Sunteți pe pagina 1din 10

X360Run1.

1 (Slim+ Trinity) Glitcher Board Instruction


.The theory of X360Run Glitcher Board
The X360Run send out a confirm width of pulse to XBOX360 slim
machine. For different type XBOX360 slim machine have different type
pulse time point and width.

.The X360Run Glitcher Board and trimming switch:


.Configuration and trimming description
The user must choose a different configuration options according
to the different type XBOX360 slim machine.
The user can use the factory default setting of the X360Run
Glitcher board.the user can use the trimmability switch to get a
better time pulse,and this change will make XBOX360 machine achieve
the best effective.



Please choice default setting in the following three tableother
setting only for test by user choicePlease use Corona Mode 1 for
Corona machine of Toshiba NandFlash on board and produced after Nov.
2013(need change the Windbond memory chip first)
The Corona Mode2 for test by user choice
The Compatible and function of Corona X360run Yellow-Board Mode
same as X360Run Yellow Board
X360Run Glitcher board have four type switch and trimming
adjustable setting:
(S: short the jumper pad , O:open the jumper pad)

1. The XBOX360 slim machine type setting

XBOX360
Type
Timing
pulse
M2 M1 M0
Monolithic
capacitor
CD
Ceramics
capacitors
CO
Command
Corona forward S S S
330P 15P
Corona default S S O
330P 15P
Corona
Mode 1

Corona
Add-ons
delay
S O S
330P 15P
Corona default S O O 330P 15P
Corona
Mode 2


Trinity10.83A default O S S 150P 20P
Trinity9.6A default O S O 220P 25P
Corona
Add-ons
delay
O O S
330P 15P
Corona default O O O 330P 15P
Compatible
X360Run
Yellow-Board
Mode

According to the different type XBOX360 machine , set the according
M0,M1,M2 jumper pad with S or O follow this table. The value of capacitors
about CD and CO must set correct too . the factory default value is Corona
Mode 1:SSO.



2. Pulse time delay trimming setting

Delay trimming D2 D1 D0 unit
O S S -3
O S O -2
O O S -1
O O O default
Corona Mode 1;
Compatible X360Run
Yellow-Board Corona
Mode
S S S +1
Trinity 10.83A
Trinity 9.6A
S S O +2
Corona Mode 2 S O S +3
S O O +4

The pulse time can be adjust to forward(forth:-1~-3) or
backward(back:+1~+4) on the basis of the standard value.
According to the different type XBOX360 machine, set the
according D0,D1,D2 jumper pad with S or O follow this table. the
factory default value is Corona Mode 1/X360Run Yellow-Board Corona
Mode:SSS(+1).

3. Pulse width trimming setting

width trimming W2 W1 W0 unit
O S S -3
O S O -2
Trinity 10.83A O O S -1
Trinity 9.6A
Corona Mode 2
O O O default
S S S +1
Corona Mode 1;
Compatible X360Run
Yellow-Board Corona
Mode
S S O +2
S O S +3
S O O +4

The pulse width can be adjust to forward(forth:-1~-3) or backward
(back:+1~+4) on the basis of the standard value.
According to the different type XBOX360 machine, set the according
W0,W1,W2 jumper pad with S or O follow this table. the factory
default value is Corona Mode 1/X360Run Yellow-Board Corona
Mode:SSO(+2).


4. The adjustment of resistance and capacitance in the pulse signal output

The D pin of X360Run Glitcher board is pulse signal output, can
reduce the pulse signal strength by series resistance, the factory
default value is 8.2.
The D pin of X360Run Glitcher board is pulse signal output, can
produce an effect on launch XBOX360 slim machine succeed by shunt-wound
differences value of Monolithic capacitance, the factory default value
is CD=330pf(Corona),CD=220pf(Trinity9.6A) or CD=150pf(Trinity10.83A)
The length of two pins about CD capacitance dont cut to short
The length of CD capacitance about 1.5cm-1.7cm.
Attention!: if replace Monolithic capacitance,must weld the new
Monolithic capacitance complete before launch XBOX360 slim machine
again.

5.Wire Install

X360Run Glitcher board have SIX wire to be connectedthem are:

1. Power Wire: VDD,
2. Ground Wire: GND,
3. I2C_SCL(E),
4. I2C_SDA(F),
5. POST_OUT(C),
6. CPU_RST(D)

For Corona and Trinity 9.6A

The 14 Wire direct connect to Glitcher boardabout 10cm

The 5-6 Wire direct connect to Glitcher boardabout 4cm to 7cm.can
adjustment the length of 5-6 Wire in 4cm to 7cm carefully,then get the
best effect.

For Trinity 10.83A

The 14 Wire direct connect to Glitcher boardabout 10cm

The 5 Wire direct connect to Glitcher boardabout 4cm to 7cm.can
adjustment the length of 5 Wire in 4cm to 7cm carefully,then get the
best effect.
The 6 Wire direct connect to Glitcher boardabout 4cm to 15cm(12cm is
typical value).can adjustment the length of 6 Wire in 4cm to 15cm
carefully,then get the best effect.



Attention!:
After modify the Xbox360 Trinity 10.83A machine,Must open and close
10 times to 20 times to check Whether or not Red-led on panel is Lights
up.if Red-led is Lights up,Can connect D point to GND point on X360Run
PCB Board with a 10K-20K metal-wire Resistor.

.The weld of changed XBOX360 slim machine
1. Corona-V1, Corona-V2























2. Corona-V3, Corona-V4Corona-V5Corona-V6




3.Trinity








. Debug and install









CPU_CtoC wire
CPU_DtoD wire

The shunt-wound Monolithic capacitance CD [330pf(Corona) or
220pf(Trinity)],one pin weld to C1 point, another pin weld to a point
between D point and C2 point.

The length of two pins about CD capacitance dont cut to short.

GND
3.3V
CPU_C
CPU_E
CPU_F
CPU_D
CD
C1
C2
CO


. Typical application
Corona Mode 1be fit for CoronaInclude the Xbox360 machine produced
after Nov. 2013 and Corona machine of Toshiba NandFlash on board
XBOX360
Type
Timing
pulse
M2 M1 M0
Corona default S S O
Delay
trimming
D2 D1 D0 unit
S S S +1
width
trimming
W2 W1 W0 unit
S S O +2
Attention!:
The Xbox360 machine of Windbond memory on board produced after Nov.
2013,need change the Windbond memory chip first.

Corona Mode 2be fit for Coronafor test by user choice
XBOX360
Type
Timing
pulse
M2 M1 M0
Corona default S O O
Delay
trimming
D2 D1 D0 unit
S O S +3
width
trimming
W2 W1 W0 unit
O O O default
Attention!:
The Xbox360 machine of Windbond memory on board produced after Nov.
2013,need change the Windbond memory chip first.

Compatible X360Run Yellow-Board Corona Modebe fit for CoronaNot
include the Xbox360 machine of Toshiba NandFlash on board and Corona of
change the Windbond memory chip first.
XBOX360
Type
Timing
pulse
M2 M1 M0
Corona default O O O
Delay
trimming
D2 D1 D0 unit
S S S +1
width
trimming
W2 W1 W0 unit
S S O +2

S-ar putea să vă placă și