Documente Academic
Documente Profesional
Documente Cultură
Lightweight
Hard wearing
Flexible
Excellent adhesion to steel and concrete substrates
Non-slip - excellent grip even when wet
Chemically resistant
Prevents aquaplaning
Waterproof
Zero spread of flame
Design criteria
The thickness of the Cicol ET Slurry is varied to suit
traffic conditions as shown in the table below.
Traffic density
Thickness
Light
Medium:
Heavy:
3.0-3.5 mm
3.5-4.0 mm
4.0-4.75
Zise
(mm)
0.4 to 1.0
1.0 to 3.0
3.0 to 5.0
Standards compliance
Properties
Description
Chemical resistance:
Light
traffic
*
*
.
Medium
traffic
*
*
*
Heavy
traffic
.
.
*
30 mins
1.6
Foot traffic after 24 hours,
vehicular traffic after 48 hours
Fully cured Cicol ET Slurry has
been shown to be resistant to
the following chemicals after
continuous immersion for 12
months at 20oC.
Petrol
De-icing salts
Kerosen
Diesel
Hydraulic fluid Aircraft fuel
Dilute mineral 10 % area in
Acid etch
water
Application instructions
Surface preparation
Cicol ET Slurry can be applied to a variety of substrates.
As with all flooring materials or protective coatings,
correct surface preparation is essential.
Steel substrates
Cicol ET Slurry is specially formulated to exhibit
tenacious adhesion to unprimed steel. However, all
steel substrates should be blast cleaned to a minimum
Sa21/2 standard of cleanliness. An angular profile
amptitude of at least 75 microns is recommended. The
slurry should be applied as quickly as possible to the
blasted steel surface. If the standard of the surface falls
below Sa21/2 then the steel must be reblasted.
Concrete substrates
Cicol ET Slurry is applied to clean, sound, dry concrete
substrates which are free of any laitance or loose
particles. Mechanical scarifying or blasting methods are
strongly recommended. Prepared concrete substrates
should be primed with Nitoprime 25 which is applied by
lambswool roller to provide a thin even coverage. Avoid
over application and puddles. Cicol ET Slurry is
applied onto the Nitoprime 25 as soon as it is free from
surface tack.
Asphalt substrates
Cicol ET Slurry can be applied onto asphalt substrates
providing they are clean, sound and dry. It is also
recommended that the asphalt should be at least 3
months old. The asphalt should be lightly grit blasted to
remove any weakly bonded or contaminated material to
provide the desired surface. No primer is required on
asphalt.
Wooden substrates
Cicol ET Slurry can be applied directly onto clean, dry
timber substrates.
Aluminium substrates
Must be sweep blasted and degreased if necessary
using Fosroc Solvent 102 to provide a sound
mechanical key. Cicol ET Slurry can be applied directly
to the prepared substrate.
Mixing
Mix the two liquid components (A and B) thoroughly
using a forced action mixer such as a cretangle or
zyklos. Add the mineral fillers and mix until a
homogeneous slurry consistency is formed. The total
mixing operation should take about 5-7 minutes. The
Cicol ET Slurry is now ready for use. Do not add
thinners or solvent.
Laying
Once mixed the Cicol ET Slurry must be used within
the specified pot life.
Storage
o
33 C
above 50oC
above 50oC
35oC
Shelf life
All products have a shelf life of 12 months if kept in a dry
store in the original, unopened packs.
Estimating
Storage conditions
Supply
Cicol ET Slurry is supplied in 30 kg packs. Nitoprime 25
is supplied in 1 kg and 5 kg packs.
Net (kg/m2)
8.0
10.0
16.0
.
Jeddah Showroom
Dammam
Yanbu
Medinah
Head Office & Factory
Important note: Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of
sale, copies of which may be obtained on request. Whist Fosroc endeavors to insure that any advice, recommendation, specification or information it may give
is accurate and correct, it cannot, because it has no direct or continuous control over where how its products are applied, accept any liability either directly or
indirectly arising from the use of its products, whether or not in accordance with any advice, specification, recommendation or information given by it
ME/22008/95/A