0 evaluări0% au considerat acest document util (0 voturi)
265 vizualizări24 pagini
The grase-conf-openvpn package will connect your hotspot computer to a virtual private network, that allows remote access to your computer on that virtual private network. This connection is the same as if I was sitting on your WiFi network, so I am unable to access any other device other than your Grase Hotspot machine.
The grase-conf-openvpn package will connect your hotspot computer to a virtual private network, that allows remote access to your computer on that virtual private network. This connection is the same as if I was sitting on your WiFi network, so I am unable to access any other device other than your Grase Hotspot machine.
The grase-conf-openvpn package will connect your hotspot computer to a virtual private network, that allows remote access to your computer on that virtual private network. This connection is the same as if I was sitting on your WiFi network, so I am unable to access any other device other than your Grase Hotspot machine.
Install Ubuntu Server to computer. UbuntuServerInstallation (Ubuntu 12.04 (LTS) is tested and currently supported. Debian 6 is also currently supported) If you didnt follow the Ubuntu Server install instructions, or have installed a GUI, please check the Hardware Setup page for some important information about the network card setup. When it boots you will be presented with a prompt. Login with the username and password you set. Download latest grase-repo package from http://packages.grasehotspot.org /pool/main/g/grase-repo/ e.g. (Update to point to the latest grase-repo package at the above link) $ wget http://packages.grasehotspot.org/pool/main/g/grase-repo/grase- repo_1.4_all.deb install the package $ sudo dpkg -i grase-repo_1.4_all.deb Update the repository $ sudo apt-get update INSTALLATION GRASE Hotspot Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 1 sur 24 24/09/2014 21:09 Then install the components. Currently for a full system, the following command should suf- ce $ sudo apt-get install grase-www-portal grase-conf-freeradius grase- conf-squid3 grase-conf-openvpn This will proceed to download all the dependencies as well and install them. It will ask a few questions which are needed to nish setting it up. See the below sections for answering these questions If you have issues installing coova-chilli, see http://support.rstudio.org/help/kb/advanced/in- stalling-openssl-098-on-debian-7-wheezy for more information on installing libssl0.9.8 IMPORTANT: In the interest of total openness, you should be aware that the grase- conf-openvpn package will connect your Hotspot computer to a virtual private network, that allows remote access to your computer on that virtual private network. This is used for 3 purposes: If you request assistance, we have a method of connecting to your Grase hotspot machine remotely to assist you. This connection is the same as if I was sitting on your WiFi network, so I am unable to access any other device other than your Grase Hotspot machine, and I am only able to access its web interface. (This is also the reason for the support user in the web interface) Statistics gathering. Again, only the information that is publicly available on the web interface, in particular the version you are using. Used to track uptake of new versions So YOU can remotely administer your Grase Hotspot. If you need the ability to remotely login to your Grase Hotspot device, (i.e. from outside of your WiFi/Local network). If you need to do this, please contact me to arrange your side of the connection, so we ensure your computer remains secure To be clear, I DO NOT have any more access to your computer, than the admin web interface provides. If you delete the support user, the only access I have is to get the version number for Statistics gathering. Finally, if you have a support contract for full remote assistance, then install the remote assis- Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 2 sur 24 24/09/2014 21:09 tance part. (Certain organisations currently get this, if in doubt please contact me rst). Please do not install the grase-remote-assist-user unless you understand why you are installing. I have purposely made the below command break if you copy and paste it and do not understand what it is. $ sudo apt-get install grase_remote_assist_user Conguring grase-conf-freeradius Attempting to setup the database manually is possible but should not be attempted without good reason. When it asks you if you want to use dbcong-common to manage it, please answer yes. 1. You will then need to enter the MySQL root users password which was set during the Ubuntu Server install. If you didnt select LAMP when installing Ubuntu Server, before you get to this question it will install MySQL and ask you to set a password. 2. It will then ask you for and MySQL application password for grase-conf-freeradius. You can leave this blank and a random password will be created. If you are going to want/need to poke around in the user database userself with SQL commands, then set this password to something you know. 3. Conguring grase-www-portal See the above section for grase-conf-freeradius, all of that applies for this, its just for the database for the web interface (mostly admin users and logs) Install nished This should have installed the base system, and submit the systems key to a central server for remote admin. (But not the remote admin user setup, that will have to come later at this stage). You should now be able to access the web interface at http://10.1.0.1/grase/radmin (from the LAN side). The LAN side is the network interface you are running your WiFi Access Point off. Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 3 sur 24 24/09/2014 21:09 Default username is admin and password is hotspotadmin Please post support requests to the mailing list, and not as com- ments below. This way the whole community can assist with an- swering your questions. Comments are CLOSED! 67 THOUGHTS ON INSTALLATION Pingback: GRASE Hotspot Installation JUNE 2, 2011 AT 12:27 PM Mate great work Is there a way to geto the gui from the wan side cheers looking forward to updates JUNE 2, 2011 AT 2:51 PM Easiest way is to port forward port 80 to your hotspot machine (you can port forward an alternative port like 5678 as long as it points to 80 on the hotspot machine). Just make sure you secure the server to allow access from limited ip addresses. JUNE 3, 2011 AT 9:59 AM Thanks mate just had a look where is the script located i am running 11.04 and just found out its changed a bit from 10.10 marty tim marty Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 4 sur 24 24/09/2014 21:09 cheers JUNE 10, 2011 AT 7:14 PM Your Hotspot works like a charm I thank you so much for all your work. Denitely Greater than all the other free hotspot ! Youre amazing Seb OCTOBER 3, 2011 AT 3:56 AM I agree JUNE 19, 2011 AT 5:20 AM the installation, dont work. I cant install on ubuntu server 10.04 this command dont work sudo apt-get install grase-www-portal grase-conf-freeradius grase-conf-squid3 grase- conf-openvpn have any idea? Thanks JUNE 20, 2011 AT 2:47 AM Seb jose manuel davide davide Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 5 sur 24 24/09/2014 21:09 I to all, with ubuntu server 11.04 its work but i think that we have some problem with dns. JUNE 21, 2011 AT 10:58 PM Had a problem with installing as the Ubuntu 10.04 server squid version was not high enough, was generating an error with the version I found squid3 3.1.6 available on the following website, which solved my installation prob- lems https://launchpad.net/~ubuntu-backports-testers/+archive/ppa/+build/1981799 JULY 6, 2011 AT 6:20 PM Good Morning All i got this error msg while conguring Grase HotSpot Any HELP please.. Thanks * Stopping virtual private network daemon(s) * Stopping VPN grase: No such VPN is running. * Starting virtual private network daemon(s) * Starting VPNgrase [fail] invoke-rc.d: initscript openvpn, action restart failed. Setting up grase-www-portal (3.3) JULY 12, 2011 AT 8:18 PM This message is normal for the grase-conf-openvpn package. Until the VPN certicate is approved by the central server, the VPN cant start. The install is ne. Anne ifeoluwa tim THANK FOR THE REPLY Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 6 sur 24 24/09/2014 21:09 JULY 13, 2011 AT 8:18 PM Thanks Tim for the Response I will get the community on my success thanks Willing to help on Translation JULY 13, 2011 AT 8:22 PM Tim, please for how long will i have to wait for the server to approve it? Thanks in advance.. OCTOBER 14, 2011 AT 1:37 AM Hello, I installed the latest version of fat hotspot on ubuntu 11.04. but from the PC client is not possible to go on the internet. in fact, I have not even the captive portal. someone could help me? OCTOBER 17, 2011 AT 6:27 PM Hi Fabrice. Please post all support requests to the mailing list. Well need you to run different com- mands to try and diagnose where the problem is. Thanks Tim NOVEMBER 1, 2011 AT 2:28 AM works great! were conguring the login screen. i personally donate you! THANK FOR THE REPLY fabrice tim mena Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 7 sur 24 24/09/2014 21:09 NOVEMBER 1, 2011 AT 4:44 AM hi, i cant integrate the conection with a dansguardian, to lter what can users use? NOVEMBER 1, 2011 AT 4:47 AM im sorry. this is my question: could i integrate Dansguardian on the same server? NOVEMBER 3, 2011 AT 1:37 PM Hi Mena. It is possible to run Dansguardian on the same server, Ive just not written any instruc- tions for it yet. Please consider posting to the mailing list as someone else may have al- ready set it up. Tim NOVEMBER 4, 2011 AT 11:02 PM thanks NOVEMBER 10, 2011 AT 12:33 PM Hola, es factible realizar control de acceso a sitios web con grasehotspot? Puedo modi- car el archivo squid.conf para agregar las acl? Excelente herramienta grasehotspot. mena mena tim me Manuel Mendoza Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 8 sur 24 24/09/2014 21:09 Saludos. NOVEMBER 10, 2011 AT 12:59 PM Hi Manuel. Yes, you can use squid to control access. Please post support requests to the mailing list, preferably in English. NOVEMBER 10, 2011 AT 9:09 PM Hello Tim, i have seen that in squid directory there are 2 les squid.conf and squid.conf.grase which of these les is using grasehotspot? Also i dont see in the acl the network 10.1.0.x to be allowed. NOVEMBER 21, 2011 AT 3:06 AM that is what i want to do, well not exactly the same. i want to lter page by user. lo que quiero hacer es ltrar por usuario, que unos puedan acceder a varias paginas y otros no. Tim me dijo que para eso debia congurar a squid para que conozca la base de datos de los usuarios, aun no he tenido exito. this project is great Tim!! NOVEMBER 10, 2011 AT 1:44 PM dre@GRASE-HOTSPOT:~$ sudo apt-get install grase-www-portal grase-conf-freeradius grase-conf-squid3 grase-conf-openvpn Reading package lists Done tim Manuel Mendoza mena andre Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 9 sur 24 24/09/2014 21:09 Building dependency tree Reading state information Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: grase-conf-freeradius: PreDepends: coova-chilli (>= 1.2.6grase3) but it is not going to be installed grase-conf-squid3: Depends: squid3 (>= 3.1) but it is not going to be installed E: Broken packages NOVEMBER 18, 2011 AT 6:59 PM Try a newer version of Ubuntu DECEMBER 14, 2011 AT 9:39 AM Great work, once I had the correct version of ubuntu (11.04 worked for me) it came up no worries. All I was wondering was how to change the default prices for the data and time limits. DECEMBER 14, 2011 AT 9:42 AM Older versions of Ubuntu dont currently work as they dont have a new enough version of squid3. As for the default data and time limits, Im working on a x for that. Ideally, you use the groups feature to setup groups with a default data and time limit, and then just select that group. As for the prices of data and time, they are under the main settings page. Gert-Jan Jason tim Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 10 sur 24 24/09/2014 21:09 DECEMBER 28, 2011 AT 6:20 AM Thanks for the great work. Ive been trying to install on 10.04 LTS Server and was having the same issues as above. Ill try with 11.04 and see how it goes. Again, Thanks to EVERYONE! FEBRUARY 12, 2012 AT 4:29 AM Hello good work, I wanna know how can into to admin page from another pc using http://10.1.0.1/grase/radmin but no works can you help me with that please? FEBRUARY 13, 2012 AT 4:08 PM Please post support request to the mailing list. The 10.1.0.1 address will work from a computer connected to the Hotspot, as long as you dont change the default settings. If you wish to access this page from a machine on the WAN side of the Hotspot, youll need to nd out its WAN ip address and use that in place of 10.1.0.1 Tim FEBRUARY 14, 2012 AT 7:24 AM Hi tim it really works now I wanna introduce a image in the portal customisation can u help me please? FEBRUARY 14, 2012 AT 8:12 AM Hey Tim, Just wanted to say GREAT WORK! This is an awesome system, but I did have to Kyle wilson tim wilson Kyle Hoehn Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 11 sur 24 24/09/2014 21:09 do some searching to nd out that it needed Ubuntu 10.10 and also I had to write a script to auto-start chilli since there was something messed up there, but it was pretty easy to gure out. Again, GREAT WORK! Kyle FEBRUARY 25, 2012 AT 6:24 AM How to get GraseHotspot to work on ubuntu 11.01 when the two network cards are not congured well. Make sure that you have disabled DHCP, Encryption, and Router feature in your AP or router (if exist) 1. $ ifcong . to see the interfaces. 2. $ sudo gedit /etc/chilli/cong to see part of the coova chilli conguration below. # Local Network Congurations # HS_WANIF=${HS_WANIF:-eth1} # WAN Interface toward the Internet HS_LANIF=${HS_LANIF:-eth0} # Subscriber Interface for client devices 3. Modify the interfaces to suite yours. 4. Restart and voila it should be working now 5. Access your admin hotspot interface from http://10.1.0.1/grase/radmin MARCH 10, 2012 AT 4:28 AM Hi, bismark Boniface Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 12 sur 24 24/09/2014 21:09 Can grase hotspot run or installed on Ubuntu Desktop 11.10 ? someon ehelp out MARCH 10, 2012 AT 9:40 AM Yes Boniface it will work am using a desktop version myself. You just need to install some other applications for it to work. First you need to install lamp, followed by phpmyadmin then you can continue with the grase installation from their website. below is the command to install lamp and phpmyadmin # sudo apt-get install php5 mysql-server apache2 follow the instructions then # sudo apt-get install phpmyadmin then continue with installation from http://grasehotspot.org/documentation/installa- tion/ hope this was helpful APRIL 7, 2012 AT 9:05 AM Thanks Bismark. sorry for the delay in responding. i have actually been busy studying for my masters exams. i tried installing grasehotpot as per your advise and after 2days of struggling it really worked out. thanks a lot. MARCH 10, 2012 AT 9:38 AM Yes Boniface it will work am using a desktop version myself. You just need to install some other applications for it to work. Bismark Boniface Bismark Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 13 sur 24 24/09/2014 21:09 First you need to install lamp, followed by phpmyadmin then you can continue with the grase installation from their website. below is the command to install lamp and phpmyadmin # sudo apt-get install php5 mysql-server apache2 follow the instructions then # sudo apt-get install phpmyadmin then continue with installation from http://grasehotspot.org/documentation/installation/ hope this was helpful MARCH 10, 2012 AT 9:41 AM How to get GraseHotspot to work on ubuntu 11.01 when the two network cards are not congured well. MODIFIED Make sure that you have disabled DHCP, Encryption, and Router feature in your AP or router (if exist) 1. $ ifcong . to see the interfaces. 2. $ sudo gedit /etc/chilli/cong to see part of the coova chilli conguration below. # Local Network Congurations HS_WANIF=${HS_WANIF:-eth1} # WAN Interface toward the Internet HS_LANIF=${HS_LANIF:-eth0} # Subscriber Interface for client devices 3. Modify the interfaces to suite yours (i.e. HS_WANIF:-eth1 and HS_LANIF:-eth0) 4. now edit the network interfaces by ( # sudo gedit /etc/network/interfaces ) 5. add the ff line (iface eth1 inet manual ) where eth1 is the lan interface 6. Restart Chilli and the whole system. ( # sudo service chilli restart ) and ( #sudo reboot). 7. Upon restart access admin hotspot interface from http://10.1.0.1/grase/radmin 8. Clients will be automatically redirected. Bismark Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 14 sur 24 24/09/2014 21:09 MARCH 12, 2012 AT 6:54 AM Its not recommended changing the /etc/chilli/cong le. The LAN and WAN interfaces are setup semi-automatically and via the admin interface. The WAN interface (which should be plugged in while installing the packages) will be automatically detected based on the default gateway to the internet. So simply, if you have internet access while installing, which you should, it should detect the WAN inter- face correctly. If you have more than 2 NICs, then the LAN interface wont always be detected cor- rectly, but can be selected in the Admin interface. Thansk for giving assistance Bismark! MARCH 30, 2012 AT 1:34 AM i installed this software on ubuntu 11.10 and dont work perfectly !!! i create an account in the admin interface and whene i connect from client post the loin succeed but ther is no internet connection is there any specials tips for install Grase ?? thx APRIL 18, 2012 AT 2:15 PM Hi Amma I think you will need to post in the mailling list for more support on this. Also include details like Whether you installed as a Virtual machine or whether it is installed on a physical pc on its own with ubuntu and whether there is 1 or 2 network cards. how the network cards are setup and possibly a diagram of how you have it setup tim Amma Scrugio Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 15 sur 24 24/09/2014 21:09 But in short you will nd Network Eth0 = Internet Network Eth1 = Local Network or switch. There are some issues installing this package on top of a desktop client of ubuntu that you need to be aware of and this gets a little explained in the hardware setup link at top right of page. you can thank network manager for this APRIL 7, 2012 AT 9:45 AM Hi Tim, how many co-current users can grasehotspot support? APRIL 17, 2012 AT 9:18 AM This is dependant mostly on the PC running the hotspot system. If your running an old pc or slow system as ur server then con-current users will be lower than that of a more up to date system. Things to be aware of Harddrive Speed Access Speed Ram Amount available via amount used CPU processor Speed and of course the network cards 1gb network interface cards will work better than 100mb network interface cards. same applies to the rest of the network the server is implemented on with it being 100mb network or 1gb network. and so on APRIL 19, 2012 AT 6:51 PM Boniface Scrugio Boniface Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 16 sur 24 24/09/2014 21:09 thanks scrugio APRIL 23, 2012 AT 9:26 PM is there anyway to limit the speed of each user? APRIL 24, 2012 AT 1:40 AM I have installed the server and it looks great. but there is one thing i need help. some of my users are supposed to get local(internal) IP addresses while others need to get live (external) IP addresses. how can i congure that? APRIL 26, 2012 AT 10:35 PM u may need to elaborate on this a bit more but from what i get PC 1, 2, 3 need to be accessible from the wan PC 4, 5, 6 dont need to be assesable from wan but have access to wan from the lan. Could u explain the reason for this need ? is it the pc or user different, users on same pc or same user on different pcs. more details to understand the issue would be good to ar- rive at a solution. it would also be suggestive to post via the maillist to get a wider community of grase users who may also be able to help with this solution your looking for. APRIL 27, 2012 AT 12:30 AM If thats the case, you could potentially use a router running DDWRT and set up VLANs for specic ports to do what is needed there. I dont know about them being able to have a separate address, but using ACLs on the different VLANs you could Hanan Hanan Scrugio Kyle Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 17 sur 24 24/09/2014 21:09 potentially have the specic computers access network resources that way and pre- vent the other computers not have access to those resources. Just a suggestion. Im not 100% sure if that would work or not, but it might be worth a shot. APRIL 28, 2012 AT 5:01 PM Yeah this would be one way but that would be entirely dependant on the network setup that Hanan Needs. if its specic users and not pcs this would be irrelevant. then again if Hanan wants PC to go thru the hotspot system but be assessable from wan then the most likely way would be adding and editing routing and cong les to be of use. again this is entirely on what kind of network Hanan actually wants and Hanan will need to be very very clear on specically what is required. for a server behind the hotspot for example. that users do need to use. u can setup 2 network cards on it and connect one card to the lan outside the hotspot. its ac- cessable from wan but when u go to use the internet as a user it routes thru to the hotspot. any further comment really requires Hanan to be alot more specic on their network requirements. JUNE 15, 2012 AT 6:46 PM Hi everyone. Wanted to know whether grasehotspot can run on a more secure https im- plimentation on the host computer. And if it can, can somebody help me out on how to go about it? JUNE 23, 2012 AT 5:03 AM I got this below error on radmin login page | Ubuntu Server 12.04 amd64 Error Scrugio Boniface Shamikh Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 18 sur 24 24/09/2014 21:09 An Error has occured. Please report the error to the administrator There may be more information available to the administrator in the logs Getting groups failed: MDB2 Error: no such table JUNE 24, 2012 AT 10:42 AM This means more information is available in your server logs. Please post support re- quests to the mailing list. JULY 18, 2012 AT 7:56 PM Hi everyone. it has been a while since i asked this,Wanted to know whether grasehotspot can run on a more secure https implementation on the host computer. I am running a free community internet access and people are worried of their safety due to use of an open network wireless access point. I want to retain open access but ensure access of internet through grasehotspot is more secure than just using javascript aun- thentication. So i want to impliment a more secure way open SSL certicate. Tim can you can you help me out on how to go about it? Thanks JULY 19, 2012 AT 1:13 PM Please post support requests to the forum. The short answer, you are asking for the wrong thing. The login system in use is secure enough to protect a users password, as it uses CHAP authentication via Javascript. This prevents a user snifng a password over the open access point, when logging in to the portal. You can assure your users that their login details are safe. HTTPS would secure it another step, but then you need to purchase an SSL certicate that matches the domain name you are using, which requires more changes to the un- derlying system (which will come in a future version). This still only secures the login though. tim Boniface tim Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 19 sur 24 24/09/2014 21:09 What your users should actually be worried about, is everything they do over the hotspot, which isnt via a HTTPS website. i.e. if you goto http://facebook.com then ev- erything that travels between you and facebook is visible to anyone snifng the net- work. HTTPS in the Hotspot wont x this, but https://facebook.com will. There are 2 ways to x this. Both are planned for future versions. The rst is to pro- vide an OpenVPN server on the hotspot, that you can connect to once authenticated to have all your trafc encrypted over the unsecured wireless access point. This is the so- lution that will be easiest to deploy, but possibly harder for clients to setup. The second way is with WPA-EAP, which means you login to the hotspot with your login and pass- word at WPA time, without a captive portal. This is easier for clients, but harder for the setup as it requires hardware that supports it. You can assure your users that the Javascript CHAP login system is as secure as it needs to be for their login details, and that HTTPS (SSL) costs mean they would probably have to pay for their free community internet access. (Not entirely correct, but its difcult to maintain a SSL cert without paying a bit to a CA) Hope that answers your question, please direct all future requests to the mailing list. JULY 24, 2012 AT 4:08 AM thanks a lot Tim. JULY 28, 2012 AT 11:06 AM Hi, Thanks for your program. I have installed it on Ubuntu 12.04 and everything went smooth. I am trying to use your hotspot soft to authenticate users coming in to squid port on 3128. I have another program which redirects users to the squid interface. Boniface Humphrey Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 20 sur 24 24/09/2014 21:09 sherpa sherpa-proxy -b sherpa.com,3128 -f sherpa.com,8443 So trafc coming to port 8443 are directed to 3128. Is there anything I can do to make this work on the wan side? Thanks once again Cheers JULY 28, 2012 AT 11:20 AM Hi again, I could make the trafc enter through the lan side too, but my program wants to see a port number. Cannot seem to redirect it to a lan interface sherpa sherpa-proxy -b 10.1.0.1,3128 -f sherpa.com,8443 So trafc coming to front-end sherpa.com:8443 gets redirected to back-end 10.1.0.1:3128 Any suggestions? Thanks JULY 28, 2012 AT 5:10 PM Please post support requests to the mailing list JULY 28, 2012 AT 10:07 PM Thanks I did join the mailing list. By the way, is there any specic port on the Lan that this Humphrey tim Humphrey Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 21 sur 24 24/09/2014 21:09 software is listening? for example port 8080 OCTOBER 21, 2012 AT 11:42 AM IT Doesnt WORK Properly Firstly needs to be updated!!!! Version in repo is 1.4 and tutorial says 1.3 Secondly, when all installed all pages turn in error unless you manually add .php to the end of URL Could you please advise on how to FIX? Thank You OCTOBER 23, 2012 AT 11:41 AM Hey Marco. Firstly, youll note that the rst line above the copy and paste instructions says you need to update for the latest version in the repo. Its a pain to constantly be updating this page and any other page that points to the link. Secondly, the pages with .php is caused by this bug. http://bugs.debian.org/cgi-bin/bu- greport.cgi?bug=670945 It seems they have chosen to not x it how wed like it xed, and so in the next release therell be a x in the grase-conf-apache2 package (actually itll hit the repos before the next proper release) Tim Marco tim Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 22 sur 24 24/09/2014 21:09 OCTOBER 24, 2012 AT 7:43 AM Thanks Tim I did gure it out in the end, and am happily testing your beautiful software package! Its never enough to say thank you for making such easy and resourceful application! I would like to help this project in any way I can, so please let me know by email what would be the best way to contribute! I have read above that you had some issues with your computer, and hope that you now are sorted! If not, let me know if I can help!!!!!!! Regards NOVEMBER 12, 2012 AT 10:55 PM Hello, any help please? after installing the grase software, for some reason it messes up my network conguration of the ubuntu when i try to restart the server, and i do not get internet anymore on the server, also i was unable to access the setup page of the grase hardware any help appreciated thanks. NOVEMBER 13, 2012 AT 7:29 AM Tim, Finally I got it working, it works great!, great software, Will like to know if there is a way I can use Time limit per day /month instead of per minutes, is there an option where i can change it? Also, If a person can create their own account (I plan to use walled gar- den) so they can pay via paypal, so to have the option of creating their own account while i control the amount depending on how they pay. I know the php and html coding part to create the portal, however, Dont know if i need to change something on the code, or If i Marco Santiago Santiago Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 23 sur 24 24/09/2014 21:09 can do it via database or options.. I did not see anything on the settings. Please let me know, thanks Santiago NOVEMBER 13, 2012 AT 9:41 AM Please see the mailing list Pingback: Installing Grase Hotspot 3.7.7 in Ubuntu 11.10 Be Open Be the Source COMMENTS ARE CLOSED. tim Installation | GRASE Hotspot http://grasehotspot.org/documentation/installation/ 24 sur 24 24/09/2014 21:09
Kali Linux - An Ethical Hacker's Cookbook - Second Edition: Practical recipes that combine strategies, attacks, and tools for advanced penetration testing, 2nd Edition
React.js for A Beginners Guide : From Basics to Advanced - A Comprehensive Guide to Effortless Web Development for Beginners, Intermediates, and Experts
Windows Server 2019 Administration Fundamentals - Second Edition: A beginner's guide to managing and administering Windows Server environments, 2nd Edition