0 evaluări0% au considerat acest document util (0 voturi)
102 vizualizări6 pagini
This document contains specifications for cement type I and fly ash. For cement type I, it lists maximum allowable chemical and physical property limits. It also specifies minimum strength requirements at various ages. For fly ash, it lists minimum chemical composition requirements and physical performance requirements when used as a cement replacement. The document provides reference standards for both cement and fly ash specifications.
This document contains specifications for cement type I and fly ash. For cement type I, it lists maximum allowable chemical and physical property limits. It also specifies minimum strength requirements at various ages. For fly ash, it lists minimum chemical composition requirements and physical performance requirements when used as a cement replacement. The document provides reference standards for both cement and fly ash specifications.
This document contains specifications for cement type I and fly ash. For cement type I, it lists maximum allowable chemical and physical property limits. It also specifies minimum strength requirements at various ages. For fly ash, it lists minimum chemical composition requirements and physical performance requirements when used as a cement replacement. The document provides reference standards for both cement and fly ash specifications.
2 Sulfur trioxide (SO 3 ), max, % - When (C 3 A) is 8 % or less 3.0 - When (C 3 A) is more than 8 % 3.5 3 Loss on ignition, max, % 3.0 4 Alkali as Na2O, mx, % 0.6 5 Insoluble residue, max, % 3.0 6 Tricalcium aluminate (C 3 A), max, % - 7 C 4 AF + 2 C 3 A or C 4 AF + C 2 F, max, % - No Properties Cement Type I 1 Fineness, specic surface, m2/kg (alternative methods): - Turbidimeter test, min 160 - Air permeability test, min 280 2 Autoclave expansion, max, % 0.80 3 Strength, not less than the values shown for the ages indicated as follows: Compressive strength, kg/cm2 - 3 days 125 - 7 days 200 - 28 days 280 4 Time of setting (alternative methods): Gillmore test: - Initial set, min, not less than 60 - Final set, min, not more than 600 Vicat test: - Time of setting, min, not less than 45 - Time of setting, min, not more than 375 5 False set, min, % 50 Chemical Properties Physical Properties Cement Specification Cement Type V 6.0 2.3 - 3.0 0.6 3.0 5 20 Cement Type V 160 280 0.80 85 150 210 60 600 45 375 50 Chemical Properties Physical Properties Cement Specification No Properties Class F 1 Silicon dioxide (SiO2) plus aluminum oxide (Al2O3) plus iron oxide (Fe2O3), min, % 70 2 Sulfur trioxide (SO3), max, % 5 3 Moisture content, max, % 3 4 Loss on ignition, max, % 6 5 Total alkali calculated as Na3O, max, % 1.5 No Properties Class F 1 Fineness: - Amount retained when wet-sieved on 45 m (No. 325) sieve, max, % 34 2 Strength activity index: - With portland cement, at 7 days, min, percent of control 75 - With portland cement, at 28 days, min, percent of control 75 3 Water requirement, max, percent of control 105 4 Soundness: - Autoclave expansion or contraction, max, % 0.8 5 Uniformity requirements: The density and fineness of individual samples shall not vary from the average established by the ten preceding tests, or by all preceding tests if the number is less than ten, by more than: - Density, max variation from average, % 5 - Percent retained on 45-m (No. 325), max variation, 5 percentage points from average 6 Added shrinkage due to drying (at 28 days, max, %) 0.03 7 Reactivity with alkali cement: 0.02 Development of mortar at 14 days, max, % Reference SNI 03-2460-1991 ASTM C618 08a Fly Ash Specification Chemical Properties Physical Properties No Properties 1 Maximum concentration in combined mixing water A. Chloride as Cl-, gr/ltr B. Sulfate as SO4, gr/ltr C. Acids, Organic, etc, gr/ltr D. Total solids by mass, ppm No Properties 1 Compressive strength, min % control at 7 days A,B 2 Time of set, deviation from control, h: min A A Comparisons shall be based on xed proportions for a concrete mix design representative of questionable water supply and a control mix using 100 % potable water or distilled water. B Compressive strength results shall be based on at least two standard test specimens made from a composite sample. ASTM C1602/C1602M Water Specification Chemical Properties Physical Properties Limits 0.5 1.0 15.0 50,000 Limits 90 From 1:00 early to 1:30 later A Comparisons shall be based on xed proportions for a concrete mix design representative of B Compressive strength results shall be based on at least two standard test specimens made from Reference SNI 04-1989-F SNI 03-2847-2002 ASTM C1602/C1602M ACI 318-83 Water Specification Chemical Properties Physical Properties No Properties Split Sand Dust Size No. Nominal Size (Sieves with Square Openings) Mass Percent Size Percent Passing 1 Clay lumps and friable particles, max, % 3 3 3 2 63 to 37.5 mm - 9.5-mm (38-in.) 100 2 Material finer than 75-m (No. 200) sieve, max, % 1 5 5 3 50 to 25.0 mm 0 to 15 4.75-mm (No. 4) 95 to 100 3 Coal and lignite, max, % 0.5 0.5 0.5 357 50 to 4.75 mm 35 to 70 2.36-mm (No. 8) 80 to 100 4 Organic Impurities: - < No.3 - 4 37.5 to 19.0 mm 20 to 55 1.18-mm (No. 16) 50 to 85 5 Soundness: max, % 467 37.5 to 4.75 mm - 600-m (No. 30) 25 to 60 - Sodium Sulfate 12 12 12 5 25.0 to 12.5 mm 90 to 100 300-m (No. 50) 10 to 30 - Magnesium Sulfate 10 10 18 56 25.0 to 9.5 mm 90 to 100 150-m (No. 100) 2 to 10 6 Abrasion 50 - - 57 25.0 to 4.75 mm 95 to 100 7 Unit Weight, min, (ton/m 3 ) 1.2 1.2 1.2 6 19.0 to 9.5 mm 100 Reference 8 Specific Gravity, min 2.3 2.3 2.3 67 19.0 to 4.75 mm 100 SNI S-04-1989-F 9 Absorption, max, % 5 5 5 7 12.5 to 4.75 mm - SII 0052-80 10 Clay Content, max, % 5 1 5 8 9.5 to 2.36 mm - ASTM C33/C33M 89 9.5 to 1.18 mm - Note : 9 4.75 to 1.18 mm - Specification Gradation - Split 25.0 mm (1 in.) Gradation - Sand Aggregate Specification