Documente Academic
Documente Profesional
Documente Cultură
ODW-720-F1
Fibre Optic Modem
Industrial Converter
RS-232 to Fibre Optic Link.
Point to Point applications
www.westermo.com
Westermo Teleindustri AB
User Guide
Legal information
The contents of this document are provided as is. Except as required by applicable
law, no warranties of any kind, either express or implied, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose, are made
in relation to the accuracy and reliability or contents of this document. Westermo
reserves the right to revise this document or withdraw it at any time without prior
notice.
Under no circumstances shall Westermo be responsible for any loss of data or income
or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
http://www.westermo.com
2
6651-2221
Safety
Before installation:
Read this manual completely and gather all information on the unit. Make sure
that you understand it fully. Check that your application does not exceed the safe
operating specifications for this unit.
This unit should only be installed by qualified personnel.
This unit should be built-in to an apparatus cabinet, or similar, where access is
restricted to service personnel only.
The power supply wiring must be sufficiently fused, and if necessary it must be
possible to disconnect manually from the power supply. Ensure compliance to
national installation regulations.
Branch circuit protection (fuse) is required for this unit with rating not
exceeding 20 A.
Product should be connected to UL Listed power supplies rated 12 48 VDC,
min 500 mA or 24 VAC, min 500 mA or reliably grounded DC SELV source*.
This unit uses convection cooling.To avoid obstructing the airflow around the
unit, follow the spacing recommendations (see Cooling section).
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
Approval / Compliance
EMC
Safety
ATEX**
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
EN 55022 Notice: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
6651-2221
Marking
II 3 G
Ex nA IIC T4 Gc
SPECIAL CONDITION
WARNING DO NOT SEPARATE WHEN ENERGIZED
Indicate that this unit complies with relevant European standards that are
harmonised with the 94/9/EC Directive (ATEX).
II
G
Ex
nA
IIC
T4
Gc
SPECIAL
CONDITION
6651-2221
Ratings
Power
Ambient temperature
Ingress protection (IP)
Maximum surface temperatur
IP 21
40C to +70C
Minimum 25 mm above / below
Minimum 10 mm left / right
FP
Descripton
In & out / Relay contact (NO)
In & out / Relay contact (C)
In & out / Relay contact (NC)
Descripton
Out / Data Carrier Detect (DCD)
Out / Received Data (RD)
In / Transmitted Data (TD)
Not connected
/ Signal Ground (SG)
Out / Data Set Ready (DSR)
In / Request To Send (RTS)
Out / Clear To Send (CTS)
Not connected
Umax = 12 Vpk
Imax = 60 mA
Data rate:
300 bit/s to 250 kbit/s
123
Position
1
2
3
4
5
6
7
8
9
Position Descripton
Rx
In / Receive port
Tx
Out / Transmit port
Position Descripton
1
In / Common
2
3
4
In / +Voltage A
In / +Voltage B
In / Common
Output values
Max 0 dBm
Intput values
Uin = (10 60) VDC
Iin = 400 mA max
PIn = Max 4 W
6651-2221
6651-2221
Declaration of Conformity
Westermo Teleindustri AB
Declaration of conformity
The manufacturer
Westermo Teleindustri AB
SE-640 40 Stora Sundby, Sweden
Model
Art no
ODW-700 series
3651-07xx
ODW-700EX series
3651-37xx
Short name
2004/108/EC
94/9/EC1
Title
Electromagnetic compatibility Immunity residential environments
Issue
2007
EN 61000-6-2
2005
EN 61000-6-3
2007
EN 61000-6-4
2007
EN 55022
EN 55024
EN 50121-4
1998 + A1:2001 +
A2:2003
2006
EN 60079-0
EN 60079-15
The last two digits of the year in which the CE marking was affixed:
2006 + A1:2007
2009
2005
11
Pierre berg
Technical Manager
15th June 2011
1
Postadress/Postal address
Tel.
Telefax
Postgiro
Bankgiro
Org.nr/
Corp. identity number
Registered office
016-428000
Int+46 16428000
016-428001
Int+46 16428001
52 72 79-4
5671-5550
556361-2604
Eskilstuna
6651-2221
IEC 61000-4-3
ENV 50204
EN 61000-4-4
Surge
EN 61000-4-5
RF conducted
EN 61000-4-6
EN 61000-4-9
EN 61000-4-11
Mains freq. 50 Hz
Mains freq. 50 Hz
Radiated emission
EN 61000-4-16
SS 436 15 03
EN 55022
FCC part 15
EN 55022
FCC part 15
EN 55022
EN 60950
Conducted emission
Dielectric strength
Environmental
Temperature
Shock
Packaging
Enclosure, ODW-720-F1
Enclosure,
ODW-720-F1 EX
Dimension W x H x D
Weight
Degree of protection
Cooling
Mounting
6651-2221
Enclosure
Signal ports
Power ports
Signal ports unbalanced
Signal ports balanced
Power ports
Signal ports
Power ports
Enclosure
AC power ports
Signal ports
Signal ports
Enclosure
AC power ports
AC power ports
DC power ports
Signal port to all other
isolated ports
Power port to other
isolated ports
IEC 60068-2-6
Operating
Storage & Transport
Maximum surface
temperature
Operating
Storage & Transport
Operating
Operating
Operating
IEC 60068-2-27
Operating
UL 94
PC / ABS
Cabelec 6141
Humidity
Altitude
Service life
Vibration
Description
Enclosure contact
Enclosure air
Enclosure
IEC 529
Enclosure
Level
6 kV
8 kV
10 V/m 80% AM (1 kHz), 80 800 MHz
20 V/m 80% AM (1 kHz), 800 1000 MHz
20 V/m 80% AM (1 kHz), 1400 2700 MHz
20 V/m pulse modulated 200 Hz, 900 5 MHz
2 kV
2 kV
2 kV line to earth, 2 kV line to line
2 kV line to earth, 1 kV line to line
2 kV line to earth, 2 kV line to line
10 V 80% AM (1 kHz), 0.15 80 MHz
10 V 80% AM (1 kHz), 0.15 80 MHz
300 A/m, 6.4 / 16 s pulse
10 & 5 000 ms, interruption
200 ms, 40% residual voltage
500 ms, 70% residual voltage
100 V 50 Hz line to earth
250 V 50 Hz line to line
Class B
Class A
Class B
Class B
Class A
2 kVrms 50 Hz 1min
3 kVrms 50 Hz 1min
2 kVrms 50 Hz 1min (@ rated power < 60V)
40 to +70C
40 to +70C
135C (temperature class T4)
5 to 95% relative humidity
5 to 95% relative humidity
2 000 m / 70 kPa
10 year
7.5 mm, 5 8 Hz
2 g, 8 500 Hz
15 g, 11 ms
Flammability class V-1
35 x 121 x 119 mm
0.26 kg
IP 21
Convection
Horizontal on 35 mm DIN-rail
Functional description
Switches
LEDs
POWER
+VA
+VB
COM
O
V
P
Internal
Electronics
COM
STATUS
ODW-720
O
V
P
NO
C
NC
RS -232
DCD
RD
TD
SG
DSR
RTS
CTS
SHIELD
CH 1
SFP
Fibre transceiver
TX
RX
10
6651-2221
Interface specifications
Power
Rated voltage
Operating voltage
Rated current
Rated frequency
Inrush current It
Startup current*
Polarity
Redundant power input
Isolation to
Connection
Connector size
Shielded cable
ODW-720-F1:
12 to 48 VDC and 24 VAC
ODW-720-F1 Ex: 12 to 48 VDC
ODW-720-F1:
10 to 60 VDC and 20 to 30 VAC
ODW-720-F1 Ex: 10 to 60 VDC
300 mA @ 12 V
150 mA @ 24 V
75 mA @ 48 V
ODW-720-F1:
DC and 48 to 62 Hz
ODW-720-F1 Ex: DC
0.2 As
1.0 Apeak
Reverse polarity protected
Yes
RS-232 and Status port
Detachable screw terminal
0.75 2.5 mm2 (AWG 18 13)
Connect the unit using at least 18 AWG (0.75 mm2) wiring
Not required
Status
Port type
Rated voltage
Operating voltage
Contact rating
Contact resistance
Isolation to
Connection
Connector size
Shielded cable
6651-2221
11
RS-232
Electrical specification
Data rate
Protocol
Data format
Data retiming
Transmission range
Isolation to
Connection
Shielded cable
Conductive housing
*
12
EIA RS-232
300 bit/s 250 kbit/s
Asynchronous or synchronous
9 12 bits in asynchronous mode
Any type in synchronous mode
Asynchronous mode only
15 m
Status and Power port
9-pin D-sub female (DCE)
Not required, except when installed in railway applications as
signalling and telecommunications apparatus and located close
to rails*
Isolated to all other circuits and housings
To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m
boundary to the rails and connected to this port.
The cable shield should be properly connected (360) to an earthing point within 1 m from this port.
This earthing point should have a low impedance connection to the conductive enclosure of the apparatus
cabinet, or similar, where the unit is built-in. This conductive enclosure should be connected to the earthing
system of an installation and may be directly connected to the protective earth.
6651-2221
Status
screw terminal
Position
1
2
3
FX(Fibre)
(for details
see page 1213)
Description
Contact with C when fibre
optical links are in operation
Common
Open (no contact with C)
when fibre optical links are
not in operation
Product
marking
NO
C
NC
Power
screw terminal
Position
Direction*
In
2
3
4
In
In
In
Description
Common
voltage
Voltage A
Voltage B
Common
voltage
Product
marking
COM
+VA
+VB
COM
RS-232
D-sub
Position
1
2
3
4
5
6
7
8
9
Direction*
Out
Out
In
Out
In
Out
Description
Data Carrier Detect (DCD)
Received Data (RD)
Transmitted Data (TD)
Not connected
Signal Ground (SG)
Data Set Ready (DSR)
Request To Send (RTS)
Clear To Send (CTS)
Not connected
13
LED indicators
LED
Status
Description
PWR
ON
Power is on.
OFF
Power is off.
Power
FP
Not used
CH 2
Not used
CH 1
Channel 1 link status
TD
RD
FL R
Failure link remote
FL L
Failure link local
ON
Flashing
OFF
Flash
OFF
Flash
OFF
ON
Flashing
ON
Flashing
14
6651-2221
! DIP-switch settings
Before DIP-switch settings:
Prevent damage to internal electronics from electrostatic discharges (ESD) by
discharging your body to a grounding point (e.g. use of wrist strap)
Note: Disconnect power before DIP-switch settings.
S1
S2
The ODW-720-F1 DIP-switches are pre-set from the factory, so that the unit can be
used for point-to-point applications, togheter with an additional ODW-720-F1, straight
out of the box, without the need for any type of user configuration.
The only choise required, is if to enable the RTS to CTS signalling function or not.
See the DIP-switch S2:1 description below.
If the ODW-720-F1 is to be used in a multidrop network togheter with ODW-720-F2
units, please refer to the ODW-720-F2 user guide for details on how to configure the
units.
S1 DIP-switch
ON
1 2 3 4 5 6 7 8
S2 DIP-switch
ON
ON
1 2 3 4 5 6 7 8
ON
Factory default
ON
1 2 3 4 5 6 7 8
6651-2221
ON
S1
1 2 3 4 5 6 7 8
S2
15
Master
POWER
Slave
CH 1
TX
RX
POWER
CH 1
TX
RX
16
6651-2221
RS-232 interface
The RS-232 interface is a female 9-position D-sub. Pin assignments are compliance with
the EIA RS-232 standard.
Status port
The status port connects to an internal relay witch may be used to trigger an external
alarm if a fault condition occurs. During normal operation pins 1 and 2 are in contact
with each other, and pins 2 and 3 are isolated. During an optical link failure, or power
failure, pins 1 and 2 are isolated, and pins 2 and 3 are in contact with each other.
6651-2221
17
Mounting
This unit should be mounted on 35 mm DIN-rail, which is
horizontally mounted inside an apparatus cabinet, or similar.
Snap on mounting, see figure.
CLICK!
CLICK!
Cooling
This unit uses convection cooling. To avoid obstructing the airflow around the unit, use the following spacing rules. Minimum
spacing 25 mm (1.0 inch) above /below and 10 mm (0.4 inches)
left /right the unit. Spacing is recommended for the use of unit
in full operating temperature range and service life.
10 mm *
(0.4 inches)
25 mm
25 mm
Removal
Press down the black support at the top of the unit. See figure.
18
6651-2221
Sales Units
North America
info@westermo.com
www.westermo.com
Singapore
sales@westermo.com.sg
www.westermo.com
Sweden
info.sverige@westermo.se
www.westermo.se
United Kingdom
sales@westermo.co.uk
www.westermo.co.uk
Other Offices
REV. E 6651-2221 2014-10 Westermo Teleindustri AB, Sweden A Beijer Electronics Group Company