Documente Academic
Documente Profesional
Documente Cultură
SolidWorks
Open SolidWorks
SolidWorks
Choose Part
Go to insert>reference geometry>axis
SolidWorks
SolidWorks
SolidWorks
SolidWorks
SolidWorks
Use Smart Dimension to give the following lines the dimensions shown below
SolidWorks
SolidWorks
10
SolidWorks
11
SolidWorks
Now select this point and move it till it is parallel to the line above
12
SolidWorks
13
SolidWorks
14
SolidWorks
Now use the Tool mirror entities and chose the following lines
15
SolidWorks
Use the building line in the field Mirror about and press OK
16
SolidWorks
17
SolidWorks
Now choose the Right Plane, select Sketch and select Section View
18
SolidWorks
19
SolidWorks
20
SolidWorks
Then, you have to go to the features, click on revolved boss/base and choose the indicated
axis. Also you should quit the mark on merge result, and check to accept changes.
21
SolidWorks
22
SolidWorks
Click on features, choose fillet. In items to fillet, you should type 50 and mark the following
sections:
23
SolidWorks
24
SolidWorks
Draw a centerline.
25
SolidWorks
Using line, draw the following sketch and with smart dimensions, give it the following dimensions:
26
SolidWorks
Later, choose mirror entities. In entities to mirror select the lines which are indicated with
the red arrows, and in mirror about mark the line which is indicated with the green arrow. Check
to accept changes.
27
SolidWorks
Now, you have to go to features and click on extruded cut. Also, in direction 1 choose through
all, feature scope uncheck Auto-select, select the shown part in green and check accept.
28
SolidWorks
Next, click on fillet option. In items to fillet, you should type 40 and mark the shown edge
in yellow.
29
SolidWorks
Then, click on fillet option again. In items to fillet, you should type 15 and mark the shown
edge in yellow.
30
SolidWorks
In features to pattern choose the indicated fillets in blue, in parameters select axis 3 and in
number of instances type 5, and check to accept.
31
SolidWorks
32
SolidWorks
Using line, draw the following sketch and with smart dimensions, give it the following dimensions:
Now, choose mirror entities. In entities to mirror select the line which is indicated with the
red arrows, and in mirror about mark the line which is indicated with the green arrow. Check
to accept changes.
33
SolidWorks
You have to go to features and click on extruded cut. Also, in direction 1 choose through all,
feature scope uncheck Auto-select, select the shown part in green and check accept.
34
SolidWorks
Click on fillet. In items to fillet, you should type 15 and mark the shown edge in yellow.
Now, choose linear pattern, option circular pattern. In features to pattern choose the indicated fillets in blue, in parameters select axis 3 and in number of instances type 5, and check to
accept.
35
SolidWorks
Select offset entities. In offset distance, type 7 and select the shown edge, right click and
choose the option select tangency.
36
SolidWorks
Select offset entities again. In offset distance, type 5 and select the shown edge, right click
and choose the option select tangency. Click on reverse and check to accept.
37
SolidWorks
Then, select all those entities and click on linear sketch pattern, option circular sketch pattern.
38
SolidWorks
39
SolidWorks
Later, click on trim entities. With power trim cut the selected lines around the rim and check
to accept.
40
SolidWorks
41
SolidWorks
Go
to insert: features: move copy
42
SolidWorks
43
SolidWorks
Do it again
44
SolidWorks
45
SolidWorks
46
SolidWorks
Go
to insert: cut: with surface
47
SolidWorks
48
SolidWorks
49
SolidWorks
50
SolidWorks
51
SolidWorks
52
SolidWorks
Select chamfer
53
SolidWorks
Draw a centerline
54
SolidWorks
55
SolidWorks
56
SolidWorks
Go to circular pattern
57
SolidWorks
58