Copyright statement Ruijie Networks2000-2010 Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
are registered trademarks of Ruijie Networks. Counterfeit is strictly prohibited.
Exemption statement
This document is provided !as is". The contents of this document are subject to change without any notice. Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.
Preface Thank you for using our switches. This manual(Version1.4) will guide you through the installation and use of switches. Scope This manual introduces functional and physical features of our switches and provides installation procedures, troubleshooting, technical specifications, and rules of using cables and connectors. It is intended for the users who have some experience in installing and maintaining network hardware and want to learn the above information. This manual assumes that users are familiar with Ethernet terms and concepts. Document Structure n Chapter 1 !Overview" describes applications, main features, technical specifications, and related extension modules of the product. n Chapter 2 !Preparation Before Installation" lists safety, power supply, and site requirements that must be met before you install the switch. n Chapter 3 !Installation" describes how to install the switch as a whole and its various modules, and connect power supply and grounding cables. n Chapter 4 !Maintenance" describes how to maintain the switch in use. n Chapter 5 !Troubleshooting" describes the problems that may occur during the installation and use of this switch and the ways to solve these problems. n Appendix A !Connectors and Connection Media". n Appendix B !Mini-GBIC and 10G XENPAK Module". Related Documents Software Manual: Covers CLI commands, configuration guide, version release notes, and system messages. Obtaining Documentation You can obtain the documentation you need through the following channels: Internet: You can obtain the latest on-line documentation at:http://www.ruijie.com.cn
Documentation CD-ROM: The documentation of Ruijie Networks switches is stored in the CD-ROM package, which is provided to you together with the product you purchase. The CD-ROM is updated frequently, and may be more current than the printed documents. Obtaining Technical Assistance Ruijie Networks provides excellent technical support services for all our products. You can obtain the technical assistance you need through any of the following channels:
n Website of Ruijie Networks from which you can obtain the latest product documentation, causes and problems analysis of product faults, application solutions, and software upgrade. n Customer service center of Ruijie Networks Customer Service Center of Ruijie Network provides all customers with needed technical assistance: product, technology and solutions. The customer service center provides responsive technical support for your product installation problems, software configuration problems, and other network performance problems. n Technical support hot-line: +86-4008-111-000. n Technical support webpage: http://www.ruijie.com.cn n Technical support E-mail: service@ruijie.com.cn Documentation Conventions The symbols used in this document are described as below:
Note This symbol brings your attention. It includes some helpful suggestions and references.
Warning This symbol means that you must be extremely careful. It reminds you to avoid behaviors that can bring data loss and cause damage to a device.
1.6.20 RG-PD1200/ PD2000 Power Module ............................................................................ 41 2 Preparation for Installation .................................................................................................................... 42 2.1 Safety Suggestions .................................................................................................................... 42 2.1.1 Safety Precautions for Installing the System ................................................................. 42 2.1.2 Safety Precautions for Removal .................................................................................... 42 2.1.3 Electrical Safety ............................................................................................................. 44 2.1.4 Static Discharge Damage Prevention ............................................................................ 44 2.1.5 Laser Safety ................................................................................................................... 45 2.2 Installation Site Requirements .................................................................................................... 45 2.2.1 Rack Mounting Requirements ....................................................................................... 45 2.2.2 Ventilation Requirements ............................................................................................... 45 2.2.3 Temperature and Humidity Requirements ..................................................................... 47 2.2.4 Cleanness Requirements .............................................................................................. 48 2.2.5 Power Requirements ..................................................................................................... 48 2.3 System Grounding Requirements .............................................................................................. 49 2.3.1 Safety Ground ................................................................................................................ 49 2.3.2 Lightning Ground ........................................................................................................... 49 2.3.3 EMC Ground .................................................................................................................. 49 2.3.4 EMI Consideration ......................................................................................................... 50 2.3.5 Precaution for Fiber Connection .................................................................................... 50 2.4 Installation Tool Requirements ................................................................................................... 50 2.5 Unpacking Requirements ........................................................................................................... 51 2.5.1 Goods Checklist ............................................................................................................. 51 3 Switch Installation ................................................................................................................................. 52 3.1 Installation Flow .......................................................................................................................... 53 3.2 Installation Verification ................................................................................................................ 54 3.3 Cabinet Installation ..................................................................................................................... 54 3.1.1 Precautions .................................................................................................................... 54 3.1.2 Simple Installation Steps ................................................................................................ 54 3.2 Mounting into the Cabinet .......................................................................................................... 55 3.2.1 Precautions .................................................................................................................... 55 3.2.2 Simple Installation Steps ................................................................................................ 55 3.3 Installing Fan Tray ...................................................................................................................... 55 3.4 Installing Power Supply .............................................................................................................. 57 3.5 Installing Handle ......................................................................................................................... 61 3.6 Installing Cabling Rack for RG-S8610........................................................................................ 63 3.7 Installing Air Filter for RG-S8614/S8610 .................................................................................... 65 3.8 Grounding ................................................................................................................................... 66 3.8.1 Precautions .................................................................................................................... 66 3.8.2 Simple Grounding Steps ................................................................................................ 66 3.9 Connecting the DC Power Supply to the Power Module ........................................................... 66 3.9.1 Precautions .................................................................................................................... 66 3.9.2 Simple Connection Steps............................................................................................... 67 3.10 Connecting the AC Power Supply to the Power Module ............................................................ 67 3.10.1 Precautions .................................................................................................................... 67 3.10.2 Simple Connection Steps............................................................................................... 68 3.11 Connecting the Cables of the Management Module .................................................................. 68 3.11.1 Simple Connection Steps............................................................................................... 68 3.12 Removing Boards from RG-S8614/S8610/S8606 ...................................................................... 68
3 3
3.12.1 Precautions .................................................................................................................... 68 3.12.2 Steps for Removing Boards ........................................................................................... 68 3.13 Installing Boards on RG-S8614/S8610/S8606 ........................................................................... 70 3.13.1 Precautions .................................................................................................................... 70 3.13.2 Simple Steps of Board Installation ................................................................................. 70 3.13.3 Precautions of Installing M8600-FW and RG-WALL 1600 FW Module ......................... 70 3.14 Connecting the External Interface Cables .................................................................................. 71 3.14.1 Precautions .................................................................................................................... 71 3.14.2 Simple Connection Steps............................................................................................... 71 3.15 Binding the Cables ..................................................................................................................... 71 3.15.1 Precautions .................................................................................................................... 71 3.15.2 Simple Binding Steps ..................................................................................................... 72 3.16 Installation Verification ................................................................................................................ 72 3.16.1 Verifying the Cabinet ...................................................................................................... 72 3.16.2 Verifying the Cables ....................................................................................................... 72 3.16.3 Verifying the Power Supply ............................................................................................ 72 3.17 Upgrade Instruction for MEM-CM-512 Memory Bank ................................................................ 72 3.17.1 Precautions .................................................................................................................... 72 3.17.2 Specification ................................................................................................................... 72 3.17.3 Installation Instruction .................................................................................................... 73 3.17.4 Installation Verification ................................................................................................... 74 4 Maintenance ......................................................................................................................................... 75 4.1 RG-S8614/S8610/S8606 Monitoring .......................................................................................... 75 4.2 RG-S8614/S8610/S8606 Hardware Maintenance ..................................................................... 75 4.2.1 Board Maintenance ........................................................................................................ 75 4.2.2 Ventilation System Maintenance ................................................................................... 75 4.2.3 Power Supply Maintenance ........................................................................................... 76 4.3 Replacing LCD ........................................................................................................................... 76 4.4 Remote Maintenance ................................................................................................................. 76 5 Troubleshooting .................................................................................................................................... 77 5.1 General Installation Troubleshooting Flow ................................................................................. 77 5.2 Common Troubleshooting Procedures ....................................................................................... 78 AppendixA Connectors and Connection Media ......................................................................................... 81 1.1000BASE-T/100BASE-TX/10BASE-T Port ..................................................................................... 81 2. Fiber Connection .............................................................................................................................. 82 AppendixB Mini-GBIC and 10G XFP Modules ............................................................................................. i 1. Models and Technical Specifications of the Mini-GBIC (SFP) Module ................................................ i 2. Models and Technical Specifications of the 10G XFP Module ........................................................... iv RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 1
Product Overview 1.1 Product Overview As the Internet users grow at an explosive rate in recent years, they are no longer satisfied with existing communication ways that rely largely on telephone networks, and demand telecom operators to provide multimedia services such as video, audio and data. The traditional narrowband access method can no longer meet the needs for telecom services, while the broadband access technology will bring about tremendous changes to the life and working style of people. Compared with broadband access methods such as ADSL and HFC, the Ethernet access method features such advantages as high bandwidth and low cost.The Ethernet is the most direct way to bear IP service, the primary service of the broadband metropolitan area network (MAN). Users do not need to add any other special equipment in their network, reducing the cost in protocol conversion. In addition, the Ethernet access method is ideal for the users densely populated in residential areas. It accommodates the trend where fibers are used for the access network. Consequently, the Ethernet gains rapid development and wide application in the broadband access field. In this situation, Ruijie Network is concentrated on the introduction of the high-density multi-service IPv6 core router switch RG-S8600 after the release of the multi-service 10G core router switch RG-S8600E that applies to the backbone Ethernet. RG-S8600, the next generation of multi-service IPv6 10G core router switch, provides powerful defense ability on the basis of high performance and high capacity. Moreover, it boasts the ability to add and expand services according to your requirements, and thus satisfying the design requirements while putting equal emphasis on service and performance. Three kinds of switches are available: RG-S8614 configured with 14 horizontal slots, RG-S8610 configured with 10 vertical slots and RG-S8606 configured with 6 horizontal slots. RG-S8600 series series provides users with high-speed non-blocking data switching. With powerful switching and routing functions and secure intelligent technologies, it offers an end-to-end solution in conjunction with various series of Ruijie switches. RG-S8600 series is ideal for large-scale core backbone networks and node switches with heavy traffic. By extending high performance multi-service cards to support such functions as IPv6, RG-S8600 series can accommodate the flexible yet complicated application requirements of customer environments. Applications: n Core layers of such enterprise networks as educational, financial and governmental organizations n Operation environments that need powerful routing function and carrier-class security & reliability n Multi-layer switching of enterprise networks with high bandwidth and 10G needs n Enterprise environments that need to provide high QoS assurance for various applications Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 2
1.2 Technical Specifications 1.2.1 Product Features n Powerful expandability RG-S8600 supports functions like policy-based routing and IPv6. It provides faster and high effective processing ability by expanding high-performance multi-service cards. n Hot-swappability With a modular design, all the switching modules, management modules, power supply, and fan tray are hot swappable, allowing you to replace modules without powering down the system. n Redundancy configuration RG-S8600 series provides system redundancy configuration, particularly dual redundancy for its power supply and management module. This greatly enhances system reliability and stability. n Powerful data processing design Complicated functions of RG-S8600 series such as switching, routing, ACL, and QoS are enabled based on hardware to relieve the influence of enabling these functions based on software on high-speed data processing. The management module performs such functions as route management, network management, and network service. The user interface module can independently implement such functions as hardware routing, switching and multicast. On the other hand, the user switching port independently implements hardware-based ACL and QoS. All these greatly enhance the processing capability of the equipment as a whole. n High security guarantee 1) Physical security: RG-S8600 series provides physical security guarantee such as redundant management modules, redundant power modules. Each module is hot-swappable. 2) Antivirus and attack defense: As the virus and attacks over the Internet is increasingly growing, RG-S8600 series provides robust antivirus and attack defense functions, like ACL and Source IP Spoofing, among many others. RG-S8600 series provides the multiple-port synchronous monitoring technology that supports flexible network monitoring and enhances monitoring capability. 3) Equipment management security: To prevent non-administrators from logging in and manipulating the network equipment that may affect network transmission and security, RG-S8600 series provides SSH encrypted login and source IP address restriction for telnet/web login. 4) Access security: Hardware-based IP address, MAC address and port binding can enhance access control. 802.1x can meet 6-element binding access restriction. IGMP source port check can control invalid multicast sources and improve network security. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 3
PVLAN (port protection) can isolate the information exchanged between users without occupying VLAN resources. The port MAC address lock and port MAC address access quantity restriction can bar the access from illegal hosts. n A full range of application support techniques (QoS, multicast) RG-S8600 series provides multiple traffic classifications and QoS techniques to guarantee the bandwidth necessary for various applications. RG-S8600 series provides multiple multicast support techniques including IGMP snooping, IGMP, PIM(SM/DM)to ensure reasonable bandwidth usage in case of multicast service in a network. n Supporting L2 VPN (VPLS) RG-S8600 series supports Service Provider VLAN (Double Tagging, VLAN tunnel) that enables secondary VLAN identification for switched data. The outer layer IDs are used to create VPNs and provide link selection, while the inner layer IDs are used to identify the service VLAN information and implement L2 VPNs in the Ethernet environment, which offers data transmission security control in the traditional Ethernet environment. n ECMP/WCMP (Equal-Cost Multipath Routing/ Weight-Cost Multipath Routing) When there are multiple links to the same destination in a network, with traditional routing technologies, packets travel through only one link of them to the destination while other links being in standby or inactive status. Moreover, inter-link switch takes some time in the dynamic routing environment. On the other hand, the ECMP and WCMP can use multiple links at the same time in such a network environment. This not only increases the transmission bandwidth, but also backs up the data transmitted through the failed link without delay and packet loss. n Supporting sophisticated dual-core technology RG-S8600 series supports multiple STPs and VRRPs including 802.1D, 802.1W, and 802.1S, offering sophisticated dual-core guarantee technologies. n Providing visual status display RG-S8600 series is embedded with an LCD screen, used for providing current system information such as working time and system utilization. n Supporting advanced 10G Ethernet technology RG-S8600 series provides mainstream 10G LAN transmission standards at present such as 10GBASE-R and 10GBASE-W. n Supporting PoE technology RG-S8600 series provides linecards supporting PoE. PoE design completely conforms to the requirements of the IEEE 802.3af standards. n High-density port design The RG-S8614 provides up to 576 Gigabit Ethernet ports, 288 Gigabit fiber ports or 96 10G ports, RG-S8610 provides up to 384 Gigabit Ethernet ports, 192 Gigabit fiber ports or 64 10G ports and RG-S8606 provides up to 192 Gigabit Ethernet ports, 96 Gigabit fiber ports or 32 10G ports, offering flexible network expansion for large enterprise parks. Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 4
Power supply RG-PA1200: 90VAC to 264VAC, 47Hz to 63Hz; power: 1200W RG-PA1200E: 90VAC to 264VAC, 47Hz to 63Hz; power: 1200W RG-PA2000: 90VAC to 176VAC, 47Hz to 63Hz; power: 1200W 176VAC to 264VAC, 47Hz to 63Hz; power: 2000W RG-PD1200: -36Vdc to -72Vdc; power:1200W RG-PD2000: -36Vdc to -72Vdc; power:2000W
Note: PA refers to the AC power while PD refers to the DC power Power supply redundancy Supported(must be the same type, for example, all ACs or DCs) Fan M8614-Fan (supporting hot swappability and fault alarming) M8610-Fan (supporting hot swappability and fault alarming) M8606-Fan (supporting hot swappability and fault alarming) Environment EMC GB9254-1998, FCC Class A Safety regulation GB4943-2001
Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Earthquake-r esistance Able to resist the Earthquake intensity 9 Weight !114kg !93kg !73kg Dimension 436.8x508x932.2 mm (L x W x H) 436.8 x 448 x956 mm (L x W x H) 436.8x508x647.4 mm (L x W x H) Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 6
1.3 Product Appearance 1.3.1 Appearance of RG-S8614 Figure 1-1 Appearance of RG-S8614
1. Modular layer: Offers 14 module slots at most; 2. Power layer: Supports up to two AC or DC power supplies; 3. Air outlet: Locates in the back of the chassis, the main heat dissipation unit of the system. (3) (1) (2) RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 7
1.3.2 Appearance of RG-S8610 Figure 1-2 Appearance of RG-S8610
1. Air outlet layer: Discharges air on three sides; 2. Fan tray: Houses fan, the main heat dissipation unit of the system; 3. Modular layer: Offers 10 vertical module slots that house different functional modules; 4. Wiring layer: Arranges and leads out various cables in good order while preventing the drooping cables from blocking the air inlet; 5. Air inlet layer: Inducts air into the chassis; 6. Power layer: Supports up to two AC or DC power supplies. 1.3.3 Appearance of RG-S8606 Figure 1-3 Appearance of RG-S8606 (1) (2) (3) (4) (5) (6) Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 8
1. Modular layer: Offers 6 module slots at most; 2. Power layer: Supports up to two AC or DC power supplies; 3. Air outlet: Locates in the back of the chassis, the main heat dissipation unit of the system. 1.4 RG-S8614/S8610/S8606 Hardware Components RG-S8614$s hardware system consists of chassis, power system, system modules, fan tray and air filter. RG-S8610$s hardware system consists of chassis, power system, system modules, cabling rack, fan tray, air inlet/outlet ducts and air filter. RG-S8606$s hardware system consists of chassis, power system, system modules and fan tray. (3) (1) (2) RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 9
1.4.1 Chassis 1.4.1.1 RG-S8614s chassis RG-S8614 uses a standards-based 19-inch chassis with 932.2mm high, 436.8mm wide, and 508 mm deep. It consists of system module layer, fan layer, air filter, and power system layer. The system module layer is a module plug-in frame that mechanically supports various modules of RG-S8614. At the bottom of the chassis are two power frames. The air filter is located on the right of the module plug-in frame of the chassis. On the back of the module plug-in frame is the fan layer, which houses ten fans. 1.4.1.2 RG-S8610s chassis RG-S8610 uses a standards-based 19-inch chassis with 956mm high, 436.8mm wide, and 448 mm deep. It consists of system module layer, fan layer, air inlet/outlet layer, cabling rack, air filter, and power layer. The system module layer is a module plug-in frame that mechanically supports various modules of RG-S8610. At the bottom of the chassis are two power frames, above which is the air inlet layer. The air filter is located between the air inlet layer and the cabling rack, which is located below the system module layer. Above the system module layer is the fan layer, which houses six fans. At the top of the chassis is the air outlet layer working in duced draught mode 1.4.1.3 RG-S8606s chassis The RG-S8606 uses a standards-based 19-inch chassis with 674.4mm high, 436.8mm wide, and 508 mm deep. It consists of system module layer, fan layer, air inlet/outlet layer, cabling rack, air filter, and power layer. The system module layer is a module plug-in frame that mechanically supports various modules of RG-S8606. At the bottom of the chassis are two power frames. At the backof the module plug-in frame is the fan layer, which houses six fans. 1.4.2 Module Plug-in Frame RG-S8614/ S8610/ S8606$s module frame consists of module slots and backplane. RG-S8614 offers 14 module slots, of which the two in the middle are for CMs only. The six slots on the top and bottom can accommodate a mix of various modules. Modules are inserted horizontally, with the same height of 412 mm, depth of 350 mm. The backplane enables the interconnection of high-speed data links between CMs and linecards and that of various management and control signals. RG-S8610 offers 10 module slots, of which the two in the middle are for CMs only. The eight slots on both sides can accommodate a mix of various modules. Modules are inserted vertically, with the same height of 412 mm, depth of 350 mm. The backplane enables the interconnection of high-speed data links between CMs and linecards and that of various management and control signals. RG-S8606 offers 6 module slots, of which the two in the middle are for CMs only. The four slots on the top and bottom can accommodate a mix of various modules. Modules are inserted horizontally, with the same height of 412 mm, depth of 350 mm. The backplane Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 10
enables the interconnection of high-speed data links between CMs and linecards and that of various management and control signals. 1. Backplane function n Interconnect various signals between modules and provide high-speed communications channels n Passive backplane n Support active/standby switching between CMs n Support automatic identification of various slots n Implement distributed power supply n Introduce monitoring signal lines of the fan and power supply 2. Slot number In full configuration, modules in the module plug-in frame of RG-S8614 are configured as below: n Two CMs serving as mutual backup n Twelve modules used to meet specific needs The slots for the two CMs are in the middle and be identified as M1 and M2 from up down. The other twelve linecards are numbered as 1-12 from down up. In full configuration, modules in the module plug-in frame of RG-S8610 are configured as below: n Two CMs serving as mutual backup n Eight modules used to meet specific needs The slots for the two CMs are in the middle and be identified as M1 and M2 from left to right. The other eight linecards are numbered as 1-8 from left to right. In full configuration, modules in the module plug-in frame of RG-S8606 are configured as below: n Two CMs serving as mutual backup n Four modules used to meet specific needs The slots for the two CMs are in the middle and be identified as M1 and M2 from left to right. The other four linecards are numbered as 1-4 from left to right. 1.5 Ventilation/Heat Dissipation System The operating temperature of RG-S8614/S8610/S8606 is 0 to 40#C. The thermal design must ensure that the surface temperature of the components does not exceed 50% to 80% of the maximum allowed temperature at such an ambient temperature for high reliability, security, and reparability. According to the thermal design of RG-S8614/S8610/S8606, fans are used to induct air for a forced convection in order to ensure that the equipment works in the specified environment well. Figure 1-4, Figure 1-5 and Figure 1-6 show the ventilation/heat dissipation system of RG-S8614/S8610/S8606, respectively. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 11
Figure 1-4 RG-S8614 Ventilation/heat dissipation system
Note: This structure is designed with air inlet on two sides, and air outlet at back. 10PCS 120*120*38 fans are used to blow air outside for convection and ultimately heat dissipation. Therefore, the chassis should be mounted at a place with sufficient space for air circulation. Figure 1-5 RG-S8610 Ventilation/heat dissipation system
Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 12
Note: This structure is designed with air inlet at front/back and two sides, and air outlet at top back and both sides. 6PCS 120*120*38 fans are used to blow air outside for convection and ultimately heat dissipation. Therefore, the chassis should be mounted at a place with sufficient space for air circulation.
Figure 1-6 RG-S8606 Ventilation/heat dissipation system
Note: This structure is designed with air inlet at front and air outlet at back. 6PCS 120*120*38 fans are used to blow air outside for convection and ultimately heat dissipation. Therefore, the chassis should be mounted at a place with sufficient space for air circulation. 1.6 Modules RG-S8614/S8610/S8606 supports the modules described in Table 1-1. M8610/M8606-CM: As the switching and central control module for RG-S8610/S8606, the M8610/M8606-CM module manages the entire system, including L2/L3 protocol processing, route management, user access control and management, and network and operation maintenance. M8614/M8610/M8606-CMII: As the switching and central control module for RG-S8614/S8610/S8606, it enhances the processing capability of the processor on the basis of the M8610/M8606-CM. The M8614/M8610/M8606-CMII module manages the entire system, including L2/L3 protocol processing, route management, user access control and management, and network and operation maintenance. M8600-24SFP/12GT: It provides 12 1000BASE-X SFP ports and 12 1000M fiber/copper combo ports and supports up to 24 1000BASE-X SFP ports, or 12+M 1000BASE-X SFP ports and N 10/100/1000BASE-T ports where M plus N equals to 12. It features layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, and 1550nm long-distance SFP and SFP copper port. M8600-24GT/12SFP: It provides 12 10/100/1000BASE-T 1000M copper ports and 12 1000M fiber/copper combo ports, and supports up to 24 10/100/1000BASE-T ports, or 12+M 10/100/1000BASE-T ports and N 1000BASE-X ports where M plus N equals 12. It features layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, and 1550nm long-distance SFP and SFP copper port. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 13
M8600-02XFP: It provides 2 10,000M XFP ports. It features layer-2/3 switching and routing, and supports 850nm multi-mode XFP, 1310nm single-mode XFP, and 1550nm single-mode XFP. M8600P-24GT/12SFP: It provides 12 10/100/1000BASE-T 1000M copper ports and 12 1000M fiber/copper combo ports, and supports up to 24 10/100/1000BASE-T ports, or 12+M 10/100/1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 12. The 24 10/100/1000BASE-T 1000M copper ports support IEEE 802.3af and are considered to be PoE ports by default to conenct PoE devices directly. It features layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, and 1550nm long-distance SFP and SFP copper port. M8600-48GT/4SFP: It provides 44 10/100/1000BASE-T 1000M copper ports and 4 1000M fiber/copper combo ports, and supports up to 48 10/100/1000BASE-T ports, or 44+M 10/100/1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 4. It features the functions of layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, and 1550nm long-distance SFP and SFP copper port. M8600P-48GT/4SFP: It provides 44 10/100/1000BASE-T 1000M copper ports and 4 1000M fiber/copper combo ports, and supports up to 48 10/100/1000BASE-T ports, or 44+M 10/100/1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 4. The 48 10/100/1000BASE-T 1000M copper ports support IEEE 802.3af and are considered to be PoE ports by default to conenct PoE devices directly.It features layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, and 1550nm long-distance SFP and SFP copper port. M8600-04XFP: It provides 4 10,000M XFP ports. It features layer-2/3 switching and routing, and supports 850nm multi-mode XFP, 1310nm single-mode XFP and 1550nm single-mode XFP. M8600-24SFP: It provides 24 SFP ports that support 1000BASE-X and 100BASE-X modes. It features layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, and 1550nm long-distance SFP and SPF copper port. M8600-NMM: It is an agent card that supports network flow control. The linecard does not provide any external port for improving the NMM function. M8600-MPLS: It is an agent card that supports MPLS. The linecard does not provide any external port for improving the MPLS function. M8600-08XFP: It provides 8 10,000M XFP ports. It features layer-2/3 switching and routing, and supports 850nm multi-mode XFP, 1310nm single-mode XFP and 1550nm single-mode XFP. M8600-02XFP24SFP/12GT-E: It provides 2 10,000M XFP ports, 12 1000M SFP ports and 12 1000M fiber/copper combo ports, and supports up to 2 XFP ports and 24 1000BASE-X ports, or 2 XFP ports, 12+M 1000BASE-X ports and N 1000BASE-X ports where M plus N equals to 12. It features layer-2/3 switching and routing, and supports 850nm multi-mode SFP, 1310nm single-mode SFP, 1550nm long-distance SFP, SPF copper port, and 850nm multi-mode XFP, 1310nm single-mode XFP, 1550nm single-mode XFP. M8600-VSU-02XFP: It supports VSU and provides 2 10,000M XFP ports. It features layer-2/3 linespeed switching and routing and supports 850nm multi-mode XFP, 1310nm single-mode XFP and 1550-nm single-mode XFP. M8600-FW: It is a service card that supports firewall. The linecard provides one console port and MGMT port for improving the firewall function. RG-WALL 1600 FW Module: It is a service card that supports firewall. The linecard provides one console port and MGMT port for improving the firewall function. M8614-Fan: As the fan tray of the system, it provides ten 120*120*38 fans to guarantee heat dissipation of the system. Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 14
M8610/M8606-Fan: As the fan tray of the system, it provides six 120*120*38 fans to guarantee heat dissipation of the system. RG-PA1200/1200E/PA2000: As the AC power module of the system, it provides the input interface for 220V AC power supply. RG-PD1200/PD2000: As the DC power module of the system, it provides the input interface for -48V DC power supply. 1.6.1 M8610/M8606-CM Figure 1-7 shows the basic appearance of M8610-CM, the primary CM of RG-S8610. Fiugre 1-8 shows the basic appearance of M8606-CM, the primary CM of RG-S8606. M8610/M8606-CM performs such functions as system switching, system status control, route management, access control, and network maintenance. Inserted in slots M1 and M2 on the back plane of the chassis, the CM supports active/standby redundancy, hot backup and hot swappability. Note: In the system, there must be at least one M8610-CM/M8606-CM for the system to work normally. However, you are recommended to configure this module for both slots for higher reliability. Figure 1-7 Basic Appearance of the M8610-CM
Figure 1-8 Basic Appearance of the M8606-CM
1. Interface The M8610/M8606-CM module provides three interfaces: n USB interface: By connecting the USB interface, USB storage devices can keep logs, host version, alarms and other diagnosis information, and thus facilitating online upgrade and log maintenance. Note: To secure data and prevent damage to the device, it is recommended to use qualified USB flash disk. The USB interface of RG-S8600 is compatible with most USB controllers. Some types of USB flash disk may not be recognized. You are recommended to use Patriot and Start-net Digital USB flash disk. n Console port: As the serial communications port, it uses RS-232 interface level and standard RJ45 connector. This port is used to connect the serial port of terminals running on the background for such tasks as system debugging, configuration, maintenance, management, and host software loading. n 10/100M MGMT port: As the 10/100BASE-T Ethernet port, it uses RJ-45 connector. This port can be used to connect the Ethernet port of the background computer for loading programs. When it is connected to the Ethernet port of the background computer, the standard network cable is necessary. 2. LEDs The M8610/M8606-CM module provides various system LEDs, as described in the following table: RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 15
Table 1-2LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: The module is faulty. Flashing green: The module is initializing; if it keeps on flashing, the module is faulty. Solid green: The module has finished initialization and can perform switching normally. Primary Primary/standby management module LED OFF: The current module is the standby management module. Green: The current module is the active management module. Alarm Fault alarm OFF: Free from fault Red: System fault 10/100M MGMT Port LED LED1 (Full duplex) OFF: Work in the half duplex mode. Yellow: Work in the full duplex mode. LED2 ( Link/ACT) OFF: Port is not linked. Green: Port is linked. Flashing green: The data is transmitted on the port. 3. Technical Specifications Table 1-3Technical specifications of M8610/M8606-CM Product Model M8610-CM M8606-CM Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q Management mode CLI, Telnet and Web-based Port type One 10/100M Ethernet port as the management port One standard RJ45 serial port LED Status, Primary, Alarm and 10/100M MGMT port LED Hot swappability Supported Management redundancy Supported Power consumption <30W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346%30 mm ( Lx W x H) 436*346%30 mm ( Lx W x H) Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 16
1.6.2 M8614/M8610/M8606-CMII Figure 1-9 shows the basic appearance of M8614-CMII, the primary CM of RG-S8614.Figure 1-10 shows the basic appearance of M8610-CMII, the primary CM of RG-S8610. Fiugre 1-11 shows the basic appearance of M8606-CMII, the primary CM of RG-S8606. The M8614/M8610/M8606 performs such functions as system switching, system status control, route management, access control, and network maintenance. Inserted in slots M1 and M2 on the backplane of the chassis, the CM supports active/standby redundancy for hot backup and also hot swappability. Note: In the system, there must be at least one M8614/M8610/M8606-CMII for the system to work normally. However, you are recommended to configure this module for both slots for higher reliability. Figure 1-9 Basic Appearance of tM8614-CMII
Figure 1-10 Basic Appearance of M8610-CMII
Figure 1-11 Basic Appearance of M8606-CMII
1. Interface The M8614/M8610/M8606-CMII module provides three interfaces: n USB interface: By connecting the USB interface, USB storage devices can keep logs, host version, alarms and other diagnosis information, and thus facilitating online upgrade and log maintenance. Note: To secure data and prevent damage to the device, it is recommended to use qualified USB flash disk. The USB interface of RG-S8600 is compatible with most USB controllers. Some types of USB flash disk may not be recognized. You are recommended to use Patriot and Start-net Digital USB flash disk. n Console port: As the serial communication port, it uses RS-232 interface level and standard RJ45 connector. This port is used to connect the serial port of terminals running on the background for such tasks as system debug, configuration, maintenance, management, and host software loading. n 10/100M MGMT port: As the 10/100BASE-T Ethernet port, it uses the RJ-45 connector. This port can be used to connect the Ethernet port of the background computer for loading programs. When it is connected to the Ethernet port of the background computer, the standard network cable is necessary. 2. LEDs The M8614/M8610/M8606-CMII module provides various system LEDs, as described in the following table: RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 17
Table 1-4LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: The module is faulty. Flashing green: The module is initializing; if it keeps on flashing, the module is faulty. Solid green: The module has finished initialization and can perform switching normally. Primary Primary/standby management module LED OFF: The current module is the standby management module. Green: The current module is the active management module. Alarm Fault alarm OFF: Free from fault Red: System fault 10/100M MGMT Port LED LED1 (Full duplex) OFF: Work in the half duplex mode. Yellow: Work in the full duplex mode. LED2 ( Link/ACT) OFF: Port is not linked. Green: Port is linked. Flashing green: The data is transmitted on the port. 3. Technical Specifications Table 1-5Technical Specifications of M8614/M8610/M8606-CMII Product Model M8610-CMII M8610-CMII M8606-CMII Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q Management mode CLI, Telnet and Web-based Port type One 10/100M Ethernet port as the management port One standard RJ45 serial port LED Status, Primary, Alarm and 10/100M MGMT port LED Hot swappability Supported Management redundancy Supported Power consumption <110W <50W <50W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 18
Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 3.5 Kg Net weight: 2.8 Kg Dimensions 436*346%30 mm ( Lx W x H) 436*346%30 mm ( Lx W x H) 436*346%30 mm ( Lx W x H) 1.6.3 M8600-24SFP/12GT Figure 1-12 shows the basic appearance of M8600-24SFP/12GT, the line card of RG-S8614/S8610/S8606. M8600-24SFP/12GT provides 12 1000M SFP ports and 12 1000M fiber/copper combo ports, and supports up to 24 1000BASE-X ports or 12+M 1000BASE-X ports and N 1000BASE-T ports where M plus N equals to 12. It features layer-2/3 switching. The M8600-24SFP/12GT module is hot swappable. Figure 1-12 Basic appearance of the M8600-24SFP
1. Interface M8600-24SFP/12GT provides 12 1000M SFP ports and 12 1000M fiber/copper combo ports. It features layer-2/3 switching with the 1000M wire speed. When the function of automatic negotiation is enabled, the 1000M copper port supports automatic MDI/MDI-X identification. The SFP ports support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M SFP fiber/copper combo port. The module is hot swappable. Note: The M8600-24SFP/12GT module provides 12 10/100/1000BASE-T SFP fiber ports. In other words, each SFP port corresponds to one 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when auto negotiation is enabled. 2. LEDs The M8600-24SFP/12GT module provides various system LEDs, as described in the following table: Table 1-6LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 19
Sign Description Detailed Information Module Fiber module existence LED OFF: The fiber module is not available. Green: The fiber module is available. Link/ACT Port status LED OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port. 3. Technical Specifications Table 1-7Technical specifications of the M8600-24SFP/12GT Product Model M8600-24SFP/12GT Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type 12 SFP 1000M ports and 12 1000M fiber/copper combo ports (supporting 1000BASE-SX/LX,1000BASE-TX, 1000BASE-LH and 10/100/1000BASE-TX) Transmission media 10/100/1000BASE-TX: 100m (Category-5 or above unshield pair twists or pair twists) For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT LEDs Hot swappability Supported Power consumption <75W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.4 M8600-24GT/12SFP Figure 1-13 shows the basic appearance of M8600-24GT/12SFP, the line card of RG-S8614/S8610/S8606. The M8600-24GT/12SFP moduleprovides 12 10/100/1000BASE-T copper ports and 12 fiber/copper combo 1000M ports. It features layer-2/3 switching. The M8600-24GT/12SFP module is hot swappable. Figure 1-13 Basic Appearance of M8600-24GT/12SFP Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 20
1. Interface M8600-24GT/12SFP provides 12 10/100/1000BASE-T copper ports and 12 fiber/copper combo 1000M ports, and supports up to 24 1000BASE-T ports or 12+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 12. When the function of automatic negotiation is enabled, the 1000M copper port supports automatic MDI/MDI-X identification. The SFP ports support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M SFP fiber/copper combo ports. Note: The M8600-24GT/12SFP module provides 12 10/100/1000BASE-T SFP fiber ports. In other words, each SFP port corresponds to one 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when auto negotiation is enabled. 2. LEDs The M8600-24GT/12SFP module provides various system LEDs, as described in the following table: Table 1-8 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: It has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/ACT Port status LED Copper Port: OFF: Port is not linked. Green: Port is linked at 1000M. Orange: Port is linked at 10/100M. Flashing: Data is transmitted on the port. Fiber Port: OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port. 3. Technical Specifications Table 1-9 Technical specification of M8600-24GT/12SFP Product Model M8600-24GT/12SFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type 12 10/100/1000BASE-T copper ports and 12 fiber/copper combo 1000M ports; Up to 24 1000BASE-T ports or 12+M 1000BASE-T ports and N 1000BASE-X ports, where M plus N equals to 12. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 21
Product Model M8600-24GT/12SFP Transmission media 10/100/1000BASE-TX: 100m (Category-5 or above unshield pair twists or pair twists) For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT Hot swappability Supported Power consumption <85W+15.4xN (N indicates the used PoE ports in the range of 1 to 24) EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% - 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346*45 mm ( L x W x H) 1.6.5 M8600-02XFP Figure 1-14 shows the basic appearance of M8600-02XFP, the line card of RG-S8614/S8610/S8606. M8600-02XFP provides two 10,000M XFP ports and features layer-2/3 switching. The M8600-02XFP is hot swappable. Figure 1-14 Basic Appearance of M8600-02XFP
1. Interface M8600-02XFP provides two 10,000M XFP ports and features layer-2/3 switching at the 10,000M wire speed. The XFP ports support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 10,000M XFP fiber modules, thus facilitating configuration for users. 2. LEDs The M8600-02XFP module provides various system LEDs, as described in the following table: Table 1-10 LEDs on the front panel Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 22
Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/ACT Port status LED OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port. 3. Technical Specifications Table 1-11 Technical specifications of M8600-02XFP Product Model M8600P-02XFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE802.3ae, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type Two 10,000M XFP ports Transmission media For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT Hot swappability Supported Power consumption <75W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346*45 mm ( L x W x H) 1.6.6 M8600P-24GT/12SFP Figure 1-15 shows the basic appearance of M8600P-24GT/12SFP, the line card of RG-S8614/S8610/S8606. M8600P-24GT/12SFP provides 12 10/100/1000BASE-T 1000M copper ports and 12 1000M fiber/copper combo ports, and supports up to 24 1000BASE-T ports or 12+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 12. It features layer-2/3 switching and supports hot plug-in. The M8600P-24GT/12SFP is hot swappable. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 23
Figure 1-15 Basic appearance of M8600P-24GT/12SFP
1. Interface M8600P-24GT/12SFP provides 12 10/100/1000BASE-T 1000M copper ports and 12 1000M fiber/copper combo ports, and supports up to 24 1000BASE-T ports or 12+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 12. The 1000M copper port supports PoE by default. automatic MDI/MDI-X identification is available only when automatic negotiation is enabled. The SFP ports support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M SFP fiber modules and SFP copper ports, thus facilitating configuration for users. Note: The M8600P-24GT/12SFP module provides 12 10/100/1000BASE-T SFP fiber ports. In other words, each SFP port corresponds to one 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when auto negotiation is enabled.
Warning M8600P-24GT/12SFP does not support the hot pull-out operation. You need to perform the following operations to achieve it: 1. Disconnect all the cables connected to the linecard; 2. Hold the Mode button for over three seconds until all LEDs on the linecard go off; 3. Configure the pull-out operation through software commands. (For relevant software configuration commands, refer to the corresponding software description.) 2. LEDs The M8600P-24GT/12SFP module provides various system LEDs, as described in the following table: Table 1-12 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Mode LED status indication Green: Data exchange indication Orange: PoE status indication Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 24
Sign Description Detailed Information Link/AC T Port status LED Copper Port: When Mode is green (in switch mode): OFF: Port is not linked. Green: Port is linked at 1000M. Orange: Port is linked at 10/100M. Flashing green: Data is transmitted on the port. When Mode is orange (in PoE mode): Off: The PoE device does not work normally. Green: The PoE device works normally. Orange: The PoE device is overloaded. Red: PoE failure Fiber Port: OFF: Port is not linked. Green: Port is linked Flashing green: Data is transmitted on the port. 3. Technical Specifications Table 1-13 Technical specifications of M8600P-24GT/12SFP Product Model M8600P-24GT/12SFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.3af, IEEE 802.1D and IEEE 802.1Q 802.1X authentication Port type 12 10/100/1000BASE-T copper ports and 12 fiber/copper combo 1000M ports; Up to 24 1000BASE-T ports, or 12+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 12. Up to 24 PoE ports. Transmission media 10/100/1000BASE-TX: 100m (Category-5 or above unshield pair twists or pair twists) For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT Hot swappability Supported Power consumption <85W+15.4xN (N indicates the PoE port being used, of which the value is less than 24.) EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 25
Product Model M8600P-24GT/12SFP Weight Net weight: 2.8 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.7 M8600-48GT/4SFP Figure 1-16 shows the basic appearance of M8600-48GT/4SFP, the line card of the RG-S8614/S8610/S8606. The M8600-48GT/4SFP module provides 44 10/100/1000BASE-T copper 1000M ports and 4 fiber/copper combo 1000M ports. The M8600-48GT/4SFP module is hot swappable. Figure 1-16 Basic appearance of M8600-48GT/4SFP
1. Interface M8600-48GT/4SFP provides 44 10/100/1000BASE-T copper ports and 4 fiber/copper combo 1000M ports, and supports up to 48 1000BASE-T ports or 44+M 1000BASE-T ports and N 1000BASE-X ports, where M plus N equals to 4. When the function of automatic negotiation is enabled, the 1000M copper port supports automatic MDI/MDI-X identification. The SFP ports support short-wave (850nm, multi-mode) and long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M SFP fiber modules and SFP copper ports, thus facilitating configuration for users. Note: The M8600-48GT/4SFP module provides four 10/100/1000BASE-T SFP fiber ports. In other words, each SFP port corresponds to one 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when auto negotiation is enabled. 2. LEDs The M8600-48GT/4SFP module provides various system LEDs, as described in the following table: Table 1-14 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/A CT Port status LED Copper Port: OFF: Port is not linked. Green: Port is linked at 1000M. Orange: Port is linked at 10.100M. Flashing: Data is transmitted on the port. Fiber Port: OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port. Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 26
3. Technical Specifications Table 1-15 Technical specifications of M8600-48GT/4SFP Product Model M8600-48GT/4SFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type 44 10/100/1000BASE-T copper ports and 4 fiber/copper combo 1000M ports; Up to 48 1000BASE-T ports or 44+M 1000BASE-T ports and N 1000BASE-X ports, where M plus N equals to 4. Transmission media 10/100/1000BASE-TX: 100m (Category-5 or above unshield pair twists or pair twists) For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT Hot swappability Supported Power consumption <100W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 3.5 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.8 M8600-04XFP Figure 1-17 shows the basic appearance of M8600-04XFP, the line card of RG-S8614/S8610/S8606. M8600-04XFP provides four 10,000M XFP ports and features the functions of layer-2/3 switching. The M8600-04XFP module is hot swappable. Figure 1-17 Basic Appearance of the M8600-4X10G-XFP
1. Interface M8600-04XFP provides four 10,000M XFP ports and features layer-2/3 switching at the 10,000M wire speed. The XFP ports support short-wave (850nm, multi-mode), long-wave RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 27
(1310nm, single-mode) and long-distance (1550nm) 10,000M XFP fiber modules, thus facilitating configuration for users. 2. LEDs The M8600-04XFP module provides various system LEDs, as described in the following table: Table 1-16 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/ACT Port status LED OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port.
3. Technical Specifications Table 1-17 Technical specifications of M8600-04XFP Product Model M8600-04XFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE8023.ae, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type Four 10,000M XFP ports Transmission media For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT Hot swappability Supported Power consumption <100W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346*45mm ( L x W x H)
Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 28
1.6.9 M8600P-48GT/4SFP Figure 1-18 shows the basic appearance of the M8600P-48GT/4SFP, the linecard of the RG-S8614/S8610/S8606. M8600P-48GT/4SFP provides 44 10/100/1000BASE-T copper 1000M ports and 4 fiber/copper combo 1000M ports, and supports up to 48 1000BASE-T ports or 44+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals 4. The M8600P-48GT/12SFP module is hot swappable. Figure 1-18 Basic appearance of the M8600P-48GT/4SFP
1. Interface M8600P-48GT/4SFP provides 44 10/100/1000BASE-T copper 1000M ports and 4 fiber/copper combo 1000M ports, and supports up to 48 1000BASE-T ports or 44+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 4. The 1000M copper port supports PoE by default. Automatic MDI/MDI-X identification is available only when automatic negotiation is enabled. The SFP ports support short-wave (850nm, multi-mode) and long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M SFP fiberl modules and SFP copper ports, thus facilitating configuration for users. Note: The M8600P-48GT/4SFP provides 12 SFP 10/100/1000BASE-T fiber ports. In other words, each SFP port corresponds to one 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when auto negotiation is enabled.
Warning M8600P-48GT/4SFP does not support the hot pull-out operation. You need to perform the following operations to achieve it: 1. Disconnect all cables connected to the linecard; 2. Hold the Mode button for over three seconds until all LEDs on the linecard go off; 3. Configure the pull-out operation through software commands. (For relevant software configuration commands, refer to the corresponding software description.)
2. LEDs The M8600P-48GT/4SFP provides various system LEDs, as described in the following table: Table 1-18 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Mode LED status indication Green: Data exchange indication Orange: PoE status indication RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 29
Sign Description Detailed Information Link/A CT Port status LED Copper Port: When Mode is green (in switch mode): OFF: Port is not linked. Green: Port is linked at 1000M. Orange: Port is linked at 10/100M. Flashing: Data is transmitted on the port. When Mode is orange (in PoE mode): Off: The PoE device does not work normally. Green: The PoE device works normally. Orange: The PoE device is overloaded. Red: The port cannot be powered. Fiber Port: OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port. 3. Technical Specifications Table 1-19 Technical specifications of the M8600P-48GT/4SFP Product Model M8600P-48GT/4SFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.3af, IEEE 802.1D and IEEE 802.1Q 802.1X authentication Port type 44 10/100/1000BASE-T copper 1000M ports and 4 fiber/copper combo 1000M ports; Up to 48 1000BASE-T ports, or 44+M 1000BASE-T ports and N 1000BASE-X ports where M plus N equals to 4. Up to 48 PoE ports. Transmission media 10/100/1000BASE-TX: 100m (Category-5 or above unshield pair twists or pair twists) For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT, mode Hot swappability Supported Power consumption <100W+15.4xN (N indicates the PoE port being used, of which the value is less than 48.) EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 30
Product Model M8600P-48GT/4SFP Weight Net weight: 2.8 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.10 M8600-24SFP Figure 1-19 shows the basic appearance of M8600-24SFP, the line card of RG-S8614/S8610/S8606. M8600-24SFP provides 24 SFP ports supporting 1000BASE-X and 100BASE-X modes. It features layer-2/3 switch and routing. The M8600-24SFP module is hot swappable. Figure 1-19 Basic appearance of M8600-24SFP
1. Interface M8600-24SFP provides 24 1000M and 100M combo SFP ports, that is, it supports 1000BASE-X and 100BASE-X modes. It features layer-2/3 switching. The SFP ports support short-wave (850nm, multi-mode) and long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M/100M SFP fiber modules and SFP copper ports. The module is hot swappable. 2. LEDs The M8600-24SFP module provides various system LEDs, as described in the following table: Table 1-20 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/ACT Port status LED OFF: Port is not linked. Green: The 1000BASE-X Port is linked. Flashing green: Data is transmitted on the 1000BASE-X port. Orange: The100BASE-X port is linked. Flashing orange: Data is transmitted on the 100BASE-X port. 3. Technical Specifications Table 1-21 Technical specifications of the M8600-24SFP Product Model M8600-24SFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type 24 SFP ports (supporting 1000BASE-X/100BASE-X) RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 31
Product Model M8600-24SFP Transmission media For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT LEDs Hot swappability Supported Power consumption <75W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.11 M8600-MPLS Figure 1-22 shows the basic appearance of M8600-MPLS. M8600-MPLS is an agent card that supports MPLS. It does not provide any external port. Figure 1-22 Basic appearance of M8600-MPLS 1. LEDs The M8600-MPLS module provides the system LEDs, as described in the following table: Table 1-26 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. 3. Technical Specifications Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 32
Table 1-27 Technical specifications of M8600-MPLS Product Model M8600-MPLS Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication LED Status Hot swappability Supported Power consumption <100W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.12 M8600-NMM Figure 1-23 shows the basic appearance of M8600-NMM. M8600-NMM is an agent card that supports network flow control. It does not provide any external port. Figure 1-23 Basic appearance of M8600-NMM
1. LEDs The M8600-NMM provides the system LEDs, as described in the following table: Table 1-28 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. 3. Technical Specifications Table 1-29 Technical specifications of the M8600-NMM Product Model M8600-NMM LED Status Hot swappability Supported RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 33
Product Model M8600-NMM Power consumption <140W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 3.0 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.13 M8600-08XFP Figure 1-24 shows the basic appearance of M8600-08XFP, the line card of RG-S8614/S8610/S8606. M8600-08XFP provides 8 10,000M XFP ports and features the functions of layer-2/3 switching. The M8600-08XFP module is hot swappable. Figure 1-24 Basic Appearance of M8600-08XFP
1. Interface M8600-08XFP provides 8 10,000M XFP ports, which support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 10,000M XFP fiber ports. 2. LEDs The M8600-08XFP module provides various system LEDs, as described in the following table: Table 1-30 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/ACT Port status LED OFF: Port is not linked. Green: Port is linked. Flashing green: Data is transmitted on the port.
Table 1-31 Technical specifications of the M8600-08XFP Product Model M8600-08XFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE8023.ae, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type 8 10,000M XFP ports Transmission media For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT Hot swappability Supported Power consumption <250W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 3.5 Kg Dimensions 436*346*45mm ( L x W x H) 1.6.14 M8600-02XFP-24SFP/12GT-E Figure 1-25 shows the basic appearance of M8600-02XFP-24SFP/12GT-E, the line card of RG-S8614/S8610/S8606. The M8600-02XFP-24SFP/12GT-E module provides 2 10,000M XFP ports, 12 1,000M SFP ports and 12 1,000M fiber/copper combo ports. It supports up to 2 XFP ports and 24 1000BASE-T ports, or 2 XFP ports, 12+M 1000BASE-T ports and N 1000BASE-T ports where M plus N equals 12. It features layer-2/3 switching. The M8600P-48GT/4SFP-E module is hot swappable. Figure 1-25 Basic appearance of M8600-02XFP-24SFP/12GT-E
1. Interface The M8600-02XFP-24SFP/12GT-E module provides 2 10,000M XFP ports, 12 1,000M SFP ports and 12 1,000M fiber/copper combo ports. It features layer-2/3 switching. When the function of automatic negotiation is enabled, the POE-supported 10/100/1000BASE-T copper port supports automatic MDI/MDI-X identification. The SFP ports support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 1000M SFP fiber ports and SFP copper ports. Note: The M8600-02XFP-24SFP/12GT-E module provides 12 10/100/1000BASE-T SFP fiber ports. In other words, each SFP port corresponds to one 10/100/1000BASE-T port, and only one port can be used at a time, with the other being unavailable. The automatic RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 35
MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when auto negotiation is enabled.
2. LEDs The M8600-02XFP-24SFP/12GT-E module provides various system LEDs, as described in the following table: Table 1-32 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Module Fiber Port Indication OFF: There is no fiber ports. Green: There is fiber ports. Link/AC T Port status LED OFF: Port is not linked. Green: Port is linked Flashing green: Data is transmitted on the port.
3. Technical Specifications Table 1-33 Technical specifications of the M8600-02XFP-24SFP/12GT-E Product Model M8600-02XFP-24SFP/12GT-E Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type Provides 12 1000M SFP ports and 12 1000M fiber/copper combo ports, which support 1000BASE-SX/LX,1000BASE-TX, 1000BASE-LH, 10/100/1000BASE-TX Transmission media 10/100/1000BASE-TX: 100m (Category-5 or above unshield pair twists or pair twists) For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. See Appendix A-Connectors and connecting Media. LED Status, Link/ACT, Module Hot swappability Supported Power consumption <75W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 36
Product Model M8600-02XFP-24SFP/12GT-E Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimension 436*346*45(L*W*H)mm 1.6.15 M8600-VSU-02XFP Figure 1-26 shows the basic appearance of M8600-VSU-02XFP, the line card of RG-S8614/S8610/S8606. The M8600-VSU-02XFP module supports VSU and provides 2 10,000M XFP ports. It features layer-2/3 linespeed switching. The M8600-VSU-02XFP module is hot swappable and support the hot-swappability on the XFP ports. Figure 1-26 Basic appearance of M8600-VSU-02XFP
1. Interface The M8600-VSU-02XFP module provides 2 10,000M XFP ports. It features layer-2/3 linespeed switching and supports VSU. The XFP ports support short-wave (850nm, multi-mode), long-wave (1310nm, single-mode) and long-distance (1550nm) 10,000M XFP fiber modules, thus facilitating configuration for users.
2. LEDs The M8600-VSU-02XFP module provides various system LEDs, as described in the following table: Table 1-34 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. Link/AC T Port status LED OFF: Port is not linked. Green: Port is linked Flashing green: Data is transmitted on the port.
Table 1-35 Technical specifications of the M8600-VSU-02XFP Product Model M8600-VSU-02XFP Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type Provides 2 10,000M XFP ports Transmission media For transmission media supported on a fiber port, refer to Appendix B-Mini-GIC and 10G XFP Modules. The transmission media that modules support may be updated at any time. For details, please contact Ruijie Networks. LED Status, Link/ACT Hot swappability Supported Power consumption <75W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 2.8 Kg Dimension 436*346*45(L*W*H)mm 1.6.16 M8600-FW Figure 1-27 shows the basic appearance of M8600-FW. M8600-FW is a service card that supports firewall. The linecard provides one console port and MGMT port for improving the firewall function. M8600-FW module is hot swappable. Figure 1-27 Basic appearance of M8600-FW
1. Interface The M8600-FW module provides 2 external ports: Console port: also the communication port using the RS-232 interface level with the RJ-45 connector, which is used to connect the terminal serial ports for the firewall debugging, configuration, maintenance, management and software program loading,ect. 10/100M MGMT port: also the 10/100Base-T Ethernet port with the RJ-45 connector, which is used to connect the terminal Ethernet ports for the program loading.
Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 38
2. LEDs The M8600-FW module provides various system LEDs, as described in the following table: Table 1-36 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. 10/100M MGMT port indicator LED(Link/ACT) OFF: Port is not linked. Green: 100M port is linked Yellow: 10M port is linked Flashing green: Data is transmitted on the port.
3. Technical Specifications Table 1-37 Technical specifications of the M8600-FW Product Model M8600-FW Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 803.ae, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type Provides 1 console port and 1 10/100M MGMT port; no switching port Transmission media NA LED Status, Link/ACT Hot swappability Supported Power consumption <90W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 4.5 Kg Dimension 436*346*45(L*W*H)mm 1.6.17 RG-WALL 1600 FW Module Figure 1-28 shows the basic appearance of RG-WALL 1600 FW Module. RG-WALL 1600 FW Module is a service card that supports firewall. The linecard provides one console port RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 39
and MGMT port for improving the firewall function. RG-WALL 1600 FW Module is hot swappable. Figure 1-28 Basic appearance of RG-WALL 1600 FW Module
1. Interface The RG-WALL 1600 FW Module provides 2 external ports: Console port: also the communication port using the RS-232 interface level with the RJ-45 connector, which is used to connect the terminal serial ports for the firewall debugging, configuration, maintenance, management and software program loading,ect. 10/100M MGMT port: also the 10/100Base-T Ethernet port with the RJ-45 connector, which is used to connect the terminal Ethernet ports for the program loading.
2. LEDs The RG-WALL 1600 FW Module module provides various system LEDs, as described in the following table: Table 1-38 LEDs on the front panel Sign Description Detailed Information Status System LED OFF: The module has not been powered on. Red: Module fault Flashing green: The module is initializing. Solid green: The module has finished initialization and can perform switching normally. 10/100M MGMT port indicator LED(Link/ACT) OFF: Port is not linked. Green: 100M port is linked Yellow: 10M port is linked Flashing green: Data is transmitted on the port.
3. Technical Specifications Table 1-40 Technical specifications of the RG-WALL 1600 FW Module Product Model M8600-FW Standard Compliance IEEE 802.3-2002 IEEE 803.ab, IEEE 803.ae, IEEE 802.1D, and IEEE 802.1Q 802.1X authentication Port type Provides 1 console port and 1 10/100M MGMT port; no switching port Transmission media NA LED Status, Link/ACT Hot swappability Supported Chapter 1 Product Overview RG-S8600 Series Hardware Installation Guide 40
Product Model M8600-FW Power consumption <90W EMC GB9254-1998 FCC Class A Safety regulation GB4943-2001 Operating temperature 0 to 40#C Storage temperature -40 to 70#C Operating humidity 10% to 90% RH Weight Net weight: 4.5 Kg Dimension 436*346*45(L*W*H)mm 1.6.18 M8614/M8610/M8606-Fan M8614-Fan is the fan module of RG-S8614, M8610-Fan is the fan module of RG-S8610 and M8606-Fan is the fan module of RG-S8606. The M8614/M8610/M8606-Fan provides a sound heat dissipation system for the entire system to ensure stable operation. Fan model M8614 M8610 M8606 Ventilation criterion 118CFM*6 118CFM*6 118CFM*6 Power consumption 120W 60W 60W Weight 5.825kg 4.29kg 5.46kg Dimensions 286.4*690.2*75.7mm ( L x W x H) 432*374*66mm ( L x W x H) 432.4*405.4*46.8mm ( L x W x H) Note: The length of M8614/M8606 fan module excludes the length of handle and captive screw. The M8614/M8610/M8600-Fan module provides various system LEDs, as described in the following table: Table 1-41 LEDs on the front panel Sign Description Detailed Information Power Power LED OFF: The fan tray has not been powered on. Solid green: The fan module is normally powered on. Alarm Alarm LED OFF: Normally working Red: The fan tray fails. Note: In the RG-RG-S8614/RG-S8610/RG-S8606 system, when the M8614/M8610/M8606-Fan has an alarm, it means that the fan tray has failed. In this case, you should replace the failed one with a normal one immediately, preferably within 10 minutes. The M8614/M8610/M8606-Fan is hot swappable. RG-S8600 Series Hardware Installation Guide Chapter 1 Product Overview 41
1.6.19 RG-PA1200/PA1200E/PA2000 Power Module As the AC power module of the system, RG-PA1200/PA1200E/PA2000 supplies 110/220V AC power supply for RG-S8614/S8610/S8606. Module model RG-PA1200 RG-PA2000 RG-PA1200E Rated voltage 100VAC to 240VAC, 50Hz to 60Hz 100VAC to 240VAC, 50Hz to 60Hz 100VAC to 240VAC, 50Hz to 60Hz Maximum voltage 90VAC to 264VAC, 47Hz to 63Hz 90VAC to 264VAC, 47Hz to 63Hz 90VAC to 264VAC, 47Hz to 63Hz Maximum output power 90VAC to 264VAC; power:1200W 90VAC to 176VAC; power:1200W 176VAC to 264VAC; power:2000W 90VAC to 264VAC; power:1200W
Note: The RG-S8614/S8610/S8606 system supports 1+1 redundancy for the AC power supply. For higher stability and reliability of the entire system, you are recommended to configure 1+1 redundancy of the M8600-PA1200E/PA2000 for the RG-S8614/S8610/S8606. It shall use 16A power line for RG-PA1200E/PA2000 power module. 1.6.20 RG-PD1200/ PD2000 Power Module As the DC power module of the system, the RG-PD1200/PD 2000 supplies the intereface of -48V DC power supply for the RG-S8614/S8610/S8606. Note: The RG-S8614/S8610/S8606 system supports 1+1 redundancy for the DC power supply. For higher stability and reliability of the entire system, you are recommended to configure 1+1 redundancy of the M8600-PD1200/PD2000 for the RG-S8614/S8610/S8606.
Chapter 2 Preparation before Installation RG-S8600 Series Hardware Installation Guide 42
Preparation for Installation 2.1 Safety Suggestions To avoid bodily injury and equipment damage, please carefully read the safety suggestions before you install RG-S8614/S8610/S8606. Note: The following safety suggestions do not cover all possible dangers. 2.1.1 Safety Precautions for Installing the System n Keep the chassis clean, free from any dust. n Do not place the equipment in a walking area. n Do not wear loose clothes or any other things that may be caught by the chassis during installation and maintenance. n Turn off all power supplies and unplug all power cables before you remove the chassis. 2.1.2 Safety Precautions for Removal RG-S8614/S8610/S8606 is large and heavy. When you handle them, please pay attention to the following requirement: n Avoid moving the equipment frequently. n At least two people are needed to move the equipment. Do not attempt to move the equipment by one people only. n Keep balance when moving the equipment, and avoid injuring your leg and feet or spraining your waist. n Turn off all power supplies and unplug all power cables before you remove the equipment. n First remove all the linecards, fan tray, and power module from the chassis before you move the RG-S8614/S8610/S8606 by using the handles on both sides, to avoid any damage. RG-S8600 Series Hardware Installation Guide Chapter 2 Preparation before Installation 43
Figure 2-1 Correctly move the RG-S8614 switch
Figure 2-2 Correctly move the RG-S8610 switch
Figure 2-3 Correctly move the RG-S8606 switch
Chapter 2 Preparation before Installation RG-S8600 Series Hardware Installation Guide 44
Warning Do not move the equipment by grasping the panel, power supply handle, ventilation holes of the chassis, as they are not designed to bear the weight of the entire equipment. This may cause damage or even injure you. 2.1.3 Electrical Safety n Please observe local regulations and specifications when performing electrical operations. Relevant operators must be qualified. n Please carefully check for any potential danger in the working area, for example, ungrounded power supply, unreliable grounding of the power supply and damp/wet ground or floor. n Find out the location of the emergency power supply switch in the room before installation. First cut off the power supply in case of an accident. n Do not maintain the equipment alone when it is energized, unless absolutely necessary. n Be sure to make a careful check before you shut down the power supply. n Do not place the equipment in a damp/wet location. Do not let any liquid enter the chassis n Connect the negative and positive lines correctly according to the instructions when DC power supply is used.
Warning 1. Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electrical attack, thus causing severe even fatal damages to human bodies and equipment. 2. Direct or indirect touch through a wet object on high-voltage and mains supply can bring a fatal danger. 2.1.4 Static Discharge Damage Prevention Although much has been done in RG-S8614/S8610/S8606 to prevent static electricity, great damage may be caused to the circuitry and equipment when the static electricity exceeds a certain limit. In the communication network of the RG-S8614/S8610/S8606, electrostatic induction may come from the following sources: n External electric field produced by the high-voltage supply cable, lightning, etc; n Internal systems such as the indoor floor and the entire structure. To prevent damage from static electricity, you must pay attention to the following: 1. Properly ground the equipment. 2. Take dust prevention measures in the room. 3. Maintain an appropriate humidity. 4. Always wear an anti-static wrist strap when you touch any circuit board. 5. Try to hold a circuit board by its edges. Do not touch any components or the PCB. 6. Do not let any clothes touch a circuit board. An antistatic wrist strap can only prevent human static electricity from damaging the circuit board, but cannot prevent any static electricity on clothes. RG-S8600 Series Hardware Installation Guide Chapter 2 Preparation before Installation 45
2.1.5 Laser Safety Among the modules supported by RG-S8614/S8610/S8606, there are a great number of optical modules that are Class I laser products. Therefore, pay attention to the following during your use of this product: n When a fiber transceiver works, ensure that the port has been connected with an fiber or is covered with a dust cap so as to keep out dust and avoid burning your eyes. n Do not stare into any optical port.
Danger Do not stare into any optical port under any circumstances, as this may cause permanent damage to your eyes. 2.2 Installation Site Requirements RG-S8614/S8610/S8606 must be used in the room. To ensure normal operation and a prolonged use life of the equipment, the installation site must meet the following requirements. 2.2.1 Rack Mounting Requirements To mount the RG-S8614/S8610/S8606 in a frame, verify that the frame meets the following conditions: n Install the switch in an open cabinet as much as possible. If you install the switch inside a closed cabinet, be sure that the cabinet has a good ventilation and heat dissipation system. n Be sure that the cabinet is firm enough to bear the weight of the RG-S8614/S8610/S8606 and its installation accessories. n Be sure that the dimensions of the cabinet is appropriate for installation of the RG-S8614/S8610/S8606 that can reserve a certain space for the front, rear, left and right panels for heat dissipation. n The frame should be properly grounded. 2.2.2 Ventilation Requirements Figure 2-4, 2-5, 2-6 shows the ventilation requirements of the RG-S8614/S8610/S8606. Sufficient space must be reserved at the ventilation openings for ventilation. After connecting various cables, you should bundle the cables or place them in the cabling rack to avoid blocking air inlets. Chapter 2 Preparation before Installation RG-S8600 Series Hardware Installation Guide 46
Figure 2-4 Ventilation of RG-S8614
Figure 2-5 Ventilation of RG-S8610
Figure 2-6 Ventilation of RG-S8606 RG-S8600 Series Hardware Installation Guide Chapter 2 Preparation before Installation 47
2.2.3 Temperature and Humidity Requirements To ensure the normal operation and a prolonged use life of the RG-S8614/S8610/S8606, you must maintain an appropriate temperature and humidity in the equipment room. Too high or low temperature and humidity for a long period of time may damage the equipment. n In an environment with high relative humidity, the insulating material may have bad insulation or even leak electricity, and sometimes the materials may suffer from mechanical performance change and metallic parts may get rusted. n On the other hand, in an environment with low relative humidity, the insulating strip may dry and shrink, and static electricity may occur easily and endanger the circuit on the equipment. n In an environment with high temperature, the equipment is subjected to even greater harm, as its performance may degrade significantly and its useful life may be shortened in the case of long-term exposure that expedites the aging process. Therefore, the ambient temperature and humidity of the RG-S8614/S8610/S8606 equipment must meet the requirements listed in Table 2-1: Table 2-1Temperature and humidity requirements of the RG-S8614/S8610/S8606 Temperature Relative Humidity Working condition Non-working condition Working condition Non-working condition 0&C-40&C -40&C-70&C 10%-90% 10%-95%
Note: The ambient temperature and humidity are measured at the point that is 1.5m above the floor and 0.4m before the equipment when there is no protective plate in front or back of the equipment rack. Chapter 2 Preparation before Installation RG-S8600 Series Hardware Installation Guide 48
2.2.4 Cleanness Requirements Dust poses the top threat to the running of the equipment. The indoor dust falling on the equipment may be adhered by the static electricity, causing bad contact of the metallic joint. Such electrostatic adherence may occur more easily when the relative humidity is low, not only affecting the use life of the equipment, but also causing communication faults. Table 2-2 shows the requirements for the dust content and granularity in the equipment room. Table 2-2 Requirements for the dust content and granularity in the equipment room Maximum diameter ("m) 0.5 1 3 5 Maximum density (Particles/m 3 ) 1.4 x 10 7 x 10 2.4 x 10 1.3 x 10 Note: The air filter of the RG-S8614/S8610 must be cleaned at interval to ensure good ventilation and dust prevention. Apart from dust, the salt, acid and sulfide in the air in the equipment room must also meet strict requirements; as such poisonous substances may accelerate the corrosion of the metal and the aging of some parts. The equipment room should be protected from the intrusion of harmful gases (for example, sulfur dioxide, sulfured hydrogen, nitrogen dioxide, and chlorine), whose requirements are listed in Table 2-3. Table 2-3 Requirements for harmful gases in the equipment room Gas Average (mg/m 3 ) Maximum (mg/m 3 ) Sulfur dioxide 0.2 1.5 Sulfured hydrogen 0.006 0.03 Nitrogen dioxide 0.04 0.15 Ammonia 0.05 0.15 Chlorine 0.01 0.3 2.2.5 Power Requirements When the RG-S8614/S8610/S8606 uses the AC power supply: RG-PA1200: AC input voltage: 90Vac to 264Vac, 47Hz to 63Hz RG-PA1200E: AC input voltage: 90Vac to 264Vac, 47Hz to 63Hz RG-PA2000: AC input voltage: 90Vac to 264Vac, 47Hz to 63Hz When the RG-S8614/RG-S8610/RG-S8606 uses the DC power supply: RG-PD1200: DC input voltage: DC - 36Vdc to -72Vdc RG-PD2000: DC input voltage: DC - 36Vdc to -72Vdc RG-S8600 Series Hardware Installation Guide Chapter 2 Preparation before Installation 49
Note: The RG-S8614/S8610/S8606 provides 1+1 redundancy of power supply. You are recommended to use multiple power supplies for the equipment to ensure its continuous and stable operation by avoiding the impact of unexpected power failures on the equipment. 2.3 System Grounding Requirements A good grounding system is the basis for the stable and reliable operation of the RG-S8614/S8610/S8606. It is the key to prevent lightning stroke and resist interference. Please carefully check the grounding conditions on the installation site according to the grounding requirements, and perform grounding properly as needed. 2.3.1 Safety Ground The equipment using AC power supply must be grounded by using the orange/green safety grounding cable. Otherwise, when the insulating resistance decreases the power supply and the enclosure in the equipment, electric shock may occur. 2.3.2 Lightning Ground The lightning protection system of the facility is a separate system that consists of the lightning rod, down lead conductor and the connector to the grounding system, which usually shares the power reference ground and orange/green safety cable ground. The lightning discharge ground is for the facility only, irrelevant to the equipment. 2.3.3 EMC Ground The ground required for EMC design includes shielding ground, filter ground, noise and interference suppression, and level reference. All the above constitute the comprehensive grounding requirements. The grounding resistance should be less than 1'. The RG-S8614/S8610/S8606 chassis is installed with one grounding pole for shell protection which is required to connected the grounding pole of the cabinet, as shown in Figure 2-7. Figure 2-7 Grounding of the RG-S8614/S8610/S8606
Chapter 2 Preparation before Installation RG-S8600 Series Hardware Installation Guide 50
To ensure that the equipment works well, you must connect cables properly. Before you connect the cables, please carefully read the following precautions. 2.3.4 EMI Consideration Various interference sources, from either outside or inside the equipment or application system, affect the system in the conductive ways such as capacitive coupling, inductive coupling, and electromagnetic radiation. There are two types of electromagnetic interferences: radiated interference and conducted interference, depending on the type of the propagation path. When the energy, often RF energy, from a component arrives at a sensitive component via the space, the energy is known as radiated interference. The interference source can be both a part of the interfered system and a completely electrically isolated unit. Conducted interference results from the electromagnetic wire or signal cable connection between the source and the sensitive component, along the cable the interference conducts from one unit to another. Conducted interference often affects the power supply of the equipment, but can be controlled by a filter. Radiated interference may affect any signal path in the equipment, and is difficult to shield. 1. Effective measures should be taken for the power system to prevent the interference from the electric grid. 2. The working ground of the routers should be properly separated and kept as far as possible from the grounding device of the power equipment or the anti-lightning grounding device. 3. Keep the equipment away from high-power radio transmitter, radar transmitting station, and high-frequency large-current device. 4. Measures must be taken to isolate static electricity. 2.3.5 Precaution for Fiber Connection Before connecting the fibers, you should ensure that the type of optical connector and the type of fibers match the type of the optical interface used. Moreover, you should pay attention to the Tx and Rx directions of the fiber. The Tx end of this equipment should be connected to the Rx end of the peer equipment, and the Rx end of this equipment to the Tx end of the peer equipment. 2.4 Installation Tool Requirements The following table shows installation tools. Table 2-4 List of installation tools Common tools Cross screwdriver, straight screwdriver, related electric and optical cables Bolts, diagonal pliers, straps Special-purpose tools Anti-static tool Meter Multimeter Note: RG-S8614/S8610/S8606 series is not shipped with a tool kit. You need to prepare a tool kit by yourself. RG-S8600 Series Hardware Installation Guide Chapter 2 Preparation before Installation 51
2.5 Unpacking Requirements 2.5.1 Goods Checklist 1. RG-S8614/S8610/S8606 chassis carton n An equipment with various panels installed and adjusted properly n Screws n Documentation n Packing list 2. RG-S8614/S8610/S8606 accessory carton n AC or DC power module in accordance with the required configuration n Cabling Rack (only for RG-S8610) n Air filter(for RG-S8614/S8610) n Handles n Fan tray n Power supply cords (only for AC power supply) n Screws n Documentation n Packing list 3. Module carton n Various modules n Packing list n Documentation Note: A normal delivery should contain the above mentioned items, which may differ from the actual delivery, depending on purchase contracts. Please check your goods carefully against the packing list or purchase contract. If you have any questions or there are any errors, please contact your distributor.
Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 52
Switch Installation Note: 1. Before you install the RG-S8614/S8610/S8606, make sure you have carefully read Chapter 2 and this chapter. 2. Be sure that the requirements set forth in Chapter 2 have been met. RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 53
3.1 Installation Flow
DC AC Assemble RG-S8614/S8610/S8606 before installation Install the cabinet MountRG-S8614/S8610/S86 06 into the cabinet Ground the system Connect the power supply (AC or DC) Insert various modules Connect external port cables or fibers of various modules Bind cables or fibers Installation check End Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 54
3.2 Installation Verification The RG-S8614/S8610/S8606 is complicated equipment, so you must carefully plan and arrange the installation location, networking mode, power supply, and wiring before installation. Verify the following before installation: n The installation location is of a good air flow. n The installation location meets the temperature and humidity requirements of the equipment. n The qualified power supply is available at the installation location. n The related network cables have already been deployed at the installation location. n Rated DC or AC power supply is selected. 3.3 Cabinet Installation 3.1.1 Precautions When you install the cabinet, pay attention to the following: n All expansion bolts for fastening the cabinet base to the ground should be installed and tightened in sequence from bottom up (large plain washer, spring washer, and nut), and the installation holes on the base and the expansion bolts should be well aligned. n After the cabinet is installed, it should be stable and still. n After the cabinet is installed, it should be vertical to the ground. n When multiple cabinets are put side by side in the room, they should be aligned in a straight line, with an error less than 5 mm. n The front/back doors of the cabinet should be properly installed. You can open and close them smoothly. The locks should work normally, and all keys should be complete. n There should be no unnecessary formal labels inside the cabinet and on various boards. n Blank panels should be installed completely. n Fastening screws of various devices in the cabinet of the same model should be ready and tightened. n Various boards of the equipment should be installed securely, and the fastening screws on the panel should be tightened. n All wiring inlets at the top and bottom of the cabinet should be installed with rodent-resistant nets where the seams should be no more than 1.5 cm in diameter, to prevent rodents and other small animals from entering the cabinet. n Antistatic wrist straps should be provided in the cabinet. 3.1.2 Simple Installation Steps 1. Plan the available space before installing the cabinet. You must reserve sufficient space for front and back doors for maintenance. 2. Mount and fasten the 19inch cabinet at the designed location as planned. 3. Install the appropriate chute and cables. 4. Install the tray and wiring layer on the rack according to the configuration of one rack with one cabinet installed or one rack with multiple cabinets installed. RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 55
3.2 Mounting into the Cabinet 3.2.1 Precautions Before mounting RG-S8614/S8610/S8606 into the cabinet, first verify that the front and back brackets of the cabinet are at the right locations. If the bracket is too far forward, the front panel of the equipment may be too close to the front door, so that the front door cannot be closed when network cables and pigtail fibers are connected. Usually, you should reserve at least 10mm between the front panel of the equipment and that of the cabinet after installation. Before mounting into a cabinet, you need to address the following conditions: Fasten the cabinet and insert various modules in the frame properly. Remove any obstacle in the frame and the surrounding environment. Prepare the equipment and move it to the place near the frame where you can handle it easily. Note: Before mounting the chassis into the cabinet, you should disassemble its four wheels. The newly-supplied product has no wheels. 3.2.2 Simple Installation Steps 1. Levelly lift the RG-S8614/S8610/S8606 by two people on both sides, and slowly move it to the front of the frame. 2. Levelly lift the RG-S8614/S8610/S8606 to a position slightly higher than the tray or the slide rail of the cabinet, put the equipment onto the tray or the slide rail, and push it into the cabinet. 3. Fasten the RG-S8614/S8610/S8606 onto the cabinet with screws. There are fastening notches on both the sides of the front panel on the equipment frame. Use screws to fasten them to the fastening bracket of the cabinet. After fastened, the equipment should be stable and still in the cabinet. 3.3 Installing Fan Tray The RG-S8614/S8610/S8606 provides a ventilation system: M8614-FAN for RG-S8614, M8610-FAN for RG-S8610 and M8606-FAN for RG-S8606. Install the fan tray according to the following steps: 1. Remove the blank panel of the fan tray by loosing the captive screws with a straight screwdriver and the cross screws with a cross screwdriver. 2. Push the fan into the cabinet along the guide rail. 3. Tighten the captive screws with a straight screwdriver. Figure 3-2 ,3-3, 3-4 show the installed fan tray. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 56
Figure 3-2 Installing the fan tray of the RG-S8614 switch
Figure 3-3 Installing the fan tray of the RG-S8610 switch
Figure 3-4 Installing the fan tray of the RG-S8606 switch RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 57
3.4 Installing Power Supply RG-S8614/S8610/S8606 system provides RG-PA1200, RG-PA1200E and RG-PA2000, as well as RG-PD1200 and RG-PD2000, which can be installed in the same way according to the following steps: 1. Remove any blank panel of the power module by loosening the two cross screws with a cross screwdriver, as shown in Figure 3-5, 3-6,3-7. Figure 3-5 Install the power supply of the RG-S8614 switch
Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 58
Figure 3-6 Install the power supply of the RG-S8610 switch
Figure 3-7 Install the power supply of the RG-S8606 switch
2. Insert the power supply module into the cabinet along the guide rail, as shown in Figure 3-8, 3-9, 3-10. Figure 3-8 Install the power supply of the RG-S8614 switch
RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 59
Figure 3-9 Install the power supply of the RG-S8610 switch
Figure 3-10 Install the power supply of the RG-S8606 switch
3. Tighten the screws on both sides of the power supply by using a straight screwdriver, as shown in Figure 3-11, 3-12, 3-13. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 60
Figure 3-11 Install the power supply of the RG-S8614 switch
Figure 3-12 Install the power supply of the RG-S8610 switch
RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 61
Figure 3-13 Install the power supply of the RG-S8606 switch
3.5 Installing Handle RG-S8614/S8610/S8606 comes with handles for easy handling. The handle can be installed according to the following steps: 1. Align the handle with the sunk hole on the fastening bar; 2. Tighten the cross M4 sunk screws provided with the unit, as shown in Figure 3-14, 3-15, 3-16. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 62
Figure 3-14 Install the handle of the RG-S8614 switch
Figure 3-15 Install the handle of the RG-S8610 switch
Figure 3-16 Install the handle of the RG-S8606 switch RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 63
3.6 Installing Cabling Rack for RG-S8610 To install cabling rack for RG-S8610, do the following steps: 1. Remove the blank panel of the cabling rack by loosing the captive screws with a straight screwdriver and the cross screws with a cross screwdriver, as shown in Figure 3-17.. Figure 3-17 Install the cabling rack
Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 64
2. Install the panel of the cabling rack by tightening the two captive screws with a straight screwdriver and the four cross screws with a cross screwdriver, as shown in Figure 3-18. Figure 3-18 Install the cabling rack
3. Fasten the cabling rack by using the cross M3 screws provided, as shown in Figure 3-19. (The cabling rack is available in two sizes, and you can select the appropriate one) Figure 3-19 Install the cabling rack
RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 65
3.7 Installing Air Filter for RG-S8614/S8610 Simply push the air filter into the cabinet of the RG-S8614/S8610 along the guide rail, as shown in Figure 3-20, 3-21. Figure 3-20 Install the air filter of the RG-S8614 switch
Figure 3-21 Install the air filter of the RG-S8610 switch
Note: You are recommended to install the air filter as the last step of the chassis installation. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 66
3.8 Grounding A PGND is installed on the back of RG-S8614/S8610/S8606. You must first connect the PGND to the grounding terminal of the cabinet and then connect the grounding terminal to the grounding bar of the equipment room (or the analog bar if there are digital grounding bar and analog grounding bar). 3.8.1 Precautions n The sectional area of the grounding cable should be determined according to the possible maximum current. Cables of good conductor should be used. n Do not use bare wire. n The grounding resistance for combined grounding should be less than 1'. 3.8.2 Simple Grounding Steps 1. Release the nut on the rear grounding post of the equipment. 2. Lock the terminal of the grounding cable to the grounding pole. 3. Tighten the nut. 4. Connect the related terminals according to the above steps and the wiring diagram. 3.9 Connecting the DC Power Supply to the Power Module Connect DC power cables according to the mark and position instruction on RG-PD1200/RG-PD2000 panel of the DC power module, as shown in the following diagram. Figure 3-22 Connect DC power cables
3.9.1 Precautions n Before connecting the power supply, you must verify that the external power supply matches the power module installed with this equipment. RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 67
n Before connecting the power cable, be sure that the switch of the power module is at the OFF position. n The power cables of various colors must be connected to the appropriate wiring posts. n Be sure that the power cables connected are in good contact. 3.9.2 Simple Connection Steps 1. Remove the protection cover of the DC wiring terminal. 2. Lock the power cable to the appropriate terminal according to the identification, and tighten the pressing screw. 3. Put on the protection cover and tighten the screw. 4. Connect the other end of the power cable to the corresponding socket or connector. 3.10 Connecting the AC Power Supply to the Power Module Connect AC power cables according to the ID and position instruction on the RG-PA1200/PA1200E/ PA2000 panel of the AC power module, as shown in the following diagram. Figure 3-23 Schematic Diagrams for the Connection of the AC Power Cable
3.10.1 Precautions n Before connecting the power supply, you must verify that the external power supply matches the power module installed with this equipment. n Before connecting the power cable, be sure that the switch of the power module is at the OFF position. n The power cable with a standard 3-pin connector should be used for connection. n Be sure that the power cables connected are in good contact. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 68
3.10.2 Simple Connection Steps 1. Insert the plug of the power cable into the power module. 2. Connect the other end of the power cable to the corresponding socket or connector. 3.11 Connecting the Cables of the Management Module 3.11.1 Simple Connection Steps 1. Connect the end of the Ethernet cable with the RJ45 connector to the Ethernet port of the equipment management module (M8614/M8610/M8606-CMII), and the other end to the NM or control terminal. 2. Connect the end of the standard DB9 serial cable with the RS-232 serial port to the RS-232 serial port of the equipment management module, and the other end to the NM or control terminal. Note: The RG-S8614/S8610/S8606 system must have at least one management module to work normally. 3.12 Removing Boards from RG-S8614/S8610/S8606 3.12.1 Precautions Always wear an anti-static wrist strap when unplugging the module and the metallic part of the anti-static wrist strap should be fully touched with the skin. Besides, for the sake of security, please not touch any component of the module. 3.12.2 Steps for Removing Boards 1. Unplug all cables/fibers such as fibers and RJ45 twisted pairs from the panel. 2. Loosen two captive screws on the panel. 3. Draw out the board by holding the ejector with both hands, as shown in Figure 3-24, 3-25, 3-26. 4. Install the board panel to avoid the dust after removing the board and no new board will be installed.
Warning 1. Always wear an anti-static wrist strap before plugging/unplugging a board. 2. Do not hold the edge of the PCB or collide the components on the PCB. RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 69
Figure 3-24 Board components of the RG-S8614
Figure 3-25 Board components of the RG-S8610
Figure 3-26 Board components of RG-S8606 Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 70
3.13 Installing Boards on RG-S8614/S8610/S8606 3.13.1 Precautions Always wear an anti-static wrist strap when unplugging the module and the metallic part of the anti-static wrist strap should be fully touched with the skin. Besides, for the sake of security, please not touch any component of the module. 3.13.2 Simple Steps of Board Installation 1. Remove the appropriate component card or blank panel according to 3.14. 2. Replace it with the appropriate card and insert into the guide rail. 3. Push the card into position by using the ejector, and tighten the two captive screws on the card with a straight screwdriver.
Warning 1. Do not hold the edge of the PCB or collide the components on the PCB. 2. Do not plug/unplug a PCB module forcedly, use the ejector. 3.13.3 Precautions of Installing M8600-FW and RG-WALL 1600 FW Module Except for the above basic installation precautions, the following special precautions shall be paid attention to when installing the M8600-FW and RG-WALL 1600 FW module due to their great heat consumption: RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 71
1. For the RG-S8606, the S8606 ventilation board should be installed above the slot where the M8600-FW and RG-WALL 1600 FW module inserted; 2. For the RG-S8610, for the purpose of air ventilation, the blank panel should be inserted in the slot neighbored to the slot where the M8600-FW and RG-WALL 1600 FW module inserted; 3. Install the M8600-FW and RG-WALL 1600 FW module in the slot which is of good ventilation, such as the slot neighbored to the management board; 4. If the chassis fan tray does not work, neither can the M8600-FW and RG-WALL 1600 FW module work for a long time, for example, when maintaining and changing the chassis fan tray, the M8600-FW and RG-WALL 1600 FW module should be plugged out, or the time of maintaining and changing the fan tray should be controlled within half an hour. 3.14 Connecting the External Interface Cables 3.14.1 Precautions n Correctly distinguish single-mode and multi-mode fibers and ports. n Avoid bends of small radius at the connector. 3.14.2 Simple Connection Steps 1. Connect one end of the RJ45 connector for configuring Ethernet cables to the Ethernet interface of the device board and the other end to the NMS or a control terminal; or connect one end of the standard RJ45 serial port cable to the serial port of the device board and the other end to the NMS or a control terminal. 2. Insert the single-mode or multi-mode fiber into the appropriate interface according to the identification on the panel of the linecard. Distinguish the Rx/Tx end of the fiber. 3. Insert the twisted pair with the RJ45 port into the appropriate interface according to the identification on the panel of the linecard. Distinguish the crossover cable and straight-through cable. 4. Connect the cables and fibers of each board in sequence. 3.15 Binding the Cables 3.15.1 Precautions n The power cables and other cables should be bound in a visually pleasing way. n When you bind fibers, be sure that the fibers at the connectors have natural bends or bends of large radius. n Do not bind fibers and twisted pairs too tightly, as this may press hard the fibers and affect their useful life and transmission performance. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 72
3.15.2 Simple Binding Steps 1. Bind the drooping part of the fibers and twisted pairs of each board, and lead them to both sides of the chassis for convenience. For the RG-S8610, you can lead out the fibers and twisted pairs by using the cabling chute on the chassis. 2. On the both sides of the chassis, fasten the fibers or twisted pairs to the cabinet cable management ring or cabling chute. 3. For the power cables, you should bind them closely along the bottom of the chassis, in a straight line wherever possible. 3.16 Installation Verification 3.16.1 Verifying the Cabinet n Verify if the external power supply matches the distribution panel of the cabinet. n After installing the equipment, verify if the front/back cabinet doors can be closed. n Verify that the cabinet has been fastened completely, and does not move or tilt. n Verify that the equipment has been installed in the cabinet, and all the cables have been fastened to the cabinet. 3.16.2 Verifying the Cables n Verify that the fibers and twisted pairs match the ports. n Verify that the cables have been bound properly. 3.16.3 Verifying the Power Supply n Verify that the power cables are in good contact and comply with the safety requirements. n Verify that the power module has been fastened onto the equipment with the two screws on the panel. n Turn on the power switch and verify that the power module can work normally. 3.17 Upgrade Instruction for MEM-CM-512 Memory Bank 3.17.1 Precautions You must wear anti-static gloves or wrist straps when changing the memory bank for the sake of security. 3.17.2 Specification For the detailed specification information of memory bank, see Table 3-1: Table 3-1 Specification List Attribute Description RG-S8600 Series Hardware Installation Guide Chapter 3 Switch Installation 73
Type DDR SDRAM Capacity 512MB Dimension L: 67.60mm W: 31.75mm Pin Number 200 Applicable Modules M8606-CM II, M8610-CM II, M8614-CM II 3.17.3 Installation Instruction Use the following methods to change 512MB memory bank: 1. First confirm that the management board to be installed with the memory bank is powered down and the memory bank is installed in SD-DIMM soket(J111). 2. Installation steps: (1) Insert 512MB memory bank to SOP-DIMM soket tiltly and confirm that it has been tightly inserted.(in the direction that is about 30"with the management board) Figure 3-28: Replacing the memory bank
(2)Press the memory bank downward, in the direction that is vertically with the management board to lock the card buttons on both sides tightly. Then, the memory bank is paralleled to the management board. Figure 3-29: Replacing the memory bank Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 74
3.17.4 Installation Verification The memory bank can not be pressed and locked tightly into the slot if it is not installed properly for the existence of the card button structure. The memory bank can be pressed and locked tightly into the slot if it is installed properly.
RG-S8600 Series Hardware Installation Guide Chapter 4 Maintenance 75
Maintenance 4.1 RG-S8614/S8610/S8606 Monitoring When the RG-S8614/S8610/S8606 is running, you can monitor the status of each board by inspecting the status LED of the appropriate board. When the Status LED of a board is OFF, RED, or flashing, it means that the board is faulty, in which case you need to find out the cause, and turn off the power when necessary. When the Alarm LED of the main management board is red, it means that the system has a fault, in which case you can determine and eliminate the fault by viewing with the management software. When the Alarm LED of the fan tray is red, it means that the fan tray is faulty, in which case you need to replace or repair the fan tray. When the FAIL LED of the power supply is red, it means that the power supply is faulty, in which case you should replace it promptly. The RG-S8614/S8610/S8606 allows you to monitor various system status by executing the appropriate CLI commands, including: n Module/board in-position status n Port configuration information and status n Fan and power supply working status n Temperature status For the monitoring commands, see RG-S8600 series Software Configuration Guide. 4.2 RG-S8614/S8610/S8606 Hardware Maintenance 4.2.1 Board Maintenance To replace a board, do replacement according to the instructions provided in Section 3.14 and 3.15. 4.2.2 Ventilation System Maintenance n The fan in the equipment is provided with the fault monitoring signals. When the fan fails, an appropriate alarm will occur. n To replace the fan, first loosen the fastening screw on the fan tray. n Replace the failed fan with a good one. n Tighten the fastening screws of the fan tray. Chapter 4 Maintenance RG-S8600 Series Hardware Installation Guide 76
4.2.3 Power Supply Maintenance When the power supply fails, you only need to disconnect the power cable, loosen the two panel screws on the power module, unplug the power module, replace it with a good one, and tighten the panel screws, and then connect the power cables. 4.3 Replacing LCD The LCD installed on the top of the RG-S8614/S8610/S8606 chassis is hot swappable. You can replace the LCD without breaking off the operation of the device in case of a LCD failure. Note that n Handle the grooves on the both sides of the LCD with your hands and then disconnect the LCD from the chassis. Do not drag the cable forcibly. n The cable is fixed on the circuit board with a DB25 connector. Loosen the screws fixed the connector with a magnetic screwdriver (you had better use the screwdriver shipped with the product) to prevent the screwdriver or screws from contacting the electric elements on the circuit board. n Plug out the cable properly. Do not drag the cable forcibly. n Install the LCD: Match the DB25 connector of the cable against the corresponding connector on the circuit board and then insert it. Screw the connector with a magnetic screwdriver. At this point, the LCD works if the device works well. n Handle the LCD with your hands, match the clips against the aligning holes on the chassis and the push down the LCD properly Note: During the operation, it is necessary to wear the anti-static wrist strap and avoid contacting the circuit board with hands. 4.4 Remote Maintenance RG-S8614/S8610/S8606 supports remote maintenance. By utilizing the Internet, a user can realize communication through remote Telnet login. During installation and networking, RG-S8614/S8610/S8606 and the Internet are connected; therefore, the user can log in to the RG-S8614/S8610/S8606 via Telnet and maintain RG-S8614/S8610/S8606 remotely through various monitoring commands. RG-S8600 Series Hardware Installation Guide Chapter 5 Troubleshooting 77
Troubleshooting 5.1 General Installation Troubleshooting Flow
Abnormal working after installation Check the cabinet installation Check the mounting of the RG-S8610 switch in the cabinet Check the power connection Check the installation of the power module Check the linecards and other plug-in units on the backplane Check the installation and fastening of the linecards Check the indicators on the linecards Check the connection of the serial port and its parameters Check the connection of the fibers or cables of various ports Contact Technical Support of RUIJIE for hardware problems Chapter 5 Troubleshooting RG-S8600 SeriesHardware Installation Guide 78
5.2 Common Troubleshooting Procedures Fault 1: The system login password is lost. [Fault Description] The system login password of the switch is forgotten or lost, and so it is not possible to configure the data. [Troubleshooting] Please contact Ruijie Customer Service Department for technical support.
Fault 2: The AC power module does not work. [Fault Description] The Status LED of each linecard is OFF, the Power LED of the fan tray is OFF (only on the RG-S8610), and the fan does not work. The LED on the panel of the power module is OFF. The fan does not work. [Troubleshooting] First place the switches of all the power modules to OFF. Check if the cables of the cabinet have been correctly connected. Check whether the power cables are tightly connected to the cabinet power sockets and power modules. Check whether the power modules are installed correctly. If necessary, check whether the connectors on the backboard of the power system are tightened. Check if there is a mix of AC and DC power supplies.
Fault 3: The DC power module does not work. [Fault Description] The Status LED of each linecard is OFF, the Power LED of the fan tray is OFF(only on the RG-S8610), and the fan does not work. The LED on the panel of the power module is OFF. The fan does not work. [Troubleshooting] First place the switches of all the power modules to OFF. Check if the cables of the cabinet have been correctly connected. Check whether the cabinet power sockets and DC power modules are tightly connected in a correct way. Check whether the power modules are installed correctly. If necessary, pull out the power modules and check whether the connectors on the backboard of the power system are tightened. Check if there is a mix of AC and DC power supplies.
Fault 4: An exception occurs to the LEDs when linecards are powered on. [Fault Description] The Status LED of the linecard is OFF, flashing, or RED. The Link/ACT LED of the linecard is ON when no network cable or fiber is plugged. [Troubleshooting] RG-S8600 Series Hardware Installation Guide Chapter 5 Troubleshooting 79
Check if the linecard is firmly inserted. If so, install the linecard again and ensure that it is inserted into position before you tighten the fastening screws. If the linecard still does not work, check if the connector of the slot on the backplane is loose. If yes, insert the board to another slot for a try. If the slot and connection are not the cause, return the linecard for repair.
Fault 5: The LED is abnormal after a linecard works for some time. [Fault Description] The Status LED of the linecard is OFF or RED. The Link/ACT LED of the linecard is solid ON when no network cable or fiber is plugged. The fault remains after restart. [Troubleshooting] Check if the board gets loose. If so, install the linecard again and ensure that it is inserted into position before you tighten the fastening screws. If the linecard still does not work, check if the connector of the slot on the backplane is loose and check if the guide rail of the slot is deformed. If so, insert the board to another slot for a try. If the slot and connection are not the cause, return the linecard for repair.
Fault 6: The LED of the management board is abnormal. [Fault Description] The LED of the management board becomes abnormal after the board is powered on or works for some time. For example, the Status LED is flashing or OFF, and the Alarm LED is red. [Troubleshooting] Check if the management board gets loose. If so, install the management card again and ensure that it is inserted into position, before you tighten the fastening screws. If the linecard still does not work, check if the connector of the slot on the backplane is loose and check if the guide rail of the slot is deformed. If yes, insert the board to another slot for a try. If the slot and connection are not the cause, return the management card for repair. When the Alarm LED is red, the cause may be the fault of another module in the system, in which case you can check other modules (for example, linecard, fan, power, and overheating) for any alarm. If yes, you should first handle the faults of other modules. You can also identify the faults by logging in to the management software.
Fault 7: The fan tray does not work or an exception occurs to the LED. [Fault Description] After the system starts, the fans in the fan tray do not work or the Power LED is OFF, and the Alarm LED is red. [Troubleshooting] Check if the connection between the fan tray and the backplane is secure and if the connector gets loose. If the connection is secure, you need to replace the fan tray.
Fault 8: The serial port console has no output. [Fault Description] Chapter 5 Troubleshooting RG-S8600 SeriesHardware Installation Guide 80
After the system is started, the serial port console does not display any information. [Troubleshooting] Check whether serial port cables are connected correctly and whether the connected serial port is identical with that configured on the super terminal. Check whether the configuration of the serial port on the super terminal is the same as that described in RG-S8600 Software Configuration Guide. If not, modify the serial port configuration parameters. If there is still no serial port printed information, please contact Ruijie Customer Service Department for technical support.
Fault 9: The serial port console outputs illegible characters. [Fault Description] The serial port console outputs illegible characters. [Troubleshooting] Such problem is related to the settings of the serial port. Check if the settings of such parameters as the baud rate match those in RG-S8600 series Software Configuration Guide. RG-S8600 Series Hardware Installation Guide Appendix A Connectors and Connection Media 81
AppendixA Connectors and Connection Media 1.1000BASE-T/100BASE-TX/10BASE -T Port 1000BASE-T/100BASE-TX/10BASE-T is a port that supports adaptation of three rates, and automatic MDI/MDIX Crossover at these three rates. The 1000BASE-T complies with IEEE 802.3ab, and uses up to 100m of 100-ohm Category-5 or Supper Category-5 UTP or STP cable. The 1000BASE-T port uses four pairs of wires for transmission, all of which must be connected. Figure A-1 shows the connections of the twisted pairs used by the 1000BASE-T port: Figure A-1 Four twisted pairs of the 1000BASE-T Straight-Through Crossover Switch Switch 1TP0+ 1TP0+ 2TP0- 2TP0- 3TP1+ 3TP1+ 6TP1- 6TP1- 4TP2+ 4TP2+ 5TP2- 5TP2- 7TP3+ 7TP3+ 8TP3- 8TP3- Switch Switch 1TP0+ 1TP0+ 2TP0- 2TP0- 3TP1+ 3TP1+ 6TP1- 6TP1- 4TP2+ 4TP2+ 5TP2- 5TP2- 7TP3+ 7TP3+ 8TP3- 8TP3- In addition to the above cables, the 100BASE-TX/10BASE-T can also use up to 100m of 10Mbps 100-ohm Category-3, 4, 5 cables and 100Mbps 100-ohm Category-5 cables. Figure A-2 shows the connections of the twisted pairs of the 100BASE-TX/10BASE-T: Figure A-2 Twisted pairs of the 100BASE-TX/10BASE-T
Figure A-3 shows the connections of the straight-through and crossover twisted pairs of the 100BASE-TX/10BASE-T. Appendix A Connectors and Connection Media RG-S8600 Series Hardware Installation Guide 82
Figure A-3 Connections of the twisted pairs of the 100BASE-TX/10BASE-T
2. Fiber Connection For the fiber ports, select single-mode or multiple-mode fibers for connection according to the fiber module connected. The connection schematic diagram is shown in Figure A-4: Figure A-4 Schematic Diagram for Fiber Connection Switch Switch TX TX RX RX
RG-S8600 Series Hardware Installation Guide AppendixB Mini-GBIC and 10G XFP Modules i
AppendixB Mini-GBIC and 10G XFP Modules 100M SFP module, 1000M SFP module (Mini-GBIC module) and 10G XFP module are available to address the requirements of interface types of switch modules. You can select the SFP or XFP module to suit your specific needs. Below the models and technical specifications of some 100M SFP, 1000M SFP and 10G XFP modules are listed for your reference. 1. Models and Technical Specifications of the Mini-GBIC (SFP) Module Table B-1 GBIC and SFP transmitting and receiving sensitivity GBIC/SFP Wave-lengt h (nm) Fiber type Transmitting sensitivity/dBm Receiving sensitivity/dBm MIN MAX MIN MAX FE-SFP-LX-MM1310 1310 Multimode optic fiber -22 -14 -30 -14 FE-SFP-LH15-SM1310 1310 Single mode optic fiber -15 -8 -28 -8 FE-SFP-LH40-SM1310 1310 Single mode optic fiber -5 0 -34 -5 FE-SFP-ZX80-SM1550 1550 Single mode optic fiber -5 0 -34 -5 GBIC-SX /Mini-GBIC-SX 850 Multimode optic fiber -9.5 -4 -17 0 GBIC-LX /Mini-GBIC-LX 1310 Single mode optic fiber -9.5 -3 -20 -3 Mini-GBIC-LH40 1310 Single mode optic fiber -2 3 -22 -3 GBIC-ZX50 /Mini-GBIC-ZX50 1550 Single mode optic fiber -5 0 -22 -3 GBIC-ZX80 1550 Single mode 0 4.7 -22 -3 AppendixB Mini-GBIC and 10G XFP Modules RG-S8600 Series Hardware Installation Guide ii
/Mini-GBIC-ZX80 optic fiber GBIC-ZX100 /Mini-GBIC-ZX100 1550 Single mode optic fiber 0 5 -30 -9 GBIC-ZX120 /Mini-GBIC-ZX120 1550 Single mode optic fiber 0 5 -30 -9 SDH155-SFP-SX-MM850 850 Multimode optic fiber -10 -4 -25 0 SDH155-SFP-LH15-SM131 0 1310 Single mode optic fiber -15 -8 -34 -8 SDH155-SFP-LH40-SM131 0 1310 Single mode optic fiber -5 0 -34 -8 SDH155-SFP-LH80-SM131 0 1310 Single mode optic fiber -5 0 -34 -8 Note: Before using optic moduloes, pay more attention to receiving sensitivity, which may be less than the index in real environment. Connection failure or mass packet loss may occur on modules. If the real receiving sensitivity is larger than the maximum index, which means damage to the module. Table B-2 Module cabling specification GBIC/SFP Transmissi on rate Wavelength (nm) Media Type Core Size (nm) Maximum cabling distance FE-SFP-LX-MM1 310 100M 1310 Multi mode optic fiber 62.5/125 2 kilometers FE-SFP-LH15-S M1310 100M 1310 Single mode optic fiber 9/125 15 kilometers FE-SFP-LH40-S M1310 100M 1310 Single mode optic fiber 9/125 40 kilometers FE-SFP-ZX80-S M1550 100M 1550 Single mode optic fiber 9/125 80 kilometers GBIC-SX/Mini- GBIC-SX 1000M 850 Multimode fiber 62.5/125 50/125 275m 550m GBIC-LX/Mini- GBIC-LX 1000M 1300 Single-mode fiber 9/125 10 kilometers Mini-GBIC-LH4 0 1000M 1310 Single mode fiber 9/125 40 kilometers GBIC-ZX50/Mi ni-GBIC-ZX50 1000M 1550 Single-mode fiber 9/125 50 kilometers RG-S8600 Series Hardware Installation Guide AppendixB Mini-GBIC and 10G XFP Modules iii
GBIC/SFP Transmissi on rate Wavelength (nm) Media Type Core Size (nm) Maximum cabling distance GBIC-ZX80/Mi ni-GBIC-ZX80 1000M 80 kilometers GBIC-ZX100/M ini-GBIC-ZX10 0 1000M 100 kilometers GBIC-ZX120/M ini-GBIC-ZX12 0 1000M 120 kilometers SDH155-SFP-SX -MM850 100M 850 Multi mode fiber 62.5/125 1 kilometer SDH155-SFP-LH 15-SM1310 100M 1310 Single mode fiber 9/125 15 kilometers SDH155-SFP-LH 40-SM1310 100M 1310 Single mode fiber 9/125 40 kilometers SDH155-SFP-LH 80-SM1550 100M 1550 Single mode fiber 9/125 80 kilometers
Note: Given the receiving sensitivity, when short-distance single mode optic fibers are used, you should insert an optic attenuation among links to release damage to the following optic modules: FE-SFP-LH40-SM1310, FE-SFP-ZX80-SM1550, GE-SFP-LH40-SM1310, GBIC-ZX50 /Mini-GBIC-ZX50, GBIC-ZX80 /Mini-GBIC-ZX80, GBIC-ZX100 /Mini-GBIC-ZX100, GBIC-ZX120 /Mini-GBIC-ZX120, SDH155-SFP-LH40-SM1310, and SDH155-SFP-LH80-SM1550.
Table B-3 Cabling specification for 1000Base-T port 1000Base-T Copper cable type Cabling distance GBIC-GT Cat-5 or above unshield pair twists or pair twists 100m Mini-GBIC-GT Cat-5 or above unshield pair twists or pair twists 100m AppendixB Mini-GBIC and 10G XFP Modules RG-S8600 Series Hardware Installation Guide iv
2. Models and Technical Specifications of the 10G XFP Module Table B-4 Models and Technical Specifications of the 10G XFP Module Model Wavelengt h (nm) Media Type Core Size (nm) Modular Bandwidth (MHz/km) Transmi- ssion Distance Optical Intensity (dBm) Reception sensitivity (dBm) 10GBAS E-SR-XF P 850 Multimode fiber (LC connector) 62.5
200 160 Max: 33 m Max: 22 m Min:-5 Max: -1.0 Min:-7.5 Max: 0.5 50
2000 500 400 Max: 300 m Max: 82 m Max: 66 m 10GBAS E-LR-XF P 1310 Single-mode fiber (LC connector) 9 N/A Max. 10KM; Min:-4.8 Max: 0.5 Min:-10.3 Max: 0.5 10GBAS E-ER-XF P 1550 Single-mode fiber (LC connector) 9 N/A Max. 40KM; Min:--1 Max: 2 Min:-11.3 Max: -1 XG-XFP- ZR80-Sm -1550 1550 Single-mode fiber (LC connector) 9 N/A Max. 80KM; Min:0 Max: 4 Min:-23 Max: -7 Note: For the 10GBASE-ER-XFP, you need to avoid the overload of the optical receiver when the transmission distance is short. As long as the optical power at the reception end of the fiber is greater than or equal to -1dBm, you should add an appropriate optical attenuator between the fiber at both ends of the link and the reception port of the 10GBASE-ER-XFP, so that the optical power at the reception end falls under -1dBm. For XG-XFP-ZR80-SM1550, you need to avoid the overload of the optical receiver when the transmission distance is short. As long as the optical power at the reception end of the fiber is greater than or equal to -7dBm, you should add an appropriate optical attenuator between the fiber at both ends of the link and the reception port of the module, so that the optical power at the reception end falls under -7dBm.