Documente Academic
Documente Profesional
Documente Cultură
Revision 1.1
March 2007
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS
OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING
TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for
use in medical, life saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for
future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
This document contains information on products in the design phase of development. Do not finalize a design with this information. Revised information
will be published when the product is available. Verify with your local sales office that you have the latest datasheet before finalizing a design.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Hyper-Threading Technology requires a computer system with an Intel® Pentium® 4 processor supporting HT Technology and a Hyper-Threading
Technology enabled chipset, BIOS and operating system. Performance will vary depending on the specific hardware and software you use. See <http://
www.intel.com/info/hyperthreading> for more information including details on which processors support HT Technology
Intel, Celeron, Intel NetBurst, Xeon and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United
States and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2007, Intel Corporation.
*Other names and brands may be claimed as the property of others.
2
Contents
1 Introduction ............................................................................................................ 11
1.1 Reference Documentation................................................................................... 11
1.2 Terminology ..................................................................................................... 12
2 Platform Configurations........................................................................................... 15
2.1 Digital Home and Digital Office Platform Configurations - RECOMMENDED ................. 15
3 Electrical ................................................................................................................. 21
3.1 AC Input - REQUIRED ........................................................................................ 21
3.1.1 Input Over Current Protection - REQUIRED ................................................ 21
3.1.2 Inrush Current - REQUIRED ..................................................................... 21
3.1.3 Input Under Voltage - REQUIRED ............................................................. 21
3.2 DC Output - REQUIRED ...................................................................................... 22
3.2.1 DC Voltage Regulation ............................................................................ 22
3.2.2 Output Transient Response - REQUIRED .................................................... 22
3.2.3 Remote Sensing - REQUIRED ................................................................... 23
3.2.4 Other Low Power System Requirements - RECOMMENDED ........................... 23
3.2.5 Output Ripple Noise - REQUIRED .............................................................. 23
3.2.6 Capacitive Load - REQUIRED.................................................................... 24
3.2.7 Closed Loop Stability - REQUIRED ............................................................ 24
3.2.8 +5 VDC / +3.3 VDC Power Sequencing - REQUIRED ................................... 24
3.2.9 Voltage Hold-up Time - REQUIRED ........................................................... 25
3.3 Timing, Housekeeping and Control - REQUIRED..................................................... 25
3.3.1 PWR_OK ............................................................................................... 25
3.3.2 Power-up Cross Loading Condition ............................................................ 26
3.3.3 PS_ON#................................................................................................ 26
3.3.4 +5 VSB................................................................................................. 27
3.3.5 Power-on Time....................................................................................... 27
3.3.6 Rise Time .............................................................................................. 27
3.3.7 Overshoot at Turn-on / Turn-off ............................................................... 28
3.4 Reset after Shutdown ........................................................................................ 28
3.4.1 +5 VSB at Power-down ........................................................................... 28
3.5 Output Protection - REQUIRED ............................................................................ 28
3.5.1 Over Voltage Protection........................................................................... 28
3.5.2 Short Circuit Protection ........................................................................... 28
3.5.3 No-load Situation ................................................................................... 29
3.5.4 Over Current Protection .......................................................................... 29
3.5.5 Over Temperature Protection ................................................................... 29
3.5.6 Output Bypass ....................................................................................... 29
3.5.7 Separate Current Limit for 12V2 - RECOMMENDED...................................... 29
3.5.8 Overall Power Supply Efficiency and ENERGY STAR ..................................... 29
4 Mechanical .............................................................................................................. 33
4.1 Labeling and Marking - RECOMMENDED................................................................ 33
4.2 Connectors - REQUIRED ..................................................................................... 33
4.2.1 AC Connector ........................................................................................ 33
4.2.2 DC Connectors ....................................................................................... 33
4.2.2.1 Main Power Connector ............................................................... 34
4.2.2.2 Peripheral Connectors................................................................ 35
4.2.2.3 Floppy Drive Connector.............................................................. 35
4.2.2.4 +12 V Power Connector ............................................................. 36
4.2.2.5 Serial ATA* Power Connectors .................................................... 36
4.3 Airflow and Fans - RECOMMENDED ...................................................................... 37
3
4.3.1 Fan Location and Direction .......................................................................37
4.3.2 Fan Size and Speed ................................................................................37
4.3.3 Venting .................................................................................................38
5 Acoustics .................................................................................................................39
5.1 Acoustics - RECOMMENDED.................................................................................39
6 Environmental .........................................................................................................41
6.1 Temperature - RECOMMENDED............................................................................41
6.1.1 Thermal Shock (Shipping)........................................................................41
6.2 Humidity - RECOMMENDED .................................................................................41
6.3 Altitude - RECOMMENDED ...................................................................................41
6.4 Mechanical Shock - RECOMMENDED .....................................................................41
6.5 Random Vibration - RECOMMENDED.....................................................................41
7 Electromagnetic Compatibility .................................................................................43
7.1 Emissions - REQUIRED .......................................................................................43
7.2 Immunity - REQUIRED .......................................................................................43
7.3 Input Line Current Harmonic Content - OPTIONAL ..................................................43
7.4 Magnetic Leakage Fields - REQUIRED ...................................................................44
7.5 Voltage Fluctuations and Flicker - REQUIRED .........................................................44
8 Safety ......................................................................................................................45
8.1 North America - REQUIRED .................................................................................45
8.2 International - REQUIRED ...................................................................................45
8.3 Proscribed Materials ...........................................................................................46
8.4 Catastrophic Failure Protection - REQUIRED ..........................................................46
9 Reliability ................................................................................................................47
9.1 Reliability - RECOMMENDED ................................................................................47
10 CFX12V Specific Guidelines 1.4 ................................................................................49
10.1 Typical Power Distribution - RECOMMENDED..........................................................49
10.2 Physical Dimensions - REQUIRED .........................................................................53
11 LFX12V Specific Guidelines 1.2 ................................................................................55
11.1 Typical Power Distribution - RECOMMENDED..........................................................55
11.2 Physical Dimensions - REQUIRED .........................................................................58
12 ATX12V Specific Guidelines 2.3 ................................................................................63
12.1 Typical Power Distribution - RECOMMENDED..........................................................63
12.2 Physical Dimensions - REQUIRED .........................................................................72
13 SFX12V Specific Guidelines 3.2 ................................................................................75
13.1 Typical Power Distribution - RECOMMENDED..........................................................75
13.2 Lower Profile Package - Physical Dimensions - REQUIRED........................................79
13.3 Fan Requirements - REQUIRED............................................................................79
13.4 Top Fan Mount Package - Physical Dimensions - REQUIRED .....................................81
13.5 Fan Requirements - REQUIRED............................................................................81
13.6 Reduced Depth Top Mount Fan - Physical Dimensions - REQUIRED ...........................83
13.7 Fan Requirements - REQUIRED............................................................................83
13.8 Standard SFX Profile Package - Physical Dimensions - REQUIRED .............................84
13.9 Fan Requirements - REQUIRED............................................................................85
13.10 PS3 Form Factor- Physical Dimensions - REQUIRED ................................................86
13.11 Fan Requirements - REQUIRED............................................................................86
14 TFX12V Specific Guidelines 2.3 ................................................................................89
14.1 Typical Power Distribution - RECOMMENDED..........................................................89
14.2 Physical Dimensions - REQUIRED .........................................................................94
4
14.3 Mounting Options - RECOMMENDED..................................................................... 97
14.4 Chassis Requirements - RECOMMENDED............................................................... 97
15 Flex ATX Specific Guidelines 1.0 .............................................................................. 99
15.1 Typical Power Distribution - RECOMMENDED ......................................................... 99
15.2 Physical Dimensions - REQUIRED ...................................................................... 103
Figures
1 Differential Noise Test Setup ..................................................................................... 24
2 Power Supply Timing ................................................................................................ 25
3 PS_ON# Signal Characteristics................................................................................... 27
4 PSU Efficiency as Percentage of Output ....................................................................... 30
5 PSU Efficiency per Power for 450 W PSU ..................................................................... 31
6 PSU Efficiency per Power for 250 W PSU ..................................................................... 31
7 Connectors (Pin-side view, not to scale) ...................................................................... 34
8 Serial ATA* Power Connector..................................................................................... 36
9 Cross Loading Graph for 180 W Configurations............................................................. 49
10 Cross Loading Graph for 220 W Configurations............................................................. 50
11 Cross Loading Graph for 270 W Configuration .............................................................. 51
12 Cross Loading Graph for 300 W Configuration .............................................................. 52
13 CFX12V Mechanical Outline ....................................................................................... 54
14 Cross Loading Graph for 180 W Configuration .............................................................. 55
15 Cross Loading Graph for 220 W Configurations............................................................. 56
16 Cross Loading Graph for 270 W Configuration .............................................................. 57
17 Mechanical Outline ................................................................................................... 59
18 Mechanical Details.................................................................................................... 60
19 PSU Slot Feature Detail............................................................................................. 60
20 Recommended Chassis Tab Feature ............................................................................ 61
21 Cross Loading Graph for 180 W Configurations............................................................. 63
22 Cross Loading Graph for 220 W Configurations............................................................. 64
23 Cross Loading Graph for 270 W Configurations............................................................. 65
24 Cross Loading Graph for 300 W Configurations............................................................. 66
25 Cross Loading Graph for 350 W Configurations............................................................. 67
26 Cross Loading Graph for 400 W Configurations............................................................. 68
27 Cross Loading Graph for 450 W Configurations............................................................. 69
28 Power Supply Dimensions for Chassis that does not Require Top Venting ......................... 72
29 Power Supply Dimensions for Chassis that Require Top Venting...................................... 73
30 Cross Loading Graph for 180 W Configuration .............................................................. 75
31 Cross Loading Graph for 220 W Configurations............................................................. 76
32 Cross Loading Graph for 270 W Configuration .............................................................. 77
33 Cross Loading Graph for 300 W Configuration .............................................................. 78
34 40 mm Profile Mechanical Outline............................................................................... 80
35 Chassis Cutout ........................................................................................................ 80
36 Top Mount Fan Profile Mechanical Outline .................................................................... 82
37 Chassis Cutout ........................................................................................................ 83
38 Recessed Fan Mounting............................................................................................. 83
39 Reduced Depth Top Mount Fan Profile Mechanical Outline .............................................. 84
40 Chassis Cutout ........................................................................................................ 84
41 60 mm Mechanical Outline ........................................................................................ 85
42 Chassis Cutout ........................................................................................................ 86
43 PS3 Mechanical Outline ............................................................................................. 87
44 Cross Loading Graph for 180 W Configuration .............................................................. 89
45 Cross Loading Graph for 220 W Configurations............................................................. 90
46 Cross Loading Graph for 270 W Configuration .............................................................. 91
5
47 Cross Loading Graph for 300 W Configuration...............................................................92
48 Mechanical Outline....................................................................................................94
49 Dimensions & Recommended Feature Placements (not to scale)......................................95
50 Power Supply Mounting Slot Detail..............................................................................96
51 Fan Right and Fan Left Orientations of Power Supply in a Chassis....................................97
52 Suggested TFX12V Chassis Cutout ..............................................................................97
53 Suggested Mounting Tab (chassis feature) ...................................................................98
54 Cross Loading Graph for 180 W Configuration...............................................................99
55 Cross Loading Graph for 220 W Configurations ........................................................... 100
56 Cross Loading Graph for 270 W Configuration............................................................. 101
57 Mechanical Outline.................................................................................................. 103
58 Dimensions & Recommended Feature Placements (not to scale).................................... 104
6
Tables
1 Conventions and Terminology .................................................................................... 12
2 Support Terminology ................................................................................................ 13
3 Digital Home Platform Configurations for 2007 - Lifestyle EPC Mainstream ....................... 15
4 Digital Home Platform Configurations for 2007 - CE EPC ................................................ 15
5 Digital Home Platform Configurations for 2007 - Lifestyle EPC Premium ........................... 16
6 Digital Home Platform Configurations for 2007 - Extreme Gaming and Media ................... 16
7 Digital Office Platform Configurations for 2007 - Entry................................................... 17
8 Digital Office Platform Configurations for 2007 - Fundamental ........................................ 17
9 Digital Office Platform Configurations for 2007 - Professional ......................................... 18
10 Digital Office Platform Configurations for 2007 - High Performance ................................. 18
11 Digital Office Platform Configurations for 2006 ............................................................. 19
12 Digital Home Platform Configurations for 2006 ............................................................. 19
13 12V2 Current for Processor Configurations................................................................... 19
14 AC Input Line Requirements ...................................................................................... 21
15 DC Output Voltage Regulation.................................................................................... 22
16 DC Output Transient Step Sizes ................................................................................. 22
17 Recommended 5 VSB Efficiency ................................................................................. 23
18 DC Output Noise/Ripple ............................................................................................ 23
19 Output Capacitive Loads ........................................................................................... 24
20 PWR_OK Signal Timing ............................................................................................. 25
21 PWR_OK Signal Characteristics .................................................................................. 26
22 PS_ON# Signal Characteristics................................................................................... 26
23 Over Voltage Protection ............................................................................................ 28
24 Efficiency Versus Load .............................................................................................. 29
25 Power Supply Sizes for ENERGY STAR Desktop System Categories.................................. 32
26 Main Power Connector Pin-out ................................................................................... 34
27 Peripheral Connector Pin-out ..................................................................................... 35
28 Floppy Connector Pin-out .......................................................................................... 35
29 +12 V Power Connector Pin-out ................................................................................. 36
30 Serial ATA* Power Connector Pin-out .......................................................................... 36
31 Recommended Power Supply Acoustic Targets ............................................................. 39
32 Harmonic Limits, Class D Equipment........................................................................... 43
33 Typical Power Distribution for 180 W Configurations ..................................................... 49
34 Typical Power Distribution for 220 W Configurations ..................................................... 50
35 Typical Power Distribution for 270 W Configurations ..................................................... 51
36 Typical Power Distribution for 300 W Configurations ..................................................... 52
37 180 W Loading for Efficiency Measurements ................................................................ 52
38 220 W Loading for Efficiency Measurements ................................................................ 53
39 270 W Loading for Efficiency Measurements ................................................................ 53
40 300 W Loading for Efficiency Measurements ................................................................ 53
41 Typical Power Distribution for 180 W Configurations ..................................................... 55
42 Typical Power Distribution for 220 W Configurations ..................................................... 56
43 Typical Power Distribution for 270 W Configurations ..................................................... 57
44 180 W Loading for Efficiency Measurements ................................................................ 57
45 220 W Loading for Efficiency Measurements ................................................................ 58
46 270 W Loading for Efficiency Measurements ................................................................ 58
47 Typical Power Distribution for 180 W Configurations ..................................................... 63
48 Typical Power Distribution for 220 W Configurations ..................................................... 64
49 Typical Power Distribution for 270 W Configurations ..................................................... 65
50 Typical Power Distribution for 300 W Configurations ..................................................... 66
51 Typical Power Distribution for 350 W Configurations ..................................................... 67
52 Typical Power Distribution for 400 W Configurations ..................................................... 68
53 Typical Power Distribution for 450 W Configurations ..................................................... 69
7
54 180 W Loading for Efficiency Measurements .................................................................69
55 220 W Loading for Efficiency Measurements .................................................................70
56 270 W Loading for Efficiency Measurements .................................................................70
57 300 W Loading for Efficiency Measurements .................................................................70
58 350 W Loading for Efficiency Measurements .................................................................70
59 400 W Loading for Efficiency Measurements .................................................................70
60 450 W Loading for Efficiency Measurements .................................................................71
61 Typical Power Distribution for 180 W Configurations ......................................................75
62 Typical Power Distribution for 220 W Configurations ......................................................76
63 Typical Power Distribution for 270 W Configurations ......................................................77
64 Typical Power Distribution for 300 W Configurations ......................................................78
65 180 W Loading for Efficiency Measurements .................................................................78
66 220 W Loading for Efficiency Measurements .................................................................79
67 270 W Loading for Efficiency Measurements .................................................................79
68 300 W Loading for Efficiency Measurements .................................................................79
69 Typical Power Distribution for 180 W Configurations ......................................................89
70 Typical Power Distribution for 220 W Configurations ......................................................90
71 Typical Power Distribution for 270 W Configurations ......................................................91
72 Typical Power Distribution for 300 W Configurations ......................................................92
73 180 W Loading for Efficiency Measurements .................................................................92
74 220 W Loading for Efficiency Measurements .................................................................93
75 270 W Loading for Efficiency Measurements .................................................................93
76 300 W Loading for Efficiency Measurements .................................................................93
77 Typical Power Distribution for 180 W Configurations ......................................................99
78 Typical Power Distribution for 220 W Configurations .................................................... 100
79 Typical Power Distribution for 270 W Configurations .................................................... 101
80 180 W Loading for Efficiency Measurements ............................................................... 101
81 220 W Loading for Efficiency Measurements ............................................................... 102
82 270 W Loading for Efficiency Measurements ............................................................... 102
8
Contents
• Removed outdated ENERGY STAR* requirements and added some new ENERGY
STAR information.
• Updated Typical Power Distribution tables for all power supply form factors and
updated minimum loads.
• Updated cross regulation figures.
1.1 • Added Flex ATX power supply form factor. March 2007
• Updated capacitive loading table.
• Clarified over voltage and over current verbiage.
• Added Power-up Cross Loading Condition section.
• Other changes shown in red with change bars.
9
10
Introduction
1 Introduction
This document provides design suggestions for various power supply form factors. The
power supplies are primarily intended for use with desktop system designs. It should
not be inferred that all power supplies must conform exactly to the content of this
document, though there are key parameters that define mechanical fit across a
common set of platforms. Since power supply needs vary depending on system
configuration, the design specifics described are not intended to support all possible
systems.
Document
Document Number/Source or
Password
11
Introduction
Document
Document Number/Source or
Password
EN 61000-4-6 – RF Conducted
EN 61000-4-8 – Power Frequency Magnetic Fields
EN 61000-4-11 – Voltage Dips, Short Interrupts and
Fluctuations
EN61000-3-2 (Harmonics)
EN61000-3-3 (Voltage Flicker)
EU EMC Directive ((8/9/336/EEC) (CE Compliance)
1.2 Terminology
Table 1 defines the acronyms, conventions, and terminology that are used throughout
the design guide.
Acronym, Convention/
Definition
Terminology
12
Introduction
Category Description
The status given to items within this design guide, which are not
required to meet design guide, however, some system applications
Optional
may optionally use these features. May be a required or
recommended item in a future design guide.
The status given to items within this design guide, which are not
required to meet design guide, however, are required by many
Recommended
system applications. May be a required item in a future design
guide.
The status given to items within this design guide, which are
Required required to meet design guide and a large majority of system
applications.
13
Introduction
14
Platform Configurations
2 Platform Configurations
2.1 Digital Home and Digital Office Platform
Configurations - RECOMMENDED
Table 1 and Table 11 show power supply recommendations for various platform
configurations. These configurations are based on platforms described in the Digital
Home and Digital Office Desktop Platform Vision Guides for 2006. Additional
configuration details can be found at the Intel® Platform Vision Program website:
http://www.intel.com/platforms/desktop/vision/
The configurations here and the recommended power supplies are suggestions. System
designers should perform engineering analysis based on the specific system
configuration to determine the appropriate power supply for their needs.
Table 3. Digital Home Platform Configurations for 2007 - Lifestyle EPC Mainstream
Processor TDP 65 W 95 W 65 W 95 W
Chipset Intel® G35 chipset
Memory 2 DDR3 DIMMs, 1066 MHz, 1 GB
Graphics Integrated 1 PCI Express* x16 add-in (75 W)
Audio Intel® High Definition Audio
LAN Intel® 82566 1 Gb LAN
Add-in cards Wireless LAN, 1394, TV tuner/capture
15
Platform Configurations
Table 5. Digital Home Platform Configurations for 2007 - Lifestyle EPC Premium
Table 6. Digital Home Platform Configurations for 2007 - Extreme Gaming and Media
16
Platform Configurations
Table 6. Digital Home Platform Configurations for 2007 - Extreme Gaming and Media
Processor TDP 65 W 95 W
Chipset Intel® 946GZ chipset
Memory 1 DDR2 DIMM, 667 MHz, 512 MB
Graphics Integrated
Audio Intel® High Definition Audio
LAN 10/100M LAN
Add-in cards None
Hard drive 1 SATA hard drive
Optical drive 1 SATA optical drive
USB devices 2 high power and 10 low power USB devices
Fans 1 processor fan, 1 chassis fan
ATX12V, SFX12V, ATX12V, SFX12V,
Power Supply TFX12V, CFX12V, TFX12V, CFX12V,
Recommendation LFX12V, Flex ATX LFX12V, Flex ATX
180 W 220 W
Processor TDP 65 W 95 W
Chipset Intel® Q33 chipset
Memory 2 DDR2 DIMMs, 800 MHz, 1 GB
Graphics Integrated
Audio Intel® High Definition Audio
LAN Intel® 82566 1 Gb LAN
Add-in cards None
Hard drive 1 SATA hard drive
Optical drive 1 SATA optical drive
17
Platform Configurations
Processor TDP 65 W 95 W
Chipset Intel® Q35 chipset
Memory 2 DDR2 DIMMs, 800 MHz, 1 GB
Graphics Integrated
Audio Intel® High Definition Audio
LAN Intel® 82566 1 Gb LAN
Add-in cards Wireless LAN
Hard drive 1 SATA hard drive
Optical drive 1 SATA optical drive
USB devices 2 high power and 10 low power USB devices
Fans 1 processor fan
Table 10. Digital Office Platform Configurations for 2007 - High Performance
Power Supply LFX12V, Flex ATX LFX12V, Flex ATX LFX12V, Flex ATX
Recommendation 180 W 220 W 270 W
18
Platform Configurations
Fundamental Professional
Small sleek CE
BTX family with
Form Factor BTX family form factor BTX family
expandibility
based on BTX
2-4” height for
~25+ liter tower
Profile/ use with
Lifestyle varies Lifestyle varies system for maximum
volume Consumer
expandability
Electronics racks
Power
CFX12V 300 W CFX12V 300 W ATX12V 450 W EPS12V ≥ 600 W1
supply
NOTES:
1. The EPS12V power supply design guide can be found at the SSI Forum website:
http://ssiforum.org/specifications.aspx#powerSupplies
Processor
Processor TDP Continuous Peak1
Configuration
04A 84 W 13 A -
04B 115 W 13 A -
05A 95 W 13 A 16.5 A
2
105 W 14 A 18 A
05B
130 W 16 A 19 A
06 65 W 8A 13 A
NOTES:
1. The power supply should be able to supply peak current for at least 10 ms.
2. The 05B processor configuration full TDP is 130 W. However, some processors that fall into this configuration
will have lower TDP values such as 105 W.
19
Platform Configurations
20
Electrical
3 Electrical
The following electrical requirements are required and must be met over the
environmental ranges as defined in Chapter 6 (unless otherwise noted).
Note: OPTIONAL - 115 VAC or 230 VAC only power supplies are an option for specific
geographical or other requirements.
21
Electrical
+12V1DC 40% -
+12V2DC 60% -
+5 VDC 30% -
+3.3 VDC 30% -
-12 VDC - 0.1
+5 VSB - 0.5
NOTES:
1. For example, for a rated +5 VDC output of 14 A, the transient step would be 30% × 14 A = 4.2 A.
Output voltages should remain within the regulation limits of Table 15, for
instantaneous changes in load as specified in Table 16 and for the following conditions:
• Simultaneous load steps on the +12 VDC, +5 VDC, and +3.3 VDC outputs (all
steps occurring in the same direction)
• Load-changing repetition rate of 50 Hz to 10 kHz
• AC input range per Section 2.1 and Capacitive loading per Table 19.
22
Electrical
Load Efficiency
100 mA ≥ 50%
250 mA ≥ 60%
≥1 A ≥ 70%
Ripple and noise are defined as periodic or random signals over a frequency band of 10
Hz to 20 MHz. Measurements shall be made with an oscilloscope with 20 MHz of
bandwidth. Outputs should be bypassed at the connector with a 0.1µF ceramic disk
capacitor and a 10 µF electrolytic capacitor to simulate system loading. See Figure 1 for
the differential noise measurement setup.
23
Electrical
AC Ground
Oscilloscope
General Notes:
1. Load the output with its minimum load current .
2. Connect the probes as shown .
3. Repeat the measurement with maximum load on the
output.
Filter Note:
0.1 uF – Kemet* C1206C104K5RAC or equivalent
±10%, 1206 pkg, 50 V, X7R
10 uF – Vishay* 293D106X0025D2T or equivalent
±20%, D case, 25 V, tantalum
Oscilloscope Note:
Use Tektronix* TDS460 or equivalent and a P 6046
probe or equivalent.
24
Electrical
…
T1 T5
VAC
PS_ON#
…
…
+12 VDC
+5 VDC
+3.3 VDC
} Outputs
95%
10%
…
T2
T3
PWR_OK
T4
3.3.1 PWR_OK
PWR_OK is a “power good” signal. This signal should be asserted high by the power
supply to indicate that the +12 VDC, +5 VDC, and +3.3 VDC outputs are within the
regulation thresholds listed in Table 15 and that sufficient mains energy is stored by the
converter to guarantee continuous power operation within specification for at least the
duration specified in Section 3.2.9. Conversely, PWR_OK should be de-asserted to a
low state when any of the +12 VDC, +5 VDC, or +3.3 VDC output voltages falls below
its under voltage threshold, or when mains power has been removed for a time
sufficiently long such that power supply operation cannot be guaranteed. The electrical
and timing characteristics of the PWR_OK signal are given in Table 21 and in Figure 2.
25
Electrical
3.3.3 PS_ON#
PS_ON# is an active-low, TTL-compatible signal that allows a motherboard to remotely
control the power supply in conjunction with features such as soft on/off, Wake on
LAN*, or wake-on-modem. When PS_ON# is pulled to TTL low, the power supply
should turn on the four main DC output rails: +12 VDC, +5 VDC, +3.3 VDC, and -12
VDC. When PS_ON# is pulled to TTL high or open-circuited, the DC output rails should
not deliver current and should be held at zero potential with respect to ground.
PS_ON# has no effect on the +5 VSB output, which is always enabled whenever the AC
power is present. Table 22 lists PS_ON# signal characteristics.
The power supply shall provide an internal pull-up to TTL high. The power supply shall
also provide de-bounce circuitry on PS_ON# to prevent it from oscillating on/off at
startup when activated by a mechanical switch. The DC output enable circuitry must be
SELV-compliant.
The power supply shall not latch into a shutdown state when PS_ON# is driven active
by pulses between 10 ms to 100 ms during the decay of the power rails.
VIL 0 0.8 V
IIL (VIN = 0.4 V) - -1.6 mA1
VIH (IIN = - 200 uA) 2.0 V -
VIH open circuit - 5.25 V
NOTES:
1. Negative current indicates that the current is flowing from the power supply to the
motherboard.
26
Electrical
Hysteresis = 0.3 V
Disable
ed
= 0.8 V = 2.0 V
f in
PS is PS is
enabled disabled
de
Un
Enable
0.8 2.0 5.25 = Maximum
Open Circuit Voltage
PS_ON# Voltage
3.3.4 +5 VSB
+5 VSB is a standby supply output that is active whenever the AC power is present.
This output provides a power source for circuits that must remain operational when the
five main DC output rails are in a disabled state. Example uses include soft power
control, Wake on LAN, wake-on-modem, intrusion detection, or suspend state
activities.
The power supply must be able to provide the required power during a “wake up”
event. If an external USB device generates the event, there may be peak currents as
high as 2.5 A., lasting no more than 500 ms.
Over current protection is required on the +5 VSB output regardless of the output
current rating. This ensures the power supply will not be damaged if external circuits
draw more current than the supply can provide.
+5 VSB shall have a power-on time of two seconds maximum after application of valid
AC voltages.
There must be a smooth and continuous ramp of each DC output voltage from 10% to
90% of its final set point within the regulation band, while loaded as specified.
The smooth turn-on requires that, during the 10% to 90% portion of the rise time, the
slope of the turn-on waveform must be positive and have a value of between 0 V/ms
and [Vout, nominal / 0.1] V/ms. Also, for any 5 ms segment of the 10% to 90% rise
time waveform, a straight line drawn between the end points of the waveform segment
must have a slope ≥ [Vout, nominal / 20] V/ms.
27
Electrical
28
Electrical
Over current protection schemes where only the voltage output that experiences the
over current event is shut off may be adequate to maintain safe operation of the power
supply and the system; however, damage to the motherboard or other system
components may occur. The recommended over current protection scheme is for the
power supply to latch into the shutdown state.
29
Electrical
The RECOMMENDED minimum efficiency levels shown in Table 24 are required for
ENERGY STAR system compliance based the version 4.0 specification.
The ENERGY STAR computer specification requires at least 80% efficiency at 20%, 50%
and 100% of the rated output capacity. This effectively provides a window of high
efficiency that extends from 20% to 100% of the rated capacity of the power supply.
Generally the efficiency of the power supply drops off significantly as the load falls
below 20%. Because the power supply is one of the largest contributors to power loss
in the system, it is important to maximize the efficiency in order to comply with the
power targets for the various system categories. Below are two case examples for the
desktop category B system to illustrate this concept. For these two cases, assume the
efficiency curve in terms of percentage of the output is equivalent. This curve is shown
in Figure 4.
100%
90%
80%
70%
Efficiency (%)
60%
50%
40%
30%
20%
10%
0%
0% 20% 40% 60% 80% 100% 120%
Percentage of Output Capacity (%)
NOTES:
1. Graph is an estimated representation for illustrative purposes only.
2. This is not a recommended PSU efficiency curve. It is just included here as an example for
the discussion of properly sizing the PSU for power savings.
CASE 1
For Case 1, suppose the system we are trying to configure to meet the desktop
category B has a 450 W internal power supply. The category B idle power specification
is 65 W AC wall power. The AC wall power is calculated or derived as shown in the
following equation:
(W)
AC ( W ) = DC
-------------
η PSU
In order to minimize the AC wall power, we need to maximize the power supply
efficiency. As can be seen from Figure 5, for a 450 W power supply, the efficiency is low
when the system is at 65 W AC wall power. Because the category B system at idle is on
the part of the power supply efficiency curve where the efficiency is low, the remaining
power budget for the other system components is much less than if the power supply
efficiency was higher.
30
Electrical
CASE 2
For Case 2, assume the system we are trying to configure for category B has a 250 W
power supply. In this case, Figure 6 shows that for an idle state of 65 W AC wall power,
the system is within the high efficiency window of the power supply.
Since the system is operating within the high efficiency window of the power supply
when in the idle state, the power supply losses are minimized which allows additional
budget for other system components.
The examples in Case 1 and Case 2 above show that building the system with a power
supply that is the proper size will maximize the power supply efficiency and allow the
most flexibility for selecting other components in the system.
In order to stay within the ≥ 80% efficiency window generally, the power supply sizes
for each of the desktop system categories are shown in Table 25.
31
Electrical
Table 25. Power Supply Sizes for ENERGY STAR Desktop System Categories
AC Wall Power -
System Category Maximum Power Supply Size1
System Idle
A 50 W ≤ 200 W
B 65 W ≤ 260 W
C 95 W ≤ 380 W
NOTES:
1. The power supply sizes shown this table represent the maximum size in order to stay within the ≥ 80%
efficiency window. It is important; however, to ensure that the power supply also has sufficient capacity to
handle the active or heavy workloads that the system may be subjected to. Larger power supplies are
sometimes needed to allow for future system upgrades though a trade-off for efficiency in the idle state may
be necessary.
32
Mechanical
4 Mechanical
This section contains mechanical guidelines that apply to desktop power supplies
regardless of form factor. For form factor specific design guides refer to Chapter 10
through Chapter 14.
Manufacturer information: manufacturer's name, part number and lot date code, etc.,
in human-readable text and/or bar code formats
Nominal AC input operating voltages (100-127 VAC and 200-240 VAC) and current
rating certified by all applicable safety agencies
Access warning text (“Do not remove this cover. Trained service personnel only. No user
serviceable components inside.”) must be in English, German, Spanish, French,
Chinese, and Japanese with universal warning markings.
4.2.2 DC Connectors
Figure 7 shows pin outs and profiles for typical power supply DC harness connectors.
The power supply requires an additional two-pin, power connector.
UL Listed or recognized component appliance wiring material rated min 85 °C, 300 VDC
shall be used for all output wiring.
There are no specific requirements for output wire harness lengths, as these are largely
a function of the intended end-use chassis, motherboard, and peripherals. Ideally,
wires should be short to minimize electrical/airflow impedance and simplify
manufacturing, yet they should be long enough to make all necessary connections
without any wire tension (which can cause disconnections during shipping and
handling). Recommended minimum harness lengths for general-use power supplies is
150 mm for all wire harnesses. Measurements are made from the exit port of the
power supply case to the wire side of the first connector on the harness.
33
Mechanical
1 13
1 +12V1 DC
+3.3 VDC +3.3 VDC
Pin 1
+3.3 VDC -12 VDC +3.3 VDC
COM
+3.3 VDC
COM COM
COM +3.3 VDC
+5 VDC PS_ON# COM
COM
COM COM 4 +5 VDC
COM
+5 VDC COM +5 VDC
1 3
COM +12V2 DC
COM +12V2 DC
+12V2 DC
Connector
18 AWG is suggested for all wires except for the +3.3 V supply and sense return wires
combined into pin 13 (22 AWG).
+3.3 VDC
13 [+3.3 V Orange
1 +3.3 VDC Orange
[13] default [Brown]
sense]
2 +3.3 VDC Orange 14 -12 VDC Blue
3 COM Black 15 COM Black
4 +5 VDC Red 16 PS_ON# Green
5 COM Black 17 COM Black
6 +5 VDC Red 18 COM Black
34
Mechanical
1 +5 VDC Red
2 COM Black
3 COM Black
4 +12 V1DC Yellow
NOTES:
1. 20 AWG wire.
35
Mechanical
The detailed requirements for the Serial ATA Power Connector can be found in the
“Serial ATA: High Speed Serialized AT Attachment” specification, Section 6.3 “Cables
and connector specification”.
http://www.serialata.org/
Note: Connector pin numbers and wire numbers are not 1:1. Carefully check to confirm the
correct arrangement.
36
Mechanical
The power supply fan should be turned off when PS_ON# is de-asserted (high). In this
state, any remaining active power supply circuitry must rely only on passive convection
for cooling.
37
Mechanical
4.3.3 Venting
In general, more venting in a power supply case yields reduced airflow impedance and
improved cooling performance. Intake and exhaust vents should be large, open, and
unobstructed as possible so as not to impede airflow or generate excessive acoustic
noise. In particular, avoid placing objects within 0.5 inches of the intake or exhaust of
the fan itself. A flush-mount wire fan grill can be used instead of a stamped metal vent
for improved airflow and reduced acoustic noise.
38
Acoustics
5 Acoustics
5.1 Acoustics - RECOMMENDED
It is recommended that the power supply be designed with an appropriate fan, internal
impedance, and fan speed control circuitry capable of meeting the acoustic targets
listed in Table 31.
The power supply assembly shall not produce and prominent discrete tone determined
according to ISO 7779, Annex D.
39
Acoustics
40
Environmental
6 Environmental
The following subsections define environmental specifications and test parameters,
based on the typical conditions to which a power supply may be subjected during
operation or shipment.
41
Environmental
42
Electromagnetic Compatibility
7 Electromagnetic Compatibility
The following subsections outline applicable product regulatory requirements for the
power supplies. Additional requirements may apply dependent upon the design,
product end use, target geography, and other variables.
Class D and the Guidelines for the Suppression of Harmonics in Appliances and General
Use Equipment Class D for harmonic line current content at full rated power. See for the
harmonic limits.
For sales in Japan the power supply shall meet the requirements of JEIDA MITI.
Maximum permissible
Harmonic Order Maximum permissible harmonic
harmonic current at 230 VAC
(n) current at 100 VAC / 50 Hz (A)
/ 50 Hz (A)
3 2.3 5.29
5 1.14 2.622
7 0.77 1.771
9 0.4 0.92
11 0.33 0.759
13 0.21 0.483
15 = n = 39 0.15 x (15/n) 0.345 x (15/n)
43
Electromagnetic Compatibility
44
Safety
8 Safety
The following subsections outline sample product regulations requirements for a typical
power supply. Actual requirements will depend on the design, product end use, target
geography, and other variables. Consult your company’s Product Safety and
Regulations department or an accredited third party certification agency for more
details.
The power supply must meet the RoHS requirements for the European Union, Peoples
Republic of China and other countries which have adopted the RoHS requirements for
banned materials.
45
Safety
46
Reliability
9 Reliability
9.1 Reliability - RECOMMENDED
The de-rating process promotes quality and high reliability. All electronic components
should be designed with conservative device de-ratings for use in commercial and
industrial environments.
Electrolytic capacitor and fan lifetime and reliability should be considered in the design
as well.
47
Reliability
48
CFX12V Specific Guidelines 1.4
Significant dependencies include the quantity and types of processors, memory, add-in
card slots, and peripheral bays, as well as support for advanced graphics or other
features. Figure 9 through Figure 12 shows the power distribution and cross loading
tables for power supplies in the range of 180 W to 300 W. These are recommendations
but it is ultimately the responsibility of the designer to define a power budget for a
given target product and market.
90
80 95, 80
5 V + 3.3 V power (W)
45, 80
70
60
120, 55
50
20, 45
40
30
1.2, 16
20 120, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150
Total 12 V power (W)
49
CFX12V Specific Guidelines 1.4
NOTES:
1. Total combined output of 3.3 V and 5 V is ≤ 80 W.
90
80 135, 80
5 V + 3.3 V power (W)
70
60
50 168, 47
20, 45
40
30 1.2, 20
20 168, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150 200
Total 12 V power (W)
50
CFX12V Specific Guidelines 1.4
120
5 V + 3.3 V power (W)
100 60, 97 168, 97
80
60 204, 61
20, 45
40
1.2, 20
20 204, 16
5.8, 5.4 20.4, 5.4
0
0 50 100 150 200 250
Total 12 V power (W)
51
CFX12V Specific Guidelines 1.4
120
70, 103 192, 103
100
5 V + 3.3 V power (W)
80 216, 79
60
20, 50
40
1.2, 20
20 216, 16
5.8, 5.4
0 20.4, 5.4
52
CFX12V Specific Guidelines 1.4
53
CFX12V Specific Guidelines 1.4
54
LFX12V Specific Guidelines 1.2
Significant dependencies include the quantity and types of processors, memory, add-in
card slots, and peripheral bays, as well as support for advanced graphics or other
features. Figure 14 through Figure 16 shows the power distribution and cross loading
tables for power supplies in the range of 180 W to 270 W. These are recommendations
but it is ultimately the responsibility of the designer to define a power budget for a
given target product and market.
90
80 95, 80
5 V + 3.3 V power (W)
45, 80
70
60
120, 55
50
20, 45
40
30
1.2, 16
20 120, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150
Total 12 V power (W)
55
LFX12V Specific Guidelines 1.2
90
80 135, 80
5 V + 3.3 V power (W)
70
60
50 168, 47
20, 45
40
30 1.2, 20
20 168, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150 200
Total 12 V power (W)
56
LFX12V Specific Guidelines 1.2
120
5 V + 3.3 V power (W)
100 60, 97 168, 97
80
60 204, 61
20, 45
40
1.2, 20
20 204, 16
5.8, 5.4 20.4, 5.4
0
0 50 100 150 200 250
Total 12 V power (W)
57
LFX12V Specific Guidelines 1.2
58
LFX12V Specific Guidelines 1.2
59
LFX12V Specific Guidelines 1.2
60
LFX12V Specific Guidelines 1.2
61
LFX12V Specific Guidelines 1.2
62
ATX12V Specific Guidelines 2.3
Significant dependencies include the quantity and types of processors, memory, add-in
card slots, and peripheral bays, as well as support for advanced graphics or other
features. Figure 22 through Figure 26 shows the power distribution and cross loading
tables for power supplies in the range of 180 W to 450 W. These are recommendations
but it is ultimately the responsibility of the designer to define a power budget for a
given target product and market.
90
80 95, 80
5 V + 3.3 V power (W)
45, 80
70
60
120, 55
50
20, 45
40
30
1.2, 16
20 120, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150
Total 12 V power (W)
63
ATX12V Specific Guidelines 2.3
NOTES:
1. Peak currents may last up to 17 seconds with not more than one occurrence per minute.
2. Total combined output of 3.3 V and 5 V is ≤ 80 W.
90
80 135, 80
5 V + 3.3 V power (W)
70
60
50 168, 47
20, 45
40
30 1.2, 20
20 168, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150 200
Total 12 V power (W)
64
ATX12V Specific Guidelines 2.3
120
5 V + 3.3 V power (W) 100 60, 97 168, 97
80
60 204, 61
20, 45
40
1.2, 20
20 204, 16
5.8, 5.4 20.4, 5.4
0
0 50 100 150 200 250
Total 12 V power (W)
65
ATX12V Specific Guidelines 2.3
120
70, 103 192, 103
100
5 V + 3.3 V power (W)
80 216, 79
60
20, 50
40
1.2, 20
20 216, 16
5.8, 5.4
0 20.4, 5.4
Output Minimum Current (A) Maximum Current (A) Peak Current (A)1
66
ATX12V Specific Guidelines 2.3
120
100, 103 242, 103
5 V + 3.3 V power (W) 100
80 264, 81
60 40, 60
40
1.2, 20
20 264, 16
5.8, 5.4
20.4, 5.4
0
0 50 100 150 200 250 300
Total 12 V power (W)
Output Minimum Current (A) Maximum Current (A) Peak Current (A)1
67
ATX12V Specific Guidelines 2.3
140
120 120, 120 275, 120
5 V + 3.3 V power (W)
100 300, 95
80
50, 65
60
40
1.2, 20
20 5.8, 5.4 300, 16
0 20.4, 5.4
Output Minimum Current (A) Maximum Current (A) Peak Current (A)1
68
ATX12V Specific Guidelines 2.3
140
5 V + 3.3 V power (W) 120 130, 120 325, 120
100
360, 85
80
50, 65
60
40
1.2, 20
20 5.8, 5.4 360, 16
20.4, 5.4
0
0 100 200 300 400
Total 12 V power (W)
Output Minimum Current (A) Maximum Current (A) Peak Current (A)1
69
ATX12V Specific Guidelines 2.3
70
ATX12V Specific Guidelines 2.3
71
ATX12V Specific Guidelines 2.3
Figure 28. Power Supply Dimensions for Chassis that does not Require Top Venting
WIRE HARNESS
16 REF
150 REF
20.0
4.0X6 (2X)
(2X)
72
ATX12V Specific Guidelines 2.3
Figure 29. Power Supply Dimensions for Chassis that Require Top Venting
53 REF
WIRE HARNESS
5.0
45.0
8.0 114.0
No. 6-32 UNC-2B THREADED HOLE (4X) 138.0 86 REF
73
ATX12V Specific Guidelines 2.3
74
SFX12V Specific Guidelines 3.2
Significant dependencies include the quantity and types of processors, memory, add-in
card slots, and peripheral bays, as well as support for advanced graphics or other
features. Figure 30 through Figure 33 shows the power distribution and cross loading
tables for power supplies in the range of 180 W to 300W. These are recommendations
but it is ultimately the responsibility of the designer to define a power budget for a
given target product and market.
90
80 95, 80
5 V + 3.3 V power (W)
45, 80
70
60
120, 55
50
20, 45
40
30
1.2, 16
20 120, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150
Total 12 V power (W)
75
SFX12V Specific Guidelines 3.2
90
80 135, 80
5 V + 3.3 V power (W)
70
60
50 168, 47
20, 45
40
30 1.2, 20
20 168, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150 200
Total 12 V power (W)
76
SFX12V Specific Guidelines 3.2
120
5 V + 3.3 V power (W) 100 60, 97 168, 97
80
60 204, 61
20, 45
40
1.2, 20
20 204, 16
5.8, 5.4 20.4, 5.4
0
0 50 100 150 200 250
Total 12 V power (W)
77
SFX12V Specific Guidelines 3.2
120
70, 103 192, 103
100
5 V + 3.3 V power (W)
80 216, 79
60
20, 50
40
1.2, 20
20 216, 16
5.8, 5.4
0 20.4, 5.4
78
SFX12V Specific Guidelines 3.2
79
SFX12V Specific Guidelines 3.2
85.0
40mm Fan
OP Wire Harness -
Location is at
manufacturer's discretion
100.0
85.0 Airflow
4.0X6
6.0
Venting holes
OPTIONAL -
to outside of
chassis
125.0
Airflow
Notes:
1. Unless otherwise specified, all
dimensions are in mm. 115/220 No. 6-32 UNC-2B
Tolerance: Threaded Hole (3X)
Whole No.: XX +/- 1 50.0
Decimal No.: X.X +/- 0.5 38.0
6.0 31.8
2. Do not scale drawing.
Ø4x3
4.0
14.5
88.0
96.0
80
SFX12V Specific Guidelines 3.2
To prevent damage to the fan during shipment and handling, the power supply designer
should consider recessing the fan mounting, as shown in Figure 38.
81
SFX12V Specific Guidelines 3.2
OP Wire Harness-
Location is at
manufacturer's discretion
12.0
6.0
80mm Fan
125.0 95.8
Airflow
45.5
9.0 X 3.2 cutout
clearance under cutout Airflow
minimum of 4.5 from
17.1
inside cover
6.0
88.0
100.0
82
SFX12V Specific Guidelines 3.2
Ø4x3
8.5
Note: all features of P/S enclosure
59.5 that are outside bold cutout must be
flush with wiht P/S face. Flush mount
51.5 screws if necessary
4.0 135 x 4 34.3
R 5.0 29.8
25.3
4.0
14.5
88.0
96.0
17.1
63.5
83
SFX12V Specific Guidelines 3.2
Figure 39. Reduced Depth Top Mount Fan Profile Mechanical Outline
125.0
OP Wire Harness -
Location is at manufacturer's
discretion
12.0
100.0
59.0 Airflow
15.0 45.5
95.8
80mm Fan
125.0 Airflow
17.1
Notes:
1. Unless otherwise specified, all
No. 6-32 UNC-2B
dimensions are in mm. 115/220
Tolerance: Threaded Hole (3X)
63.5
Whole No.: XX +/- 1
Decimal No.: X.X +/- 0.5 51.5
Ø4x3
4.0
14.5
113.0
121.0
84
SFX12V Specific Guidelines 3.2
85.0
68.5
60mm Fan
OP Wire Harness -
9.0 X 3.2 Cutout Location is at manufacturer's
Clearance under discretion
cutout minimum
4.5 from inside 42.5
cover
27.3 5.0
3.50
6.0
Venting holes
OPTIONAL - to
outside of chassis
125.0
Notes:
1. Unless otherwise specified, all
No. 6-32 UNC-2B
dimensions are in mm. 115/220
Tolerance: Threaded Hole (3X)
Whole No.: XX +/- 1 63.5
Decimal No.: X.X +/- 0.5
51.5
2. Do not scale drawing. 6.0 31.8
85
SFX12V Specific Guidelines 3.2
Ø4x3
4.0
14.5
88.0
96.0
The power supply fan should be turned off when PS_ON# is de-asserted (high). In this
state, any remaining active power supply circuitry must rely only on passive convection
for cooling.
86
SFX12V Specific Guidelines 3.2
OP Wire Harness-
Location is at
manufacturer's discretion
150.0
4.0X6
6.0
101.4
Notes:
1. Unless otherwise specified, all
dimensions are in mm. 80mm Fan
Tolerance:
Whole No.: XX +/- 1
Decimal No.: X.X +/- 0.5 86.0 115/220
64.0 74.0
2. Do not scale drawing.
6.0 114.0
87
SFX12V Specific Guidelines 3.2
88
TFX12V Specific Guidelines 2.3
Significant dependencies include the quantity and types of processors, memory, add-in
card slots, and peripheral bays, as well as support for advanced graphics or other
features. Figure 44 through Figure 47 shows the power distribution and cross loading
tables for power supplies in the range of 180 W to 300 W. These are recommendations
but it is ultimately the responsibility of the designer to define a power budget for a
given target product and market.
90
80 95, 80
5 V + 3.3 V power (W)
45, 80
70
60
120, 55
50
20, 45
40
30
1.2, 16
20 120, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150
Total 12 V power (W)
89
TFX12V Specific Guidelines 2.3
90
80 135, 80
5 V + 3.3 V power (W)
70
60
50 168, 47
20, 45
40
30 1.2, 20
20 168, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150 200
Total 12 V power (W)
90
TFX12V Specific Guidelines 2.3
120
5 V + 3.3 V power (W)
100 60, 97 168, 97
80
60 204, 61
20, 45
40
1.2, 20
20 204, 16
5.8, 5.4 20.4, 5.4
0
0 50 100 150 200 250
Total 12 V power (W)
91
TFX12V Specific Guidelines 2.3
120
70, 103 192, 103
100
5 V + 3.3 V power (W)
80 216, 79
60
20, 50
40
1.2, 20
20 216, 16
5.8, 5.4
0 20.4, 5.4
92
TFX12V Specific Guidelines 2.3
93
TFX12V Specific Guidelines 2.3
94
Figure 49.
A 4.
TFX12V Specific Guidelines 2.3
B 12.8
C 54.8
D 59.64
E 65 6-32 UNC 2-B
F 69.8 57.2 N 2 PLACES 13.5 P
UNLESS OTHERWISE SPECIFIED DESIGNED BY DATE DEPARTMENT R 2200 MISSION COLLEGE BLVD.
F 70.00 S 14.50 INTERPRET DIMENSIONS AND TOLERANCES P.O. BOX 58119
IN ACCORDANCE WITH ASME Y14.5M-1994
-
G 5.20 T 46.30 SANTA CLARA, CA 95052-8119
DIMENSIONS ARE IN MILLIMETERS DRAWN BY DATE
TITLE
H 5.50 U 53.50 ALL UNTOLERANCED LINEAR - -
DIMENSIONS ± 0.1
ANGLES ± 0.5 CHECKED BY DATE
J 76.00 V 175.00
THIRD ANGLE PROJECTION - - TFX
K 80.50 W 65.00 - -
L 85.00 APPROVED BY DATE
SIZE DRAWING NUMBER REV
- -
MATERIAL FINISH A1 TFX_CASE
SEE NOTES SEE NOTES SCALE: 1 DO NOT SCALE DRAWING SHEET 1 OF 2
95
96
Figure 50.
53. D
ITEM DIMENSION
A 2.55 34.52 E
B 14.02
C 18.62
D 53.50
E 30.50
18.6 C
Power Supply Mounting Slot Detail
B 14
UNLESS OTHERWISE SPECIFIED DESIGNED BY DATE DEPARTMENT R 2200 MISSION COLLEGE BLVD.
INTERPRET DIMENSIONS AND TOLERANCES - P.O. BOX 58119
IN ACCORDANCE WITH ASME Y14.5M-1994 SANTA CLARA, CA 95052-8119
DIMENSIONS ARE IN MILLIMETERS DRAWN BY DATE
TITLE
ALL UNTOLERANCED LINEAR - -
DIMENSIONS ± 0.1
ANGLES ± 0.5 CHECKED BY DATE
Figure 51. Fan Right and Fan Left Orientations of Power Supply in a Chassis
97
TFX12V Specific Guidelines 2.3
98
Flex ATX Specific Guidelines 1.0
Significant dependencies include the quantity and types of processors, memory, add-in
card slots, and peripheral bays, as well as support for advanced graphics or other
features. Figure 54 through Figure 56 shows the power distribution and cross loading
tables for power supplies in the range of 180 W to 270 W. These are recommendations
but it is ultimately the responsibility of the designer to define a power budget for a
given target product and market.
90
80 95, 80
5 V + 3.3 V power (W)
45, 80
70
60
120, 55
50
20, 45
40
30
1.2, 16
20 120, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150
Total 12 V power (W)
99
Flex ATX Specific Guidelines 1.0
90
80 135, 80
5 V + 3.3 V power (W)
70
60
50 168, 47
20, 45
40
30 1.2, 20
20 168, 16
10 5.8, 5.4
20.4, 5.4
0
0 50 100 150 200
Total 12 V power (W)
100
Flex ATX Specific Guidelines 1.0
120
5 V + 3.3 V power (W)
100 60, 97 168, 97
80
60 204, 61
20, 45
40
1.2, 20
20 204, 16
5.8, 5.4 20.4, 5.4
0
0 50 100 150 200 250
Total 12 V power (W)
101
Flex ATX Specific Guidelines 1.0
102
Flex ATX Specific Guidelines 1.0
103
104
Figure 58.
150M
68.1 J
75.9 E 15.
K 6-32 UNC-2B
59. F 81.5 L 2 PLACES
W35.9 15.2G 47 N 6 .5
R
A 16.8 4. V 9P Q 50. 15
S
6-32 UNC-2B
4 PLACES
B 40.5 3T2
C 36.1 7U
D 4.1 PREFERRED MFG LABEL
LOCATION
CABLE OUTLET MAY EXIST
IN EITHER LOCATION
ITEM DIMENSION ITEM DIMENSION
A 17.0 M 150.00
B 40.5 N 47.00
C 36.1 P 9.00
D 4.1 Q 50.50
E 76.0 R 66.50
F 60.0 S 15.00
G 15.2 T 32.00
Dimensions & Recommended Feature Placements (not to scale)
J 68.10 U 7.00 UNLESS OTHERWISE SPECIFIED DESIGNED BY DATE DEPARTMENT R 2200 MISSION COLLEGE BLVD.
K 15.10 V 4.40 INTERPRET DIMENSIONS AND TOLERANCES - P.O. BOX 58119
IN ACCORDANCE WITH ASME Y14.5M-1994 SANTA CLARA, CA 95052-8119
DIMENSIONS ARE IN MILLIMETERS DRAWN BY DATE
L 81.50 W 35.90 TITLE
ALL UNTOLERANCED LINEAR - -
DIMENSIONS ± 0.1
CHECKED BY DATE
ANGLES ± 0.5
THIRD ANGLE PROJECTION - - FLEX ATX
- -
APPROVED BY DATE
SIZE DRAWING NUMBER REV
- -
MATERIAL FINISH A1 FLEX_ATX_A1
SEE NOTES SEE NOTES SCALE: 1 DO NOT SCALE DRAWING SHEET 1 OF 1
Flex ATX Specific Guidelines 1.0