0 evaluări0% au considerat acest document util (0 voturi)
140 vizualizări13 pagini
The document provides sample exam questions and answers for CCNA 1 Chapter 1 and Chapter 2. It tests knowledge of networking fundamentals like different internet connection types, network devices, network security goals, and initial switch configuration procedures. It also includes questions on router configuration files, IPv4 addressing schemes, and CLI commands and shortcuts.
The document provides sample exam questions and answers for CCNA 1 Chapter 1 and Chapter 2. It tests knowledge of networking fundamentals like different internet connection types, network devices, network security goals, and initial switch configuration procedures. It also includes questions on router configuration files, IPv4 addressing schemes, and CLI commands and shortcuts.
The document provides sample exam questions and answers for CCNA 1 Chapter 1 and Chapter 2. It tests knowledge of networking fundamentals like different internet connection types, network devices, network security goals, and initial switch configuration procedures. It also includes questions on router configuration files, IPv4 addressing schemes, and CLI commands and shortcuts.
1. Which two Internet solutions provide an always-on, high-bandwidth connection to computers on a LAN? (Choose two.) cellular DSL satellite cable dial-up telephone 2. What type of network must a home user access in order to do online shopping? a local area network the Internet an extranet an intranet 3. What are two functions of intermediary devices on a network? (Choose two.) They are the primary source and providers of information and services to end devices. They form the interface between the human network and the underlying communication network. They direct data along alternate pathways when there is a link failure. They run applications that support collaboration for business. They filter the flow of data, based on security settings. 4. Fill in the blank. The acronym BYOD refers to the trend of end users being able to use their personal devices to access the business network and resources. 5. Which description correctly defines a converged network? a network that allows users to interact directly with each other over multiple channels a network that is limited to exchanging character-based information a dedicated network with separate channels for video and voice services a single network channel capable of delivering multiple communication forms 6. Drag and drop Match each characteristic to its corresponding internet conectivity type.
satellite -> Not suited for heavily wooded areas dialup telephone -> typically has very low bandwidth DSL -> splits the access line into three signals cable -> uses coaxial cable as a medium 7. Drag and drop Match the form of network communication with its description.
Web pages that groups of people can edit and view together -> wiki Interactive websites where people created and share user-generated content with friends and family ->Social media real-time communication of between two or more people -> instant messaging an audio-based medium that allows people to deliver their recordings to a wide audience -> podcast 8. Drag and drop Match each definition to the corresponding security goal:
maintaining integrity -> the assurance that the information has not been altered during transmission ensuring confidentiality -> only the intended recipients can access and read the data ensuring availability -> the assurance of timely and reliable access to data 9. Which statement describes a characteristic of cloud computing? A business can connect directly to the Internet without the use of an ISP. Devices can connect to the Internet through existing electrical wiring. Investment in new infrastructure is required in order to access the cloud. Applications can be accessed over the Internet through a subscription. 10. Which two Internet connection options do not require that physical cables be run to the building? (Choose two.) cellular dialup satellite DSL dedicated leased line 11. What is a characteristic of circuit-switched networks? A single message can be broken into multiple message blocks that are transmitted through multiple circuits simultaneously. If all circuits are busy, a new call cannot be placed. If a circuit fails, the call will be forwarded on a new path. Circuit-switched networks can dynamically learn and use redundant circuits. 12. Requiring strong, complex passwords is a practice that supports which network security goal? maintaining communication integrity ensuring redundancy ensuring data confidentiality ensuring reliability of access 13. What two criteria are used to help select network media? (Choose two.) the distance the media can successfully carry a signal the environment where the media is to be installed the cost of the end devices utilized in the network the number of intermediary devices installed in the network the types of data that need to be prioritized 14. Which statement describes a network that supports QoS? Data sent over the network is not altered in transmission. The fewest possible devices are affected by a failure. The network provides predictable levels of service to different types of traffic. The network should be able to expand to keep up with user demand. 15.
Refer to the exhibit. Which set of devices contains only intermediary devices? A, B, E, F A, B, D, G G, H, I, J C, D, G, I 16. Which device performs the function of determining the path that messages should take through internetworks? a web server a DSL modem a router a firewall 17. Which tool provides real-time video and audio communication over the Internet so that businesses can conduct corporate meetings with participants from several remote locations? wiki instant messaging weblog TelePresence 18. Which two statements about the relationship between LANs and WANs are true? (Choose two.) Both LANs and WANs connect end devices. WANs are typically operated through multiple ISPs, but LANs are typically operated by single organizations or individuals. WANs connect LANs at slower speed bandwidth than LANs connect their internal end devices. The Internet is a WAN. WANs must be publicly-owned, but LANs can be owned by either public or private entities. 19. Which three network tools provide the minimum required security protection for home users? (Choose three.) antivirus software antispyware software an intrusion prevention system powerline networking a firewall access control lists 20. Which area of the network would a college IT staff most likely have to redesign as a direct result of many students bringing their own tablets and smartphones to school to access school resources? intranet wired LAN wireless LAN extranet wireless WAN 21. Which expression accurately defines the term congestion? a method of limiting the impact of a hardware or software failure on the network a set of techniques to manage the utilization of network resources a state where the demand on the network resources exceeds the available capacity a measure of the data carrying capacity of the network
CCNA 1 Chapter 2 v5.0 Exam Answers 2014 1.
Refer to the exhibit. A switch was configured as shown. A ping to the default gateway was issued, but the ping was not successful. Other switches in the same network can ping this gateway. What is a possible reason for this? The default gateway address must be 192.168.10.1. The ip default-gateway command has to be issued in the VLAN interface configuration mode. The VLAN IP address and the default gateway IP address are not in the same network. The no shutdown command was not issued for VLAN 1. The local DNS server is not functioning correctly. 2. While trying to solve a network issue, a technician made multiple changes to the current router configuration file. The changes did not solve the problem and were not saved. What action can the technician take to discard the changes and work with the file in NVRAM? Issue the reload command without saving the running configuration. Close and reopen the terminal emulation software. Delete the vlan.dat file and reboot the device. Issue the copy startup-config running-config command. 3. Why is it important to configure a hostname on a device? to allow local access to the device through the console port a Cisco router or switch only begins to operate when its hostname is set to identify the device during remote access (SSH or telnet) a hostname must be configured before any other parameters 4. Which procedure is used to access a Cisco 2960 switch when performing an initial configuration in a secure environment? Use the console port to locally access the switch from a serial or USB interface of the PC. Use Secure Shell to remotely access the switch through the network. Use Telnet to remotely access the switch through the network. Use the AUX port to locally access the switch from a serial or USB interface of the PC. 5. What criterion must be followed in the design of an IPv4 addressing scheme for end devices? Each local host should be assigned an IP address with a unique network component. Each IP address must match the address that is assigned to the host by DNS. Each IP address must be unique within the local network. Each IP address needs to be compatible with the MAC address. 6. A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a switch to manage it. Which access method should be chosen? AUX SSH Console Telnet 7. Which interface allows remote management of a Layer 2 switch? the switch virtual interface the console port interface the AUX interface the first Ethernet port interface 8. What is a result of using the service password-encryption command on a Cisco network device? All passwords in the configuration are not shown in clear text when viewing the configuration. The command encrypts the banner message. The command encrypts the enable mode password. A network administrator who later logs into the device will be required to enter an administrator password in order to gain access to the Cisco device. 9. Match the difinitions to their respective CLI hot keys and shortcuts.
Tab -> Completes abbreviated commands and parameters Ctrl-R -> Redisplays, on a new line, the command currently being typed Up Arrow -> scrolls backwards through previously entered commands Ctrl-Z -> returns directly to the privileged EXEC mode Ctrl-C -> cancels any command currently being entered and returns directly to privileged EXEC mode 10. A network administrator is planning an IOS upgrade on several of the head office routers and switches. Which three questions must be answered before continuing with the IOS selection and upgrade? (Choose three.) What models of routers and switches require upgrades? Do the routers and switches have enough RAM and flash memory for the proposed IOS versions? What ports are installed on the routers and switches? Are the devices on the same LAN? What features are required for the devices? Do the devices have enough NVRAM to store the IOS image? 11. What benefit does DHCP provide to a network? Hosts can connect to the network and get an IP address without manual configuration. Duplicate addresses cannot occur on a network that issues dynamic addresses using DHCP and has static assignments. DHCP allows users to refer to locations by a name rather than an IP address. Hosts always have the same IP address and are therefore always reachable. 12. Which two functions are provided to users by the context-sensitive help feature of the Cisco IOS CLI? (Choose two.) providing an error message when a wrong command is submitted allowing the user to complete the remainder of an abbreviated command with the TAB key displaying a list of all available commands within the current mode selecting the best command to accomplish a task determining which option, keyword, or argument is available for the entered command
13. A router has a valid operating system and a configuration stored in NVRAM. When the router boots up, which mode will display? global configuration mode user EXEC mode setup mode ROM monitor mode 14. Which two features are characteristics of flash memory? (Choose two.) Flash receives a copy of the IOS from RAM when a device is powered on. Flash provides nonvolatile storage. The contents of flash may be overwritten. Flash is a component in Cisco switches but not in Cisco routers. The contents of flash may be lost during a power cycle. 15. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.) boot IOS mode Ethernet interface privileged EXEC mode VTY interface console interface router configuration mode 16. Why would a Layer 2 switch need an IP address? to enable the switch to send broadcast frames to attached PCs to enable the switch to function as a default gateway to enable the switch to receive frames from attached PCs to enable the switch to be managed remotely
17. What is a user trying to determine when issuing a ping 10.1.1.1 command on a PC? if there is connectivity with the destination device what type of device is at the destination if the TCP/IP stack is functioning on the PC without putting traffic on the wire the path that traffic will take to reach the destination 18. What command can be used on a Windows PC to see the IP configuration of that computer? ping show interfaces show ip interface brief ipconfig 19. Which statement is true about the running configuration file in a Cisco IOS device? It should be deleted using the erase running-config command. It is automatically saved when the router reboots. It affects the operation of the device immediately when modified. It is stored in NVRAM.
20. Match the description to the common IOS CLI access method.
21. Which two characters are allowed as part of the hostname of a Cisco device? (Choose two.) tab space question mark numbers underline 22. A new network administrator has been asked to enter a banner message on a Cisco device. What is the fastest way a network administrator could test whether the banner is properly configured? Power cycle the device. Enter CTRL-Z at the privileged mode prompt. Exit global configuration mode. Exit enable mode and press Enter. Reboot the device.