Documente Academic
Documente Profesional
Documente Cultură
Abstract: In order to ensure uniform style throughout the proceedings of the National Geofest, all the papers need
to be prepared very strictly according to the instructions set in this template. The paper size should be A4 (210mm
x 297 mm). The abstract should be brief and it should consist of only one paragraph giving a concise summary of
the material in the paper below. You can delete the sample text in this template to conveniently replace it with text
of your own contribution to the proceedings. However it is recommended that you keep an initial version of this
file for reference. Please replace the author names (above) affiliations and addresses with your own and co authors
names, affiliations and addresses. Email addresses must be provided as footnotes on the first page as shown.
Keywords: Please provide no more than 5 keywords interspaced with a comma.
1. Introduction
All papers must be written in English. SI-units
should be used. The full paper should not exceed ten (10)
pages. The academic supervisor of each participating
group must submit the groups technical paper together
with his /her completed feedback form by email to
National Geofest Secretariat on or before 3 rd
November 2014 in MS WORD. A hardcopy of the paper
and any substantiating referencing documents, A0 size
poster and model must be brought to the UTHM
preferably on the 5th November evening.
Please set your page size of the technical paper as
standard A4. The top and bottom margins should be set at
3 cm each; Left and right margins at 2 cm each. The
header should be set at 1.5 cm and the footer at 2 cm. The
text should be set in 10 pt Times New Roman with
single line spacing. The title of the paper must be set in
18 pt Times New Roman, boldface, mixed case as in
this template. Sub-headings must be set in 12 pt Times
New Roman boldface [2-5].
Authors names are set in 14 pt Times New Roman
boldface, mixed case. Affiliation details need to be set in
10 pt Times New Roman, mixed case. Figures and Table
captions must also be set in 10 pt Times New Roman
mixed case.
k
T 2 T c p
cp
c
p
N
N
1
1
Y Vi hi
i hi
c p i 1
c p i 1
T
(1)
3. Tables
The tables are best designed to have a uniform style
throughout the paper. Again it is best if tables too are
preferably located at the top or bottom of a page where
they are first cited (see Table 1). The caption heading for
a table should be placed above the table as illustrated
V.K. Sahu et al., Int. J. Of Integrated Engineering Vol. 3 No. 1 (2011) p. 1-4
References (examples)
i.
Fig. 1 Computational domain with boundary types.
Table 1 Numerically obtained maximum flame
temperature for different fuel mass fraction and air
temperature at constant strain rate a2=300 s-1 and
adiabatic flame temperature for corresponding reaction.
Fuel mass
fraction
(YF,1)
Temperature of hot
air T2 (K)
0.1
0.3
0.5
0.8
1340
1230
1215
1200
Maximum
flame
temperature (K)
1880
2364
2627
2735
Adiabatic
Flame
temperature (K)
1908
2541
2740
2882
4. Use of colours
Since the National Geofest proceedings may be
published in an electronic form, the use of colours in the
figures is free and encouraged. Nonetheless, please be
certain that colour illustrations are meaningful, looks
good and will make sense even in grayscale. All authors
must testify that their tables and figures are their own
works; previously published figures must be source
referenced and needs to be accompanied by a written
permission from the author and publisher. Very large
figures and tables should be placed on a page by
themselves.
Acknowledgements that you wish to make to funding
bodies etc, may be placed in a separate section at the end
Published
by UTHM Publisher
2
http://www.uthm.publisher.edu.my/ojs/ijie