Documente Academic
Documente Profesional
Documente Cultură
Lecture Notes
Transmission Basics
In data networking, the term transmit means to issue signals to the network medium. Transmission refers to either
the process of transmitting or the progress of signals after they have been transmitted.
Whereas amplitude indicates an analog waves strength, frequency is the number of times that a waves amplitude
cycles from its starting point, through its highest amplitude and its lowest amplitude, and back to its starting point
over a fixed period of time. Frequency is expressed in cycles per second, or hertz (Hz). The distance between
corresponding points on a waves cycle is called its wavelength. Wavelength can be expressed in meters or feet. A
waves wavelength is inversely proportional to its frequency.
The term phase refers to the progress of a wave over time in relationship to a fixed point. Figure 3-2 on page 76 of
the text illustrates waves with identical amplitudes and frequencies whose phases are 90 degrees apart.
14
One benefit to analog signals is that, because they are more variable than digital signals, they can convey greater
subtleties with less energy.
However, because voltage is varied and imprecise in analog signals, analog transmission is more susceptible to
transmission flaws such as noise, or any type of interference that may degrade a signal, than digital signals. Now
contrast the analog signals pictured in Figure 3-1 through 3-3 to a digital signal, as shown in Figure 3-4 on page 78 of
the text.
Digital signals are composed of pulses of precise, positive voltages and zero voltages. A pulse of positive voltage
represents a 1. A pulse of zero voltage represents a 0. As in any binary system, these 1s and 0s combine to encode
information. Every pulse in the digital signal is called a binary digit, or bit. A bit can have only one of two possible
values: 1 or 0. Eight bits together form a byte.
15
Data Modulation
Data modulation is a technology used to modify analog signals in order to make them suitable for carrying data over
a communication path. In modulation, a simple wave, called a carrier wave, is combined with another analog signal
to produce a unique signal that gets transmitted from one node to another.
Modulation can be used to make a signal conform to a specific pathway, as in the case of frequency modulation
(FM) radio, in which the data must travel along a particular frequency. In frequency modulation, the frequency of the
carrier signal is modified by the application of the data signal. In amplitude modulation (AM), the amplitude of the
carrier signal is modified by the application of the data signal. Figure 3-5 on page 80 of the text depicts an unaltered
carrier wave, a data wave, and the combined wave as modified through frequency modulation.
Transmission Direction
Data transmission, whether analog or digital, may also be characterized by the direction in which the signals travel
over the media.
16
Multiplexing
A form of transmission that allows multiple signals to travel simultaneously over on medium is known as
multiplexing. In order to carry multiple signals, the mediums channel is logically separated into multiple smaller
channels, or subchannel. For each type of multiplexing, a device that can combine many signals on a channel, a
multiplexer (mux), is required at the sending end of the channel. At the receiving end, a demultiplexer (demux)
separates the combined signals and regenerates them in their original form.
Multiplexing is commonly used on networks to increase the amount of data that can be transmitted in a given time
span. For example, one type of multiplexing, time division multiplexing (TDM), divides a channel into multiple
intervals of time, or time slots. Figure 3-7 on page 82 of the text shows a simple TDM model.
Statistical multiplexing is similar to time division multiplexing, but rather than assigning a separate slot to each
node in succession, the transmitter assigns slots to nodes according to priority and need.
Wavelength division multiplexing (WDM) is a technology used with fiber-optic cable. In fiber-optic transmission,
data is represented as pulses of light, rather than pulses of electric current. Figure 3-9 on page 83 of the text illustrates
WDM transmission.
17
The form of WDM used on most modern fiber-optic networks is dense wave division multiplexing (DWDM). In
DWDM, a single fiber in a fiber-optic cable can carry between 80 and 160 channels.
18
Often, the term bandwidth is used interchangeably with throughput, and in fact, this may be the case on the
Network+ certification exam. Bandwidth and throughput are similar concepts, but strictly speaking, bandwidth is a
measure of the difference between the highest and lowest frequencies that a medium can transmit.
Transmission Flaws
Both analog and digital signals are susceptible to degradation between the time they are issued by a transmitter and
the time they are received.
Noise
A common source of noise is electromagnetic interference (EMI), or waves that emanate from electrical devices or
cables carrying electricity. One type of EMI is radiofrequency interference (RFI), or electromagnetic interference
caused by radio waves. Another form of noise that hinders data transmission is crosstalk. Crosstalk occurs when a
signal traveling on one wire or cable infringes on the signal traveling over an adjacent wire or cable.
Attenuation
Another transmission flaw is attenuation, or the loss of a signals strength as it travels away from its source. To
compensate for attenuation, both analog and digital signals are strengthened en route so they can travel farther.
However, the technology used to strengthen an analog signal is different from that used to strengthen a digital signal.
Analog signals pass through an amplifier.
19
Latency
Although electrons travel rapidly, they still have to travel, and a brief delay takes place between the moment you
press the key and the moment the server accepts the data. This delay is called latency. The most common way to
measure latency on data networks is by calculating a packets round trip time (RTT), or the length of time it takes
for a packet to go from sender to receiver, then back from receiver to sender. RTT is usually measured in
milliseconds.
Media Characteristics
Generally speaking, you will consider five characteristics when choosing a data transfer media: throughput, cost, size
and scalability, connectors, and noise immunity.
Throughput
Perhaps the most significant factor in choosing a transmission method is its throughput. All media are limited by the
laws of physics that prevent signals from traveling faster than the speed of light. Beyond that, throughput is limited
by the signaling and multiplexing techniques used in a given transmission method.
Cost
The following variables can all influence the final cost of implementing a certain type of media:
Cost of installation
Cost of new infrastructure versus reusing existing infrastructure
Cost of maintenance and support
Cost of a lower transmission rate affecting productivity
Cost of obsolescence
20
Connectors
Connectors are the pieces of hardware that connect the wire to the network device, be it a file server, workstation,
switch, or printer. Every networking medium requires a specific kind of connector.
Noise Immunity
On most networks, noise is an ever-present threat, so you should take measures to limit its impact on your network.
For example, you should install cabling well away from powerful electromagnetic forces. It is also possible to use
anti-noise algorithms to protect data from being corrupted by noise. If these measures dont ward off interference,
you may need to use a metal conduit, or pipeline, to contain and further protect the cabling.
Coaxial Cable
Coaxial cable, called coax for short, was the foundation for Ethernet networks in the 1980s and remained a
popular transmission medium for many years.Coaxial cable consists of a central copper core surrounded by an
insulator, a braided metal shielding, called braiding, and an outer cover, called the sheath or jacket. Figure 3-13 on
page 94 of the text depicts a typical coaxial cable.
Coaxial cabling comes in hundreds of specifications, although you are likely to see only two or three types of coax in
use on data networks. The significant differences between the cable types lie in the materials used for their center
cores, which in turn influence their impedance, throughput, and purpose.
Quick Reference
In a Thicknet network, a nodes Ethernet interface, a port on the devices NIC, is connected with the drop cable via an
AUI connector or an n-series connector. AUI (Attachment Unit Interface) is an Ethernet standard that establishes
physical specifications for connecting coaxial cables with transceivers and networked nodes.
21
A Thicknet network also must abide by the 5-4-3- rule of networking. This rule says that, between two
communicating nodes, the network cannot contain more than five network segments connected by four repeating
devices, and no more than three of the segments may be populated (up to two may be unpopulated). Figure 3-15 on
page 96 of the text illustrates the 5-4-3 rule, which also applies to other 10-Mbps versions of Ethernet running over
copper cable.
22
Quick Reference
Both Thicknet and Thinnet coaxial cable rely on the bus topology, in which nodes share one uninterrupted channel.
Networks using the bus topology must be terminated at both ends. Without terminators, signals on a bus network
would travel endlessly between the two ends of the network, a phenomenon known as signal bounce. Figure 3-17 on
page 98 of the text depicts a 10Base2 network using a bus topology.
Twisted-Pair Cable
Twisted-pair cable consists of color-coded pairs of insulated copper wire, each with a diameter of 0.4 to 0.8 mm, or
approximately the diameter of a straight pin. Figure 3-18 on page 99 of the text illustrates how the number of pairs in
a cable varies, depending on the cable type.
23
The more twists per inch in a pair of wires, the more resistant the pair will be to all forms of noise. Higher-quality,
more expensive twisted-pair cable contains more twists per foot. The number of twists per meter or foot is known as
the twist ratio.
24
Quick Reference
Discuss the different categories of cable as listed on pages 101 through 103 of
the text.
10BaseT
10baseT is a popular Ethernet networking standard that replaced the older 10Base2 and 10Base5 technologies. The
10 represents its maximum throughput of 10 Mbps, the Base indicates that it uses baseband transmission, and the
T stands for twisted pair, the medium it uses.
Fault tolerance is the capacity for a component or system to continue functioning despite damage or partial
malfunction. Use of the star topology also makes 10BaseT networks easier to troubleshoot, because you can isolate
problems more readily when every device has a separate connection to the LAN. 10BaseT, like 10Base2 and
10Base5, also follows the 5-4-3 rule of networking and is subject to a distance limitation. The maximum distance that
a 10BaseT segment can traverse is 100 meters. Figure 3-22 on page 104 of the text depicts a 10BaseT Ethernet
network with maximum segment lengths.
25
As with 10BaseT, nodes on a 100BaseT network are configured in a star topology. 100BaseT networks do not follow
the 5-4-3 rule. Two 100BaseT specifications100BaseT4 and 100BaseTXhave competed for popularity as
organizations move to 100-Mbps technology. 100BaseTX is the version you are most likely to encounter. It achieves
26
Throughput
Connector
Size and scalability
Cost
Noise immunity
Quick Quiz
1.
2.
____________ is a term used by networking professionals to describe the non-data information that must
accompany data in order for a signal to properly routed and interpreted by the network.
3.
___________ is the measure of how much data is transmitted during a given period of time.
4.
___________ occurs when a signal traveling on one wire or cable infringes on the signal traveling over and
adjacent wire or cable.
5.
___________ may be used for 16 Mbps Token Ring or 10 Mbps Ethernet networks.
Fiber-Optic Cable
Fiber-optic cable, or simply fiber, contains one or several glass or plastic fibers at its center, or core. Data is
transmitted via pulsing light sent from a laser or light-emitting diode (LED) through the central fibers. Surrounding
the fibers is a layer of glass or plastic called cladding. Figure 3-25 on page 107 of the text shows the different layers
of a fiber-optic cable.
27
The most significant drawback to the use of fiber is its relatively high cost. Another disadvantage is that most fiberoptic networks transmit data in uni-directionally over the fiber; therefore, each cable must contain at least two strands
one to send data and one to receive it.
100BaseFX
The 100BaseFX standard specifies a network capable of 100-Mbps throughput that uses baseband transmission and
fiber-optic cabling. 100BaseFX requires multimode fiber containing at least two strands of fiber. 100BaseFX, like
100BaseT, is also considered Fast Ethernet. Organizations switching, or migrating, from UTP to fiber media can
combine 100BaseTX and 100Base FX within one network. In order to do this, transceivers in computers and
connectivity devices must have both RJ-45 and SC or ST ports.
28
1000BaseLX
Probably the most common 1-Gigabit Physical layer standard in use today is 1000BaseLX. The 1000 in
1000BaseLX stands for 1000 Mbpsor 1 Gbpsthroughput. Base stands for baseband transmission, and LX
represents its reliance on long wavelengths of 1300 nanometers.
1000BaseSX
1000BaseSX is similar to 1000BaseLX in that it has a maximum throughput of 1 Gbps. However, it relies on only
multimode fiber-optic cable as its medium. Another difference is that 1000BaseSX uses short wavelengths of 850
nanometersthus, the SX, which stands for short.
Entrance facilities
Equipment room
Horizontal wiring
Backbone wiring
Telecommunications closet
Work area
Installing Cable
Many network problems can be traced to poor cable installation techniques. For example, if you dont crimp twistedpair wires in the correct position in an RJ-45 connector, the cable will fail to transmit or receive data (or bothin
which case, the cable will not function at all). Installing the wrong grade of cable can either cause your network to
fail or render it more susceptible to damage.
30
31
If you terminate the RJ-45 plugs at both ends of a patch cable identically, following one of the TIA/EIA 568
standards, you will create a straight-through cable. A straight-through cable is so named because it allows signals to
pass straight through between terminations. However, in some cases you may want to reverse the pin locations of
some wiresfor example, when you want to connect two workstations without using a connectivity device or when
you want to connect two hubs. This can be accomplished through the use of a crossover cable, a patch cable in
which the termination locations of the transmit and receive wires on one end of the cable are reversed, as shown in
Figure 3-36 on page 119 of the text.
32
Quick Reference
Discuss the cable installation tips that will help prevent Physical layer failures
listed on page 120 of the text.
Wireless Transmission
Networks that transmit signals through the atmosphere are known as wireless networks or wireless LANs (WLANs).
Wireless LANs typically use infrared or radiofrequency (RF) signaling.
33
Antennas
A services specifications determine the antennas power output, frequency, and radiation pattern. An antennas
radiation pattern describes the relative strength over a three-dimensional area of all the electromagnetic energy the
antenna sends or receives.
A directional antenna issues wireless signals along a single direction. This type of antenna is used when the source
needs to communicate with one destination, as in a point-to-point to link. In contrast, an omni-directional antenna
issues and receives wireless signals with equal strength and clarity in all directions. This type of antenna is used when
many different receivers must be able to pick up the signal, or when the receivers location is highly mobile.
Signal Propagation
Ideally, a wireless signal would travel directly in a straight line from its transmitter to its intended receiver. This type
of propagation, known as line-of-sight (LOS), uses the least amount of energy and results in the reception of the
clearest possible signal. Reflection in wireless signaling is no different from reflection of other electromagnetic
waves, such as light. The wave encounters an obstacle and reflectsor bounces backtoward its source.
In diffraction, a wireless signal splits into secondary waves when it encounters an obstruction. The secondary waves
continue to propagate in the direction in which they were split. Scattering is the diffusion, or the reflection in
multiple different directions, of a signal. Scattering occurs when a wireless signal encounters an object that has small
dimensions compared to the signals wavelength.
Because of reflection, diffraction, and scattering, wireless signals follow a number of different paths to their
destination; such signals are known as multi-path signals. Figure 3-39 on page 124 of the text illustrates multi-path
signals caused by these three phenomena.
34
Signal Degradation
No matter what paths wireless signals take, they are bound to run into obstacles. When they do, the original signal
issued by the transmitter will experience fading, or a change in signal strength as a result of some of the
electromagnetic energy being scattered, reflected, or diffracted after being issued by the transmitter.
Interference can distort and weaken a wireless signal in the same way that noise distorts and weakens a wire-bound
signal. However, because wireless signals cannot depend on a conduit or shielding to protect them from extraneous
EMI, they are more vulnerable to noise.
35
Infrared Transmission
Infrared signals are transmitted by frequencies in the 300 GHz to 300,000 GHz range, which is just above the top of
the wireless spectrum as it is defined by the FCC. Infrared frequencies approach the range of visible light in the
electromagnetic spectrum, and in fact, some can be seen. On computer networks, infrared transmission is most often
used for communications between devices in the same room.
An access point (AP) is a device that accepts wireless signals from multiple nodes and retransmits them to the rest of
the network. To cover its intended range, an access point must have sufficient power and be strategically placed so
that stations can communicate with it. It is common for a WLAN to include several access points. The number of
access points depends on the number of stations a WLAN connects. The maximum number of stations each access
point can serve varies from 10 to 100, depending on the wireless technology used.
Distance
Existing infrastructure
Quick Quiz
1.
2.
___________ is the degradation of the light signal after it travels a certain distance away from its source.
3.
The ___________ standard does not use fiber-optic cable, but instead uses twinaxial copper wiring.
4.
A(n) ___________ is a panel of data receptors into which horizontal cabling from the workstations is inserted.
5.
A(n) ___________ is a device that accepts wireless signals from multiple nodes and retransmits them to the rest
of the network.
Discussion Questions
1.
2.
37