Documente Academic
Documente Profesional
Documente Cultură
on the machine.
Turn off any firewalls for debugging. If the firewall is the problem, you'll have to
configure it to allow access to "trusted zone" addresses. Note that some firewalls must be
completely uninstalled to stop them from affecting your networking.
Hold the Windows key and press R, then type CMD to open a command prompt.
In the command prompt window that opens, type type the following commands:
PING each remote computer by IP address, and if successful, PING by name. Open a
command prompt as described above and type.
Where:
<ip address> - is the x.x.x.x IP address
<computer name> - is the computer name
Note: You can obtain the IP address and computer name of a computer by opening a
command prompt (DOS window) and typing IPCONFIG /ALL. This should work for any
Windows version. The IPCONFIG /ALL display will provide a wealth of useful
information for debugging your network connection.
Note: You can check the services in Control Panel, Administrative Tools, Services.
All of these services should be started, and their startup type should be automatic.
All computers should be in the same workgroup for computer browsing to function
properly. File & Print Sharing has to be enabled on any computer you wish to share files
or printers from. You also need to actually share the resource in question from My
Computer, right click on the drive/printer/folder, and select sharing.
While the default NetBIOS setting is correct for normal network configurations, it's
possible for it to be altered, and it costs nothing to make sure it's correct. NETBIOS over
TCP/IP must be enabled for normal network browsing.
http://support.microsoft.com/?id=257844
You can use this procedure to create both sides of a two-way, external trust. You must
have administrative credentials for your domain as well as for the reciprocal domain. If
you have administrative credentials only for your domain, you can use the procedure
Create aTwo-Way, External Trust for One Side of the Trust to create your side of the
trust. Then, have the administrator for the reciprocal domain create a two-way, external
trust from his or her domain.
A two-way, external trust allows users in your domain (the domain that you are logged on
to at the time that you run the New Trust Wizard) and users in the reciprocal domain to
access resources in either of the two domains.
You can create this external trust by using the New Trust Wizard in the Active Directory
Domains and Trusts snap-in or by using the Netdom command-line tool. For more
information about using the Netdom command-line tool to create an external trust, see
Netdom Overview (http://go.microsoft.com/fwlink/?LinkId=111537).
For more information about the selections that are available on the Direction of
Trust page, see "Direction of Trust" in Appendix: New Trust Wizard Pages.
7. On the Sides of Trust page, click Both this domain and the specified domain,
and then click Next.
For more information about the selections that are available on the Sides of Trust
page, see "Sides of Trust" in Appendix: New Trust Wizard Pages.
8. On the User Name and Password page, type the user name and password for the
appropriate administrator in the specified domain.
9. On the Outgoing Trust Authentication Level--Local Domain page, do one of
the following, and then click Next:
o Click Domain-wide authentication.
o Click Selective authentication.
10. On the Outgoing Trust Authentication Level--Specified Domain page, do one
of the following, and then click Next:
o Click Domain-wide authentication.
o Click Selective authentication.
11. On the Trust Selections Complete page, review the results, and then click Next.
12. On the Trust Creation Complete page, review the results, and then click Next.
13. On the Confirm Outgoing Trust page, do one of the following:
o If you do not want to confirm this trust, click No, do not confirm the
outgoing trust. Note that if you do not confirm the trust at this stage, the
secure channel will not be established until the first time that the trust is
used by users.
o If you want to confirm this trust, click Yes, confirm the outgoing trust,
and then supply the appropriate administrative credentials from the
specified domain.
14. On the Confirm Incoming Trust page, do one of the following:
o If you do not want to confirm this trust, click No, do not confirm the
incoming trust.
o If you want to confirm this trust, click Yes, confirm the incoming trust,
and then supply the appropriate administrative credentials from the
specified domain.
15. On the Completing the New Trust Wizard page, click Finish.