Documente Academic
Documente Profesional
Documente Cultură
62.1:DVC6200
September 2013
D103415X012
Features
Reliability
nLinkageLess NonContact Position Feedback The
Performance
nAccurate and Responsive The twostage positioner
Ease of Use
nEnhanced Safety The DVC6200 is a HART
www.Fisher.com
LINKAGELESS
FEEDBACK SYSTEM
W9616
Value
nHardware Savings When installed in an integrated
Product Bulletin
62.1:DVC6200
September 2013
D103415X012
E1208
ERROR
(RED CONDITION INDICATOR)
E1209
E1210
WARNING
(YELLOW CONDITION INDICATOR)
Valve Diagnostics
Product Bulletin
62.1:DVC6200
September 2013
D103415X012
Specifications
Maximum Span: 9.5 bar (140 psig)
Action: J Double, J Single Direct or J Reverse
Available Mounting
J Integral mounting to the Fisher GX Control
Communication Protocol
J HART 5 or J HART 7(1)
Input Signal
PointtoPoint.
Independent Linearity(7)
Typical Value: 0.50% of output span
Electromagnetic Compatibility
Meets EN 613261 (First Edition)
ImmunityIndustrial locations per Table 2 of the
EN 613261 standard.
EmissionsClass A
ISM equipment rating: Group 1, Class A
Multidrop
Instrument Power: 11 to 30 VDC at 10 mA
Reverse Polarity protected
Supply Pressure(3)
Input Impedance
An equivalent impedance of 550 ohms may be used.
This value corresponds to 11V @ 20 mA.
Supply Medium
Air or Natural Gas
Electrical Classification
Hazardous Area Approvals
CSA Intrinsically Safe, Explosionproof, Division 2,
Dust Ignitionproof
FM Intrinsically Safe, Explosionproof,
NonIncendive, Dust Ignitionproof
ATEX Intrinsically Safe, Flameproof, Type n
IECEx Intrinsically Safe, Flameproof, Type n
Product Bulletin
62.1:DVC6200
September 2013
D103415X012
Specifications (continued)
Electrical Housing
CSA Type 4X, IP66
FM Type 4X, IP66
Actuator Compatibility
ATEX IP66
IECEx IP66
Other Classifications/Certifications
Natural Gas Certified, Single Seal Device CSA, FM,
ATEX, and IECEx
Additional Information
For additional information go to www.FIELDVUE.com or
contact your Emerson Process Management sales office.
NOTE: Specialized instrument terms are defined in ANSI/ISA Standard 51.1 - Process Instrument Terminology.
1. Only available with DVC6200 HW2.
2. Values listed are applicable for DVC6200 HW 1. For HW 2: Minimum Voltage Available at Instrument Terminals must be 9.5 VDC for analog control, 10 VDC for HART communication.
3. The pressure/temperature limits in this document and any other applicable code or standard should not be exceeded.
4. Normal m3/hour - Normal cubic meters per hour at 0_C and 1.01325 bar, absolute. Scfh - Standard cubic feet per hour at 60_F and 14.7 psia.
5. Values at 1.4 bar (20 psig) based on a singleacting direct relay; values at 5.5 bar (80 psig) based on doubleacting relay.
6. Temperature limits vary based on hazardous area approval.
7. Not applicable for travels less than 19 mm (0.75 inch) or for shaft rotation less than 60 degrees. Also not applicable for digital valve controllers in longstroke applications.
8. 4conductor shielded cable, 18 to 22 AWG minimum wire size, in rigid or flexible metal conduit, is required for connection between base unit and feedback unit.
9. 420 mA output, isolated; Supply Voltage: 830 VDC; Fault Indication: offrange high or low; Reference Accuracy: 1% of travel span.
10. One isolated switch, configurable throughout the calibrated travel range or actuated from a device alert; Off State: 0 mA (nominal); On State: up to 1 A; Supply Voltage: 30 VDC maximum;
Reference Accuracy: 2% of travel span.
Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher, FIELDVUE, and ValveLink are marks owned by one of the companies in the Emerson Process Management business unit of Emerson Electric Co.
Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. HART is a mark owned by the
HART Communication Foundation. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
E
4 2009, 2013 Fisher Controls International LLC. All rights reserved.