Documente Academic
Documente Profesional
Documente Cultură
GU-1130
Indice
1. Descripcin___________________________________________________________ 7
2. Funciones del panel ____________________________________________________ 9
2.1. Conexiones de entrada y salida _______________________________________ 9
2.2. Teclado _________________________________________________________ 10
2.3. LEDS ___________________________________________________________ 11
3. Rangos de medicin___________________________________________________ 11
4. Batera y recarga _____________________________________________________ 12
4.1. Descripcin de la batera. ___________________________________________ 12
4.2. Verificacin del estado de la batera ___________________________________ 12
4.3. Cargador de batera _______________________________________________ 12
4.4. Procedimiento de Carga ____________________________________________ 12
5. Reloj y calendario_____________________________________________________ 13
6. Verificacin de la calibracin del equipo ___________________________________ 13
7. Medicin de la resistencia de puesta a tierra (R PAT) _________________________ 14
7.1. Consideraciones especiales sobre la medicin de la resistencia de PAT ______ 15
8. Medicin de las tensiones espureas _______________________________________ 17
9. Medicin de Resistividad especfica del suelo por el mtodo de Wenner __________ 17
10. Indicaciones de anormalidades en el Display ______________________________ 22
10.1. Alto valor de tensin espurea _______________________________________ 22
10.2. Valor de R PAT muy alto___________________________________________ 22
10.3. Alto Valor de resistencia de las estacas auxiliares _______________________ 22
10.4. Valor muy alto de Resistividad ______________________________________ 23
11. Transfiriendo datos al ordenador PC
__________________________________ 24
11.1. Puerto de comunicacin RS-232_____________________________________ 24
11.2. Dentro de su PC _________________________________________________ 25
12. Impresora (opcional) _________________________________________________ 28
12.1. Ejemplo de impresin _____________________________________________ 28
12.2. Alimentacin del papel ____________________________________________ 28
12.3. Papel __________________________________________________________ 28
13. Especificaciones tcnicas _____________________________________________ 29
GU-1130
1. Descripcin
El telurmetro TL-5 es un instrumento digital controlado por microprocesador
que permite medir la resistencia de puesta a tierra y la resistividad especfica del
terreno (usando el mtodo de Wenner), as como tambin puede detectar las
tensiones parsitas presentes en el terreno. Este instrumento es apto para medir sistemas de puesta a tierra en subestaciones, industrias, redes de distribucin de energa, etc. de acuerdo con la IEC 61557-5. Es tambin til para la
medicin de la resistividad especfica del suelo, con el objetivo de optimizar los
proyectos de sistemas de puesta a tierra.
Antes de iniciar cada medicin el equipo verifica que todas las condiciones
estn dentro de los lmites apropiados e informa al operador en el caso de encontrar alguna anormalidad (tensiones de interferencia muy altas, resistencia de
los electrodos auxiliares muy alta, muy baja corriente, etc.). Despus, elige el
rango mas adecuado y muestra en el display alfanumrico los resultados de la
medicin.
Con el objeto de optimizar el ensayo de puesta a tierra el TL-5 permite que el
operador pueda elegir dos frecuencias para generar la corriente del ensayo
(270 Hz o 1470 Hz). En principio la frecuencia ms baja permite el anlisis del
sistema respecto de posibles falla provocadas por corrientes de maniobra (de
frecuencia industrial). Por otro lado la frecuencia ms alta muestra mejor la
influencia de las corrientes provocadas por descargas atmosfricas en los sistemas de puesta a tierra adems de ofrecer alta inmunidad a la interferencia de
las tensiones usualmente presentes en las proximidades de las subestaciones.
El instrumento tiene 4 rangos que son automticamente seleccionados cubriendo mediciones desde 0,01 hasta 20 k, lo cual permite obtener mucha precisin en las mediciones para cualquier clase de suelo.
Durante la medicin de resistividad especifica del terreno, el operador puede
introducir al equipo, las distancias entre jabalinas para aplicar la frmula de
Wenner y mostrar directamente el valor de la resistividad.
GU-1130
!
"
#
$
%
)
&
!- Terminal de salida E
"- Terminal de salida ES
#- Terminal de salida S
$- Terminal de salida H
%- Display Alphanumerico
&- Teclado
'- RS-232 puerta de comunicacin
(- Entrada alimentacin
)- Control de alimentacin del papel de la impresora PR-01(opcional)
GU-1130
2.2. Teclado
10
2.3. LEDS
:
>
<
3. Rangos de medicin
El equipo posee 4 rangos de medicin que son automticamente seleccionados
desde 0,01 hasta 20 k, como medidor de resistencia; de 0,01 m hasta
50 km como resistivmetro, y de 0 a 60 V~ como voltmetro.
GU-1130
11
4. Batera y recarga
4.1. Descripcin de la batera.
El TL-5 utiliza una batera recargable, sellada, de 12V 2.3Ah. Despus
de agotada su vida til debe ser reciclada o depositada en forma adecuada
conforme con las leyes del medio ambiente.
LOW BATTERY
[$
]}}
Battery Status
[$$$$$
]}}
Battery Status
[$$$$$$$$]}}
Charging
Battery...
Durante el proceso de carga la tecla START 7 estar desactivada.
Nota: La batera pierde parte de su carga estando almacenada. Por eso, antes de utilizar
el equipo por primera vez, o despus de algn tiempo sin uso, se debe recargar la batera.
Por cuanto el tipo de batera recargable que utiliza este equipo no presenta efecto memoria y por las caractersticas inteligentes del cargador, no hay restricciones para iniciar una
carga tantas veces como se requiera. En cuanto el cargador detecte que la batera est
completamente cargada pasar al estado de Flote en forma automtica, protegindola de
sobrecargas.
12
5. Reloj y calendario
Para facilitar la identificacin de cada medicin, el TL-5 posee reloj y calendario
internos. Fecha y hora pueden ser ajustados con un software para PC que sincroniza el reloj del equipo con el ordenador PC.
GU-1130
13
cable de 40m
Cable de
20m
Cable de 5m
D2
E3
E2
Jabalina de
corriente
E1
Jabalina de
tensin
D1
Puesta a
tierra
incgnita
a medir
Earth Resistance
3_Pole
270Hz
Esta funcin y esta frecuencia son las iniciales cuando se enciende el equipo.
(default).
Despus oprima el botn de START7.
Durante unos pocos segundos brillar el led > y luego el display pasar a
indicar el valor de la resistencia y la unidad as:
R= 10.01@
3_Pole
270Hz
14
R= 10.01@
3_Pole
1470Hz
Esta comparacin de R PAT con frecuencias diferentes permite verificar el comportamiento del sistema tanto para interferencias de maniobras como para los
efectos con descargas atmosfricas. Cada vez que se necesite cambiar la frecuencia se debe accionar primero el botn 2, (o apagar el equipo con la llave
*) para despus realizar la medicin apretando la tecla START7. Las teclas
para cambiar la frecuencia son las 1 y -.
GU-1130
15
Meseta de potencial
A
Puesta a
tierra
Zona de influencia
de la puesta a tierra
Posiciones de la
sonda E2
Jabalina de
corriente E3
Zona de influencia de la
jabalina de corriente E3
fig. 02
En general, las dimensiones de la PAT son mayores que las de la jabalina auxiliar de corriente por lo que el dimetro de su zona de influencia tambin es mayor. Por eso la sonda debe hincarse ms prxima a la jabalina de corriente que
a la PAT para cumplir la condicin requerida. Suele adoptarse una distancia del
62% como primera aproximacin. Debe tenerse en cuenta que cuando se mide
la resistencia de PAT de sistemas de gran tamao (por ej. mallas extensas de
subestaciones) se requieren distancias que pueden llegar a cientos de metros
para cumplir la condicin. La literatura tcnica describe mtodos aproximados
16
que permiten reducir esas distancias con resultados vlidos. Todas estas consideraciones se refieren a aspectos fsicos esenciales del proceso de medicin,
por lo que se aplican a todos los telurmetros, y no dependen del fabricante o la
tecnologa utilizada.
Earth Voltage
V = 1.3 V
GU-1130
ES
17
Con las teclas 34 o 56 introduzca la distancia entre jabalinas. Si las distancias elegidas fueran 1m, 2m, 4m, 8m, 16m y 32 m (que son las que generalmente se adoptan) disminuya o aumente con las teclas 34.
Si el valor fue a = 2m aparecer en el display ...
Soil Resistivity
4_Pole a= 2m
Despus oprima el botn de START7. Durante unos pocos segundos brillar el
led > y el display indicar el valor de la resistencia y la unidad as ...
# = 620 @m
4_Pole
a= 2m
Con las teclas 56 el equipo permite seleccionar distancias entre jabalinas en
pasos de 1m, y hasta sumarlos o restarlos a los valores insertos con las teclas
34.
Con las teclas 34 tambin se puede seleccionar el valor Rx
Soil Resistivity
4_Pole Rx
Esta opcin permite utilizar cualquier distancia, pero en este caso el operador
deber aplicar la frmula de Wenner, si es que utiliza el mtodo Wenner o otras
ecuaciones si se dispone a usar otros mtodos como Schlumberger, Dipolo,
Lee, etc. Tambin es til para realizar la calibracin del equipo y para introducir
los datos en algunos softwares sofisticados que permiten introducir solamente el
valor de R para el clculo de la resistividad.
18
4 Ra
=
1+
a + 4p
a + p
Donde:
= valor de la resistividad, expresado en [m]. Valor mostrado en el display.
= 3.14159
R = es el valor de la resistencia leda en el equipo usado para calcular . (Se
puede ver el valor seleccionado Rx con las teclas 3 y 4)
a = distancia entre jabalinas expresada en metros
Siguiendo este procedimiento, se obtiene el valor de la resistividad correspondiente a la capa del terreno comprendida entre la superficie y la profundidad
determinada por la distancia entre jabalinas a. La informacin requerida para
determinar la estratificacin del terreno por mtodos grficos o utilizando software especializados, se obtiene realizando conjunto de mediciones con diferentes distancias entre jabalinas. Las distancias mas comnmente adoptadas
son 1m, 2m, 4m, 8m, 16m y 32 m.
Para realizar una batera de mediciones cada vez que se deba introducir un
valor de diferentes distancias entre jabalinas, se debe oprimir primero la tecla de
. y despus fijar la distancia utilizando las teclas 3 y 4 o las 5 y 6, despus la tecla START7 (por ejemplo para a=1m; a=2m; a= 4m; se debe oprimir
la tecla 3 y luego la 7, despus la ., luego la 3 y luego la 7 y asi sucesivamente).
Luego de cada medicin, oprimiendo la tecla + se permite que los datos sean
impresos en la impresora (opcional). Durante esta operacin el LED; se
mantiene encendido.
GU-1130
19
20m cable
40m cable
20m cable
5m
cable
p
H
ES
20
b/4
a/4
a/4
b/2
b/4
a/2
GU-1130
21
y
x
fig. 05
Earth Voltage
too high!
R> 20.00k@
3_Pole
270Hz
y significa que el valor super el mximo valor de lectura del equipo.
Check H_pole
Si el valor de la resistencia de la jabalina S es muy alto el display indicar:
Check S_pole
22
# > 50k@m
4_Pole
a= 3m
GU-1130
23
24
11.2. Dentro de su PC
Entre en el men: Iniciar > Programas > Accesorios > Comunicaciones > Hiper
Terminal
Meu computador
Windows Explorer
Lixeira
Programas
Documentos
softwares
Configuraes
Pesquisar
Ajuda
Executar
Desligar
Iniciar
12:00
? X
Nova conexo
Digite um nome e selecione um cone para a conexo:
Nome:
BUILDING1
cone
OK
GU-1130
25
Cancelar
? X
BUILDING1
Pas/regio:
Brasil (55)
Cancelar
? X
4800
8
Nenhum
1
Nenhum
Avanadas
Restaurar padres
OK
Cancelar
26
Aplicar
Sending Data
Wait...
Los datos de la memoria estarn disponibles para visualizacin y almacenamiento en el ordenador.
Las informaciones transmitidas tendrn el formato siguiente:
Hyper Terminal
GU-1130
27
12.3. Papel
Lado blanco
Lado amarillo
28
: Medicin de resistencias de puesta a tierra (con 3 bornes), resistividad especfica del suelo (con 4 bornes) y
tensiones presentes en el terreno. De acuerdo con la
norma IEC 61557-5.
Mtodo de medicin de
resistencia de puesta a
tierra
Mtodo de medicin de la
resistividad especfica del
terreno
Frecuencias de operacin
: 270 Hz 1 Hz o 1470 Hz 1 Hz
Voltmetro
Rangos de medicin
Exactitud
Resolucin de lectura
Corriente de salida
GU-1130
29
Inmunidad respecto a la
interferencia de tensiones
espureas
Resistencias de tierra de
las jabalinas auxiliares
Funciones avanzadas
Impresora PR-01 (opcional) : Permite imprimir los resultados para ser registrados como
documento.
Alimentacin
Cargador de batera
Seguridad
: Cumple los requerimientos de la norma IEC 610101/1990, IEC 61010 1/1992 anexo 2
Inmunidad electrosttica
30
Altitud mxima
: 3.000m
: -25C a 65C
Dimensiones
Accesorios incluidos
GU-1130
31
Apuntes
32
TL-5
Microprocessor Controlled Digital Earth Tester
Users Guide
GU-1130
33
Index
1. Description __________________________________________________________
1.1. Control panel_____________________________________________________
1.1.1. Connections and items _________________________________________
1.1.2. Keyboard ____________________________________________________
1.1.3. LED's _______________________________________________________
1.2. Measurement ranges ______________________________________________
2. Battery / battery charger________________________________________________
3. Real time clock and calendar ____________________________________________
4. Equipment calibration checking __________________________________________
5. Grounding resistance measurement ______________________________________
5.1. Observations about grounding diffusion systems (GDS) ___________________
6. Spurious voltages measurement _________________________________________
7. Soil resistivity measurement ____________________________________________
8. Abnormalities indications on the display ___________________________________
8.1. Excessively high spurious voltages____________________________________
8.2. Excessively high earth resistance _____________________________________
8.3. Excessively high resistance in the auxiliary rods _________________________
8.4. Excessively high soil resistivity _______________________________________
9. Exporting data to the computer __________________________________________
10. Printer (optional)
_________________________________________________
11. Technical Specifications_______________________________________________
34
35
36
36
37
38
38
39
40
40
41
42
43
43
46
46
46
46
47
47
48
49
1. Description
The TL-5 is a microprocessor controlled earth tester that allows measuring earth
resistance and ground resistivity (by Wenner's method), as well as detecting
parasitic voltages that may be present in the ground. Totally automatic and easy
to operate, the TL-5 is suitable to measure earth systems in power substations,
industries, distribution networks, etc., according to IEC 61557-5, or to measure
soil resistivity in a terrain, in order to optimize the earth systems project.
Before starting each test, the TL-5 will check if all conditions are within the appropriate limits and will notify the operator if there are any abnormalities, such as
too high interference voltage, too much resistance in the test spikes, very low
test current, etc. If all conditions are normal, the equipment will automatically
select the adequate range and will show the results on the display.
In order to conveniently test earth systems, the TL-5 allows measurements using
test currents with selectable frequency, of 270Hz or 1470Hz. Measurements in
the 270Hz frequency allow to analyse the system behaviour when in contact with
fault currents of industrial frequency, while those in the 1470Hz frequency show
better the system behaviour when in contact with electrical currents caused by
lightning. Measurements in the higher frequency also offer high immunity to
interference voltages in the soil, what allows accurate results in often unfavorable conditions.
The TL-5 has memory to store up to 4000 measurements, a built-in printer (optional)
and a serial data output that allows to transfer the stored results to a computer or
data-logger for later analysis. Practical, lightweight and strong, the TL-5 is suitable to
field use, even under severe weather conditions. It is powered by a rechargeable
battery (220 - 240V charger), and is supplied with all the necessary accessories
in a practical auxiliary case.
GU-1130
35
'
!
"
#
$
%
)
&
!- Output terminal E
"- Output terminal ES
#- Output terminal S
$- Output terminal H
%- Alphanumeric display
&- Keyboard
'- RS-232 communication port
(- Power supply input
)- Paper feed control (only with optional printer)
36
1.1.2. Keyboard
/
4
6
+ ,
- .
*- ON/OFF switch
+- The printer is active
,- Activates the voltmeter
-- Selects 270Hz frequency
.- Selects the resistivity measurement function
/- Shows the battery charge status on the display
0- Sends stored memory data to a connected computer or data logger
1- Selects 1470Hz frequency
2- Selects the resistance measurement function
3 and 4- Increase or decrease the specified distance between rods in a progression of 1, 2, 4, 8, 16 or 32 meters. It also allows the operator to select the Rx
function, used to check the equipment calibration by using a standard resistance
(ignoring the distance parameter, not needed in this function)
5 and 6- Increase or decrease the specified distance between rods in one
meter steps.
7- START key; starts the test.
GU-1130
37
1.1.3. LED's
9
:
>
<
38
LOW BATTERY
[$
]
When connected to the power supply, the battery charger will be always active,
even if the TL-5 is off.
Recharge procedure:
Check if the TL-5 is off, and then connect it to the power supply. The battery
charger LED will turn red, and will remain so until the battery is totally recharged.
Then, the light will turn to green, and will stay on until the equipment is disconnected from the power supply.
If the equipment is turned on during the recharge procedure, the display will
show:
Charging
Battery...
During the process, the START7 key will be deactivated.
Note: battery slowly loses part of its charge while stored, even whitout use.
Therefore, before using the equipment for the first time, or after a long period out
of use, it may be necessary to recharge the battery.
GU-1130
39
40
40m cable
20m cable
5m cable
D2
E3
E2
Current
rod
E1
Voltage
rod
Ground
to be
measured
D1
Press the START7 key to start the test. The test number will be shown on the
display, followed by the message WAIT..., and after a few moments the resistance value will appear, as in the following example:
R= 10.01@
3_Pole
270Hz
The result will then be stored on the memory.
GU-1130
41
Potential plateau
A
Ground
diffusion
resistance
Ground diffusion
resistance influence
area
Voltage Rod E2
measurements
points
Current Rod E3
influence area
42
Current
Rod E3
Generally, GDS dimensions are greater than those of the auxiliary current rod,
thus its area of influence diameter is also greater. So, in order to comply with the
required condition, the probe must be set up closer to the current rod than to the
GDS. A distance of 62% is usually adopted as a first try. It should be noted that
when measuring GDS resistance in large systems (such as a large grid that
underlies a substation) distances of hundreds of meters are required to fulfil the
condition. Technical literature describes alternative methods that make it possible to reduce those distances with valid results.
Note: all these observations refer to physical aspects essential to the measurement
process, being applied to all earth meters, regardless of manufacturer or technology.
Earth Voltage
V = 1.3 V
To select the resistivity measurement function, press the (.) key. Insert four
rods in the ground, well aligned and with an equal distance from each other.
Connect them to the output terminals using the supplied cables. Remember that
the distance between rods is very important when measuring soil resistivity,
since this value is part of the calculation.
GU-1130
43
Specify the distance between rods (a in the image below and on the display) by
using the 3 and 4 keys (5 and 6 to increase or decrease only one meter at a
time).
fig. 03
ES
Press the START7 key. The TL-5 will automatically apply Wenner's equation
(below) based on collected data.
4 Ra
=
1+
a + 4p
a + p
Legend:
= soil resistivity value; will be shown on the display
a= distance (in meters) between rods; specified by the operator
p= insertion depth (in meters) of the rods the TL-5 uses 0,5m
R= resistance value used by the equipment to calculate
The display will then show the soil resistivity value, as in the example below:
# = 620 @m
4_Pole
a= 2m
44
To properly evaluate soil resistivity, measurements must cover the whole area to
be influenced by the grounding system. For an area of up to 10.000m, it is recommended to perform measurements in at least five points, arranged as shown
in the image below. Two sets of measurements should be needed for the central
point.
b/4
a/4
a/4
b/2
b/4
a/2
y
x
Larger areas can be divided in areas of 10,000m each. In the case of different
forms, limiting the area in smaller rectangles is a possible and practical solution.
GU-1130
45
Earth Voltage
too high!
R> 20.00k@
3_Pole
270Hz
Check H_pole
The reason may be a wrong connection or excessive high-diffusion resistance
on the H pole. Check the installation to correct the problem.
46
If resistance on the S pole is too high or if there is a disconnection near the pole,
the display will show:
Check S_pole
Either resistance diffusion on the S pole may be excessively high, or there is a
disconnection nearby. Check the installation to correct the problem.
In both cases, if the problem is being caused by excessive resistance, watering
the rods or inserting several interconnected rods may reduce the resistance,
allowing measurements to take place correctly.
# > 50k@m
4_Pole
a= 3m
GU-1130
47
The computer is now correctly configured to receive data from the equipment.
Press the MEM key and the TL-5 will send all stored data to the computer, while
the display shows the following message:
Sending Data
Wait ...
Memory data will then be available to visualization and archiving in the computer.
White side
Yellow side
48
Resistance measurement
method
Operation frequency
Resistivity measurement
method
Voltmeter
Measurement ranges
: Resistance: 0 - 20 k (autoranging)
Accuracy
Reading resolution
Output current
Immunity to spurious voltage : During the R measurement, it allows for the presence
of spurious voltage up to 7 V~
interference
GU-1130
49
Advanced Features
Power supply
Battery charger
Safety Class
E.M.C
Electrostatic immunity
Altitude Maximum
: 3000m
Operation temperature
: -10C to 50C
Storage temperature
: -25C to 65C
Humidity
Equipment weight
Size
Included Accessories
GU-1130
51
Notes
52
Notes
GU-1130
53
Notes
54