Documente Academic
Documente Profesional
Documente Cultură
Introduction
Welch Rietschle
Thomas Rotary
Vane Pump
Due to their high flow, deep vacuum capability oil-sealed rotary vane pumps have traditionally been very
popular in laboratories as they are capable of handling most pumping requirements. However, due to the
fact that vapour will condense in the pump, careful selection of traps, accessories and diligent
maintenance is required to ensure trouble-free use.
Not all tasks or experiments within the laboratory need high flow and deep vacuum and there are
alternative pumping technologies that may be more suitable. Please talk to our Technical Office on
01342 826836 if you require assistance.
Diaphragm pumps
These are oil-free pumping mechanisms available in two forms, one for pumping air and one for
pumping chemicals. A typical use of a chemical version would be for rotary evaporation.
Piston pumps
These are oil-free pumping mechanisms that generally have a higher compression ratio than diaphragm
pumps, and provide good flow characteristic when used in such applications as filtration, cell harvesting
and vacuum oven drying. Not suitable where aggressive vapours or solvents are involved.
Scroll pumps
A sophisticated oil-free design that gives high flow rates and deep vacuum of the same order as rotary
vane pumps. Your application may require the use of a chemical trap.
Please consult your Safety Officer regarding the location of your pump and the management of exhaust
fumes, especially if handling aggressive chemicals.
Pump selection - our rule of thumb guide for you. If you are in any doubt please contact our Technical
Office on 01342 826836 for assistance.
1. Select appropriate approximate vacuum for the application
2. Is chemical resistance required (yes or no)?
3. Select flow rate if appropriate. Approx flow rate should be 12 times the volume to be
evacuated (litres per min) except for filtration, where there the system is not gas tight, use x4.
Examples: a. Rotary evaporation of 5L flask plus condenser plus tubing (probable 12L in total),
therefore =12x2=24L/min pump flow rate:
b. Vacuum oven of 50L capacity 50x2=100 L/min pump flow rate:
c. Filtration of 4x1L flasks on manifold plus tubing (probable 5L in total), therefore
5x4=20L/min pump flow rate.
4. Do not ignore features for ease of handling i.e. catchpot, gauge etc
5. Add accessories to increase pump life
Application
Filtration
Desiccation
Aspiration
Cell harvesting
Rotary evaporators
Rotary evaporators
Gel dryers
Centrifugal evaporators
Centrifugal evaporators
Freeze dryers
Vacuum manifolds
Vacuum ovens
Glove boxes
Transfer chambers
100~300 mbar
100~300 mbar
100~300 mbar
100~300 mbar
10 mbar
2 mbar
50 mbar
10 mbar
2 mbar
0.1 mbar
2 mbar
10 mbar
10 mbar
10 mbar
80% solvents
95%+ solvents
Too deep vacuum or too high flow rate cracks gels
80% solvents
95%+ solvents
Bigger is not better as too large a vacuum pump tends to increase the likelihood of condensable vapours bypassing
the cold trap and migrating into vacuum pump oil. For instance, a -55C system condenser will not condense out
Acetonitrile vapour causing vapour to condense in oil.
747
Pumps
Mityvac, Hand-operated Vacuum Pumps
521-003
Hand-held, durable vacuum pumps. Quick and easy to use, with only one hand required to operate and
release vacuum. External vacuum release valve eliminates need to disengage pump from the line. Nozzle
fits standard 6mm i.d. tubing. Both models have a pump rate of 16cm3/stroke and attain a vacuum of up
to 409cm3 of mercury in a few seconds. Models have PVC body.
Cat. No.
Description
Price
POA
POA
520-003
Description
Price
POA
520-002
520-001
Will operate effectively (half vacuum) at a flow rate of 7 litres per minute
Description
Price
POA
POA
The unit is based on the well established Boxer 3000 range of pumps. It has been specially designed as
a flat package to compliment any laboratory shelf, and can be operated in any orientation.
The pump operates on 12V DC and being a low voltage pump, is safe to operate in most laboratory
environments. The unit is supplied with a switch mode power supply. This power supply can be used in
any supply voltage from 110V to 240V. Air flow can be adjusted via the selectable voltage switch on the
remote power supply.
New
The 3300P pump can be easily fitted with the filter and silencer which are offered as economical, semidisposable accessories.
Maintenance free
Quiet operation
Specification
Maximum flow rate, m3/hr (L/min)
Maximum vacuum, mbar
Maximum pressure, mbar
Dimensions (hxwxd), mm
Weight (including power supply), kg
Electrics
Cat. No.
1.2 (20)
400
650
61x155x222
1.7
230V AC to 110V AC
Description
521-019 Boxer 3300P Compact air and gas pump supplied with
power adaptor and a range of plugs
521-020 Air filter and silencer
748
Price
POA
POA
Pumps
Charles Austen
521-061
New
521-063
New
521-064
New
The Capex 8C is ideal for continuous duty as either a vacuum pump or compressor. It has a compact yet
rugged aluminium case with a flush-folding carry handle and built in cable tidy. It incorporates unique Tslot rails for quick and easy mounting of retrofittable accessories such as collection flasks and vapour traps.
Suitable for applications such as vacuum and pressure assisted filtration and sampling
Specification
Flow rate, m3/h (L/min)
Maximum vacuum, mbar
Maximum pressure, bar
Dimensions (hxwxl), mm
Weight, kg
Cat. No.
0.48 (8.0)
240
2.0
214x137x282*
3.75
Description
Price
POA
Up to 5.0L/min flow
Easy to maintain
Quiet operation
Specification
3
0.3 (5.0)
500
0.8
2800
Dimensions (hxwxl), mm
Weight, kg
Standards
125x151x210
2.1
IEC 1010
Description
Price
POA
POA
Specification
Model
Maximum free flow rate, m3/h (L/min)
Maximum vacuum, mbar
Maximum pressure, bar
Speed, rpm
Dimensions (hxwxl), mm
Weight, kg
Standards
Cat. No.
Innovac 20
1.2 (20)
8.0
1.0
1400
214x136x331
8.5
IEC 1010
Description
Innovac 40
2.3 (38)
8.0
1.0
1400
214x136x393
11.6
IEC 1010
521-103
521-102
Price
POA
POA
749
Pumps
Fluid Aspiration
New
521-187
Lid with integrated fine filter casing with quick release bayonet joint
Hose connection via quick fit coupling with bi-directional shut-off valve
BIOVAC 102 - Stand alone fluid aspiration system, ready for use, comprising: Diaphragm pump, glass
catch-pot, hand set, foot switch and carry handle.
Specification
Flow rate, m3/hr (L/min )
Ultimate pressure, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
Cat. No.
12
<100
330x170x370
8
230V, 50/60Hz
Description
Price
POA
For details on accessories, including maintenance kits, please contact our Technical Office on 01342 826836.
New
521-015
Self-priming
Specifications
Model
Flow rate, l/min
Max suction head, mWg
Max pressure head, mWg
Dimensions (mm)
Weight, kg
750
NF100 KT.18 S
0.2-1.3
4
10
130x99x177
1
NF1.100 KT.18 RC
0.2-1.3
4
60
130x99x177
1
NF300 KT.18 S
0.5-3.0
3
10
160x104x188
1.5
Cat. No.
Description
521-015
521-016
521-017
521-018
NF1.300 KT.18 RC
0.5-3.0
3
60
160x104x188
1.5
Price
POA
POA
POA
POA
Pumps
Fluid Aspiration
521-179
Simple, safe and easy to use vacuum aspiration system, specifically designed for fluid aspiration from
bulk samples to microplates in chemistry, biochemistry, biology and medicine.
Automatically controlled, low maintenance, high performance vacuum pump with condensate catchpot
on exhaust provides vacuum automatically on demand for single and multiple workstations, with no
need for foot pedal or start / stop switch. This ready-to-use unit comes complete with an ambidextrous,
ergonomically designed hand control, which accepts all common pipettes and tips, and a large 4 litre
autoclavable collection bottle (with additional port for second hand control) and biohazard filter. It is
also available without pump (BVC01) for connection to existing vacuum systems.
BVC21 - Stand alone fluid aspiration system, ready for use unit comprising vacuum pump, vacuum
control, collection bottle/filter, hand set.
BVC01 - Fluid aspiration system without pump for connection to existing vacuum system
Easy to use
521-180
Specifications
Model
Dimensions (lxwxh), mm
Weight, kg
Electrical supply
Cat. No.
BVC21
520x300x500
11.0
230V, 50/60Hz
BVC01
300x250x500
4.0
230V, 50/60Hz
Description
Price
POA
POA
Accessories
Cat. No.
Description
521-181
521-183
521-182
521-186
521-184
521-185
Price
POA
POA
POA
POA
POA
POA
691-057
This dry vacuum aspiration system is specifically designed for fluid aspiration from bulk samples to
microplates in biochemistry, biology, chemistry and medicine. This ready to run unit is supplied complete
with autoclavable collection vessel, footswitch, pipette holder, 1.8m tubing, vacuum regulator and gauge.
Cost effective
Quiet operation
Specification
Flow rate, m3/hr (L/min)
Maxiumum vacuum, mbar
Capacity plastic autoclavable bottle, ml
Tubing required, I.D., mm
Dimensions (wxdxh), mm
Weight, kg
Cat. No.
34 (2)
560
1200
6.35
375x210x255
4.9
Description
Price
POA
Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342 826836.
For replacement silicone pipette holder and tubing, please contact our Technical Office on 01342 826836.
751
Pumps
Fluid Aspiration
New
521-400
A strong vacuum created by pumping water through two or four Teflon Venturi jets
No oil needed
Specifications
Model
Bath material
Air flow, L/min
Bath volume, litres
Dimensions (wxdxh), mm
Weight, kg
Power consumption, W
Cat. No.
UNIJET I, 2 jets
without vacuum pressure control
clear plastic
28
8
250x370x400
8.5
160
UNIJET I, 4 jets
with vacuum pressure control
plastic
35
8
250x370x400
8.5
160
Description
Price
521-400 UNIJET I aspiration pump with 2 jets without vacuum pressure control.
Supplied with non refrigerated water bath, analogue vacuum gauge.
521-401 UNIJET I aspiration pump with 4 jets with vacuum pressure control.
Supplied with non refrigerated water bath, analogue vacuum gauge.
New
521-403
POA
POA
Specifications
Model
Bath material
Air flow, L/min
Residual pressure @4C, mbar
Bath volume, litres
Dimensions (wxdxh), mm
Weight, kg
Power consumption, W
Cat. No.
Description
521-402 UNIJET II aspiration pump with 2 jets without vacuum pressure control.
Supplied with 10 litre refrigerated water bath, digital display for temperature,
vacuum gauge and dual vacuum pipe.
521-403 UNIJET IV aspiration pump with 4 jets with vacuum pressure control.
Supplied with 10 litre refrigerated water bath, digital display for temperature,
vacuum gauge and dual vacuum pipe.
752
Price
POA
POA
Pumps
Welch Rietschle Thomas
691-041
The Welch Rietschle Thomas GelMaster is a patented vacuum system with room
temperature vapour trap and vacuum system integrated into a single, high-efficiency,
low-maintenance unit.
The vapour trap reduces the overall vapour load enabling a compact, high-efficiency
diaphragm pump to be the primary vacuum force.
Trapped fluids accumulate in the collector over 10 to 15 gel drying runs (and it is just
as efficient on the last run as on the first). When the fluid reaches the red zone in the
fluid-level sight glass, simply open a valve and drain the collected fluid. The system is
then ready to dry more gels. The trapping fluid can then be re-used over and over
again, since it does not mix with the condensate.
The diaphragm pump delivers a powerful, non-fluctuating vacuum for fast,
smooth drying.
Specifications
Condensed vapour capacity, litres
Inlet port
Dimensions (wxdxh), mm
Weight, kg
Cat. No.
1.5
10mm ID hose nipple
286x394x365
15.2
Description
Price
POA
Please note: 100 and 115V versions are available. Please contact our Technical Office on
01342 826836.
691-056
Welch Rietschle Thomas dry piston pumps are ideal replacements for oil sealed pumps
for general utility applications such as drying and degassing. These compact pumps
are built for extended service life and are supplied with accessories for ease of use.
Carrying handle, suction-cup feet, power cord, on/ off switch, regulator, gauge and
trap are included. Suitable for use with:
Vacuum ovens
Transfer lines
Specifications
Model
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Maximum pressure, mbar
Motor, HP
Tubing required, I.D., mm
Dimensions (lxwxh), mm
Weight, kg
2561
3.0 (50)
4
6.7
1
3
10
439x165x267
9.7
2581
4.9 (83)
4
6.7
1
3
10
432x191x305
13.4
Cat. No.
691-055
691-056
Price
POA
POA
Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342
826836.
753
Pumps
Welch Rietschle Thomas
New
691-048
New
691-049
Vacuum regulator
Self-cleaning purge extends pump life but does not interfere with vacuum
The glass inlet separator helps protect the pump from ingesting liquids or particles. The gas ballast or
vent switch acts to minimise vapour condensation when pumping heavy vapour loads. Vacuum
regulation is accomplished with an adjustable bleed valve.
Any particles, water or condensed vapour that may have been ingested into the pump are purged when
it is shut off. The self-cleaning purge automatically turns on for 2 minutes after turning off the pump. An
exhaust separator catches any liquid or particles during the purge cycle.
Specifications
Model
Vacuum, mbar
Flow rate, m3/hr (L/min)
Gauge
Motor, HP
Tubing required I.D., mm
Dimensions (lxwxh), mm
Weight, kg
Cat. No.
2023
10
1.62 (27)
dial
1
5
7
324x203x292
12.7
2027
2
1.62 (27)
digital
1
5
7
324x203x292
12.7
Description
Price
691-048 Model 2023 automated dry vacuum system supplied with power cable and
operating manual with applications advice
691-049 Model 2027 automated dry vacuum system supplied with power cable and
operating manual with applications advice
New
691-051
POA
POA
Oil-free
Quiet operation
Specifications
Model
Ultimate vacuum, mbar
Flow rate, m3/h (L/min)
Motor, HP
Tubing required, I.D., mm
Dimensions (lxwxd), mm
Weight, kg
Cat. No.
2021
2.7
1.1 (18)
1
5
7
254x254x175
9.1
2031
2.7
1.6 (27)
1
5
7
254x254x175
9.1
Description
691-050 Model 2021 self-draining teflon pump supplied with power cable and silencer
691-051 Model 2031 self-draining teflon pump supplied with power cable and silencer
Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342 826836.
754
Price
POA
POA
Pumps
Welch Rietschle Thomas
691-042
New
691-054
New
Welch Rietschle Thomas dry-piston vacuum pumps are ideal for air sampling, pressure/ vacuum filtration,
water aeration, flame photometers etc. The units are built for continuous-duty operation with low noise
and a service life that exceeds diaphragm pumps.
Regulators and gauges make it easy to meet your vacuum and pressure requirements. Discharge air is
filtered and noise is muffled with a filter. A moisture trap keeps water from being accidentally drawn
into the unit.
All wetted aluminium parts are treated for corrosion protection from moisture. All other wetted parts are
stainless steel. The motor is thermally protected. Carrying handle, suction-cup feet, power cord, on/
off switch, regulator, gauges and traps are included.
NB; These pumps are not recommended for pumping acid, base or organic vapours.
Pressure regulator
Continuous-duty operation
Vacuum regulator
Quiet operation
Compact
Specifications
Model
Flow rate, m3/hr (L/min)
Maximum continuous pressure, bar
Maximum vacuum, mbar
Typical filter funnel capacity
Motor, HP
Tubing required, ID., mm
Dimensions (lxwxh), mm
Weight, kg
Cat. No.
2522
1.1 (18)
2
133
1-2
1
8
7
205x224x254
5.3
2534
1.7 (28)
2
90
1-4
1
8
7
205x224x254
5.3
2546
2.3 (38)
2
80
1-6
1
8
7
205x224x254
5.3
Description
Price
POA
POA
POA
Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342 826836.
Quiet operation
Specifications
Model
Well system
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Maximum pressure, bar
Motor, HP
Tubing required, I.D., mm
Dimensions (lxwxh), mm
Weight, kg
Cat. No.
2585
256
10.2 (168)
80
1
1
3
10
282x234x279
11.6
2567
96
4.9 (83)
80
1
1
3
10
150x254x254
7.5
Description
Price
POA
POA
Please note: 100 and 115V versions are available. Please contact our Technical Office on 01342 826836.
Aspiration of buffer solutions during cell harvesting is permitted, but do not allow liquids to be ingested into the
pump. Not recommended for pumping acid, base, organic vapours or gases.
755
Pumps
Welch Rietschle Thomas
691-035
The W-Series pumps from Welch Rietschle Thomas are oil-lubricated, rotary vane high-vacuum pumps
suitable for use with freeze dryers, centrifugal concentrators and vacuum ovens.
Model 8917-80 is supplied with a built-in large capacity acid neutralisation filter which will lead to an
extended service interval. The acid neutralisation filter is designed for use with TFA, TFA by-products
and acetonitrile.
691-047
Cool running - special interstage fan delivers improved seal life, reliability and lengthens the time
between oil changes
Easy oil-change valve - with a simple turn, spent oil is neatly directed into a beaker for inspection
or a bottle for recycling. A tube can be attached for remote collection.
Unibarb hose connections to eliminate need for expensive clamps and flanges
Quiet operation
Compact
Specifications
Model
Ultimate vacuum gas
ballast closed, mbar
Ultimate vacuum gas
ballast (fully open), mbar
Flow rate, m3/hr (L/min)
Nominal pumping
speed, m3/hr (L/min)
Motor, HP
Pump speed, rpm
Inlet connection
Tubing required, I.D., mm
Oil capacity, litres
Noise level , dB(A)
Surface temperature rise, C
Dimensions (wxdxh), mm
Weight, kg
691-036
Cat. No.
New
756
691-037
8907
1.3x10-4
8912
1.3x10-4
8917
1.3x10-4
8917-80
1.3x10-4
80
60
40
40
3.4 (56)
3.2 (53)
5.2 (86)
4.8 (80)
8.4 (138)
7.6 (125)
8.4 (138)
7.6 (125)
1
3
1425
Unibarb
11, 20
1.15
<50
20
165x471x243
18
1
3
1425
Unibarb
11, 20
1.08
<50
20
165x471x243
18
1
3
1425
Unibarb
11, 20
1.38
<50
20
165x471x243
22
1
3
1425
Unibarb
11, 20
2.5
<50
20
292x471x243
24.4
Description
691-033 Model 8907 high-vacuum pump supplied with unibarb inlet fitting,
power cable and 1L oil
691-034 Model 8912 high-vacuum pump supplied with unibarb inlet fitting,
power cable and 1L oil
691-035 Model 8917 high-vacuum pump supplied with unibarb inlet fitting,
power cable and 1L oil
691-047 Model 8917C-80 high-vacuum pump supplied as above, but also with
built-in large capacity acid neutralisation filter
Accessories
691-037 Exhaust oil recycler. Designed for pumping continuously at high pressure for
prolonged periods
691-036 Exhaust filter. Designed for intermittent deep vacuum use
691-043 Dry ice/liquid nitrogen trap
691-045 Molecular sieve trap
691-046 Replacement filter element for 691-036
691-038 5 litre Directorr Premium vacuum pump oil
Price
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
Pumps
Edwards
520-022
The RV series pumps are unique in their capability to deliver high or low throughputs with high ultimate
vacuum, which combined with ultra-low noise levels makes them ideal for a wide range of applications
and environments. They also feature a fast acting inlet valve to seal the pump for suck-back protection.
The pumps are easy to install, use and maintain. All the controls are clearly marked and have large finger
grips for ease of use. Inlet and outlet are both fitted with standard NW25 flanges. Supplied with 1 litre
of Ultragrade 19 oil. Power cord is required but not included with the pumps. For Health and Safety
requirements an oil mist filter is required (see below).
Specifications
Model
Pumping speed, m3/h (L/min)
Displacement, m3h1
Ultimate vacuum, mbar
Noise, dB(A)
Max. water vapour
pumping rate gh1
Oil capacity, L
Dimensions (wxdxh), mm
Weight, kg
RV3
3.3 (55)
3.7
2x103
48
RV5
5.1 (85)
5.8
2x103
48
RV8
8.5 (140)
9.7
2x103
48
220
0.7
158x430x224
21.6
220
0.7
158x430x225
21.5
220
0.75
158x470x261
26.0
Cat. No.
520-022
520-023
520-024
Price
POA
POA
POA
520-022 DETAIL
Accessories
Cat. No.
Description
Price
POA
POA
691-021
Specifications
Pumping speed, m3/h (L/min)
Displacement, m3/h (L/min)
Ultimate vacuum, mbar
Without gas ballast
With gas ballast
Vacuum inlet, mm
Outlet, mm
Oil capacity, L
Weight, kg
Cat. No.
2.3 (38)
2.7 (45)
1.3x101
6
11 or 15 nozzle
12
0.5
12.5
Description
Price
691-020
POA
POA
Protection from oil mist emissions as required by COSHH and Health and Safety regulations
(EMF filters have 99.999% efficiency)
The white bottom half of the body is translucent, allowing the oil level to be monitored
For safety, if the oil element becomes blocked, an integral pressure relief valve will open
Cat. No.
Description
Price
691-020 EMF10, oil mist filter complete with KF25 connections 34in. BSP to KF25 adaptor,
centring ring with O ring and clamp. Fits RV3, 5 and 8
691-019 EMF3, oil mist filter supplied complete as above but fits Speedivac 2
POA
POA
757
Pumps
Edwards
520-036
520-040
Typical applications for XDS-C pumps: gel drying, rotary evaporation, centrifugal concentration and
other applications where condensable vapour are pumped.
Typical applications for XDS pumps: scanning electron microscopes, ion implanters (beamline and end
stations), sputtering, turbomolecular pump backing and general clean pumping applications.
3-position gas ballast selector - Pumps in excess of 200 gh1 water vapour
Ease of maintenance - No oil to buy, change or dispose of, no re-greasing of bearings, no special
tool kits or jigs for service, simple supply voltage selection
Dual voltage/frequency
Specifications
Model
Displacement
50Hz, m3/h (L/min)
60Hz, m3/h (L/min)
Peak pumping speed
50Hz, m3/h (L/min)
60Hz, m3/h (L/min)
Ultimate vacuum
(total pressure), mbar
Water vapour handling, gh-1
gas ballast low/ high flow
Motor supply voltage
50Hz/ 60Hz 1 phase
50Hz/ 60Hz 3 phase
Power, kW
Operating temperature, C (F)
Noise level, dB(A)
Vibration, mms-1 (rms)
Water vapour handling, gh-1
gas ballast low/ high flow
Exhaust and inlet connection
Dimensions (lxwxh), mm
Weight, kg
XDS5
XDS10
XDS5-C
XDS10-C
5.7 (94)
6.7 (111)
11.3 (186)
13.4 (221)
5.7 (94)
6.7 (111)
11.3 (186)
13.4 (221)
4.8 (94)
6.0 (99)
0.07
9.3 (153)
11.1 (183)
0.07
4.8 (79)
6.0 (99)
0.9
9.3 (153)
11.1 (183)
0.9
70/>200
70/>200
70/>200
70/>200
70/>200
25NW
23
70/>200
70/>200
25NW
25NW
427x249x288 (all models)
24.5
23
520-034
520-036
520-038
520-040
Price
POA
POA
POA
POA
520-035
520-037
520-039
520-041
Price
POA
POA
POA
POA
24.5
Accessories
Cat. No.
Description
520-028
520-025
520-042
520-043
Price
POA
POA
POA
POA
A new model, the XDS35i is also available, this has a peak pumping speed of 35m3/h. Please contact our Technical
Office on 01342 826836 for details.
758
Pumps
KNF
521-057
Easy operation
Maintenance-free
Specifications
521-201
Model
Flow rate, m3/h (L/min)
Vacuum, mbar
Pressure, bar
Diaphragm
Dimensions (wxdxh), mm
Weight, kg
N86 KN.18
0.36 (6)
100
2.4
EPDM
90x164x141
1.9
N86 KT.18
0.33 (5.5)
160
2.5
PTFE coated
90x164x141
1.9
N811 KN.18
0.69 (11.5)
240
2
EPDM
90x187x157
2.5
N811 KT.18
0.69 (11.5)
290
2
PTFE coated
90x187x157
2.5
Cat. No.
521-057
521-200
521-201
521-202
Price
POA
POA
POA
POA
N816.3 KN.18
0.96 (16)
15
0.5
EPDM
90x361x141
3.95
N816.3 KT.18
0.96 (16)
20
0.5
PTFE coated
90x361x141
3.95
N816.1.2 KN.18
1.8 (30)
100
0.5
EPDM
90x361x141
3.95
N816.1.2 KT.18
1.8 (30)
160
0.5
PTFE coated
90x361x141
3.95
Cat. No.
521-203
521-204
521-205
521-206
Price
POA
POA
POA
POA
Specifications
521-204
Model
Flow rate, m3/h (L/min)
Vacuum, mbar
Pressure, bar
Diaphragm
Dimensions (wxdxh), mm
Weight, kg
The Laboport series provides a powerful alternative to water jet pumps, operating without water. They
therefore save water and reduce environmental pollution. They also reduce operating costs dramatically.
The pumps provide a constant vacuum, independent of water pressure and temperature. With the
exception of N840.1.2FT.18 and N842.3FT.18, these pumps are single-head designs.
Specifications
521-029 to 521-031
Model
Flow rate, m3/h (L/min)
Vacuum, mbar abs
Pressure, bar
Dimensions (wxdxh), mm
Weight, kg
N810 FT.18
0.6 (10)
100
1.0
256x146x187
5.9
N820 FT.18
1.2 (20)
100
1.0
268x159x207
7.1
N840 FT.18
2 (34)
100
1.0
297x171x226
10.3
N810.3 FT.18
0.6 (10)
8
1.0
281x140x187
6.9
Cat. No.
521-053
521-054
521-055
521-029
Price
POA
POA
POA
POA
N820.3 FT.18
1.2 (20)
8
1.0
312x154x207
9.3
N840.3 FT.18
2 (34)
8
1.0
341x166x226
12.6
N842.3 FT.18
2 (34)
2
1.0
341x167x223
13.4
N840.1.2 FT.18
3.6 (60)
90
1.0
341x160x226
12.6
Cat. No.
521-030
521-031
521-093
521-091
Price
POA
POA
POA
POA
Specifications
521-093
760
Model
Flow rate, m3/h (L/min)
Vacuum, mbar abs
Pressure, bar
Dimensions (wxdxh), mm
Weight, kg
Pumps
KNF
521-094
521-092
521-090
521-021
KNF Laboport pumps feature chemically resistant materials (e.g. PTFE, FFPM) in contact with the gas
stream. There are no metal parts to corrode. KNFs moulded structural diaphragm and multiport design
ensure reliable vacuum performance.
521-022
Specifications
Model
Flow rate, m3/h (L/min)*
Vacuum, mBar abs
Pressure, bar
Dimensions (wxdxh), mm
Weight, kg
N820.3 FT.40.18
1.2 (20)
10
1.0
312x177x220
9.6
N840.3 FT.40.18
2 (34)
10
1.0
341x189x239
12.9
N842.3 FT.40.18
2 (34)
4
1.0
341x189x242
13.7
N860.3 FT.40.18
3.6 (60)
4
1.0
331x291x278.5
14.8
Cat. No.
521-090
521-092
521-094
521-095
Price
POA
POA
POA
POA
521-024
Specifications
Model
Flow rate, m3/h (L/min)
Vacuum, mBar
Compression, bar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
N 022 AN.18
0.9 (15)
100
4
203x103x194
4
240V/50Hz/60W
N 035 AN.18
1.8 (30)
100
4
265x143x254
8.2
240V/50Hz/220W
N 035.3 AN.18
1.8 (30)
13
294x250x222
11.3
240V/50Hz/300W
Cat. No.
521-021
521-022
521-024
Price
POA
POA
POA
Accessories
Cat. No.
N 022 AN.18
N 035 AN.18
Price
POA
POA
Cat. No.
Description
For model
N 035.3 AN.18
Price
POA
761
Pumps
Vacuubrand
Diaphragm Pumps
521-104
Vacuubrand diaphragm pumps are totally oil free, mechanical vacuum pumps.
Two basic versions are available:
Standard version
The materials of the wetted parts are made of aluminium, FPM (e.g. Viton) and polyamide. This is
adequate for less aggressive gases and vapours.
Chemistry version
All wetted parts of the chemistry version are made of chemically resistant fluorinated plastic materials, e.g.
PTFE-sandwich diaphragms or ECTFE (e.g., Halar) clamping discs with stainless steel core. This makes the
Chemistry version ideal for rotary evaporation, distillation, vacuum concentration, gel drying etc.
Vacuubrand diaphragm pumps offer high flow rates at low vacuum, excellent reliability and vacuum
stability. They are inexpensive and simple to service and maintain. All units are supplied with on/off
switch, mains cable with plug and instructions. The Chemistry versions are also supplied with gas ballast.
521-101
High performance
Low noise
Compact
Pollution free
Long lifetime
ME2
1.9 (31)
<80
2
275x173x175
6.3
230V, 50/60Hz
ME4
3.7 (61)
<80
4
266x235x175
10.1
230V, 50/60Hz
ME4R
3.6 (56)
<100
4
226x235x175
11.0
230V, 50/60Hz
ME8
6.5 (108)
<80
2
315x235x200
15.5
230V, 50/60Hz
Cat. No.
521-104
521-105
521-101
521-106
Price
POA
POA
POA
POA
ME2C
1.7 (28)
80
2
258x173x178
6.6
230V, 50/60Hz
MZ2C
1.7 (28)
9
2
266x241x170
10.5
230V, 50/60Hz
MD1C
1.0 (16)
2
1.1
303x165x215
6.5
230V, 50/60Hz
MD4C
3.0 (50)
2
1.1
315x241x176
16.2
230V, 50/60Hz
Cat. No.
521-088
521-107
521-108
521-176
Price
POA
POA
POA
POA
521-176
521-110
The oil free chemistry diaphragm pumping units with condensate catchpots can be used in a wide range
of applications for evaporation or pumping of corrosive gases. The special catchpot system improves
lifetime and reliability and the exhaust waste vapour condenser (on +EK models only) offers highly
efficient solvent recovery.
All units are supplied with pump stand and inlet catchpot, on/off switch, mains cable with plug and
instructions. In addition, unit MZ2C+2AK is supplied with an exhaust catchpot, whereas units
MZ2C+AK+EK, MD1C+AK+EK and MD4C+AK+EK are supplied with an exhaust condenser.
762
MZ2C+2AK
1.7 (28)
9
336x241x326
13.5
230V, 50/60Hz
MZ2C+AK+EK
1.7 (28)
9
336x241x500
13.5
230V, 50/60Hz
MD1C+AK+EK
1.0 (16)
2
336x165x500
9.2
230V, 50/60Hz
MD4C+AK+EK
3.0 (50)
2
315x241x176
16.2
230V, 50/60Hz
Cat. No.
521-109
521-110
521-111
521-112
Price
POA
POA
POA
POA
Pumps
Vacuubrand
521-113
The Vacuubrand laboratory pumping units generate totally oil free vacuum, maintain predetermined
vacuum, control exhaust vapour emissions and allow solvent recovery. The pumping unit components are
made of chemically resistant materials. Units PC510 and PC610 have one vacuum controller, units PC520
and PC620 are supplied with two vacuum controllers.
All units are supplied with chemistry diaphragm pump on pump support, catchpot (inlet side) with
isolation valve, vacuum controller, air admittance valve, exhaust waste vapour condenser and instructions.
PC510
1.7 (28)
9
400x251x536
18.5
230V, 50/60Hz
PC520
1.7 (28)
9
400x369x538
21
230V, 50/60Hz
PC610
3.0 (50)
2
400x251x536
25.0
230V, 50/60Hz
PC620
6.5 (108)
2
400x369x538
27.5
230V, 50/60Hz
Cat. No.
521-113
521-114
521-115
521-116
Price
POA
POA
POA
POA
521-117
All units are supplied with chemistry diaphragm pump mounted on pump support, vacuum controller
CVC2000, catchpot inlet side, exhaust waste vapour condenser and instructions.
PC2001
1.5 (25)
2
310x280x470
9.2
230V, 50/60Hz
PC2003
1.9 (31)
0.6
400x251x536
25.0
230V, 50/60Hz
PC2004
3.8 (63)
2
400x251x536
25.0
230V, 50/60Hz
PC2010
8.2 (136)
0.6
650x370x610
37.0
230V, 50/60Hz
Cat. No.
521-117
521-118
521-119
521-120
Price
POA
POA
POA
POA
521-121
All units are supplied with on/off switch, mains cable with plug and instructions.
Description
RC5
5.6 (93)
4x10-4
2x10-3
505x300x210
25.5
230V, 50/60Hz
Price
POA
763
Pumps
Vacuubrand
New
521-126
New
521-127
High vapour tolerance - for water and solvents with gas ballast of about 10%
Anti-corrosion design - plasma treated internal surfaces and oil shut-off device to prevent back
flow of gases
Quieter operation with longer service intervals - improved lubrication circuit and larger oil reservoir
Reduced power consumption - improved motor design with immediate re-start after shutdown
Specifications
Model
Maximum flow rate, m3/hr (L/min)
Ultimate vacuum without gas ballast, mbar
Ultimate vacuum with gas ballast, mbar
Water vapour tolerance, mbar
Water vapour capacity, gh-1
Dimensions (lxwxh), mm
Weight, kg
Electrical supply
New
521-128
RE2.5
RZ2.5
RE6
2.3/2.8 (47) 2.3/2.8 (47) 5.7/6.8 (113)
3x10-1
2x10-3
1x10-1
8x10-1
1x10-2
6x10-1
40
40
40
65
65
159
308x125x190 308x125x190 370x142x207
10.2
11.4
15.3
230V, 50/60Hz (all models)
RZ6
5.6 (113)
2x10-3
1x10-2
40
159
370x142x207
16.4
Cat. No.
521-122
521-126
521-123
521-127
Price
POA
POA
POA
POA
Specifications
Model
Maximum flow rate, m3/hr (L/min)
RE16
16.6/19.1
(318)
1x10-1
2x10-3
1x10-1
6x10-1
1x10-2
6x10-1
40
40
40
246
246
474
460x152x232 460x152x232 505x152x232
22.1
24.6
25.2
230V, 50/60Hz (all models)
RZ16
16.6/19.1
(318)
2x10-3
1x10-2
40
474
545x152x232
29
Cat. No.
521-124
521-128
521-125
521-129
Price
POA
POA
POA
POA
RE9
RZ9
8.6/9.9 (165) 8.6 (165)
764
Pumps
Vacuubrand
Pump Accessories
521-132
521-178
Oil mist filter - prevents loss of oil to atmosphere and reduces condensate build up in pumps.
Cat. No.
Description
For Model
Price
521-130
521-131
521-132
521-177
521-178
Inlet separator
Inlet separator
Inlet separator
Oil mist filter
Oil mist filter
RE2.5/RZ2.5
RE6/RZ6
RE9/RZ9, RE16/RZ16
RE2.5/RZ2.5, RE6/RZ6
RE9/RZ9 RE16/RZ16
POA
POA
POA
POA
POA
Cold Traps
GKF 1000i - glass cold trap with mirror insulated jacket, PTFE stopcock, sight strip and implosion protection.
SKF H - stainless steel cold trap offers excellent cooling properties, is easy to drain, disassemble and clean.
521-177
Cat. No.
Description
Connections
For Model
Price
POA
POA
POA
CVC211*
Rough vacuum
controller
1300 to 1
<0.5% of range
DVR2
Rough vacuum
gauge
1080 to 1
<1
DVR5
Rough vacuum
gauge
1100 to 0.1
1
Capacitive,
independent
of gas type
Capacitive,
independent
of gas type
VAP5
Fine vacuum
gauge
1000 to 10-3
10% of
indicated value
Pirani
(thermal
conductivity)
Cat. No.
521-136
521-137
521-138
521-139
Price
POA
POA
POA
POA
Piezoresistive
521-133
* Operates in conjunction with Vacuubrand 24v magnetic solenoid valves, see cat item 521-175.
Service Kits
Cat. No.
Description
For Model
521-140
521-141
521-142
521-143
521-144
521-145
521-146
521-147
521-148
521-149
Service kit
Service kit
Service kit
Service kit
Service kit
Service kit
Service kit
Service kit
Service kit
Service kit
ME2
ME4, ME4R
ME8
ME2C
MZ2C
MD1C
RE2.5/RZ2.5, RE6/RZ6
RE9/RZ9, RE16/RZ16
RC5
MD4C
Price
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
521-137
765
Pumps
Ilmvac
New
521-150
Compact design
Supplied with oil, mains lead and plug and gas ballast valve. Other models with various flow rates and
ultimate vacuums available.
Specifications
New
521-152
Model
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Water vapour tolerance, mbar
Dimensions (wxdxh), mm
Weight, kg
Oil capacity, ml
Electrical supply
PK2DC
1.8 (30)
<1x10-3
33
300x120x150
8
250
PK4Dp
PK6Dp
4.6 (76)
6.4 (106)
<2x10-4
<2x10-4
40
40
405x150x200
405x150x200
19
19
500
500
230V, 50/60Hz (all models)
PK8Dp
8.3 (138)
<2x10-4
40
430x150x200
21.5
650
Cat. No.
521-150
521-152
521-300
521-154
Price
POA
POA
POA
POA
Accessories
Cat. No.
Description
Price
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
Other models with various flow rates and ultimate vacuums are available. Please contact our Technical Office on
01342 826836 for details.
New
521-310
Fully chemically resistant scroll vacuum pump with high vapour tolerance for laboratory applications
requiring fine vacuum. Uniquely, only the scroll is under vacuum. PTFE surfaces and seals achieve class
leading resistance to chemical processes. The vertical shaft design places the exhaust port at the lowest
point in the pump allowing condensed solvents to run out of the pump.
PTFE seals
Specification
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Water vapour tolerance, mbar
Motor power, kW
Dimensions (lxwxh), mm
Connection
Weight, kg
Electrical supply
Cat. No.
10 (67)
7x10-2
50
0.55
470x320x440
DN25KF
30
230V, 50/60Hz
Description
766
Price
POA
Pumps
Ilmvac
512-312
General purpose laboratory vacuum pump designed for high vapour tolerance and incorporating intake
separator and exhaust side oil mist eliminator. The pump is pre-filled with oil (oil capacity: 500ml) and
hosetail connections are also included to enable the pump to be used straight out of the box.
Compact design
Supplied with oil, mains lead and plug, inlet and outlet 12mm nozzles, exhaust mist filters and inlet
catch-pot.
Specification
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Water vapour tolerance, mbar
Motor power, kW
Separator on intake side
Oil mist eliminator, exhaust side
Connections intake and outlet
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
Cat. No.
4.6 (76)
2x10-4
40
0.37
Glass catch-pot, nickelised aluminium connection, mounted to side of
pump body
Glass catch-pot with coalescing filter media and over-pressure protection, nickelised aluminium connection, mounted to side of pump body
DN16KF flange supplied with 12mm hose nozzle, clamp and seal
405x150x200
19
230V, 50/60Hz
Description
Price
POA
Accessories
Cat. No.
Description
Price
POA
521-166
New
The HBP100 is a new and unique solution for solvent evaporation and condensation. It provides a
complete, automatically controlled vacuum pump and condenser unit at considerable capital cost savings
over conventional solutions.
No solvent bumping
Environmentally sound
Small Footprint
Specification
Pumping speed, L/min (m3/hr)
Ultimate vacuum, mbar
Vacuum connection
Exhaust connection
Water connections
Solvent collection vessel round flask
Noise level
Electrical supply
Protection
Dimensions (wxdxh), mm
Weight, kg
Cat. No.
Description
2.3 (40)
10, self-regulating
hose nozzle DN10 for 10mm ID tubing
clamping union for 6mm ID tubing
clamping union for 6mm ID tubing
1000ml with S35 joint and clamp
<45 db(A)
230V/50Hz
IP42
375x460x395
8.9
Price
POA
767
Pumps
Ilmvac
521-157
A highly cost efficient range of PTFE diaphragm pumps. The diaphragm and all parts coming into contact
with the vapours are PTFE or PTFE-compounds. Supplied ready for use with a 2 year warranty.
Supplied with carry handle, mains lead and plug, gas ballast valve, exhaust silencer and 8mm inlet and
outlet nozzles.
Specifications
New
521-530
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
MPC102E
0.8 (13)
<75
124x210x223
5.7
MPC201E
MPC601E
MPC1201E
1.8 (30)
3.8 (63)
8.3 (138)
<75
<75
<75
195x235x145 230x265x169 230x265x169
6.5
7.8
12.5
230V, 50/60Hz (all models)
MPC2401E
15.5 (258)
<75
540x300x240
24.0
Cat. No.
521-157
521-526
521-527
521-528
521-529
Price
POA
POA
POA
POA
POA
MPC052Z
0.5 (8)
<8
124x210x223
5.7
MPC101Z
MPC301Z
MPC901Z
1.0 (17)
2.3 (38)
6.8 (113)
<8
<8
<8
195x235x145 230x265x169 230x265x169
6.5
7.8
12.5
230V, 50/60Hz (all models)
MPC1801Z
12.0 (200)
<8
540x300x240
24.0
Cat. No.
521-158
521-159
521-160
521-530
521-531
Price
POA
POA
POA
POA
POA
MPC201T
2.0 (33)
<2
200x260x150
10.3
MPC601T
MPC1201T
4.5 (75)
8.3 (138)
<2
<2
230x380x169 540x300x240
12.5
24
230V, 50/60Hz (all models)
MPC301V
2.3 (38)
<1
230x380x169
12.5
Cat. No.
521-161
521-532
521-533
521-534
Price
POA
POA
POA
POA
Specifications
New
521-533
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
Specifications
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
521-159
Service kits are available. Please contact our Technical Office on 01342 826836 for details.
Other models with various flow rates and ultimate vacuums available. Please contact our Technical Office on 01342
826836 for details.
768
Pumps
Ilmvac
521-511
New
521-515
New
521-519
New
521-520
New
A low cost range of diaphragm pumps for general applications not requiring chemical resistance.
Supplied ready for use with a 2 year warranty.
Aluminium construction
Applications include: Aqueous filtration, vacuum tweezers, vacuum ovens, general applications
to 1 mbar
Pumps are supplied ready to use with carrying handle, mains lead and plug, 8mm inlet connection and
exhaust silencer.
Specifications
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
MP102E
0.8 (13)
<75
124x210x223
5.7
MP201E
MP601E
MP1201E
1.8 (30)
3.8 (63)
8.3 (138)
<75
<75
<75
195x235x145 230x265x169 230x265x169
6.5
7.8
12.5
230V, 50/60Hz (all models)
MP2401E
15.53 (258)
<75
540x300x240
24.0
Cat. No.
521-510
521-511
521-512
521-513
521-514
Price
POA
POA
POA
POA
POA
MP052Z
0.5 (8)
<8
124x210x223
5.7
MP101Z
MP301Z
MP901Z
1.0 (17)
2.3 (38)
6.8 (113)
<8
<8
<8
195x235x145 230x265x169 230x265x169
6.5
7.8
12.5
230V, 50/60Hz (all models)
MP1801Z
12.0 (200)
<8
540x300x240
24.0
Cat. No.
521-515
521-516
521-517
521-518
521-519
Price
POA
POA
POA
POA
POA
MP201T
2.0 (33)
<2
200x260x150
10.3
MP601T
MP1201T
MP101V
4.5 (75)
8.3 (138)
1.0 (17)
<2
<2
<1
230x380x169 540x300x240 200x260x150
12.5
24
10.3
230V, 50/60Hz (all models)
MP301V
2.3 (38)
<1
230x380x169
12.5
Cat. No.
521-520
521-521
521-522
521-523
521-524
Price
POA
POA
POA
POA
POA
Specifications
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
Specifications
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
Specification
Model
Flow rate, m3/hr (L/min )
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
MP030Z
0.4 (5)
<5
102x116x45
0.8
230V, 50/60Hz
Cat. No.
521-525
Price
POA
For details on accessories, including service kits please contact our Technical Office on 01342 826836.
769
Pumps
Ilmvac
New
521-573
2 year warranty
This unique product is supplied fully configured and ready to use. Tubing connection for vacuum and
process are 8mm hose barbs.
New
521-563
Specification
Measuring range, mbar
Accuracy, mbar
Display
Dimensions (wxdxh), mm
Thresholds/output at front panel
Vacuum connection at sensor
Weight, kg
Electrical supply
Cat. No.
1100 to 1
2
LED in mbars and tors
200x170x165
24V DC 10W per channel, 30W total
female thread 1/4 inch, DN 16 KF
1.5
90-240V, 50-60Hz, 40W
Description
Price
POA
New
521-564
2 year warranty
Pumps are supplied ready to use, charged with oil, with mains lead and plug, inter-stage catch-pots and
KF16 or KF25 connections.
Specifications for pumps with one rotary vane stage and two PTFE diaphragm stages
New
521-567
Model
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
4S-101
3.7 (62)
<3x10-2
470x230x320
18.2
8S-101
12S-101
17S-101
7.3 (120)
11.0 (183)
16.0 (266)
<3x10-2
<3x10-2
<3x10-2
470x230x320 480x230x380 570x230x380
19.0
25.0
30.0
230V, 50/60Hz (all models)
23S-101
21.0 (350)
<3x10-2
570x230x380
35.0
Cat. No.
521-563
521-564
521-565
521-566
521-567
Price
POA
POA
POA
POA
POA
Specifications for pumps with two rotary vane stages and two PTFE diaphragm stages
Model
Flow rate, m3/hr (L/min)
Ultimate vacuum, mbar
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
4D-101
3.7 (62)
<3x10-3
470x230x320
19.0
8D-101
12D-101
17D-101
7.3 (120)
11.0 (183)
16.0 (266)
<3x10-3
<3x10-3
<3x10-3
470x230x320 480x230x380 570x230x380
21.3
26.0
31.0
230V, 50/60Hz (all models)
23D-101
21.0 (350)
<3x10-3
570x230x380
36.0
Cat. No.
521-568
521-569
521-570
521-571
521-572
Price
POA
POA
POA
POA
POA
For details on accessories, including service kits please contact our Technical Office on 01342 826836.
770
Pumps
Ilmvac
521-538
New
521-553
New
521-556
New
The latest solutions for solvent handling in the laboratory, LVS units are based on the MPC range of
chemically resistant diaphragm pumps with solvent containment condensers. They are available with or
without control. There are four control options available:
None: The vacuum level is not controlled.
Standard Valve: The vacuum pump operates continuously and the process vacuum level is controlled
by a chemically resistant solenoid valve. Set points can be preset, altered during the process, or
determined automatically using the boiling point finding facility.
Management: The pump starts and stops automatically to maintain vacuum within your set range.
Ideal for operating vacuum lines and networks where service intervals are greatly extended.
Ecoflex: The pumps flow rate is automatically varied to maintain the set point by matching the vapour
load. Set points can be preset, altered during the process, or determined automatically using the boiling
point finding facility. Ideal for rotary evaporators, where process times can be reduced by up to 30%.
Service intervals are greatly extended. VCZ324 controller included.
Only PTFE compounds and glass in contact with the vapour stream
Small footprint
Systems are supplied ready to use with pump, inlet catch-pot, water cooled emission condenser, mains
lead and plug. Optional control modes fully installed where selected.
Specifications - Two stage vacuum systems with no control or standard valve control
Models
LVS 0501
LVS 0501RM
LVS 0510
0.4 (8)
<8
310x270x520
9.1/9.2/9.6
230V, 50/60Hz
LVS 101
LVS 101RM
LVS 110
1.0 (17)
<8
310x270x520
10.5/11.0/13.2
230V, 50/60Hz
LVS 300
LVS 301
LVS 302
2.3 (38)
<8
310x270x520
17.5/18.5/17.5
230V, 50/60Hz
LVS 310
LVS 311
LVS 320
2.3 (38)
<8
310x270x520
19.2/19.5/19.8
230V, 50/60Hz
Specifications - Three stage vacuum systems with no control or standard valve control
Models
LVS 201T
LVS 210T
1.8 (33)
<2
310x270x520
14.0/15.0
230V, 50/60Hz
LVS 601T
LVS 602T
4.5 (75)
<2
310x270x520
25.0/22.5
230V, 50/60Hz
LVS 610T
LVS 611T
LVS 620T
4.5 (75)
<2
310x270x520
26.5/27.0/27.5
230V, 50/60Hz
LVS1201T
8.3 (138)
<2
540x310x520
30.0
230V, 50/60Hz
LVS 110 M
1.0 (17)
<8
310x270x520
19.2
230V, 50/60Hz
LVS 310 M
LVS 310 E
2.3 (38)
<8
310x270x520
20.5/14.7
230V, 50/60Hz
LVS 210T E
1.8 (33)
<2
310x270x520
20.7
230V, 50/60Hz
LVS 610 TM
LVS 610 TE
4.5 (75)
<2
310x270x520
27.5/28.5
230V, 50/60Hz
LVS 1210 TM
LVS 1210 TE
8.3 (138)
<2
540x310x520
30.5/32.0
230V, 50/60Hz
521-562
New
Laboratory vacuum systems are supplied ready to use with pump, inlet catch-pot, water cooled emission condenser,
mains lead and plug.
771
Pumps
Ilmvac
Description
Price
521-535 LVS 0501 Laboratory vacuum system with MPC 052Z pump, one uncontrolled connection
521-536 LVS 0501 RM Laboratory vacuum system with MPC 052Z pump, manometer, one uncontrolled connection
521-537 LVS 0510 Laboratory vacuum system with MPC 052Z pump, controller
complete module with external sensor, airing valve, one controlled connection
521-538 LVS 101 Laboratory vacuum system with MPC 101Z pump, one uncontrolled connection
521-539 LVS 101 RM Laboratory vacuum system with MPC 101Z pump, manometer, one uncontrolled connection
521-540 LVS 110 Laboratory vacuum system with MPC 101Z pump, controller
complete module with external sensor, airing valve, one controlled connection
521-541 LVS 300 Laboratory vacuum system with MPC 301Z pump
521-542 LVS 301 Laboratory vacuum system with MPC 301Z pump, one uncontrolled connection
521-543 LVS 302 Laboratory vacuum system with MPC 301Z pump, two uncontrolled connections
521-544 LVS 310 Laboratory vacuum system with MPC 301Z pump, controller
complete module with external sensor, airing valve, one controlled connection
521-545 LVS 311 Laboratory vacuum system with MPC 301Z pump, controller
complete module with external sensor, airing valve, one controlled and one uncontrolled connection
521-546 LVS 320 Laboratory vacuum system with MPC 301Z pump, controller
complete module with external sensor, airing valve, two controlled connections
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
Description
Price
521-547 LVS 201T Laboratory vacuum system with MPC 201T pump, one uncontrolled connection
521-548 LVS 210T Laboratory vacuum system with MPC 201T pump, controller
complete module with external sensor, airing valve, one controlled connection
521-549 LVS 601T Laboratory vacuum system with MPC 601T pump, one uncontrolled connection
521-550 LVS 602T Laboratory vacuum system with MPC 602T pump, two uncontrolled connections
521-551 LVS 610T Laboratory vacuum system with MPC 601T pump, controller
complete module with external sensor, airing valve, one controlled connection
521-552 LVS 611T Laboratory vacuum system with MPC 601T pump, controller
complete module with external sensor, airing valve, one controlled and one uncontrolled connection
521-553 LVS 620T Laboratory vacuum system with MPC 601T pump, controller
complete module with external sensor, airing valve, two controlled connections
521-554 LVS 1201T Laboratory vacuum system with MPC 1201T pump, controller
complete module with external sensor, airing valve, one controlled connection
POA
POA
POA
POA
POA
POA
POA
POA
Description
Price
521-555 LVS 110M Laboratory vacuum system with MPC 101Z pump and management system
521-556 LVS 310M Laboratory vacuum system with MPC 301Z pump and management system
521-559 LVS 310E Ecoflex laboratory vacuum system with MPC 301Z pump and VCZ324 controller
POA
POA
POA
Description
521-560
521-557
521-561
521-558
521-562
LVS 210TE Ecoflex laboratory vacuum system with MPC 201T pump and VCZ324 controller
LVS 610TM Laboratory vacuum system with MPC 601T pump and management system
LVS 610TE Ecoflex laboratory vacuum system with MPC 601T pump and VCZ324 controller
LVS 1210TM Laboratory vacuum system with MPC 1201T pump and management system
LVS 1210TE Ecoflex laboratory vacuum system with MPC 1201T pump and VCZ324 controller
Price
For details on accessories, including service kits please contact our Technical Office on 01342 826836.
772
POA
POA
POA
POA
POA
Pumps
Ilmvac, PLS301Z Diaphragm Pump System
New
521-313
Oil-free, mechanical vacuum pump, mounted on pump holder, with intake-side separator, delivery-side
emission condenser cooled by dry ice slurry.
Suitable for all applications between atmosphere and 8 mbar absolute including rotary and centrifugal
evaporation, gel drying, filtration, drying ovens, desiccators and more.
Specification
Flow rate, m3/hr (L/min)
at 1000 mbar/20 mbar
Ultimate pressure, mbar
Without gas ballast
Construction
Connections
Dimensions (wxdxh), mm
Weight, kg
Electrical supply
CE conformity
Cat. No.
Description
Price
POA
451-150
These innovative double stage rotary vane pumps are suitable for all applications in the rough and
medium vacuum range, featuring pumping speeds of 80 to 160L/min. The drive concept integrated
magnetic coupling ensures that the pumps are hermetically sealed. Separating the rotor and motor
shafts solves the problem connected with rotary shaft seals. The wear-free drive prevents leaks, keeps
maintenance to a minimum and considerably lengthens the pumps working life.
Pfeiffer rotary vane pumps also offer more process safety, with the high speed high vacuum safety valve
integrated as standard. This fast, hydraulically-controlled valve stops the pump immediately in the event
of faults such as power failure, undervoltage or process safety cutoff. Supplied with operating lubricant.
Specifications
Model
Nominal pumping speeds, m3/h (L/min)
Ultimate vacuum, mbar
without gas ballast/with gas ballast
Exhaust pressure maximum, mbar
Lubricant amount, L
Weight (approximate), kg
Dimensions (wxdxh), mm
DUO 005M
4.8 (80)
3
<5x10 /<2x10
1500
0.75
22
176x435x217
rotor shaft
DUO 010M
9.7 (160)
2
<5x10 /<1x10
1500
1.0
28
178x517x216
motor shaft
"environment"
" vacuum"
sleeve
O-ring
Inner magnet
" vacuum"
Cat. No.
451-149
451-150
rotor shaft
Price
POA
POA
" vacuum"
Accessories
Outer magnet
Cat. No.
Description
Price
POA
POA
Cat. No.
Description
Price
POA
POA
773
Pumps
Heidolph
New
Various chemically resistant and sterilisable tubes available for individual applications
3 year warranty
New
These peristaltic pump drives are suitable for standard applications; they have electronic speed control
(accuracy 2%), large dials for speed setting, protection to IP30 and can be stacked (up to 3 pump
drives). Flow can be clockwise or counter clockwise.
The PD 5001 provides flow rates from 0.7 to 729ml per minute with a speed range of 10 to 120rpm. It
can also be equipped with two pumps heads (SP quick and SP quick d) or with a multi-channel pump
head (C4, C8 or C12 - an adaptor is required but not supplied). Multi-channel flow rates are from 0.01
to 336ml/min.
Model PD 5006 provides flow rates from 3.3 to 3,644ml per minute with a speed range of 50 to 600rpm.
It is suitable for any of the single pumps heads, however it is not suitable for the use of multi-channel
pump heads.
New
The PD 5101 provides flow rates from 0.3 to 729ml per minute with a speed range of 5 to 120rpm. It can
also be equipped with two pumps heads (SP quick and SP quick d) or with a multi-channel pump head
(C4, C8 or C12 - an adaptor is required but not supplied). Multi-channel flow rates are from 0.005 to
336ml/min.
Model PD 5106 provides flow rates from 1.6 to 3,644ml per minute with a speed range of 24 to 600rpm.
It is suitable for any of the single pumps heads, however it is not suitable for the use of multi-channel
pump heads.
New
Flow rates of the pump heads in combination with the various tubing are saved in the program
to enable direct digital readout of flow rate
Pump drive PD 5201 provides flow rates from 0.3 to 729ml per minute with a speed range of 5 to
120rpm. It can also be equipped with two pumps heads (SP quick and SP quick d) or with a multi-channel
pump head (C4, C8 or C12 - an adaptor is required but not supplied). Multi-channel flow rates are from
0.005 to 336ml/min.
Model PD 5106 provides flow rates from 1.6 to 3644ml per minute with a speed range of 24 to 600rpm.
It is suitable for any of the single pumps heads, however it is not suitable for use with multi-channel
pump heads.
774
Pumps
Heidolph
New
New
New
New
Specifications
Model
Flow rate ranges, ml/min
Flow rate - multi-channel
pump, ml/min
Speed range, rpm
Dimensions (wxhxd), mm
Weight, kg
PD 5001
0.7729
0.01336
PD 5006
3.33644
N/A
PD 5101
PD 5106
0.3729
1.63644
0.005336 N/A
PD 5201
PD 5206
0.3729
1.6-3644
0.005336 N/A
10120
166x225
x256
6.8
50600
166x225
x256
6.2
5120
166x225
x256
8.2
5120
166x225
x256
8.3
Cat. No.
Description
521-600
521-601
521-602
521-603
521-604
521-605
24600
166x225
x256
7.6
24600
166x225
x256
7.7
Price
POA
POA
POA
POA
POA
POA
Pump drives are supplied without a pump head or tubing. Please see below for details.
Specifications
Model
Flow rate ranges, ml/min
Tubing wall thickness, mm
Number of rollers
SP quick 1.6
0.32217
1.6
5
Cat. No.
Description
521-630
521-631
521-632
521-633
SP quick 2.5
11.23300
2.5
5
SP quick d 1.6
0.32217
1.6
5
SP quick d 2.5
11.23300
2.5
5
521-631
521-633
Price
POA
POA
POA
POA
To attach two pump heads to one drive unit, choose SP quick in combination with SP quick d.
New
775
Pumps
Heidolph
New
521-634
New
521-636
New
521-643
SP standard 1.6
0.53644
1.6
2
SP standard 2.5
17.33644
2.5
2
SP vario
0.53644
Various*
2
Cat. No.
521-634
521-635
521-636
Price
POA
POA
POA
* Suitable for most Heidolph tubing due to adjustable roller spacing. For more information please contact our
Technical Office on 01342 826836.
New
521-637
New
521-638
The C4 pump head has 8 rollers for low-pulsation and accepts 4 small cassettes. Cassettes may be
partially used and click easily into place.
New
New
521-639
521-640
New
521-641
Cat. No.
Description
521-637
521-638
521-639
521-643
521-640
521-641
521-642
Price
POA
POA
POA
POA
POA
POA
POA
* A multi-channel adaptor is required to connect the pump drives PD 5001, PD 5101 and PD 5201 to a multi-channel
pump head (pump drives PD 5006, PD 5106 and PD 5206 are not suitable for use with multi-channel pump heads). Also,
if you already have a Heidolph single drive pump an adaptor is required to connect this to a multi-channel pump head.
New
521-642
Tubing bore, mm
SP quick
PD 5106/5206
PD 5006
PD 5101/5201
PD 5001
SP standard/SP Vario
PD 5106/5206
PD 5006
PD 5101/5201
PD 5001
0.8
3.1
6.3
1.640
3.340
0.38.0
0.78.0
25.7643
53.6643
5.2129
10.7129
88.72217
184.82217
17.7443
37.0443
2.460.2
5.060.2
0.512.0
1.012.0
41.21029
85.81029
8.2206
17.2206
1463644
3043644
29.2729
60.7729
521-606
521-607
521-608
Price
POA
POA
POA
521-609
521-610
521-611
Price
POA
POA
POA
Other tubing sizes are available including, 1.7mm and 4.8mm. The following tube sizes are also available with a wall
thickness of 2.5mm: 4.8, 6.3 and 7.9mm. For details on these and other tubing materials (Viton, PharMed, Tygon
(hydrocarbon, food)) please contact our Technical Office on 01342 826836 for details.
776
Pumps
Heidolph
Silicon tubing
New
Tygon tubing
New
521-628
New
Three-stop
tubing
New
Three-stop tubing is supplied in lengths of 40cm. Extension tubing is supplied in lengths of 1m.
0.2
0.5
0.9
1.4
2.8
0.0050.12
0.0240.60
0.020.5
0.112.5
0.051.24
0.256.24
0.112.8
0.5613.9
0.338.2
1.6340.8
0.010.12
0.050.60
0.040.5
0.212.5
0.101.24
0.526.24
0.232.8
1.1613.9
0.688.2
3.4040.8
521-612
521-613
521-614
Price
POA
POA
POA
Extension tubing
Cat. No.
521-615
521-616
521-617
Price
POA
POA
POA
521-619
521-620
521-621
521-622
Price
POA
POA
POA
POA
POA
Extension tubing
Cat. No.
521-623
521-624
521-625
521-626
521-627
Price
POA
POA
POA
POA
POA
Silicon
Tygon
Cat. No.
Description
Price
521-628 Fitting for extension tubing (PTFE) for 0.2, 0.5, 0.9 and 1.4mm tubing
521-629 Fitting for extension tubing (PTFE) for 2.8mm tubing
POA
POA
The fittings for extension tubing are supplied in a pack size of one. Therefore a minimum of two should be ordered
to connect extension tubing on both sides of the three-stop tubing.
0.8
3.1
6.3
0.297.2
3.896.0
13.5336
0.67.2
8.096.0
28.0336
This is the same tubing as listed for the single-channel pump heads, please see previous page for pricing and ordering
details.
Other tubing sizes are available including, 1.7mm and 4.8mm. For details on these and other tubing materials
(Viton, PharMed, Tygon (hydrocarbon, food)) please contact our Technical Office on 01342 826836 for details.
777
Pumps
Watson Marlow
519-000
Instant changeover between manual and analogue auto control. Fitted with rapid tube loading 102R
pumphead which accepts silicone tubing.
Specification
Flow rate ranges (ml/min)
for tube bore, mm
at 1.0-32 rpm
Speed range, rpm
Dimensions (hxwxl), mm
Weight, kg
Standards
Cat. No.
0.5
0.8
1.6
3.2
4.8
0.0210.69 0.0481.61 0.2107.00 0.78026.0 1.59053.0
1.032
100x160x210
2.4
BS800, IEC 335-1, EN60529 (IP31), CE
Description
Price
POA
519-008
323S/D speed adjusts in 1rpm steps from 3 to 400rpm. Instantly reversible, rapid-loading flip-top
pumphead accepts seven tube sizes, keypad lock prevents tampering or accidental changes, auto restart
for mains failure recovery.
Specification
Flow rate ranges (ml/min)
tube bore
0.5
3.0-400rpm
0.0912
Speed range, rpm
Pumphead fitted
Dimensions (hxwxl), mm
Weight, kg
Standards
0.8
0.2128
1.6
3.2
4.8
0.81110 3.0400 6.6880
3.0400rpm
313D three roller pumphead
125x230x225
4.7
IEC 335-1, EN60529 (IP31), CE
Cat. No.
Description
519-008
519-030
519-031
519-032
519-033
* Order the drive only to enable 314MC or 318MC pumpheads to be fitted, see next page.
For tubing also see next page.
778
6.4
8.0
111400 152000
Price
POA
POA
POA
POA
POA
Pumps
Watson Marlow
Bioprene tubing
314MCX four-roller extension pumphead add one to 314MC for ten channel pumping
318MCX eight roller extension pumphead add one to 318MC for ten channel pumping
Cat. No.
Description
519-034
519-036
519-035
519-037
Price
POA
POA
POA
POA
Pumpsil Platinum
Silicone tubing
Double pump segment manifold pump tubing for 314MC and 318MC
microcassette pumpheads
314MC and 318MC pumphead flow rate ranges (ml/min) - maximum 10 channels. Note: Speed must
not exceed 110rpm.
Flow rates (ml/min) at 3.0-110 rpm for 323S and 323U drives
Orange/Blue 0.25mm
Orange/Yellow 0.50mm
Black/Black 0.76mm
Orange/Orange 0.88mm
Red/Red 1.14mm
314MC
0.010.5
0.051.7
0.134.6
0.176.4
0.279.9
Description
Colour code
Orange/Blue
Orange/Yellow
Black/Black
Orange/Orange
Red/Red
Grey/Grey
Yellow/Blue
Green/Green
Purple/Black
Purple/White
318MC
0.010.5
0.041.4
0.113.9
0.145.3
0.248.8
Grey/Grey 1.29mm
Yellow/Blue 1.52mm
Green/Green 1.85mm
Purple/Black 2.29mm
Purple/White 2.79mm
Cat. No.
Bore
0.25mm
0.50mm
0.76mm
0.88mm
1.14mm
1.29mm
1.52mm
1.85mm
2.29mm
2.79mm
Price
Marprene (Pack of 6)
519-047
519-049
519-051
519-053
519-055
519-057
519-059
519-061
519-063
519-065
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
314MC
0.3513
0.5219
0.7628
1.140
1.453
318MC
0.2710
0.3814
0.5520
0.7929
0.9836
Cat. No.
Price
Marprene tubing
POA
POA
POA
POA
POA
POA
POA
POA
POA
POA
Pumpsil
Platinum-cured Silicone tubing manufactured by Watson-Marlow.
Tighter bore and wall tolerances (no negative tolerance) ensure flow stability and accuracy
LaserTraceability, laser etched lot number full length of tubing ensures true traceability
Pumpsil meets or exceeds : USP class VI; European Pharmacopoeia 3.1.9; ISO 10993; FDA
regulations CFR 177.2600 for contact with food; USDA standards; 3A standards
Marprene
Cat. No. Bore, mm
519-011
519-012
519-013
519-014
519-015
519-016
519-017
0.5
0.8
1.6
3.2
4.8
6.4
8.0
Silicone
Price
POA
POA
POA
POA
POA
POA
POA
Bioprene
0.5
0.8
1.6
3.2
4.8
6.4
8.0
Price
POA
POA
POA
POA
POA
POA
POA
0.5
0.8
1.6
3.2
4.8
6.4
8.0
Price
POA
POA
POA
POA
POA
POA
POA
779
Pumps
Watson Marlow
New
519-084
Stackable
* Also accepts 520R 2.4mm wall tubing pumphead for maximum flow and other multi-channel pumphead options.
1.6
0.0497
3.2
4.8
6.4
8.0
0.18390 0.40870 0.701500 1.12400
158x276x385 (all models)/9.6 (all models)
135VA (all models)
CE, CETL US (all models)
Description
Price
New
519-085
POA
1.6
0.0497
3.2
4.8
6.4
8.0
0.18390 0.40870 0.701500 1.12400
158x276x385 (all models)/9.6 (all models)
135VA (all models)
CE, CETL US (all models)
Description
Price
New
519-086
POA
* Also accepts 520R2 pumphead for use with 2.4mm wall thickness tubing and other multi-channel pumphead options.
1.6
0.0497
3.2
4.8
6.4
8.0
0.18390 0.40870 0.701500 1.12400
158x276x385 (all models)/9.6 (all models)
135VA (all models)
CE, CETL US (all models)
Description
780
Price
POA