Documente Academic
Documente Profesional
Documente Cultură
Revision 09/13/11
2003-07
Honda Accord
TM
IMPORTANT
Before starting, compare items on your invoice with items received.
Carefully check through packaging material. If any item is missing,
please call Crutchfield Technical Support at 1-800-955-9094.
Inside...
*0000220008*
Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without warranties or
guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle production. Any person or
entity using this information does so at his or its own risk. If you find our instructions are different from your vehicle, or if you have questions, do not
continue with your installation. Contact our toll-free Technical Support at 1-800-955-9094 for assistance .
Page
2-4
Receiver Installation
6-7
Door Speakers
8-9
10
Rear Speakers
11
(coupe)
(sedan)
Phillips
Screwdriver
Panel Tool
Wire Stripper/
Crimp Tool
Crimp Caps
8mm Socket,
Ratchet &
Extension
Tools Required
022 0008
FIGURE 2
IMPORTANT
If only installing an OEM interface, complete radio removal is not necessary unless the
vehicle is equipped with navigation. Stop with the completion of step 7 where the
wiring harness can be accessed. Follow all steps if the vehicle is equipped with
navigation or installing an aftermarket radio.
FIGURE 3
FIGURE 4
5. Open pocket door. Pry out pocket to remove (Figure 3). Remove
two (2) phillips screws from cavity exposed by removal of pocket
(Figure 4).
FIGURE 1
Gear Shift Trimpanel
1-800-955-9094
TECHNICAL SUPPORT
022 0008
FIGURE 6
FIGURE 7
Storage Compartment
FIGURE 5
Lighter/Power Supply Assembl
Assemblyy
FIGURE 8
1-800-955-9094
TECHNICAL SUPPORT
022 0008
FIGURE 11
FIGURE 9
FIGURE 12
Vent Trimpanel
FIGURE 10
R
R
1-800-955-9094
TECHNICAL SUPPORT
022 0008
NOTES:
Receiver Installation
Note: Two installation kits are available for this vehicle from Crutchfield.
One kit has fully integrated temperature controls. The other kit (with
pocket) is for a standard DIN unit and does not include temperature
controls. If using this kit, the factory radio will remain in the dash.
The instructions below are for the standard/pocket kit. If installing the
integrated kit, please follow instructions supplied with the kit.
FIGURE 2
1. Match all wires by function, individually taping off wires that do not have
a match. Connect the wiring adaptor (supplied with the installation kit)
to the receiver. Note: Refer to information on the wiring adaptor package and in your receiver manual. Make final wiring connections following instructions on page 11. When completed, return to this page and
continue with step 2.
Securing Tabs
FIGURE 3
DIN Sleeve
Receiver Assembly
FIGURE 1
1-800-955-9094
TECHNICAL SUPPORT
R
022 0008
NOTES:
IMPORTANT
FIGURE 1
Sail Panel
FIGURE 3
FIGURE 2
Screw Cover
1-800-955-9094
TECHNICAL SUPPORT
022 0008
FIGURE 6
FIGURE 7
Clip
FIGURE 4
FIGURE 5
!
Door Release Cable
!
1-800-955-9094
TECHNICAL SUPPORT
CAUTION:
SAFETY CHECK
022 0008
NOTES:
IMPORTANT
FIGURE 1
FIGURE 2
Screw Cover
Sail Panel
FIGURE 3
FIGURE 5
FIGURE 4
Screw Cover in
Door Pull Cup
1-800-955-9094
TECHNICAL SUPPORT
022 0008
FIGURE 7
Clip
FIGURE 8
FIGURE 6
SAFETY CHECK
CAUTION:
R
1-800-955-9094
TECHNICAL SUPPORT
022 0008
NOTES:
FIGURE 2
FIGURE 1
Speaker Grille
1-800-955-9094
TECHNICAL SUPPORT
10
022 0008
These methods can be used to make wiring connections if no receiver or speaker wiring adaptor is available.
SOLDER METHOD
1. Carefully strip out a 1/2
section on each factory
speaker wire behind the
factory speaker harness.
Factory Wires
Negative Wires
New Wires
---
Positive Wires
Factory Wire
-- - ------
+ + + + + + + + + + + +
First
-- - --------
Last
+
+ + + + + + + + + + + + + + + + + + + +
1-800-955-9094
TECHNICAL SUPPORT
11