technical changes. 55 D K 3 5 0 2 - 0 4 1 0 Ofce Wuhan Beckhoff Automation (Shanghai) Co. Ltd. Room 1803, 18/F., Wuhan Zhongshang Plaza, NO.7, Zhongnan Road, Wuhan, Hubei P.R. China Phone: + 86 27 / 81 34 87 15 wuhan@beckhoff.com.cn India Beckhoff Automation Pvt. Ltd. Suite 4, Level 6, Muttha Towers Don Bosco Marg Pune 411 006 India Phone: + 91 20 / 40 00 48 00 info@beckhoff.co.in www.beckhoff.co.in Inteltek Automation Pvt. Ltd. Sr.no.100/5, Ambegaon Pune 411 046 Maharashtra India Phone: + 91 20 / 24 31 81 21 info@inteltekindia.com www.inteltekindia.com Japan K.MECS Co., Ltd. Yusen Iwamotocho Blg. 3F 2-3-3 Iwamotocho, Chiyoda-City, Tokyo 101-0032 Japan Phone: + 81 3 5825 5333 info@kmecs.co.jp www.kmecs.com Lebanon, Jordan, Syria Industrial Technologies (itec) S.A.L. Afrah Plaza Center, Blvd Fouad Chehab Sin El Fil, Beirut Lebanon Phone: + 961 (1) 49 11 61 info@iteclb.com www.iteclb.com Singapore, Malaysia, Philippines, Vietnam, Indonesia TDS Technology (S) Pte Ltd. 64 Sungei Kadut Loop (Hocen Building) Singapore 729493 Singapore Phone: + 65 / 63 66 16 61 sales_sg@tdstech.com www.tdstech.com Thailand TDS Technology (Thailand) Co., Ltd. 50/962 Moo 2 Bengyeetos Thanyaburi Pratumthanee 12130 Bangkok Thailand Phone: + 66 (0) 2569 5511 sales_th@tdstech.com www.tdstech.com T & R Electronic (Thailand) Co., Ltd. 120/62 Moo 8 Bang Sare Sattahip Chonburi 20250 Thailand Phone: + 66 (0) 3873 7487 trthailand@trelectronic.co.th www.trelectronic.co.th South Korea Tri-TEK Corp. 717 DaeRyung TechnoTown III 448 KasanDong Kumcheongu Seoul 153-803 Korea Phone: + 82 2 / 2107-32 42 tritek@tritek.co.kr www.tritek.co.kr Taiwan JI-DIEN Co., Ltd. 9F., No. 22, Sec. 1, Zhongshan Rd. Xingzhuang City Taipei County 242 Taiwan (R.O.C.) Phone: + 886 (2) 8522 3237 jidien@chgroup.com.tw www.chgroup.com.tw United Arab Emirates, Oman, Qatar, Bahrain, Kuwait, Saudi Arabia Beckhoff Automation FZE C# 608, Dubai Silicon Oasis P.O. Box No. 341007 Dubai United Arab Emirates Phone: + 971 4 5015480 info@beckhoff.ae www.beckhoff.ae Australia Australia Beckhoff Automation Pty. Ltd. Level 16, 10 Queens Road Melbourne, Victoria, 3004 Australia Phone: + 61 (3) 99 12 54 30 info@beckhoff.com.au www.beckhoff.com.au New Zealand CSE-W. Arthur Fisher Ltd P.O. Box 58955 Botany Manukau 2163 New Zealand Phone: + 64 9 271 3810 sales@cse-waf.co.nz www.cse-waf.co.nz www.beckhoff.com Headquarters Beckhoff Automation GmbH Eiserstrae 5 33415 Verl Germany Phone: + 49 (0) 52 46 / 9 63 - 0 info@beckhoff.de www.beckhoff.de Europe Germany Ofce Balingen Beckhoff Automation GmbH Karlstrae 19 72336 Balingen Germany Phone: + 49 (0) 74 33 / 2 60 24 - 0 balingen@beckhoff.de Ofce Berlin Beckhoff Automation GmbH Fasanenstrae 81 10623 Berlin Germany Phone: + 49 (0) 30 / 88 71 16 - 0 berlin@beckhoff.de Ofce Frankfurt Beckhoff Automation GmbH Torhaus Westhafen Speicherstrae 59 60327 Frankfurt am Main Germany Phone: + 49 (0) 69 / 68 09 88 - 0 frankfurt@beckhoff.de Ofce Hanover Beckhoff Automation GmbH Podbielskistrae 342 30655 Hanover Germany Phone: + 49 (0) 5 11 / 87 57 58 - 0 hannover@beckhoff.de Ofce Lbeck Beckhoff Automation GmbH Wahmstrae 56 23552 Lbeck Germany Phone: + 49 (0) 4 51/ 20 39 88 - 0 luebeck@beckhoff.de Ofce Munich Beckhoff Automation GmbH Oppelner Strae 5 82194 Grbenzell/Munich Germany Phone: + 49 (0) 81 42 / 4 10 59 - 0 muenchen@beckhoff.de Ofce Nuremberg Beckhoff Automation GmbH Ostendstrae 196 90482 Nuremberg Germany Phone: + 49 (0) 9 11 / 5 40 56 - 0 nuernberg@beckhoff.de Sales Ofce Ravensburg Beckhoff Automation GmbH Parkstrae 48 88212 Ravensburg Germany Phone: + 49 (0) 7 51 / 3 54 15 50 ravensburg@beckhoff.de Ofce Rhein/Ruhr Beckhoff Automation GmbH Eurotec-Ring 7 47445 Moers Germany Phone: + 49 (0) 28 41/ 9 08 16 - 6 rhein-ruhr@beckhoff.de Austria Headquarters Beckhoff Automation GmbH Hauptstrae 4 6706 Brs Austria Phone: + 43 (0) 55 52 / 6 88 13 - 0 info@beckhoff.at www.beckhoff.at Sales Ofce Obersterreich Beckhoff Automation GmbH Softwarepark 35 4232 Hagenberg Austria Phone: + 43 (0) 72 36 / 2 09 25 - 0 oberoesterreich@beckhoff.at Sales Ofce Niedersterreich Beckhoff Automation GmbH Leobersdorferstrae 42 2560 Berndorf Austria Phone: + 43 (0) 26 72 / 8 20 34 niederoesterreich@beckhoff.at Sales Ofce Tirol Beckhoff Automation GmbH Klammstrae 66 / 39 6020 Innsbruck Austria Phone: + 43 (0) 512 / 236 043 tirol@beckhoff.at Belgium, Luxembourg Beckhoff Automation BVBA Kempische Steenweg 305 bus 202 3500 Hasselt Belgium Phone: + 32 (0) 11 / 24 08 00 info@beckhoff.be www.beckhoff.be Multiprox N.V. Lion drweg 12 P.b. 71 9300 Aalst Belgium Phone: + 32 (0) 53 / 76 65 66 info@multiprox.be www.multiprox.be Bulgaria Kastiva GmbH 68-72 Ami Bue Str., 4. Floor 1612 Soa Bulgaria Phone: + 3 59 (2) 9 50 44 31 ofce@kastiva.com www.kastiva.com Croatia Krovel d.o.o. Barutanski jarak 114 10000 Zagreb Croatia Phone: + 3 85 / 16 11 77 20 beckhoff@krovel.hr www.krovel.hr Czech Republic, Slovac Republic Dyger s.r.o. Vystaviste 1 648 59 Brno Czech Republic Phone: + 420 5 / 41 32 10 04 info@dyger.cz www.dyger.cz Denmark Headquarters Beckhoff Automation ApS Naverland 2 2600 Glostrup Denmark Phone: + 45 43 / 46 76 20 info@beckhoff.dk www.beckhoff.dk Ofce Hobro Beckhoff Automation ApS Majsmarken 1 9500 Hobro Denmark Phone: + 45 76 / 36 38 31 info@beckhoff.dk Ofce Kolding Beckhoff Automation ApS Birkemose all 25 6000 Kolding Denmark Phone: + 45 76 / 31 20 72 info@beckhoff.dk Finland, Estonia Headquarters Beckhoff Automation Oy P.O. Box 23 Kankurinkatu 4-6 05801 Hyvink Finland Phone: + 358 (0) 20 / 7 42 38 00 info@beckhoff. www.beckhoff. Sales Ofce Seinjoki Beckhoff Automation Oy Tiedekatu 2 60320 Seinjoki Finland Phone: + 358 (0) 20 / 7 42 38 50 info@beckhoff. Sales Ofce Tampere Beckhoff Automation Oy Hermiankatu 1 B 33720 Tampere Finland Phone: + 358 (0) 20 / 7 42 38 70 info@beckhoff. France Headquarters Beckhoff Automation Sarl Immeuble Le Montral ZA de Courtaboeuf 19 bis, avenue du Qubec 91951 Courtaboeuf Cedex France Phone: + 33 (0) 1 69 29 83 70 info@beckhoff.fr www.beckhoff.fr Sales Ofce Neuville en Ferrain Beckhoff Automation Sarl 28, Rue de Tourcoing 59960 Neuville en Ferrain France Phone: + 33 (0) 3 20 11 00 08 info@beckhoff.fr Greece, Cyprus L. J. Skourgialos Industrial Automation Systems 241 EL. Venizelou 176 73 Kallithea /Athens Greece Phone: + 30 / 21 09 51 02 60 ias@otenet.gr Hungary Controrg Kft. Pajta u. 14 8200 Veszprem Hungary Phone: + 36 / 88 42 40 75 info@controrg.hu www.controrg.hu Italy Headquarters Beckhoff Automation S.r.l. Via E. Majorana, 1 20054 Nova Milanese (MI) Italy Phone: + 39 03 62 / 36 51 64 info@beckhoff.it www.beckhoff.it Ofce Bologna Beckhoff Automation S.r.l. Via Zanini, 7 40011 Anzola dellEmilia (BO) Italy Phone: + 39 05 1 / 73 15 09 bologna@beckhoff.it Ofce Padua Beckhoff Automation S.r.l. Via Alsazia, 3/B 35127 Padua (PD) Italy Phone: + 39 0 49 / 8 70 48 38 padova@beckhoff.it Lithuania, Latvia, Belarus Santavilt UAB Taikos 149 52119 Kaunas Lithuania Phone: + 3 70 37 / 35 01 66 info@santavilte.lt www.santavilte.lt Netherlands Industrial Automation Link Kppersweg 71 2031 EB Haarlem Netherlands Phone: + 31 23 / 5 18 51 40 sales@ial.nl www.ial.nl Norway Beckhoff Automation AS Trleborgodden 6 3112 Tnsberg Norway Phone: + 47 33 50 46 90 info@beckhoff.no www.beckhoff.no Poland Beckhoff Automation Sp. z o.o. Stara Iwiczna, ul. Sloneczna 116A 05-500 Piaseczno Poland Phone: + 48 22 / 7 57 26 10 info@beckhoff.pl www.beckhoff.pl Portugal Bresimar Automao, S.A. Quinta do Simo EN109 Esgueira Apartado 3080 3801-101 Aveiro Portugal Phone: + 351 234 / 30 33 20 bresimar@bresimar.pt www.bresimar.pt Romania Kreatron Automation S.R.L. Str. Octavian Fodor nr. 113, ap. 13 400434, Cluj-Napoca jud. Cluj Romania Phone: + 40 264 / 48 47 08 ofce@kreatron.ro www.kreatron.ro Russia Headquarters Beckhoff Automation OOO Ul. Bakuninskaya 14, Building 9 105005 Moscow Russia Phone: + 7 495 / 9 81 64 54 russia@beckhoff.com www.beckhoff.ru Representation North-West Federal District Beckhoff Automation GmbH V.O., 7-ya Liniya, 76, Ofce 620 199178 Saint-Petersburg Russia Phone: + 7 812 / 332 62 05 north-westfo@beckhoff.ru Representation Ural Federal District Beckhoff Automation GmbH Uliza Komsomolskaya 37, Ofce 402/4 620049 Ekaterinburg Russia Phone: + 7 3 43 / 3 79 98 73 uralfo@beckhoff.ru Representation Volga Federal District Beckhoff Automation GmbH Krasnoarmayskaya ul.1, Ofce 312 443010 Samara Russia Phone: + 7 846 / 2 69 80 67 volgafo@beckhoff.ru Slovenia Beckhoff Avtomatizacija d.o.o. Zbiljska cesta 4 1215 Medvode Slovenia Phone: + 3 86 / 13 61 30 80 info@beckhoff.si www.beckhoff.si Spain Headquarters Beckhoff Automation S.A. Edicio Testa Sant Cugat Avda. Alcalde Barnils, 64-68 08174 Sant Cugat (Barcelona) Spain Phone: + 34 93 / 5 84 49 97 info@beckhoff.es www.beckhoff.es Sales Ofce Bilbao Beckhoff Automation S.A. Edicio Udondo C. Ribera de Axpe, no 50 4a planta, Ocina 4-5 48950 Erandio (Bilbao) Spain Phone: + 34 94 / 4 31 40 75 info@beckhoff.es Sales Ofce Madrid Beckhoff Automation S.A. Edicio Cimaga Sierra de Cazorla, 1 Planta Baja, Ocina E 28290 Las Matas (Madrid) Spain Phone: + 34 91 / 6 36 43 57 madrid@beckhoff.es Sweden Headquarters Beckhoff Automation AB Stenldersgatan 2A 21376 Malm Sweden Phone: + 46 (0) 40 / 6 80 81 60 info@beckhoff.se www.beckhoff.se Sales Ofce Danderyd Beckhoff Automation AB Enebybergsvgen 10B 18236 Danderyd Sweden Phone: + 46 (0) 8 / 4 46 30 00 info@beckhoff.se Sales Ofce Vrnamo Beckhoff Automation AB Vstbovgen 53 33153 Vrnamo Sweden Phone: + 46 (0) 40 / 6 80 81 60 info@beckhoff.se Switzerland Headquarters Beckhoff Automation AG Rheinweg 9 8200 Schaffhausen Switzerland Phone: + 41 (0) 52 / 6 33 40 40 info@beckhoff.ch www.beckhoff.ch Ofce Zurich Beckhoff Automation AG Felsenrainstrasse 1 8052 Zurich Switzerland Phone: + 41 (0) 52 / 633 40 40 info@beckhoff.ch Ofce Derendingen Beckhoff Automation AG Application/Software Development Hauptstrasse 39 4552 Derendingen Switzerland Phone: + 41 (0) 32 / 682 04 28 info@beckhoff.ch Sales + Support Center Suisse Romande Beckhoff Automation AG En Chamard 35 1442 Montagny-prs-Yverdon Switzerland Phone: + 41 (0) 24 / 447 27 - 00 yverdon@beckhoff.ch Support Center Ticino p.project sagl Via Pianella 19 6596 Gordola Switzerland Phone: + 41 (0) 91 / 745 01 11 ticino@beckhoff.ch Turkey Beckhoff Otomasyon ltd. ti. Gardenya-3 Plaza No: 18-19 34758 Ataehir Istanbul Turkey Phone: + 90 216 580 9830 info@beckhoff.com.tr www.beckhoff.com.tr UK, Ireland Beckhoff Automation Ltd. The Boathouse Station Road Henley-on-Thames Oxon RG9 1AZ Great Britain Phone: + 44 14 91 / 41 05 39 info@beckhoff.co.uk www.beckhoff.co.uk North America USA Headquarters and Training Center Beckhoff Automation LLC 12150 Nicollet Avenue South Burnsville, MN 55337 USA Phone: + 1 952 / 890 0000 beckhoff.usa@beckhoff.com www.beckhoffautomation.com East Region Headquarters and Training Center Beckhoff Automation LLC Charlotte, NC USA Phone: + 1 704 / 910 4367 east.usa@beckhoff.com East Region Sales Beckhoff Automation LLC Coplay, PA USA Phone: + 1 952 / 212 6226 newengland@beckhoff.com Beckhoff Automation LLC Hanover, PA USA Phone: + 1 717 / 634 5536 northeast.sales@beckhoff.com Beckhoff Automation LLC Canton, MI USA Phone: + 1 248 / 230 8835 michigan@beckhoff.com Beckhoff Automation LLC Medina, OH USA Phone: + 1 330 / 725 2403 mideast.usa@beckhoff.com Beckhoff Automation LLC Lake Wylie, SC USA Phone: + 1 803 / 746 5491 east.usa@beckhoff.com Beckhoff Automation LLC Apex, NC USA Phone: + 1 919 / 367 0349 southeast.usa@beckhoff.com Central Region Sales and Training Center Beckhoff Automation LLC Fond du Lac, WI USA Phone: + 1 920 / 929 0655 wisconsin@beckhoff.com Central Region Sales Beckhoff Automation LLC Burnsville, MN 55337 USA Phone: + 1 952 / 808 6513 north.usa@beckhoff.com Beckhoff Automation LLC Lemont, IL USA Phone: + 1 630 / 631 8467 midwest.usa@beckhoff.com Beckhoff Automation LLC Rogers, AR USA Phone: + 1 479 / 925 2951 south.usa@beckhoff.com Beckhoff Automation LLC Cedar Park, TX USA Phone: + 1 512 / 250 9809 southwest.sales@beckhoff.com Beckhoff Automation LLC Justin, TX USA Phone: + 1 817 / 428 5314 southwest.sales@beckhoff.com West Region Sales Beckhoff Automation LLC San Diego, CA USA Phone: + 1 858 / 546 1111 west.sales@beckhoff.com Beckhoff Automation LLC La Crescenta, CA USA Phone: + 1 818 / 224 9065 losangeles@beckhoff.com Beckhoff Automation LLC San Jose, CA USA Phone: + 1 408 / 823 3962 n.california@beckhoff.com Beckhoff Automation LLC Phoenix, AZ USA Phone: + 1 602 / 354 0506 arizona@beckhoff.com Beckhoff Automation LLC Arvada, CO USA Phone: + 1 303 / 429 0758 mountain.sales@beckhoff.com Beckhoff Automation LLC Mill Creek, WA USA Phone: + 1 425 / 451 4444 northwest.sales@beckhoff.com West Region Technical Center Beckhoff Automation LLC San Diego, CA USA Phone: + 1 858 / 546 1111 west.application@beckhoff.com Canada Headquarters Sales, Training Center and Application Development Beckhoff Automation Canada Ltd. 130 Research Lane Guelph, ON N1G 5G3 Canada Phone: + 1 905 / 852 1534 canada@beckhoff.com Canada Sales Beckhoff Automation Canada Ltd. London, ON Canada Phone: + 1 519 / 451 8572 canada@beckhoff.com Mexico Mexico Sales and Application Development Integra Automation, SA de CV Av. Industrias 325-A 78399 Fracc. Talleres San Luis Potos, S.L.P. Mxico Phone: + 52 444 / 822 2615 al 17 mexico@beckhoff.com Central and South America Argentina eFALCOM Alcorta 2411 CPA B1744HFM Moreno / Buenos Aires Argentina Phone: + 54 237 / 463 1151 info@efalcom.com www.efalcom.com Brazil Headquarters Beckhoff Automao Industrial Ltda. Rua Continental, 146 So Bernardo do Campo So Paulo 09750-060 Brazil Phone: + 55 (11) 4126-3232 info@beckhoff.com.br www.beckhoff.com.br Sales Ofce Campinas Beckhoff Automao Industrial Ltda. Edifcio Empresarial Torre do Castelo Rua Francisco Otaviano, 60 Sala 94 Bairro Chapado Campinas 13070-056 SP Brazil Phone: + 55 (19) 3368-7288 info@beckhoff.com.br Chile Tecmel Chile S.A. Padre Orellana 1486 Santiago Chile Phone: + 562 / 596 2541 mberrios@tecmelchile.cl www.tecmelchile.cl Costa Rica, Nicaragua, Honduras, El Salvador, Guatemala, Belize, Panama TAAC S.A. 50 Sur Hotel Grano de Oro Calle 30, Avenidas 4-6 San Jos 10103 Costa Rica Phone: + 506 / 2222-6450 info@taac-sa.com www.taac-sa.com Uruguay Comando Ltda. Dr. J. de Salterain 1142 Montevideo 11200 Uruguay Phone: + 598 (2) / 400-7923 comando@comandonet.com www.comandonet.com Africa Egypt Industrial Control Systems ICS 29 Dr. Mohamed El Harouny Street Nasr City, Cairo 11371 Egypt Phone: + 20 2 / 2 75 50 31 info@ics-me.com www.ics-me.com South Africa Beckhoff Automation (Pty) Ltd Unit 8, Boskruin Business Park, Randpark Ridge Randburg 2188 South Africa Phone: + 27 (0) 11 792 3374 info@beckhoff.co.za www.beckhoff.co.za Asia China Headquarters Beckhoff Automation (Shanghai) Co. Ltd. 5 th Floor, No. 163 JiangChang San Road Shanghai Shibei Industrial Zone Shanghai, 200436 P. R. China Phone: + 86 21 / 66 31 26 66 info@beckhoff.com.cn www.beckhoff.com.cn Ofce Beijing Beckhoff Automation (Shanghai) Co. Ltd. Room 1801-1803, Tower T3, Xihuan Plaza, No.1, Xizhimenwai Avenue Xicheng District Beijing, 100044 P. R. China Phone: + 86 10 / 58 30 12 36 beijing@beckhoff.com.cn Ofce Chengdu Beckhoff Automation (Shanghai) Co. Ltd. 8F, G of The City Tower, No. 86, Section one, South Peoples Road Chengdu, Sichuan, 610016 P. R. China Phone: + 86 28 / 86 20 25 81 chengdu@beckhoff.com.cn Ofce Guangzhou Beckhoff Automation (Shanghai) Co. Ltd. Room 4118-4119 Yaozhong Plaza 9 West Linhe Road Tianhe District Guangzhou, 510620 P. R. China Phone: + 86 20 / 38 01 03 00 guangzhou@beckhoff.com.cn