Documente Academic
Documente Profesional
Documente Cultură
PROB SET 1
Instruction: Answer the following questions on letter-sized (8.5x11) paper, preferably recycled
(i.e. one side already used). Only one side of every sheet of paper shall be used to write
your solutions to the problems.
I.
10 kN
x
B
C
a'
60
a
2.4 m
200mm
a. Determine the distance x in meters so that the normal stress at section a-a (200x100 mm 2
post C) equals the tensile stress at member A (x-sectional area = 1200 mm2)
b. Find the maximum load, Pmax, that can be applied at x = 1.0 m, maintaining equilibrium,
if the maximum shearing stress at post C is 7.5 MPa and the maximum normal stress of
member A is 10 MPa.
thickness of BC = 6 mm
thickness of BE = 13 mm
Determine:
a. Number of rivets to fasten member BC to the gusset plate.
b. Number of rivets to fasten member BE to the gusset plate.
4. The structure below consists of a circular rod AB (diameter = 25 mm) and a rectangular
boom BC (20mm x 20mm). The rod and the boom are connected by a pin at B. Determine
the Pmax that can be applied at B assuming that normal stresses will govern.
Rod AB
u = 320 MPa
F.S. = 3.0
Boom BC
u = 330 MPa
F.S. = 3.5
a
50
B
3m
30
8m
P
When Pmax is applied, determine:
a. Angle (0 45) if normal stress on plane a-a is 69.46 MPa.
b. What is the corresponding shearing stress on plane a-a?
5. Steel plates B and C are fully glued to member A thus, forming a compound member as
shown in the figure. This will be used to punch two holes in a 10-mm thick wooden plank. If
the maximum average shearing stress in the glue is 600 MPa, and the allowable normal
stress in member A is 900 MPa, (thickness of A, B, and C is 20 mm) determine:
a. Pmax that can be applied to the compound member.
b. Is this force Pmax enough to punch holes in the plank if the failure shearing stress in the
plank is 800 MPa?
P
A A
80 mm
60 mm
B
3. The rigid bar BD is originally in a horizontal position shown. If loads cause the end to be
displaced downwards B=2 mm and the bar rotates =0.2o, determine the average normal
strain in (a) the wires AD and BC, and (b) rod CD if there is a 2 mm gap in the connection at
D.
1m
C
A
wires
1.2 m
1m
B
B
4. Load P is applied on the rigid bar BD causing a shearing strain at point B equal to 0.09
radians. Knowing angle ABC is initially 90 and AB = BC = 0.3 m, determine:
a. normal strain at AB
b. normal strain at BC
P
D
B
20
mm
E
0.5
m
0.5
m
3. A high-strength structural steel bar with diameter 2.0 inches is subjected to a compressive
load. The bar has a modulus of elasticity of 29000 ksi (kip* per square inch) and a Poissons
ratio of 0.29. Due to some limitations to the tolerances, the diameter of the bar cannot
exceed 2.001 inches under load. Determine the maximum permissible load that can be
applied on the bar.
* 1 kip = 1000 pounds
Bonus:
1. Shown below is the simplified version of LA Lakers 2009 NBA Championship trophy.
Determine its moment of inertia Ix and Iy at the centroidal axes of the section. (4 pts)
200 mm
100 mm
400 mm
25 mm
200 mm
2. Draw the shear and bending moment diagram of the member. Indicate values at critical and
turning points of the graph. (3 pts) Hint: mind the pulley at B.
0.4 m
A
12 kN/m
B
C
30 kN
2m
2m
D
4m