Sunteți pe pagina 1din 28

Celsius 355 NH technical guide

Structural hollow sections

Contents
03 Introduction
04 Technical data
08 Size range charts
12 Sectional properties Celsius 355 Circular
16 Sectional properties Celsius 355 Elliptical
18 Sectional properties Celsius 355 Square
22 Sectional properties Celsius 355 Rectangular

02

Celsius 355 NH Technical Guide

CELSIUS 355 NH

Celsius 355 hot finished hollow section is


manufactured exclusively from normalised, fine
grain steel for outstanding performance.
Where failure is not an option, you can trust
Celsius 355 to deliver.

Celsius 355 key features:


Normalised fine grain steel, so free of
internal stresses and with a minimum
strength of 355 MPa allowing the highest
fabrication factors and enabling material
cost savings and lighter structures
Available in a wide range of circular, square,
rectangular and elliptical hollow sections
Tight corner radii, exceeding the standard
- enhancing the products aesthetic appeal
whilst avoiding the risk of brittle fracture
which occurs in some cold formed products
Dimensional consistency, high levels of
formability and, because the steel is fullykilled, excellent weldability
Certified as suitable for all structural
applications, fully compliant with design
codes and overcomes design risks associated
with other forms of hollow sectons
Certified as suitable for mechanical
applications, especially those involving
cyclical loading

Suitable for low temperature applications


(40J @ -20C)
Batch-tested to give the properties of
the specific delivered material; full test
certification supplied
Clearly marked as Celsius 355, with the
reassurance of batch traceability
Full technical support available
Excellent supply availability through
approved stockholders
All Celsius 355 material is CE marked and
is fully compliant with the Construction
Products Regulation
Suitable for galvanising

03

Celsius 355 NH Technical Guide Technical data

TECHNICAL DATA
High strength hot finished hollow sections suitable for all construction
and mechanical applications. Celsius 355 is suitable for all internal and
external applications to BS5950-1:2000, EN1993 and BS5400.

Celsius 355 hollow sections are supplied with a minimum yield


strength of 355 N/mm2 and comply fully with the European Standard for
hot finished structural hollow sections, EN10210: S355NH.

Mechanical properties
Yield strength

Tensile strength

ReH min N/mm2

Rm N/mm2 L0 = 5,65 S0

Elongation % min

Impact strength

Carbon

10mm x 10mm

equivalent

specimen

T 16mm

3mm < T 100mm

(CEV) max

355

470-630

22

-20

40

0.43

Chemical

composition % by mass
C

Si

Mn

Nb

Al total

max
max max max max ma

min

Ti Cr Ni Mo Cu

max max max max max max

0.20
0.50 0.90 0.035 0.030 0.050 0.12 0.020 0.03 0.30 0.50 0.10 0.35 0.020
1.65

Celsius 355 is produced from fully-killed steel critical to formability and weldability.

Inspection and testing


Celsius 355 hollow sections EN10210: S355NH are subject to specific
inspection and testing and are supplied with an inspection certificate
type 3.1 to EN10204.

Examples
Circular hollow section:
Celsius 355 114.3 x 6.3
or 114.3 x 6.3 CHS EN10210: Part 1: S355NH

Designation
Celsius 355 hollow sections are designated by their product name,
outside dimensions and thickness in millimetres.

Rectangular hollow section:


Celsius 355 100 x 50 x 5.0
or 100 x 50 x 5.0 RHS EN10210: Part 1: S355NH

CE marking
All Celsius 355 material is CE marked and is fully compliant with the
Construction Products Regulation.

Elliptical hollow section:


Celsius 355 elliptical 400 x 200 x 8.0
or 400 x 200 x 8.0 EHS EN10210: Part 1: S355NH
or simply
Celsius 355 EHS 400 x 200 x 8.0

04

Dimensional tolerances EN10210: Part 2


Circular/Ellipticals

Square/Rectangular

Outside dimension (D B and H)

Circular 1% with a min of 0.5mm and maximum of 10mm

1% with a min of 0.5mm

Ellipticals 1% with a min of 0.5mm (The permitted tolerance

is twice the value for H<250)

Thickness (T)

-10%

-10%

Note: Positive deviation limited by mass tolerance

Note: Positive deviation limited by mass tolerance

Squareness of side

90 degrees 1 degree

External corner profile

2T max at each corner*

(EN10210 has 3T max)

Concavity/convexity (x)

1% of the side, measured independently of

the tolerance on the outside dimension

Twist (V)

Ellipticals: 2mm plus 0.5mm/m max

2mm plus 0.5mm/m max

(The permitted tolerance is twice the value for H<250)

Section is placed on a flat surface with one end


held flat. At the other end the height difference of

the two lower corners is taken

Mass (M)

6% on individual lengths

6% on individual lengths

Straightness

Maximum 0.2% of the total length & 3mm over every

Maximum 0.2% of total length & 3mm over every

1m length

1m length

Ellipticals: The permitted tolerance is twice the value for H<250

Length +150mm/-0mm

+150mm/-0mm

Out-of-roundness (O)

Circular 2% for hollow sections having a diameter to thickness

ratio not exceeding 100

* Unless shown otherwise

05

Celsius 355 NH Technical Guide Technical data

Celsius 355 Square Hollow Sections length and tolerances


Size

Thickness

Special mill lengths

Tolerance

mm

mm m

Standard mill lengths

m**

mm

40 x 40 uti 100 x 100

All

6.0, 6.4, 7.5, 10.0 & 12.0

5.4 - 14.6

+ 150-0

120 x 120 uti 150 x 150 x 12.5

All

6.0, 6.4, 7.5, 10.0 & 12.0

6.0 - 14.5

+ 150-0

150 x 150 x 16.0

All

Check availability

6.0 - 13.5

+ 150-0

160 x 160 uti 400 x 400 x 16.0

All

10.0 & 12.0

6.0 - 15.3

+ 150-0

400 x 400 x 20.0

All

12.0 - 12.7 subject to availability

(uti up to and including)

Celsius 355 Rectangular Hollow Sections length and tolerances


Size

Thickness

Special mill lengths

Tolerance

mm

mm m

Standard mill lengths

m**

mm

50 x 30 uti 120 x 80

All

6.0, 6.4, 7.5, 10.0 & 12.0

5.4 - 14.6

+ 150-0

150 x 100 uti 200 x 100 x 12.5

All

6.0, 6.4, 7.5, 10.0 & 12.0

6.0 - 14.5

+ 150-0

200 x 100 x 16.0

All

Check availability

6.0 - 13.5

+ 150-0

200 x 120 uti 500 x 300 x 16.0

All

10.0 & 12.0

6.0 - 15.3

+ 150-0

500 x 300 x 20.0

All

12.0 - 12.7 subject to availability

(uti - up to and including)

Celsius 355 Circular Hollow Sections length and tolerances


Outside diameter

Thickness

Special mill lengths

Tolerance

mm

mm m

Standard mill lengths

m**

mm

21.3 - 33.7

All

6.0, 6.4 & 7.5

5.4 - 7.0

+ 150-0

*42.4

All

6.0, 6.4, 7.5, 10.0 & 12.0

5.4 - 12.0

+ 150-0

*48.3 - 114.3

All

6.0, 6.4, 7.5, 10.0 & 12.0

5.4 - 14.6

+ 150-0

139.7

All

6.0, 7.5, 10.0 & 12.0

6.0 - 14.5

+ 150-0

168.3

All

6.0, 7.5, 10.0 & 12.0

6.0 - 14.6

+ 150-0

193.7

All

6.0, 7.5, 10.0 & 12.0

6.0 - 14.6

+ 150-0

219.1 - 508.0

All

10.0 & 12.0

6.0 - 14.6

+ 150-0

Celsius 355 Elliptical Hollow Sections length and tolerances


Size

Thickness

Special mill lengths

Tolerance

mm

mm m

m**

mm

150 x 75

All

7.5, 10.0 & 12.0

6.0 - 14.5

+ 150-0

200 x 100

All

7.5, 10.0 & 12.0

6.0 - 14.5

+ 150-0

250 x 125

All

7.5, 10.0 & 12.0

6.0 - 14.5

+ 150-0

300 x 150

All

10.0 & 12.0

9.0 - 14.5

+ 150-0

400 x 200

All

10.0 & 12.0

9.0 - 14.5

+ 150-0

500 x 250

All

10.0 & 12.0

9.0 - 14.5

+ 150-0

** For thinner gauge material, check standard lengths


** Lengths available in 100mm increments

06

Standard mill lengths

07

Celsius 355 NH Technical Guide Size range charts

SIZERANGECHARTS
Celsius 355 Circular Hollow Sections
Outside Diameter (mm)

Thickness (mm)
2.6 2.9 3.2 3.6 4.0 4.5 5.0 5.6 6.3 8.0 10.0 12.5 14.2 16.0

21.3
26.9
33.7
42.4
48.3
60.3
76.1
88.9
101.6
114.3
139.7
168.3
193.7
219.1
244.5
273.0
323.9
355.6
406.4
457.0
508.0

The above table shows our normal capability, reference should be made to the sectional properties table to identify sizes that are readily available
and should be given preference.

Minimum order quantities may apply to some sizes.


Other sizes can be manufactured please contact your account manager.

08

Celsius 355 Elliptical Hollow Sections


Size (mm)

Thickness (mm)
4.0

5.0

6.3

8.0

10.0 12.5

14.2 16.0

150 x 75
200 x 100
250 x 125
300 x 150
400 x 200
500 x 250

Celsius 355 Square Hollow Sections


Size (mm)

Thickness (mm)
3.0 3.2 3.6 4.0 5.0 6.3

7.1 8.0 8.8 10.0 12.5 14.2 16.0 20.0

40 x 40
50 x 50
60 x 60
70 x 70
80 x 80
90 x 90
100 x 100
120 x 120
140 x 140
150 x 150
160 x 160
180 x 180
200 x 200
250 x 250
260 x 260
300 x 300
350 x 350
400 x 400

For sizes shown

please contact your account manager.

09

Celsius 355 NH Technical Guide Size range charts

Celsius 355 Rectangular Hollow Sections


Size (mm)

Thickness (mm)
3.0 3.2 3.6 4.0 5.0 6.3 7.1 8.0 8.8 10.0 12.5 14.2 16.0 20.0

50 x 30
60 x 40
80 x 40
90 x 50
100 x 50
100 x 60
120 x 60
120 x 80
150 x 100
160 x 80
180 x 60
180 x 100
200 x 100
200 x 120
200 x 150
220 x 120
250 x 100
250 x 150
250 x 200
260 x 140
260 x 180
300 x 100
300 x 150
300 x 200
300 x 250
340 x 100
350 x 150
350 x 250
400 x 120
400 x 150
400 x 200
400 x 300
450 x 250
500 x 200
500 x 300

The above table shows our normal capability, reference should be made to the sectional properties table to identify sizes that are readily available and
should be given preference.

Minimum order quantities may apply to some sizes.


Other sizes can be manufactured please contact your account manager.
For sizes shown
please contact your account manager.

10

11

Celsius 355 NH Technical Guide Sectional properties Celsius 355 circular


Z

CELSIUS 355 CIRCULAR

Y
T

Celsius 355 EN10210: S355NH Hot finished circular hollow section


Outside

Thickness

Mass

Diameter
D

mm mm

M
kg/m

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

21.3

2.6 1.20 1.53 0.681 0.668 0.639 0.915 1.36 1.28 0.067 834

2.9 1.32 1.68 0.727 0.659 0.683 0.990 1.45 1.37 0.067 760

3.2 1.43 1.82 0.768 0.650 0.722 1.06 1.54 1.44 0.067 700

26.9

2.6 1.56
1.98 1.48 0.864 1.10 1.54 2.96
2.20 0.085 642

2.9 1.72
2.19 1.60 0.855 1.19 1.68 3.19
2.38 0.085 583

3.2 1.87
2.38 1.70 0.846 1.27 1.81 3.41
2.53 0.085 535

3.6 2.07
2.64 1.83 0.834 1.36 1.97 3.66
2.72 0.085 483

33.7

2.6
1.99
2.54 3.09 1.10 1.84 2.52 6.19
3.67 0.106 501

2.9
2.20
2.81 3.36 1.09 1.99 2.76 6.71
3.98 0.106 454

3.2
2.41
3.07 3.60 1.08 2.14 2.99 7.21
4.28 0.106 415

3.6
2.67
3.40 3.91 1.07 2.32 3.28 7.82
4.64 0.106 374

4.0
2.93
3.73 4.19 1.06 2.49 3.55 8.38
4.97 0.106 341

4.5
3.24
4.13 4.50 1.04 2.67 3.87 9.01
5.35 0.106 309

5.0
3.54
4.51 4.78 1.03 2.84 4.16 9.57
5.68 0.106 283

42.4

2.6
2.55
3.25 6.46 1.41 3.05 4.12 12.9
6.10 0.133 392

2.9
2.82
3.60 7.06 1.40 3.33 4.53 14.1
6.66 0.133 354

3.2
3.09
3.94 7.62 1.39 3.59 4.93 15.2
7.19 0.133 323

3.6
3.44
4.39 8.33 1.38 3.93 5.44 16.7
7.86 0.133 290

4.0
3.79
4.83 8.99 1.36 4.24 5.92 18.0
8.48 0.133 264

4.5
4.21
5.36 9.76 1.35 4.60 6.49 19.5
9.20 0.133 238

5.0
4.61
5.87 10.5 1.33 4.93 7.04 20.9
9.86 0.133 217

12

Celsius 355 EN10210: S355NH Hot finished circular hollow section (continued)
Outside

Thickness

Mass

Diameter
D

mm mm

M
kg/m

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

48.3

2.6
2.93
3.73 9.78 1.62 4.05 5.44 19.6
8.10 0.152 341

2.9
3.25
4.14 10.7 1.61 4.43 5.99 21.4
8.86 0.152 308

3.2
3.56
4.53 11.6 1.60 4.80 6.52 23.2
9.59 0.152 281

3.6
3.97
5.06 12.7 1.59 5.26 7.21 25.4
10.5 0.152 252

4.0
4.37
5.57 13.8 1.57 5.70 7.87 27.5
11.4 0.152 229

4.5
4.86
6.19 15.0 1.56 6.21 8.66 30.0
12.4 0.152 206

5.0
5.34
6.80 16.2 1.54 6.69 9.42 32.3
13.4 0.152 187

5.6
5.90
7.51 17.4 1.52 7.21 10.3 34.8
14.4 0.152 170

6.3
6.53
8.31 18.7 1.50 7.76 11.2 37.5
15.5 0.152 153

60.3

2.6
3.70
4.71 19.7 2.04 6.52 8.66 39.3
13.0 0.189 270

2.9
4.11
5.23 21.6 2.03 7.16 9.56 43.2
14.3 0.189 244

3.2
4.51
5.74 23.5 2.02 7.78 10.4 46.9
15.6 0.189 222

3.6
5.03
6.41 25.9 2.01 8.58 11.6 51.7
17.2 0.189 199

4.0
5.55
7.07 28.2 2.00 9.34 12.7 56.3
18.7 0.189 180

4.5
6.19
7.89 30.9 1.98 10.2 14.0 61.8
20.5 0.189 161

5.0
6.82
8.69 33.5 1.96 11.1 15.3 67.0
22.2 0.189 147

5.6
7.55
9.62 36.4 1.94 12.1 16.8 72.7
24.1 0.189 132

6.3
8.39
10.7 39.5 1.92 13.1 18.5 79.0
26.2 0.189 119

8.0
10.3
13.1 46.0 1.87 15.3 22.1 92.0
30.5 0.189 96.9

76.1

2.9
5.24
6.67 44.7 2.59 11.8 15.5 89.5
23.5 0.239 191

3.2
5.75
7.33 48.8 2.58 12.8 17.0 97.6
25.6 0.239 174

3.6
6.44
8.20 54.0 2.57 14.2 18.9 108
28.4 0.239 155

4.0
7.11
9.06 59.1 2.55 15.5 20.8 118
31.0 0.239 141

4.5
7.95
10.1 65.1 2.54 17.1 23.1 130
34.2 0.239 126

5.0
8.77
11.2 70.9 2.52 18.6 25.3 142
37.3 0.239 114

5.6
9.74
12.4 77.5 2.50 20.4 27.9 155
40.8 0.239 103

6.3
10.8
13.8 84.8 2.48 22.3 30.8 170
44.6 0.239 92.2

8.0 13.4
17.1 101 2.42 26.4 37.3 201 52.9 0.239 74.4

88.9

2.9
6.15
7.84 72.5 3.04 16.3 21.5 145
32.6 0.279 163

3.2
6.76
8.62 79.2 3.03 17.8 23.5 158
35.6 0.279 148

3.6
7.57
9.65 87.9 3.02 19.8 26.2 176
39.5 0.279 132

4.0
8.38
10.7 96.3 3.00 21.7 28.9 193
43.3 0.279 119

4.5
9.37
11.9 107 2.99 24.0 32.1 213
47.9 0.279 107

5.0 10.3
13.2 116 2.97 26.2 35.2 233 52.4 0.279 96.7

5.6 11.5
14.7 128 2.95 28.7 38.9 255 57.5 0.279 86.9

6.3 12.8
16.3 140 2.93 31.5 43.1 280 63.1 0.279 77.9

8.0 16.0
20.3 168 2.87 37.8 52.5 336 75.6 0.279 62.7

10.0 19.5 24.8 196 2.81 44.1 62.6 392 88.2 0.279 51.4

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply

13

Celsius 355 NH Technical Guide Sectional properties Celsius 355 circular

Y
T

Celsius 355 EN10210: S355NH Hot finished circular hollow section (continued)
Outside

Thickness

Mass

Diameter
D

mm mm

M
kg/m

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

101.6 3.2
7.77
9.89 120 3.48 23.6 31.0 240
47.2 0.319 129

3.6
8.70
11.1 133 3.47 26.2 34.6 266
52.5 0.319 115

4.0
9.63
12.3 146 3.45 28.8 38.1 293
57.6 0.319 104

4.5 10.8
13.7 162 3.44 31.9 42.5 324 63.8 0.319 92.8

5.0 11.9
15.2 177 3.42 34.9 46.7 355 69.9 0.319 84.0

5.6 13.3
16.9 195 3.40 38.4 51.7 390 76.9 0.319 75.4

6.3 14.8
18.9 215 3.38 42.3 57.3 430 84.7 0.319 67.5

8.0
18.5
23.5 260 3.32 51.1 70.3 519
102 0.319 54.2

10.0 22.6 28.8 305 3.26 60.1 84.2 611 120 0.319 44.3

114.3 3.2
8.77
11.2 172 3.93 30.2 39.5 345
60.4 0.359 114

3.6
9.83
12.5 192 3.92 33.6 44.1 384
67.2 0.359 102

4.0 10.9
13.9 211 3.90 36.9 48.7 422 73.9 0.359 91.9

4.5 12.2
15.5 234 3.89 41.0 54.3 469 82.0 0.359 82.1

5.0 13.5
17.2 257 3.87 45.0 59.8 514 89.9 0.359 74.2

5.6 15.0
19.1 283 3.85 49.6 66.2 566 99.1 0.359 66.6

6.3
16.8
21.4 313 3.82 54.7 73.6 625
109 0.359 59.6

8.0
21.0
26.7 379 3.77 66.4 90.6 759
133 0.359 47.7

10.0 25.7 32.8 450 3.70 78.7 109 899 157 0.359 38.9

139.7

3.2 10.8
13.7 320 4.83 45.8 59.6 640 91.6 0.439 92.8

3.6
12.1
15.4 357 4.81 51.1 66.7 713
102 0.439 82.8

4.0
13.4
17.1 393 4.80 56.2 73.7 786
112 0.439 74.7

4.5
15.0
19.1 437 4.78 62.6 82.3 874
125 0.439 66.6

5.0
16.6
21.2 481 4.77 68.8 90.8 961
138 0.439 60.2

5.6
18.5
23.6 531 4.75 76.1 101
1062
152 0.439 54.0

6.3
20.7
26.4 589 4.72 84.3 112
1177
169 0.439 48.2

8.0
26.0
33.1 720 4.66 103 139
1441
206 0.439 38.5

10.0
32.0
40.7 862 4.60 123 169
1724
247 0.439 31.3

12.5 39.2 50.0 1020 4.52 146 203 2040 292 0.439 25.5

168.3 5.0
20.1
25.7 856 5.78 102 133
1712
203 0.529 49.7

5.6
22.5
28.6 948 5.76 113 148
1897
225 0.529 44.5

6.3 25.2
32.1 1053 5.73 125 165 2107
250 0.529 39.7

8.0 31.6
40.3 1297 5.67 154 206 2595
308 0.529 31.6

10.0 39.0 49.7 1564 5.61 186 251 3128 372 0.529 25.6

12.5 48.0 61.2 1868 5.53 222 304 3737 444 0.529 20.8

193.7 5.0 23.3


29.6 1320 6.67 136 178 2640
273 0.609 43.0

5.6 26.0
33.1 1465 6.65 151 198 2930
303 0.609 38.5

6.3 29.1
37.1 1630 6.63 168 221 3260
337 0.609 34.3

8.0 36.6
46.7 2016 6.57 208 276 4031
416 0.609 27.3

10.0 45.3 57.7 2442 6.50 252 338 4883 504 0.609 22.1

12.5 55.9 71.2 2934 6.42 303 411 5869 606 0.609 17.9

16.0 70.1 89.3 3554 6.31 367 507 7109 734 0.609 14.3

219.1 4.5 23.8


30.3 1747 7.59 159 207 3494
319 0.688 42.0

5.0 26.4
33.6 1928 7.57 176 229 3856
352 0.688 37.9

5.6 29.5
37.6 2142 7.55 195 255 4283
391 0.688 33.9

6.3 33.1
42.1 2386 7.53 218 285 4772
436 0.688 30.2

8.0 41.6
53.1 2960 7.47 270 357 5919
540 0.688 24.0

10.0 51.6 65.7 3598 7.40 328 438 7197 657 0.688 19.4

12.5 63.7 81.1 4345 7.32 397 534 8689 793 0.688 15.7

14.2 71.8 91.4 4820 7.26 440 597 9640 880 0.688 13.9

16.0
80.1
102 5297 7.20 483 661
10593
967 0.688 12.5

14

Celsius 355 EN10210: S355NH Hot finished circular hollow section (continued)
Outside

Thickness

Mass

Diameter
D

mm mm

M
kg/m

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

244.5 5.0 29.5


37.6 2699 8.47 221 287 5397
441 0.768 33.9

5.6 33.0
42.0 3000 8.45 245 320 6000
491 0.768 30.3

6.3 37.0
47.1 3346 8.42 274 358 6692
547 0.768 27.0

8.0 46.7
59.4 4160 8.37 340 448 8321
681 0.768 21.4

10.0 57.8 73.7 5073 8.30 415 550 10146 830 0.768 17.3

12.5 71.5 91.1 6147 8.21 503 673 12295


1006 0.768 14.0

14.2 80.6 103

6837

8.16

559

754 13674 1119 0.768

12.4

16.0 90.2 115

7533

8.10

616

837 15066 1232 0.768

11.1

273.0 5.0 33.0


42.1 3781 9.48 277 359 7562
554 0.858 30.3

5.6 36.9
47.0 4207 9.46 308 400 8413
616 0.858 27.1

6.3 41.4
52.8 4696 9.43 344 448 9392
688 0.858 24.1

8.0 52.3
66.6 5852 9.37 429 562
11703
857 0.858 19.1

10.0 64.9 82.6 7154 9.31 524 692 14308


1048 0.858 15.4

12.5 80.3 102

8697

9.22

637

849 17395 1274 0.858

12.5

14.2 90.6 115

9695

9.16

710

952 19390 1421 0.858

11.0

16.0 101 129 10707 9.10 784 1058


21414
1569 0.858 9.86

323.9 5.0
39.3
50.1 6369 11.3 393 509
12739
787 1.02 25.4

5.6
44.0
56.0 7094 11.3 438 567
14188
876 1.02 22.7

6.3
49.3
62.9 7929 11.2 490 636
15858
979 1.02 20.3

8.0 62.3
79.4 9910 11.2 612 799
19820
1224 1.02 16.0

10.0 77.4 98.6 12158 11.1 751 986 24317


1501 1.02 12.9

12.5 96.0 122

14.2
108 138 16599 11.0 1025
1363
33198
2050 1.02 9.22

16.0
121 155 18390 10.9 1136
1518
36780
2271 1.02 8.23

355.6

6.3 54.3 69.1 10547 12.4 593 769 21094


1186 1.12 18.4

14847 11.0

917 1213 29693 1833

1.02

10.4

8.0 68.6 87.4 13201 12.3 742 967 26403


1485 1.12 14.6

10.0 85.2 109

12.5
106 135 19852 12.1 1117
1472
39704
2233 1.12 9.45

14.2
120 152 22227 12.1 1250
1656
44455
2500 1.12 8.36

16.0
134 171 24663 12.0 1387
1847
49326
2774 1.12 7.46

406.4

6.3 62.2 79.2 15849 14.1 780 1009


31699
1560 1.28 16.1

16223 12.2

19874 14.1

912 1195 32447 1825

978 1270 39748 1956

1.12

1.28

11.7

8.0 78.6 100

10.0
97.8
125 24476 14.0 1205
1572
48952
2409 1.28 10.2

12.7

12.5
121 155 30031 13.9 1478
1940
60061
2956 1.28 8.24

14.2
137 175 33685 13.9 1658
2185
67371
3315 1.28 7.28

16.0
154 196 37449 13.8 1843
2440
74898
3686 1.28 6.49

457.0

6.3 70.0 89.2 22654 15.9 991 1280


45308
1983 1.44 14.3

8.0 88.6
113 28446 15.9 1245
1613
56893
2490 1.44 11.3

10.0
110 140 35091 15.8 1536
1998
70183
3071 1.44 9.07

12.5
137 175 43145 15.7 1888
2470
86290
3776 1.44 7.30

14.2
155 198 48464 15.7 2121
2785
96928
4242 1.44 6.45

16.0
174 222 53959 15.6 2361
3113
107919
4723 1.44 5.75

508.0

6.3 77.9 99.3 31246 17.7 1230 1586


62493
2460 1.60 12.8

8.0 98.6
126 39280 17.7 1546
2000
78560
3093 1.60 10.1

10.0
123 156 48520 17.6 1910
2480
97040
3820 1.60 8.14

12.5
153 195 59755 17.5 2353
3070
119511
4705 1.60 6.55

14.2
173 220 67199 17.5 2646
3463
134397
5291 1.60 5.78

16.0
194 247 74909 17.4 2949
3874
149818
5898 1.60 5.15

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply
15

Celsius 355 NH Technical Guide Sectional properties Celsius 355 elliptical

B
T

CELSIUS 355 ELLIPTICAL

Celsius 355 EN10210: S355NH Hot finished elliptical hollow section


Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

150 x 75

4.0 10.7 13.6 301 101 4.70 2.72 40.1 26.9 56.1 34.4 303 60.1 0.363 93.4

5.0 13.3 16.9 367 122 4.66 2.69 48.9 32.5 68.9 42.0 367 72.2 0.363 75.4

6.3 16.5 21.0 448 147 4.62 2.64 59.7 39.1 84.9 51.5 443 86.3 0.363 60.6

200 x 100 5.0 17.9 22.8 897 302 6.27 3.64 89.7 60.4 125 76.8 905 135 0.484 55.9

6.3 22.3 28.4 1103 368 6.23 3.60 110 73.5 155 94.7
1105 163 0.484 44.8

8.0 28.0 35.7 1358 446 6.17 3.54 136 89.3 193 117
1347 197 0.484 35.7

10.0 34.5 44.0 1637 529 6.10 3.47 164 106 235 141 1605 232 0.484 29.0

12.5 42.4 54.0 1954 619 6.02 3.39 195 124 284 169 1889 269 0.484 23.6

250 x 125

6.3

8.0 35.4 45.1 2732 909 7.78 4.49 219 145 307 188 2734 323 0.605 28.2

28.2

35.9

2205

742

7.84

4.55

176

119

246

151

2224

265

0.605

35.5

10.0 43.8 55.8 3316 1090 7.71 4.42 265 174 376 228 3288 385 0.605 22.8

12.5 53.9 68.7 3996 1292 7.63 4.34 320 207 458 276 3918 453 0.605 18.5

300 x 150

8.0

10.0 53.0 67.5 5872 1950 9.32 5.37 391 260 551 336 5867 577 0.726 18.9

42.8

54.5

4813

1616

9.39

5.44

321

215

449

275

4846

481

0.726

23.4

12.5 65.5 83.4 7120 2334 9.24 5.29 475 311 674 409 7047 686 0.726 15.3

14.2 73.8 94.0 7921 2573 9.18 5.23 528 343 755 456 7790 753 0.726 13.5

16.0 82.5 105 8731 2809 9.12 5.17 582 374 837 503 8529 818 0.726 12.1

400 x 200

8.0

10.0 71.5 91.1 14348 4829 12.5 7.28 717 483 1001 615
14473
1079 0.969 14.0

57.6

73.4

11689

3966

12.6

7.35

584

397

811

500

11858

890

0.969

17.4

12.5 88.6 113 17531 5843 12.5 7.19 877 584 1232 753
17558
1299 0.969 11.3

14.2 100 127 19609 6491 12.4 7.14 980 649 1384
843
19544
1438
0.969 9.99

16.0 112 143 21734 7143 12.3 7.07 1087 714 1541 936
21551 1577 0.969 8.92

500 x 250 10.0 90.0 115 28539 9682 15.8 9.19 1142 775 1585 976
28950 1739 1.21 11.1

12.5 112 142 35030 11791 15.7 9.10 1401 943 1956
1201
35333 2108 1.21 8.95

14.2 126 161 39305 13158 15.6 9.04 1572 1053 2202 1349
39491 2346 1.21

7.91

16.0 142 180 43709 14549 15.6 8.98 1748 1164 2459 1501
43737 2586 1.21

7.06

All above sizes are non-standard and therefore minimum order quantities may apply.

16

17

Celsius 355 NH Technical Guide Sectional properties Celsius 355 square


B

CELSIUS 355 SQUARE

Y
T
Z

Celsius 355 EN10210: S355NH Hot finished square hollow section


Size

Thickness

Mass


B x B

mm mm

M
kg/m

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

40 x 40 3.0
3.41
4.34 9.78 1.50 4.89 5.97 15.7
7.10 0.152 293

3.2
3.61
4.60 10.2 1.49 5.11 6.28 16.5
7.42 0.152 277

3.6
4.01
5.10 11.1 1.47 5.54 6.88 18.1
8.01 0.151 250

4.0
4.39
5.59 11.8 1.45 5.91 7.44 19.5
8.54 0.150 228

5.0
5.28
6.73 13.4 1.41 6.68 8.66 22.5
9.60 0.147 189

50 x 50 3.0
4.35
5.54 20.2 1.91 8.08 9.70 32.1
11.8 0.192 230

3.2
4.62
5.88 21.2 1.90 8.49 10.2 33.8
12.4 0.192 217

3.6
5.14
6.54 23.2 1.88 9.27 11.3 37.2
13.5 0.191 195

4.0
5.64
7.19 25.0 1.86 9.99 12.3 40.4
14.5 0.190 177

5.0
6.85
8.73 28.9 1.82 11.6 14.5 47.6
16.7 0.187 146

6.3
8.31
10.6 32.8 1.76 13.1 17.0 55.2
18.8 0.184 120

7.1
9.14
11.6 34.5 1.72 13.8 18.3 58.9
19.8 0.182 109

8.0
10.0
12.8 36.0 1.68 14.4 19.5 62.3
20.6 0.179 99.9

60 x 60 3.0
5.29
6.74 36.2 2.32 12.1 14.3 56.9
17.7 0.232 189

3.2
5.62
7.16 38.2 2.31 12.7 15.2 60.2
18.6 0.232 178

3.6
6.27
7.98 41.9 2.29 14.0 16.8 66.5
20.4 0.231 160

4.0
6.90
8.79 45.4 2.27 15.1 18.3 72.5
22.0 0.230 145

5.0
8.42
10.7 53.3 2.23 17.8 21.9 86.4
25.7 0.227 119

6.3
10.3
13.1 61.6 2.17 20.5 26.0 102
29.6 0.224 97.2

7.1
11.4
14.5 65.8 2.13 21.9 28.2 110
31.6 0.222 88.0

8.0
12.5
16.0 69.7 2.09 23.2 30.4 118
33.4 0.219 79.9

70 x 70 3.0
6.24
7.94 59.0 2.73 16.9 19.9 92.2
24.8 0.272 160

3.2
6.63
8.44 62.3 2.72 17.8 21.0 97.6
26.1 0.272 151

3.6
7.40
9.42 68.6 2.70 19.6 23.3 108
28.7 0.271 135

4.0
8.15
10.4 74.7 2.68 21.3 25.5 118
31.2 0.270 123

5.0
9.99
12.7 88.5 2.64 25.3 30.8 142
36.8 0.267 100

6.3 12.3
15.6 104 2.58 29.7 36.9 169 42.9 0.264 81.5

7.1 13.6
17.3 112 2.54 32.0 40.3 185 46.1 0.262 73.5

8.0 15.0
19.2 120 2.50 34.2 43.8 200 49.2 0.259 66.5

8.8 16.3
20.7 126 2.46 35.9 46.6 212 51.6 0.257 61.5

80 x 80 3.0
7.18
9.14 89.8 3.13 22.5 26.3 140
33.0 0.312 139

3.2
7.63
9.72 95.0 3.13 23.7 27.9 148
34.9 0.312 131

3.6
8.53
10.9 105 3.11 26.2 31.0 164
38.5 0.311 117

4.0
9.41
12.0 114 3.09 28.6 34.0 180
41.9 0.310 106

5.0 11.6
14.7 137 3.05 34.2 41.1 217 49.8 0.307 86.5

6.3 14.2
18.1 162 2.99 40.5 49.7 262 58.7 0.304 70.2

7.1 15.8
20.2 176 2.95 43.9 54.5 286 63.5 0.302 63.2

8.0 17.5
22.4 189 2.91 47.3 59.5 312 68.3 0.299 57.0

8.8 19.0
24.2 200 2.87 50.0 63.7 332 72.0 0.297 52.6

90 x 90

3.6

4.0 10.7
13.6 166 3.50 37.0 43.6 260 54.2 0.350 93.7

9.66

12.3

152

3.52

33.8

39.7

237

49.7

0.351

104

5.0 13.1
16.7 200 3.45 44.4 53.0 316 64.8 0.347 76.1

6.3 16.2
20.7 238 3.40 53.0 64.3 382 77.0 0.344 61.6

7.1 18.1
23.0 260 3.36 57.7 70.8 419 83.7 0.342 55.4

8.0 20.1
25.6 281 3.32 62.6 77.6 459 90.5 0.339 49.9

8.8 21.8
27.8 299 3.28 66.5 83.4 492 96.0 0.337 45.9

18

Y
T
Z

Celsius 355 EN10210: S355NH Hot finished square hollow section (continued)
Size

Thickness

Mass


B x B

mm mm

M
kg/m
10.8

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

100 x 100

3.6

4.0 11.9
15.2 232 3.91 46.4 54.4 361 68.2 0.390 83.9

13.7

212

3.92

42.3

49.5

328

62.3

0.391

92.7

5.0 14.7
18.7 279 3.86 55.9 66.4 439 81.8 0.387 68.0

6.3 18.2
23.2 336 3.80 67.1 80.9 534 97.8 0.384 54.9

7.1
20.3
25.8 367 3.77 73.4 89.2 589
107 0.382 49.3

8.0
22.6
28.8 400 3.73 79.9 98.2 646
116 0.379 44.3

8.8
24.5
31.3 426 3.69 85.2 106 694
123 0.377 40.7

10.0 27.4 34.9 462 3.64 92.4 116 761 133 0.374 36.5

120 x 120

4.0

5.0
17.8
22.7 498 4.68 83.0 97.6 777
122 0.467 56.0

14.4

18.4

410

4.72

68.4

79.7

635

101

0.470

69.3

6.3
22.2
28.2 603 4.62 100 120 950
147 0.464 45.1

7.1
24.7
31.5 663 4.59 110 133
1051
161 0.462 40.4

8.0
27.6
35.2 726 4.55 121 146
1160
176 0.459 36.2

8.8
30.1
38.3 779 4.51 130 158
1252
189 0.457 33.3

10.0
33.7
42.9 852 4.46 142 175
1382
206 0.454 29.7

12.5
40.9
52.1 982 4.34 164 207
1623
236 0.448 24.5

140 x 140
5.0
21.0
26.7 807 5.50 115 135
1253
170 0.547 47.7

6.3
26.1
33.3 984 5.44 141 166
1540
206 0.544 38.3

7.1 29.2
37.2 1086 5.40 155 184 1709
227 0.542 34.2

8.0 32.6
41.6 1195 5.36 171 204 1892
249 0.539 30.7

8.8 35.6
45.4 1287 5.33 184 221 2048
268 0.537 28.1

10.0 40.0 50.9 1416 5.27 202 246 2272 294 0.534 25.0

12.5 48.7 62.1 1653 5.16 236 293 2696 342 0.528 20.5

150 x 150

5.0

6.3 28.1
35.8 1223 5.85 163 192 1909
240 0.584 35.6

7.1 31.4
40.0 1352 5.81 180 213 2121
264 0.582 31.8

8.0 35.1
44.8 1491 5.77 199 237 2351
291 0.579 28.5

22.6

28.7

1002

5.90

134

156

1550

197

0.587

44.3

8.8 38.4
48.9 1608 5.74 214 257 2549
313 0.577 26.1

10.0 43.1 54.9 1773 5.68 236 286 2832 344 0.574 23.2

12.5 52.7 67.1 2080 5.57 277 342 3375 402 0.568 19.0

14.2 58.9 75.0 2262 5.49 302 377 3707 436 0.563 17.0

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply
19

Celsius 355 NH Technical Guide Sectional properties Celsius 355 square

Y
T
Z

Celsius 355 EN10210: S355NH Hot finished square hollow section (continued)
Size

Thickness

Mass


B x B

mm mm

M
kg/m
24.1

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

160 x 160

5.0

6.3 30.1
38.3 1499 6.26 187 220 2333
275 0.624 33.3

30.7

1225

6.31

153

178

1892

226

0.627

41.5

7.1 33.7
42.9 1659 6.22 207 245 2595
304 0.622 29.7

8.0 37.6
48.0 1831 6.18 229 272 2880
335 0.619 26.6

8.8 41.1
52.4 1978 6.14 247 295 3125
361 0.617 24.3

10.0 46.3 58.9 2186 6.09 273 329 3478 398 0.614 21.6

12.5 56.6 72.1 2576 5.98 322 395 4158 467 0.608 17.7

14.2 63.3 80.7 2809 5.90 351 436 4579 508 0.603 15.8

16.0 70.2 89.4 3028 5.82 379 476 4988 546 0.599 14.2

180 x 180

5.0

6.3 34.0
43.3 2168 7.07 241 281 3361
355 0.704 29.4

7.1 38.1
48.6 2404 7.04 267 314 3744
393 0.702 26.2

8.0 42.7
54.4 2661 7.00 296 349 4162
434 0.699 23.4

27.3

34.7

1765

7.13

196

227

2718

290

0.707

36.7

8.8 46.7
59.4 2880 6.96 320 379 4524
469 0.697 21.4

10.0 52.5 66.9 3193 6.91 355 424 5048 518 0.694 19.0

12.5 64.4 82.1 3790 6.80 421 511 6070 613 0.688 15.5

14.2 72.2 92.0 4154 6.72 462 566 6711 670 0.683 13.8

16.0
80.2
102 4504 6.64 500 621 7343
724 0.679 12.5

200 x 200

5.0

6.3 38.0
48.4 3011 7.89 301 350 4653
444 0.784 26.3

7.1 42.6
54.2 3345 7.85 335 391 5189
493 0.782 23.5

8.0 47.7
60.8 3709 7.81 371 436 5778
545 0.779 21.0

30.4

38.7

2445

7.95

245

283

3756

362

0.787

32.9

8.8 52.2
66.5 4021 7.78 402 474 6288
590 0.777 19.2

10.0 58.8 74.9 4471 7.72 447 531 7031 655 0.774 17.0

12.5 72.3 92.1 5336 7.61 534 643 8491 778 0.768 13.8

14.2
81.1
103 5872 7.54 587 714 9417
854 0.763 12.3

16.0
90.3
115 6394 7.46 639 785
10340
927 0.759 11.1

250 x 250

5.0

6.3 47.9
61.0 6014 9.93 481 556 9238
712 0.984 20.9

7.1 53.7
68.4 6701 9.90 536 622
10325
792 0.982 18.6

8.0 60.3
76.8 7455 9.86 596 694
11525
880 0.979 16.6

38.3

48.7

4861

9.99

389

447

7430

577

0.987

26.1

8.8 66.0
84.1 8107 9.82 649 758
12572
955 0.977 15.2

10.0 74.5 94.9 9055 9.77 724 851 14106


1065 0.974 13.4

12.5 91.9 117 10915 9.66 873 1037


17164
1279 0.968 10.9

14.2 103 132 12094 9.58 967 1158


19139
1413 0.963 9.67

16.0 115 147 13267 9.50 1061 1280


21138
1546 0.959 8.67

20

Y
T
Z

Celsius 355 EN10210: S355NH Hot finished square hollow section (continued)
Size

Thickness

Mass


B x B

mm mm

M
kg/m
57.8

Sectional

Moment

Radius

Elastic

Plastic

Torsional

Superficial

Approx.

area

of inertia

of gyration

modulus

modulus

constants

area/m

length

Wel Wpl It Ct As /tonne

cm2 cm4 cm cm3 cm3 cm4 cm3 m2/m m/t

300 x 300

6.3

7.1 64.9 82.6 11775 11.9 785 906 18061


1163 1.18 15.4

73.6

10547

12.0

8.0 72.8 92.8 13128 11.9 875 1013


20194
1294 1.18 13.7

809

16136

1043

8.8 79.8 102

10.0
90.2
115 16026 11.8 1068
1246
24807
1575 1.17 11.1

12.5
112 142 19442 11.7 1296
1525
30333
1904 1.17 8.97

14.2
126 160 21637 11.6 1442
1708
33938
2114 1.16 7.95

16.0
141 179 23850 11.5 1590
1895
37622
2325 1.16 7.12

350 x 350

8.0

8.8 93.6
119 23055 13.9 1317
1522
35413
1950 1.38 10.7

10.0
106 135 25884 13.9 1479
1715
39886
2185 1.37 9.44

12.5
131 167 31541 13.7 1802
2107
48934
2654 1.37 7.62

14.2
148 189 35211 13.7 2012
2364
54879
2957 1.36 6.76

16.0
166 211 38942 13.6 2225
2630
60990
3264 1.36 6.04

400 x 400

8.0

8.8 107 137 34798 15.9 1740


2004
53290
2579 1.58 9.31

10.0
122 155 39128 15.9 1956
2260
60092
2895 1.57 8.22

12.5
151 192 47839 15.8 2392
2782
73906
3530 1.57 6.63

14.2
170 217 53526 15.7 2676
3127
83026
3942 1.56 5.87

16.0
191 243 59344 15.6 2967
3484
92442
4362 1.56 5.24

97.9

125

21129

31857

13.9

16.0

1207

1593

1392

1830

32384

48695

1789

2363

1.18

17.3

109

954 1107 22060 1409

1.18

85.4

14305 11.9

703

1.38

1.58

12.5

11.7

10.2

20.0 #
235 300 71535 15.4 3577
4247
112489
5237 1.55 4.25

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply

SAW Process (single longitudinal seam weld, slightly proud)

21

Celsius 355 NH Technical Guide Sectional properties Celsius 355 rectangular

CELSIUS 355 RECTANGULAR

H
T

Celsius 355 EN10210: S355NH Hot finished rectangular hollow section


Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

50 x 30

3.0 3.41 4.34 13.6 5.94 1.77 1.17 5.43 3.96 6.88 4.76 13.5 6.51 0.152 293

3.2 3.61 4.60 14.2 6.20 1.76 1.16 5.68 4.13 7.25 5.00 14.2 6.80 0.152 277

3.6 4.01 5.10 15.4 6.67 1.74 1.14 6.16 4.45 7.94 5.46 15.4 7.31 0.151 250

4.0 4.39 5.59 16.5 7.08 1.72 1.13 6.60 4.72 8.59 5.88 16.6 7.77 0.150 228

5.0 5.28 6.73 18.7 7.89 1.67 1.08 7.49 5.26 10.0 6.80 19.0 8.67 0.147 189

60 x 40

3.0 4.35 5.54 26.5 13.9 2.18 1.58 8.82 6.95 10.9 8.19 29.2 11.2 0.192 230

3.2 4.62 5.88 27.8 14.6 2.18 1.57 9.27 7.29 11.5 8.64 30.8 11.7 0.192 217

3.6 5.14 6.54 30.4 15.9 2.16 1.56 10.1 7.93 12.7 9.50 33.8 12.8 0.191 195

4.0 5.64 7.19 32.8 17.0 2.14 1.54 10.9 8.52 13.8 10.3 36.7 13.7 0.190 177

5.0 6.85 8.73 38.1 19.5 2.09 1.50 12.7 9.77 16.4 12.2 43.0 15.7 0.187 146

6.3 8.31 10.6 43.4 21.9 2.02 1.44 14.5 11.0 19.2 14.2 49.5 17.6 0.184 120

80 x 40

3.0 5.29 6.74 54.2 18.0 2.84 1.63 13.6 9.00 17.1 10.4 43.8 15.3 0.232 189

3.2 5.62 7.16 57.2 18.9 2.83 1.63 14.3 9.46 18.0 11.0 46.2 16.1 0.232 178

3.6 6.27 7.98 62.8 20.6 2.81 1.61 15.7 10.3 20.0 12.1 50.8 17.5 0.231 160

4.0 6.90 8.79 68.2 22.2 2.79 1.59 17.1 11.1 21.8 13.2 55.2 18.9 0.230 145

5.0 8.42 10.7 80.3 25.7 2.74 1.55 20.1 12.9 26.1 15.7 65.1 21.9 0.227 119

6.3 10.3 13.1 93.3 29.2 2.67 1.49 23.3 14.6 31.1 18.4 75.6 24.8 0.224 97.2

7.1 11.4 14.5 99.8 30.7 2.63 1.46 25.0 15.4 33.8 19.8 80.9 26.2 0.222 88.0

8.0 12.5 16.0 106 32.1 2.58 1.42 26.5 16.1 36.5 21.2 85.8 27.4 0.219 79.9

90 x 50

3.0 6.24 7.94 84.4 33.5 3.26 2.05 18.8 13.4 23.2 15.3 76.5 22.4 0.272 160

3.2 6.63 8.44 89.1 35.3 3.25 2.04 19.8 14.1 24.6 16.2 80.9 23.6 0.272 151

3.6 7.40 9.42 98.3 38.7 3.23 2.03 21.8 15.5 27.2 18.0 89.4 25.9 0.271 135

4.0 8.15 10.4 107 41.9 3.21 2.01 23.8 16.8 29.8 19.6 97.5 28.0 0.270 123

5.0 9.99 12.7 127 49.2 3.16 1.97 28.3 19.7 36.0 23.5 116 32.9 0.267 100

6.3 12.3 15.6 150 57.0 3.10 1.91 33.3 22.8 43.2 28.0 138 38.1 0.264 81.5

7.1 13.6 17.3 162 60.9 3.06 1.88 36.0 24.4 47.2 30.5 149 40.7 0.262 73.5

8.0 15.0 19.2 174 64.6 3.01 1.84 38.6 25.8 51.4 32.9 160 43.2 0.259 66.5

100 x 50

3.0 6.71 8.54 110 36.8 3.58 2.08 21.9 14.7 27.3 16.8 88.4 25.0 0.292 149

3.2 7.13 9.08 116 38.8 3.57 2.07 23.2 15.5 28.9 17.7 93.4 26.4 0.292 140

3.6 7.96 10.1 128 42.6 3.55 2.05 25.6 17.0 32.1 19.6 103 29.0 0.291 126

4.0 8.78 11.2 140 46.2 3.53 2.03 27.9 18.5 35.2 21.5 113 31.4 0.290 114

5.0 10.8 13.7 167 54.3 3.48 1.99 33.3 21.7 42.6 25.8 135 36.9 0.287 92.8

6.3 13.3 16.9 197 63.0 3.42 1.93 39.4 25.2 51.3 30.8 160 42.9 0.284 75.4

7.1 14.7 18.7 214 67.5 3.38 1.90 42.7 27.0 56.3 33.5 173 46.0 0.282 68.0

8.0 16.3 20.8 230 71.7 3.33 1.86 46.0 28.7 61.4 36.3 186 48.9 0.279 61.4

8.8 17.6 22.5 243 74.8 3.29 1.82 48.5 29.9 65.6 38.5 197 51.1 0.277 56.7

10.0 19.6 24.9 259 78.4 3.22 1.77 51.8 31.4 71.2 41.4 209 53.6 0.274 51.1

100 x 60

3.0 7.18 9.14 124 55.7 3.68 2.47 24.7 18.6 30.2 21.2 121 30.7 0.312 139

3.2 7.63 9.72 131 58.8 3.67 2.46 26.2 19.6 32.0 22.4 129 32.4 0.312 131

3.6 8.53 10.9 145 64.8 3.65 2.44 28.9 21.6 35.6 24.9 142 35.6 0.311 117

4.0 9.41 12.0 158 70.5 3.63 2.43 31.6 23.5 39.1 27.3 156 38.7 0.310 106

5.0 11.6 14.7 189 83.6 3.58 2.38 37.8 27.9 47.4 32.9 188 45.9 0.307 86.5

6.3 14.2 18.1 225 98.1 3.52 2.33 45.0 32.7 57.3 39.5 224 53.8 0.304 70.2

7.1 15.8 20.2 244 106 3.48 2.29 48.8 35.3 62.9 43.2 245 58.0 0.302 63.2

8.0 17.5 22.4 264 113 3.44 2.25 52.8 37.8 68.7 47.1 265 62.2 0.299 57.0

8.8 19.0 24.2 279 119 3.40 2.22 55.9 39.7 73.6 50.2 282 65.4 0.297 52.6

22

H
T

Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued)
Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

120 x 60

3.0 8.12 10.3 194 65.5 4.33 2.52 32.3 21.8 40.0 24.6 156 37.2 0.352 123

3.2 8.64 11.0 205 69.2 4.32 2.51 34.2 23.1 42.4 26.1 165 39.2 0.352 116

3.6 9.66 12.3 227 76.3 4.30 2.49 37.9 25.4 47.2 28.9 183 43.3 0.351 104

4.0 10.7 13.6 249 83.1 4.28 2.47 41.5 27.7 51.9 31.7 201 47.1 0.350 93.7

5.0 13.1 16.7 299 98.8 4.23 2.43 49.9 32.9 63.1 38.4 242 56.0 0.347 76.1

6.3 16.2 20.7 358 116 4.16 2.37 59.7 38.8 76.7 46.3 290 65.9 0.344 61.6

7.1 18.1 23.0 391 126 4.12 2.34 65.2 41.9 84.4 50.8 317 71.3 0.342 55.4

8.0 20.1 25.6 425 135 4.08 2.30 70.8 45.0 92.7 55.4 344 76.6 0.339 49.9

8.8 21.8 27.8 452 142 4.04 2.27 75.3 47.5 99.6 59.2 366 80.8 0.337 45.9

120 x 80

3.6 10.8 13.7 276 147 4.48 3.27 46.0 36.7 55.6 42.0 301 59.5 0.391 92.7

4.0 11.9 15.2 303 161 4.46 3.25 50.4 40.2 61.2 46.1 330 65.0 0.390 83.9

5.0 14.7 18.7 365 193 4.42 3.21 60.9 48.2 74.6 56.1 401 77.9 0.387 68.0

6.3 18.2 23.2 440 230 4.36 3.15 73.3 57.6 91.0 68.2 487 92.9 0.384 54.9

7.1 20.3 25.8 482 251 4.32 3.12 80.3 62.8 100 75.2 535 101 0.382 49.3

8.0 22.6 28.8 525 273 4.27 3.08 87.5 68.1 111 82.6 587 110 0.379 44.3

8.8 24.5 31.3 561 290 4.24 3.04 93.5 72.4 119 88.7 629 117 0.377 40.7

10.0 27.4 34.9 609 313 4.18 2.99 102 78.1 131 97.3 688 126 0.374 36.5

150 x 100 4.0 15.1 19.2 607 324 5.63 4.11 81.0 64.8 97.4 73.6 660 105 0.490 66.4

5.0 18.6 23.7 739 392 5.58 4.07 98.5 78.5 119 90.1 807 127 0.487 53.7

6.3 23.1 29.5 898 474 5.52 4.01 120 94.8 147 110 986 153 0.484 43.2

7.1 25.9 32.9 990 520 5.48 3.97 132 104 163 122 1091 168 0.482 38.7

8.0 28.9 36.8 1087 569 5.44 3.94 145 114 180 135 1203 183 0.479 34.7

8.8 31.5 40.1 1168 610 5.40 3.90 156 122 195 146 1298 196 0.477 31.8

10.0 35.3 44.9 1282 665 5.34 3.85 171 133 216 161 1432 214 0.474 28.4

12.5 42.8 54.6 1488 763 5.22 3.74 198 153 256 190 1679 246 0.468 23.3

160 x 80

4.0 14.4 18.4 612 207 5.77 3.35 76.5 51.7 94.7 58.3 493 88.1 0.470 69.3

5.0 17.8 22.7 744 249 5.72 3.31 93.0 62.3 116 71.1 600 106 0.467 56.0

6.3 22.2 28.2 903 299 5.66 3.26 113 74.8 142 86.8 730 127 0.464 45.1

7.1 24.7 31.5 994 327 5.62 3.22 124 81.7 158 95.9 804 139 0.462 40.4

8.0 27.6 35.2 1091 356 5.57 3.18 136 89.0 175 106 883 151 0.459 36.2

8.8 30.1 38.3 1172 379 5.53 3.15 147 94.9 189 114 949 161 0.457 33.3

10.0 33.7 42.9 1284 411 5.47 3.10 161 103 209 125 1041 175 0.454 29.7

12.5 40.9 52.1 1485 465 5.34 2.99 186 116 247 146 1204 198 0.448 24.5

180 x 60

4.0 14.4 18.4 697 121 6.16 2.56 77.4 40.3 99.8 45.2 341 72.2 0.470 69.3

5.0 17.8 22.7 846 144 6.10 2.52 94.0 48.1 122 54.9 411 86.3 0.467 56.0

6.3 22.2 28.2 1027 171 6.03 2.46 114 57.0 150 66.6 495 102 0.464 45.1

7.1 24.7 31.5 1130 186 5.99 2.43 126 61.9 166 73.3 542 111 0.462 40.4

8.0 27.6 35.2 1240 201 5.94 2.39 138 66.9 184 80.4 590 120 0.459 36.2

8.8 30.1 38.3 1331 212 5.89 2.35 148 70.8 199 86.2 630 127 0.457 33.3

10.0 33.7 42.9 1457 228 5.83 2.30 162 75.8 220 94.4 683 137 0.454 29.7

12.5 40.9 52.1 1682 251 5.68 2.20 187 83.7 260 109 770 151 0.448 24.5

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply

23

Celsius 355 NH Technical Guide Sectional properties Celsius 355 rectangular

H
T

Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued)
Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

180 x 100

4.0

5.0 21.0 26.7 1153 460 6.57 4.15 128 92.0 157 104
1042 154 0.547 47.7

16.9

21.6

945

379

6.61

4.19

105

75.9

128

85.2

852

127

0.550

59.0

6.3 26.1 33.3 1407 557 6.50 4.09 156 111 194 128
1277 186 0.544 38.3

7.1 29.2 37.2 1555 613 6.47 4.06 173 123 215 142
1413 205 0.542 34.2

8.0 32.6 41.6 1713 671 6.42 4.02 190 134 239 157
1560 224 0.539 30.7

8.8 35.6 45.4 1847 720 6.38 3.98 205 144 259 170
1685 240 0.537 28.1

10.0 40.0 50.9 2036 787 6.32 3.93 226 157 288 188
1862 263 0.534 25.0

12.5 48.7 62.1 2385 908 6.20 3.82 265 182 344 223
2191 303 0.528 20.5

200 x 100

4.0

5.0 22.6 28.7 1495 505 7.21 4.19 149 101 185 114
1204 172 0.587 44.3

18.2

23.2

1223

416

7.26

4.24

122

83.2

150

92.8

983

142

0.590

54.9

6.3 28.1 35.8 1829 613 7.15 4.14 183 123 228 140
1475 208 0.584 35.6

7.1 31.4 40.0 2024 674 7.11 4.10 202 135 254 155
1634 229 0.582 31.8

8.0 35.1 44.8 2234 739 7.06 4.06 223 148 282 172
1804 251 0.579 28.5

8.8 38.4 48.9 2412 793 7.02 4.03 241 159 306 186
1950 270 0.577 26.1

10.0 43.1 54.9 2664 869 6.96 3.98 266 174 341 206
2156 295 0.574 23.2

12.5 52.7 67.1 3136 1004 6.84 3.87 314 201 408 245
2541 341 0.568 19.0

14.2 58.9 75.0 3416 1080 6.75 3.80 342 216 450 268
2770 368 0.563 17.0

200 x 120

5.0

6.3 30.1 38.3 2065 929 7.34 4.92 207 155 253 177
2028 255 0.624 33.3

24.1

30.7

1685

762

7.40

4.98

168

127

205

144

1648

210

0.627

41.5

7.1 33.7 42.9 2288 1025 7.30 4.89 229 171 281 197
2252 282 0.622 29.7

8.0 37.6 48.0 2529 1128 7.26 4.85 253 188 313 218
2495 310 0.619 26.6

8.8 41.1 52.4 2734 1215 7.22 4.82 273 203 340 237
2703 334 0.617 24.3

10.0 46.3 58.9 3026 1337 7.17 4.76 303 223 379 263
3001 367 0.614 21.6

12.5 56.6 72.1 3576 1562 7.04 4.66 358 260 455 314
3569 428 0.608 17.7

14.2 63.3 80.7 3907 1693 6.96 4.58 391 282 503 346
3915 464 0.603 15.8

16.0 70.2 89.4 4221 1813 6.87 4.50 422 302 550 377
4247 497 0.599 14.2

200 x 150

5.0

6.3 33.0 42.1 2420 1549 7.58 6.07 242 207 289 237
2947 326 0.684 30.3

26.5

33.7

1970

1265

7.64

6.12

197

169

234

192

2386

267

0.687

37.8

7.1 37.0 47.1 2685 1715 7.55 6.03 268 229 322 264
3280 361 0.682 27.0

8.0 41.4 52.8 2971 1894 7.50 5.99 297 253 359 294
3643 398 0.679 24.1

8.8 45.3 57.7 3217 2047 7.47 5.96 322 273 390 319
3956 430 0.677 22.1

10.0 51.0 64.9 3568 2264 7.41 5.91 357 302 436 356
4409 475 0.674 19.6

12.5 62.5 79.6 4236 2673 7.30 5.80 424 356 525 428
5287 559 0.668 16.0

14.2 70.0 89.2 4644 2919 7.22 5.72 464 389 582 473
5834 610 0.663 14.3

16.0 77.7 99.0 5036 3152 7.13 5.64 504 420 638 518
6370 658 0.659 12.9

220 x 120

5.0

6.3 32.0 40.8 2610 1010 8.00 4.98 237 168 292 191
2315 283 0.664 31.2

25.7

32.7

2125

829

8.06

5.03

193

138

236

155

1881

232

0.667

38.9

7.1 35.9 45.7 2895 1116 7.96 4.94 263 186 326 213
2572 312 0.662 27.9

8.0 40.2 51.2 3203 1229 7.91 4.90 291 205 362 236
2850 343 0.659 24.9

8.8 43.9 55.9 3467 1324 7.87 4.87 315 221 394 256
3089 370 0.657 22.8

10.0 49.4 62.9 3844 1459 7.82 4.81 349 243 440 285
3431 407 0.654 20.2

12.5 60.5 77.1 4560 1707 7.69 4.71 415 285 530 341
4087 476 0.648 16.5

14.2 67.8 86.3 4996 1853 7.61 4.63 454 309 586 376
4488 517 0.643 14.8

16.0 75.2 95.8 5413 1988 7.52 4.55 492 331 643 410
4873 555 0.639 13.3

24

H
T

Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued)
Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

26.5

33.7

2610

618

8.80

4.28

209

124

263

138

1617

217

0.687

37.8

250 x 100

5.0

6.3 33.0 42.1 3207 751 8.73 4.22 257 150 326 169 1983 264 0.684 30.3

7.1 37.0 47.1 3559 827 8.69 4.19 285 165 363 188 2198 291 0.682 27.0

8.0 41.4 52.8 3940 909 8.64 4.15 315 182 404 209 2430 319 0.679 24.1

8.8 45.3 57.7 4266 977 8.60 4.12 341 195 439 226 2627 343 0.677 22.1

0.674 19.6
10.0 51.0 64.9 4733 1072 8.54 4.06 379 214 491 251 2908 376

0.668 16.0
12.5 62.5 79.6 5622 1245 8.41 3.96 450 249 592 299 3436 438

0.663 14.3
14.2 70.0 89.2 6165 1344 8.31 3.88 493 269 655 329 3752 473

0.659 12.9
16.0 77.7 99.0 6686 1433 8.22 3.80 535 287 719 358 4050 505
30.4

38.7

3360

1527

9.31

6.28

269

204

324

228

3278

337

0.787

32.9

250 x 150

5.0

6.3 38.0 48.4 4143 1874 9.25 6.22 331 250 402 283 4054 413 0.784 26.3

7.1 42.6 54.2 4606 2078 9.22 6.19 368 277 449 315 4515 457 0.782 23.5

8.0 47.7 60.8 5111 2298 9.17 6.15 409 306 501 350 5021 506 0.779 21.0

8.8 52.2 66.5 5546 2486 9.13 6.12 444 331 545 381 5457 547 0.777 19.2

0.774 17.0
10.0 58.8 74.9 6174 2755 9.08 6.06 494 367 611 426 6090 605

0.768 13.8
12.5 72.3 92.1 7387 3265 8.96 5.96 591 435 740 514 7326 717

14.2 81.1 103 8141 3576 8.87 5.88 651 477 823 570 8102 784 0.763 12.3

16.0 90.3 115 8879 3873 8.79 5.80 710 516 906 625 8868 849 0.759 11.1
30.4

38.7

3532

1354

9.55

5.91

272

193

331

216

3078

326

0.787

32.9

260 x 140

5.0

6.3 38.0 48.4 4355 1660 9.49 5.86 335 237 411 267 3803 399 0.784 26.3

7.1 42.6 54.2 4842 1839 9.45 5.82 372 263 459 298 4234 442 0.782 23.5

8.0 47.7 60.8 5373 2032 9.40 5.78 413 290 511 331 4704 488 0.779 21.0

8.8 52.2 66.5 5831 2197 9.37 5.75 449 314 557 360 5110 527 0.777 19.2

0.774 17.0
10.0 58.8 74.9 6490 2432 9.31 5.70 499 347 624 402 5698 584

0.768 13.8
12.5 72.3 92.1 7767 2876 9.18 5.59 597 411 756 485 6841 690

14.2 81.1 103 8560 3144 9.10 5.52 658 449 840 537 7555 754 0.763 12.3

16.0 90.3 115 9337 3400 9.01 5.44 718 486 925 588 8257 815 0.759 11.1

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply

25

Celsius 355 NH Technical Guide Sectional properties Celsius 355 rectangular

H
T

Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued)
Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

300 x 100

5.0

6.3 38.0 48.4 5111 890 10.3 4.29 341 178 439 199 2504 319 0.784 26.3

30.4

38.7

4146

731

10.3

4.34

276

146

354

161

2040

262

0.787

32.9

7.1 42.6 54.2 5683 981 10.2 4.25 379 196 490 221 2775 352 0.782 23.5

8.0 47.7 60.8 6305 1078 10.2 4.21 420 216 546 245 3069 387 0.779 21.0

8.8 52.2 66.5 6841 1160 10.1 4.18 456 232 594 266 3319 416 0.777 19.2

10.0 58.8 74.9 7613 1275 10.1 4.13 508 255 666 296 3676 458 0.774 17.0

12.5 72.3 92.1 9103 1486 9.94 4.02 607 297 806 354 4350 534 0.768 13.8

14.2 81.1 103 10028 1607 9.85 3.94 669 321 896 390 4755 578 0.763 12.3

16.0 90.3 115 10931 1719 9.75 3.87 729 344 986 425 5138 619 0.759 11.1

300 x 200

5.0

6.3 47.9 61.0 7829 4193 11.3 8.29 522 419 624 472 8476 681 0.984 20.9

38.3

48.7

6322

3396

11.4

8.35

421

340

501

380

6824

552

0.987

26.1

7.1 53.7 68.4 8729 4667 11.3 8.26 582 467 698 528 9469 757 0.982 18.6

8.0 60.3 76.8 9717 5184 11.3 8.22 648 518 779 589
10562 840 0.979 16.6

8.8 66.0 84.1 10573 5631 11.2 8.18 705 563 851 643
11514 912 0.977 15.2

10.0 74.5 94.9 11819 6278 11.2 8.13 788 628 956 721
12908
1015 0.974 13.4

12.5 91.9 117 14273 7537 11.0 8.02 952 754 1165 877
15677
1217 0.968 10.9

14.2 103 132 15832 8328 11.0 7.95 1055 833 1302 978
17457 1343 0.963 9.67

16.0 115 147 17390 9109 10.9 7.87 1159 911 1441
1080
19252 1468 0.959 8.67

300 x 250

5.0

6.3 52.8 67.3 9188 6950 11.7 10.2 613 556 716 633
12155 862 1.08 18.9

42.2

53.7

7410

5611

11.7

10.2

494

449

575

508

9766

697

1.09

23.7

7.1 59.3 75.5 10252 7749 11.6 10.1 683 620 802 708
13595 960 1.08 16.9

8.0 66.5 84.8 11422 8627 11.6 10.1 761 690 896 791
15187 1067 1.08 15.0

8.8 72.9 92.9 12439 9388 11.6 10.1 829 751 979 864
16578 1160 1.08 13.7

10.0 82.4 105 13923 10496 11.5 10.0 928 840 1101 971
18620
1295 1.07 12.1

12.5 102 130 16857 12680 11.4 9.89 1124 1014 1345 1185
22711 1560 1.07

9.83

14.2 115 146 18734 14070 11.3 9.82 1249 1126 1505 1325
25365 1728 1.06

8.73

16.0 128 163 20620 15460 11.2 9.74 1375 1237 1668 1467
28064 1896 1.06

7.81

340 x 100 10.0 65.1 82.9 10585 1438 11.3 4.16 623 288 823 332 4299 523 0.854 15.4
350 x 150

5.0

6.3 47.9 61.0 9481 2525 12.5 6.43 542 337 676 373 6389 586 0.984 20.9

38.3

48.7

7655

2053

12.5

6.49

437

274

543

301

5161

477

0.987

26.1

7.1 53.7 68.4 10572 2803 12.4 6.40 604 374 756 416 7122 651 0.982 18.6

8.0 60.3 76.8 11770 3105 12.4 6.36 673 414 844 464 7926 721 0.979 16.6

8.8 66.0 84.1 12808 3364 12.3 6.33 732 449 922 506 8622 781 0.977 15.2

10.0 74.5 94.9 14320 3737 12.3 6.27 818 498 1035 566 9633 867 0.974 13.4

12.5 91.9 117 17297 4450 12.2 6.17 988 593 1263 686
11619
1032 0.968 10.9

14.2 103 132 19189 4890 12.1 6.09 1097 652 1411 763
12875 1134 0.963 9.67

16.0 115 147 21079 5317 12.0 6.01 1205 709 1561 840
14124 1233 0.959 8.67

350 x 250

6.3

7.1 64.9 82.6 14747 8796 13.4 10.3 843 704 999 794
17024 1127 1.18 15.4

57.8

73.6

13203

7885

13.4

10.4

754

631

892

709

15215

1011

1.18

17.3

8.0 72.8 92.8 16449 9798 13.3 10.3 940 784 1118 888
19027 1254 1.18 13.7

8.8 79.8 102 17932 10668 13.3 10.2 1025 853 1222 970
20778 1365 1.18 12.5

10.0 90.2 115 20102 11937 13.2 10.2 1149 955 1375
1091
23354 1525 1.17 11.1

12.5 112 142 24419 14444 13.1 10.1 1395 1156 1685 1334
28526 1842 1.17

8.97

14.2 126 160 27200 16046 13.0 10.0 1554 1284 1887 1492
31892 2044 1.16

7.95

16.0 141 179 30011 17654 12.9 9.93 1715 1412 2095 1655
35325 2246 1.16

7.12

26

H
T

Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued)
Size

Thickness Mass Sectional


H x B
mm

area
A

Moment

Radius

Elastic

Plastic

Torsional

of inertia

of gyration

modulus

modulus

constants

Superficial Approx
area/m

length

Iyy Izz iyy izz Wel,yy Wel,zz Wpl,yy Wpl,zz It Ct As /tonne

mm kg/m cm2 cm4 cm4 cm cm cm3 cm3 cm3 cm3 cm4 cm3 m2/m m/t

400 x 150

6.3

7.1 59.3 75.5 14794 3166 14.0 6.47 740 422 936 467 8467 748 1.08 16.9

52.8

67.3

13255

2851

14.0

6.51

663

380

836

418

7595

673

1.08

18.9

8.0 66.5 84.8 16488 3509 13.9 6.43 824 468 1046 521 9424 828 1.08

8.8 72.9 92.9 17961 3804 13.9 6.40 898 507 1143 568
10254 898 1.08 13.7

15.0

10.0 82.4 105 20111 4227 13.8 6.35 1006 564 1285 636
11460 998 1.07 12.1

12.5 102 130 24369 5043 13.7 6.24 1218 672 1571 772
13831 1190 1.07 9.83

14.2 115 146 27095 5547 13.6 6.16 1355 740 1758 859
15333 1309 1.06 8.73

16.0 128 163 29836 6038 13.5 6.09 1492 805 1948 947
16829 1426 1.06 7.81

400 x 200

6.3

7.1 64.9 82.6 17535 5989 14.6 8.51 877 599 1075 665
14096 1021 1.18 15.4

57.8

73.6

15696

5376

14.6

8.55

785

538

960

594

12612

917

1.18

17.3

8.0 72.8 92.8 19562 6660 14.5 8.47 978 666 1203 743
15735 1135 1.18 13.7

8.8 79.8 102 21328 7241 14.5 8.44 1066 724 1315 811
17164 1233 1.18 12.5

10.0 90.2 115 23914 8084 14.4 8.39 1196 808 1480 911
19259 1376 1.17 11.1

12.5 112 142 29063 9738 14.3 8.28 1453 974 1813
1111
23438 1656 1.17 8.97

14.2 126 160 32381 10784 14.2 8.21 1619 1078 2032 1242
26137 1834 1.16

7.95

16.0 141 179 35738 11824 14.1 8.13 1787 1182 2256 1374
28871 2010 1.16

7.12

400 x 300

8.0

8.8 93.6 119 28063 18037 15.3 12.3 1403 1202 1659 1363
33908 1906 1.38

85.4

109

25709

16540

15.4

12.3

1285

1103

1517

1247

31014

1749

1.38

11.7
10.7

10.0 106 135 31521 20233 15.3 12.2 1576 1349 1870 1536
38180 2135 1.37

9.44

12.5 131 167 38451 24611 15.2 12.1 1923 1641 2298 1884
46810 2592 1.37

7.62

14.2 148 189 42954 27441 15.1 12.1 2148 1829 2579 2113
52472 2887 1.36

6.76

16.0 166 211 47541 30309 15.0 12.0 2377 2021 2870 2349
58286 3184 1.36

6.04

450 x 250

8.0

8.8 93.6 119 32840 13229 16.6 10.5 1460 1058 1774 1182
29590 1774 1.38

85.4

109

30082

12142

16.6

10.6

1337

971

1622

1081

27083

1629

1.38

11.7
10.7

10.0 106 135 36895 14819 16.5 10.5 1640 1185 2000 1331
33284 1986 1.37

9.44

12.5 131 167 45026 17973 16.4 10.4 2001 1438 2458 1631
40719 2406 1.37

7.62

14.2 148 189 50315 19999 16.3 10.3 2236 1600 2759 1827
45577 2675 1.36

6.76

16.0 166 211 55705 22041 16.2 10.2 2476 1763 3070 2029
50545 2947 1.36

6.04

500 x 200 8.0 85.4 109 34045 8135 17.7 8.65 1362 814 1707 896
21124 1430 1.38 11.7

8.8 93.6 119 37167 8850 17.7 8.61 1487 885 1867 979
23048 1555 1.38 10.7

10.0 106 135 41755 9891 17.6 8.56 1670 989 2105
1101
25872 1737 1.37 9.44

12.5 131 167 50956 11938 17.5 8.45 2038 1194 2586 1346
31514 2096 1.37

7.62

14.2 148 189 56939 13239 17.4 8.38 2278 1324 2904 1505
35166 2324 1.36

6.76

16.0 166 211 63036 14539 17.3 8.30 2521 1454 3231 1669
38872 2552 1.36

6.04

500 x 300

8.0

10.2

97.9

125

43728

19951

18.7

12.6

1749

1330

2100

1480

42563

2203

1.58

8.8 107 137 47784 21770 18.7 12.6 1911 1451 2300 1619
46554 2403 1.58

9.31

10.0 122 155 53762 24439 18.6 12.6 2150 1629 2595 1826
52450 2696 1.57

8.22

12.5 151 192 65813 29780 18.5 12.5 2633 1985 3196 2244
64389 3281 1.57

6.63

14.2 170 217 73700 33245 18.4 12.4 2948 2216 3593 2519
72244 3660 1.56

5.87

16.0 191 243 81783 36768 18.3 12.3 3271 2451 4005 2804
80329 4044 1.56

5.24

20.0 # 235 300 98777 44078 18.2 12.1 3951 2939 4885 3408
97447 4842 1.55

4.25

SAW Process (single longitudinal seam weld, slightly proud)

The dimensions shown in blue are standard sizes and should be given preference
All other sizes are non-standard and therefore minimum order quantities may apply

27

www.tatasteel.com

While care has been taken to ensure that the


information contained in this brochure is accurate,
neither Tata Steel Europe Limited, nor its subsidiaries,
accept responsibility or liability for errors or for
information which is found to be misleading.
Copyright 2013
Tata Steel Europe Limited

Tata Steel
PO Box 101
Weldon Road
Corby
Northants
NN17 5UA
United Kingdom
T: +44 (0)1536 404561
F: +44 (0)1536 404111
marketing@tatasteel.com
English Language TST55:1000:UK:09/2013

S-ar putea să vă placă și