Documente Academic
Documente Profesional
Documente Cultură
XC Trail Configurations
Objectives
j
Review the p
process of configuring
g
g XC trails in the IP-10 G-Series
indoor unit using basic scenarios
Verify process is clear and understood per participant
Before we start
In this presentation we will be using the following figures:
Pipe
3
MNG(slot#1)
XC Trails Guidelines
1. XC Trails can be configured only via Main unit
2 When Protection is enabled
2.
enabled, configure trails to go via the Active unit
(XC Trails are automatically created on the STBY unit)
1. T-Cards (TDM / SDH) are not hot-swappable, do not extract / insert card when IDU
is powered up
2. Radio VCs must be identical on both sides of the radio link
3 XC Trails can be configured between:
3.
Radio to Line
Line to Radio
Radio to Radio
Sit #2
Site#2
Pipe(slot#3) 3
MNG(slot#2)
7
Pipe(slot#3)
MNG(slot#2)
3
MNG(slot#1)
MNG(slot#1)
Site #1:Line p
port 1, Radio VC #1
Site
S
e#
#2: Line
e po
port 1,, Radio
ad o VC
C#
#1
Scenario #1 Configuration
g
using
g EMS
Launch EMS
Click on Active unit, make sure it is selected
Note that the T-cards show no alarms
Scenario #1 Configuration
g
using
g EMS
Expand
p
the Configuration
g
section in the main navigation
g
menu
Expand the Trail section
Click on TDM Trails
Scenario #1 Configuration
g
using
g EMS
1.
2.
Scenario #1 Configuration
g
using
g EMS
Scenario #1 Configuration
g
using
g EMS
10
Site#2
3
Pipe(slot#2)
p (
)
Pipe(slot#2)
p (
)
3
MNG(slot#1)
MNG(slot#1)
Radio VC #17
Site#1
Radio VC #17
3
Pipe(slot#2)
MNG(slot#1)
Radio VC #17
11
Radio VC #17
Scenario #2 Site
#1 configuration
g
Site#2
3
MNG(slot#1)
MNG(slot#1)
Radio VC #17
Site#1
3
Pipe(slot#2)
MNG(slot#1)
12
Pipe(slot#2)
p (
)
3
Scenario #2 Site
#2 configuration
g
R di VC #2
Radio
Site#3
Site#2
3
Pipe(slot#2)
p (
)
Pipe(slot#2)
p (
)
3
MNG(slot#1)
MNG(slot#1)
Radio VC #17
Site#1
Radio VC #17 was chosen to transport the TDM traffic via the link
3
MNG(slot#1)
We create a protected patch,
therefore we need to select a 3rd interface: Slot #2
13
Scenario #2 Site
#3 configuration
g
R di VC #2
Radio
Radio VC #2
Site#2
3
Site#3
3
Pipe(slot#2)
p (
)
Pipe(slot#2)
p (
)
3
MNG(slot#1)
MNG(slot#1)
Radio VC #17
Radio VC #17
Site#1
Make sure you use the same the Trail ID via the paths.
14
Trail Configuration
g
using
g CLI
All the trail can be configured using CLI interface.
Ceragon has also developed a simple tool in Excel to help customer to provide remote
support in trail configurations.
All the trails can be configured in the Excel sheet and then just be pasted in the CLI
interface of IP-10.
15
Summaryy
We configured XC trails in a simple protected link
We configured protected XC Trails in a Ring topology
You can know use these 2 scenarios as a reference for additional cases
Always remember to review the XC Trails guidelines before you configure your setup
16
Thank You !
training@ceragon.com
17