Documente Academic
Documente Profesional
Documente Cultură
Device Management
Titlepae
Notice
(2) Used or copied for use in a backup computer if any computer for which
it was acquired is inoperative;
SPECTRUM, the SPECTRUM IMT/VNM logo, DCM, IMT, and VNM are registered
trademarks, and SpectroGRAPH, SpectroSERVER, Inductive Modeling
Technology, Device Communications Manager, and Virtual Network Machine
are trademarks of Aprisma or its affiliates.
Virus Disclaimer
Aprisma makes no representations or warranties to the effect that the Licensed
Software is virus-free.
Aprisma has tested its software with current virus checking technologies. However,
because no anti-virus system is 100% reliable, we strongly caution you to write
protect and then verify that the Licensed Software, prior to installing it, is virus-free
with an anti-virus system in which you have confidence.
Page 2
(d) Any other rights or limitations regarding the use, duplication, or disclosure
of this computer software are to be expressly stated in, or incorporated in,
the contract.
(e) This Notice shall be marked on any reproduction of this computer software, in
whole or in part.
Contents
INTRODUCTION
PERFORMANCE VIEWS
12
8
Application Information (examine) ........................8
Computer Telephony Interfaces (configure) .........8
Device Connections (configure) ...........................8
Device (configure) ................................................8
Device Performance (monitor) .............................8
Interfaces (enable/disable) ...................................8
Line Interface Modules (examine/configure) ........8
Model Information (examine)................................8
Model Redundancy (configure) ............................8
ISDN Basic Rate Extensions (monitoring)............8
Interfaces (examine).............................................8
MD110 Alarms (monitor) ......................................9
Port Configuration (examine/modify) ....................9
Port Statistics (monitor) ........................................9
Radio Exchange Information (examine) ...............9
Port Connections (resolve) ...................................9
Interface Thresholds (configure) ..........................9
Interface Address Information (examine) .............9
10
15
20
Application Icons........................................................... 21
Supported Applications ................................................. 21
Page 3
Contents
CONFIGURATION VIEWS
Contents
22
38
INDEX
39
Page 4
Introduction
This section introduces the SPECTRUM Device Management documentation for the Ericsson MD110 PBX
device.
Required Reading
To use this documentation effectively, you must
be familiar with the information covered by these
other SPECTRUM online documentation topics:
Page 5
Introduction
Supported Device
Supported Device
network can consist of on-premise hardwired, wireless nodes, or wide area networked
links
can provide cordless communication for all
users in an office environment, independent
of the size of the organization
Model Name
MD110_PBX
Page 6
Model Name
MD110_PBX
Introduction
Sales_Nashua
LAN 802.3
Device Icon
JK2
MD110 PBX
WA_Link
Admin_Nashua
LAN 802.3
Page 7
Tasks
This section lists device management tasks alphabetically and provides links to descriptions of the views and/or
tables used to perform the task.
Device (configure)
Interfaces (examine)
Device Views on Page 12
Performance Views on Page 10
Interface Icon Subviews Menu Options on
Page 18
Interfaces (enable/disable)
Admin Status on Page 37
Page 8
Tasks
Page 9
Performance Views
This section describes the Performance views available for models of the MD110 device in SPECTRUM.
% Transmitted
% Error
% Discarded
The view also provides button access to the SNMP
Agent Detail view, which shows pie charts with
error breakdown statistics.
System Up Time
Network Address
Name
Contact
Description
Location
Manufacturer
Device Type
Primary Application IP2Ap
Log
Value
Serial Number
Average
Peak Value
*Frame Rate
% Received
0.10
0.01
%Transmitted
%Error
%Discarded
0
0:40:0 0:30:0 0:20:0
Graph Properties
Scroll to Date-Time
Detail
123.45 of Type...
Page 10
Performance Views
Load
* Packet Rate
% Error
% Discarded
Page 11
Device Views
This section describes the Device view and subviews available for models of the MD110 device in SPECTRUM.
Device View
Model Name
Contact
Network Address
Description
Primary Application
Location
Help
Page 12
System Up Time
Manufacturer
Device Type
Serial Number
Ericsson
MD110
OK
normal
1 UP
56 UP LIM-56
111
UP LIM-111
123.45 of type...
Device Views
Device View
Module Icons
Ericsson
MD110
Module Type
Agent Status
MD110 Alarm Status
OK
normal
1 UP
56 UP LIM-56
111
UP LIM-111
Port Number
LIM Descriptor
Page 13
Device Views
Table 1:
Selection
Notes
Device View
Route/Trunk
Information
Interfaces
Information
Configuration
LIM
Information
Menu Option
Notes
Port Notes
LIM Detail
Page 14
Page 15
Interface Icons
123.45
MD110 PBX
(b)
1 ON
ethernet
Model Type
(g)
Model Type
SX-16Ethernet
0:0:30:68:6F:1B
123.45.67.89
0
1
ON
(c)
(d)
(e)
(f)
IF Status Label
IP Address Label
Gauge Label
ethernet
INTEL82596SX16
0:8:63:5:BA:6A
123.45.67.89
123.45 of type...
Page 16
Label
Text
Green
ON
ON
ON
Blue
OFF
OFF
OFF
Yellow
OFF
ON
OFF
Red
Testing
Test
Test
Page 17
Table 4:
Menu Option
Opens the...
Operational Status
The current state of the interface (ON, OFF, or
Testing).
Performance
Detail
IF Status
IF Configuration
AT IF Address
Translation Table
Secondary Address
Panel
Thresholds
Model Information
Administrative Status
This button allows you to select the desired
operational state of the interface (ON, OFF, or
Testing).
Page 18
Load Threshold
Allows you to set the values to determine the
point at which the percent load will generate an
alarm (on) and the point at which it will shut the
alarm off (off).
Packet Rate Threshold
Allows you to set the values to determine the
point at which the packet rate will generate an
alarm (on) and the point at which it will shut the
alarm off (off).
Error Rate Threshold
Allows you to set the values to determine the
point at which the error rate will generate an
alarm (on) and the point at which it will shut the
alarm off (off).
% Discarded Threshold
Allows you to set the values to determine the
point at which the percent of discarded packets
will generate an alarm (on) and the point at which
it will shut the alarm off (off).
Page 19
Application View
This section describes the Application view and the associated application-specific subviews available for the
MD110 in SPECTRUM.
System Up Time
Network Address
Manufacturer
Contact
Device Type
Description
Location
Primary Application
Serial Number
123.45
md110
MD110 PBX
MIB-II
MD110
SNMP
md110
SNMP2_Agent
ICMP
ICMP
ICMP_App
IP
IP2_App
IP2_App
System
System
System2_App
123.UDP
UDP_2
UDP_2App
123.45 of Type...
Page 20
Application View
Application Icons
Application Icons
Supported Applications
Application
Table 5:
md110App
Reference
IP Routing (IP2_App)
Routing Applications
MIB-II (SNMP2_Agent)
MIB-II Applications
Standard RMON
(RMONApp)
Standard RMON
md110App
(c)
a
Page 21
Configuration Views
This section describes various Configuration views and subviews for models of MD110 devices in SPECTRUM.
Help
Model Name
System Up Time
Network Address
Manufacturer
Contact
Device Type
Description
Location
Primary Application
Serial Number
Interfaces Information
Agent State OK
Alarm Information
LIM Information
Group Switch Information
Agent Information
123.45 as Type...
Page 22
Configuration Views
Table 6:
Connection
State
OK
linkdown
updating
MIB
agentFault
Agent State
The state of the connection between the MD110
and the agent. The values are described in
Table 6.
Alarm Status
The current alarm status of the MD 110 node.
The alarm states and definitions are listed in
Page 23
Configuration Views
Table 7.
Alarm Information
Table 7:
Alarm State
Definitions
Critical
Major
Minor
Warning
Interfaces Information
Page 24
Configuration Views
Status
The operational state of the interface. The
possible states are described in Table 8.
Table 8:
States
Up
Down
Index
A unique value for each interface. Values ranging
between 1 and 8 show interface index and name
information; values between 10 and the
maximum interface value are a composite of the
interface index, name, description, status and
alarm class.
Interface Name
The type of interface (i.e., Ethernet, FDDI,
Loopback, etc).
Description
A textual string containing information about the
interface. This may include endpoint or server
information.
Alarm Class
Displays active external alarm error codes. Alarm
classes range from critical (A4) to normal (A0).
ICU Information
Page 25
Configuration Views
OPI Information
Server Information
CIL Information
Data Extns Information
CTI Information
ISDN SO Information
VCU Information
Page 26
Configuration Views
Name
The name of this interface.
IF Index
A unique value for each network port.
Description
A textual description of this interface.
Port ID
Port identity for this interface type.
Status
The current operational status of this interface.
Equip Position
The equipment position for this port.
Port ID
The port identity for this interface type.
Application
The application using the ICU port.
EquPos
The equipment position for the port interface,
within the chassis or device.
Application
The application using this port. The ICP and
Server E1/T1 ELU7 interface information views
display this field.
IF Index
A unique value for each OPI port.
Port ID
The port identity for this interface type.
Equip Position
The equipment position for this port.
OPI Type
The type of OPI port.
Page 27
Configuration Views
IF Index
A unique value for each network interface
appears in each column of the Computer
Telephony Interface table.
IF Index
A unique value for each network interface. Each
value is indexed to the Call Information Logging
interface table.
Port ID
The port identity for this interface type.
Port ID
The port identity for this interface type CIL
id (SI-x).
Equip Position
The equipment position for this port.
Equip Position
The equipment position for this port.
Page 28
Configuration Views
IF Index
A unique value for each network interface of an
ISDN S0 port.
Mode
The compression mode used for this VCU board.
Port ID
The port identity for this interface type directory
number for the ISDN S0 port.
Equip Position
The equipment position for this port.
IF Index
A unique value for each network interface of a
server interface.
Port ID
The port identity for this interface type directory
number for a Server Interface.
Equip Position
The equipment position for this port.
Application
The application using the Server port.
Equip Position
The equipment position for this board.
Config
The configuration of this board.
Page 29
Configuration Views
Neighbor Address
The IP address of the nearest neighbor.
Neighbor Name
The product name for the nearest neighbor.
IF Index
A unique value for each interface.
Port ID
Identity for this interface type.
Equip Position
The equipment position for this interface.
Ex Number
The radio exchange identifier.
Equip Position
The equipment position or location of the
corresponding base station.
Status
The status of each corresponding base station.
IF Name
The name of this interface.
SPECTRUM Enterprise Manager
Page 30
Configuration Views
Alarm Text
The textual description associated with the
external alarm code.
Alarm Status
The current alarm status of the MD 110 node.
Refer to Table 7, MD110 Alarm States, on Page 24
for a list of alarm conditions.
Error Code
The error code associated with the external
alarm, which corresponds to the CODE
parameter within the ALEXP printout.
Alarm State
Indicates if the external alarm is active or passive.
Alarm Text
The textual description associated with the
external alarm code.
Error Code
The error code for this MD110 alarm.
Number Active
The number of active alarms for the MD110.
Alarm Class
Provides an indication of the severity, or warning,
of the trap notification in a network elementspecific notation. The warning alarm classes are
A4 - critical, A3 - major, A2 - minor, and A1 SPECTRUM Enterprise Manager
Page 31
Configuration Views
Code
Shows the agent alarm port pin number.
Trap Destination
Polarity
Interprets the pin signal as active or passive
alarm or else unused.
Class A
Indication of the severity of the trap notification in
a network element specific notation.
Descr-Active
Indicates alarm source and recommendation of
action.
Descr-Passive
Indicates ceasing alarm.
PIN Alarms
This table shows pin alarm identifying
information for the port.
Index
Index of the pin in the alarm port.
Alarm Text
Textual description associated with the pin alarm.
Page 32
Configuration Views
Alarm State
Indicates if the pin alarm is active or passive,
Otherwise, the pin is not configured.
Alarm Class
Indicates alarm class for this pin.
Equip Position
The equipment position for the port, which
corresponds to the MML parameter EQU.
IP Address
The IP address to which this trap is being sent.
Route Endpoints
Sequence
The sequential order in which this trap is being
sent.
Trunk Endpoints
The Trunk Endpoints Table identifies trunk
endpoints by blocktype and position.
IF Index
A unique value for each network interface of a
trunk endpoint. These values are the similar
SPECTRUM Enterprise Manager
Number
The identification number for the route.
Corresponds to the MML parameter.
Type
This route-type corresponds to the MML
parameter RO SERV-D3.
Bearer Cap
The capacity for bearer channels for a route
endpoint or a trunk endpoint.
Page 33
Configuration Views
Signalling
The type of signalling diagram for the route.
Corresponds to the MML parameter RO SIG-D11.
Status
Shows the operational status of the LIM. The
status values are up or down.
Route.IF
The trunk endpoint If index.
Endpoints
The number of bearer channels for a route
endpoint or a trunk endpoint.
GS Active Side
The active side of a group Switch. Values,
depending upon the current active side, are
side0 or side1.
Number
If this I/O (input/output) LIM shows a value of 1,
the value reflects the only LIM present.
SPECTRUM Enterprise Manager
Location
The physical location of the LIM.
Page 34
Configuration Views
Index
The index to the Group Switch table. The values
start at 1.
Status-Side0
The operational state of the group Switch
(side0).
Status-Side1
The operational state of the group Switch
(side0).
Serial Number
The agent board serial number programmed at
manufacturing time.
Index
Shows the sequence number for the group switch
links.
Equip Position
The equipment position in the LIM for the group
switch link.
Application Version
The application version stored in flash memory.
Mult Position
If multiple group switch links exist, the total
number of links appear in this column.
Page 35
Configuration Views
Agent State
Displays the state of the connection between the
agent and MD110. Values are listed in Table 9.
Table 9:
Connection
State
Last Change
Displays the date and time the view state of the
port was changed.
Description
OK
IP Network Mask
Displays the IP address and network mask for
this device.
linkDown
Phy Address
The (MAC) address of the port.
Bandwidth
The amount of bandwidth being utilized by this
port.
Packet Size
The size of the packet being passed on this port.
Page 36
Configuration Views
Help
Network Address
System Up Time
Manufacturer
Contact
Device Type
Description
Location
Primary Application
Primary Address
Preferred Addresses
Serial Number
Number of Interfaces 24
Find
Update
Index Description Type Bandwidth Physical Address Operation Status Admin Status Last Change Queue Le
0
1120049
Fast Ethernet ETH 1000000 0.40.27.7.
down
up
1
123.45 of Type...
Page 37
Network Address
System Up Time
Manufacturer
Contact
Description
Primary Application
Location
Device Type
Serial Number
Primary Address
General Information
Communication Information
MM Name
DCM TimeOut
MM Part Number
DCM Retry
MM Version Number
Community Name
Model Type
Mgmnt Protocol
Poll/Log Information
Poll Interval
Polling Status
Last Successful Poll
Log Ratio
LOGGED
POLLED
Page 38
Index
Symbols
% Discarded Threshold 19
Bandwidth 36
bearer channels 34
Descr-Active 32
Descr-Passive 32
Device Configuration View
Contact Status 23
Number of Interfaces 23, 24
Device icon 6, 20
Device Performance View 10
Numerics
1000Base-SX and 1000Base-LX 6
A
Active Alarms Table 31
Address
MAC 36
Address Translation table 18
Admin Status 37
Administrative Status 18
agent alarm port 32
Agent Board Hardware Vs 35
agent board serial number 35
Agent State 31
agentFault 23
Alarm Class 31
alarm class 33
alarm states 24
Application
Icons 20
MIB-II (SNMP2_Agent) 21
Application View 20
C
Call Logging Interface data 28
ceasing alarm 32
Chassis Device View 12
Chassis Views 20
Class A 32
Cold Start Initiate 36
Colors
Interface Status Label 17
compression mode 29
Condition Status Label 21
Configuration View
Interface
Admin Status 37
Bandwidth 36
Last Change 36
Operation Status 37
Packet Size 36
Physical Address 36
Critical 24
E
E1/T1 ELU-7 interface 29
Enable/Disable
Ethernet Port (Admin Status) 37
enable/disable redundancy 36
Equip Position 27
EquPos 27
Error Code 31
Error Rate Threshold 19
F
flash memory 35
G
group switch link 34
GS Active Side 34
Page 39
Index
I
Icon
Application 21
Icon mode 20
Icon Subviews Menu
Interface Label 14
Icon Subviews Menus
for Interface icon 18
Icons
Device 6, 20
Interface 15, 16
Indeterminate 24
Interface Adddress Translation
Table 24
Interface icon 16
Interface Icon Subviews Menu
Options 18
Interface Index 19
Interface Menu Selection
IF Details 14
IF Performance 14, 18
Interface Names Table 25
Interface Status View 18
Administrative Status 18
Operational Status 18
internal fault 23
ISDN S0 port 29
L
Labels
Index
Application Icon
Condition Status 21
Model Name 21
Model Type 21
Interface
IF Status Label 17
Interface Number Label 17
Interface Type Label 17
Physical Address Label 17
Module
Module Type 13
Slot Number 13
Port
Port Number 14
Port Status 14
Last Change 36
LIM Detail view 14
LIM information 34
LIM Table 24
linkdown 23
List mode 20
Load Threshold 19
Logical
Repeater
Menu Selections 36
Module
Details 36
N
Neighbor Address 30
Neighbor Name 30
Network I/O ports 15
Normal 24
notPresent 34
Number Active 31
M
Major 24
major applications 20
manager-defined release
number 23
MD110 BC 8 firmware 28
Minor 24
minor applications 20
MML parameter EQU 33
MML parameter RO TYPE 33
Mode 29
Mode (Icon or List) 20
Model Information View 38
Model Information views 38
Model type 6
Model Type Label 21
modeled device connections 15
Module Icon Subviews Menu 13
Module Notes 14
multiple group switch links 35
Page 40
Operation Status 37
Operational Status 18
OPI Information Table 27
Ericsson MD110 PBX
Index
P
Packet Rate Threshold 19
Packet Size 36
Performance View 10
Performance views 10
Phy Address 36
pin alarm 32
PIN Alarm Information 32
PIN Polling Interval 32
Polarity 32
Port
bandwidth 36
MAC Address 36
off 37
on 37
Physical Address 36
Port ID 27
Port Label Icon Subviews Menu 14
protocol stack 19
Index
SM-CSI1064 5
SSR_ChassApp 21
state of the connection 23
Status-Side0 35
Status-Side1 35
switch board attendant 27
W
Warning 24
T
T1 Block Type 33
Tasks 8
Threshold
%Discarded 19
Error Rate 19
Load 19
Packet Rate 19
Topology view 7
Trademarks 2
Trap Destination 32
Trunk Endpoints Table 33
Required Reading 5
Restricted Rights Notice 2
Route Information 24
updating MIB 23
Views
Application 20
Configuration 22
Interface Status 18
Model Information 38
Performance 10
Topology 7
Page 41