Documente Academic
Documente Profesional
Documente Cultură
User Manual
G03
VoIP Terminal Adapter
User Manual
G03 VoIP TA
User Manual
1
2
3
4
5
6
Introduction ................................................................................................................................... 3
1.1
Hardware Overview............................................................................................................ 3
1.2
Software Overview............................................................................................................. 3
IVR Interface for The TA................................................................................................................ 4
Setup the TA by Web Browser....................................................................................................... 4
3.1
Login.................................................................................................................................. 5
3.2
System Information ............................................................................................................ 5
3.3
Phone Book ....................................................................................................................... 5
3.4
Phone Settings................................................................................................................... 6
3.5
Network............................................................................................................................ 12
3.6
SIP Settings ..................................................................................................................... 16
3.7
NAT Trans. ....................................................................................................................... 20
3.8
Others.............................................................................................................................. 20
3.9
System Auth..................................................................................................................... 21
3.10 Save Change ................................................................................................................... 22
3.11 Update ............................................................................................................................. 22
3.12 Reboot ............................................................................................................................. 23
Setup the TA by using Console (Hyper Terminal) ........................................................................ 23
4.1
Configuration ................................................................................................................... 24
4.2
Using CLI command to configure the TA .......................................................................... 24
How to make a phone call........................................................................................................... 30
Get a FWD account .................................................................................................................... 30
G03 VoIP TA
User Manual
Introduction
This users manual is for G03 VoIP terminal adapter (TA). This users manual will explain the IVR
instruction, web configuration and command line configuration for the TA. Before using the TA, some setup
processes are required to make the TA work properly.
1.1
Hardware Overview
The TA has Networking interfaces, telephone interfaces, LED indication, power connector and Reset
button.
1.1.1 Two RJ-45 Networking interfaces, these two interfaces support 10/100Mps Fast Ethernet. you can
connect one RJ-45 Fast Ethernet port to the ADSL or Switch, and connect the other one to your
computer.
1.1.2 Two RJ-11 Type analog telephone jack interfaces. Both Phone1 and Phone2 are for user to connect to a
phone set.
1.1.3 LED Indication: There are five LED indicators in the TA to show the Power, network, and Off-Hook
indication.
1.1.4 Reset Button: Press Reset button for longer than 5 seconds to make the TA restore factory default
settings and reboot. If TA works improperly, please make an attempt to Reset and then configure again.
1.2
Software Overview
Network Protocol
SIP v1 (RFC2543), v2(RFC3261)
IP/TCP/UDP/RTP/RTCP
IP/ICMP/ARP/RARP/SNTP
TFTP Client/DHCP Client/ PPPoE Client
Telnet/HTTP Server
DNS Client
NAT/DHCP Server
Codec
G.711: 64k bit/s (PCM)
G.723.1: 6.3k / 5.3k bit/s
G.726: 16k / 24k / 32k / 40k bit/s (ADPCM)
G.729A: 8k bit/s (CS-ACELP)
G.729B: adds VAD & CNG to G.729
Voice Quality
VAD: Voice activity detection
CNG: Comfortable noise generator
LEC: Line echo canceller
Packet Loss Compensation
Adaptive Jitter Buffer
Call Function
Call Hold
Call Waiting
Call Forward
Caller ID
3-way conference
DTMF Function
In-Band DTMF
Out-of Band DTMF
SIP Info
Tone
Ring Tone
Ring Back Tone
Dial Tone
Busy Tone
Programming Tone
Phone Function
Volume Adjustment
Speed dial key
Phone book
Flash
IP Assignment
Static IP
DHCP
PPPoE
Security
HTTP 1.1 basic/digest authentication for Web setup
MD5 for SIP authentication (RFC2069/ RFC 2617)
QoS
ToS field
NAT Traversal
STUN
Configuration
Web Browser
Console/Telnet
IVR/Keypad
Firmware Upgrade
SIP Server
G03 VoIP TA
User Manual
TFTP
Console
HTTP
Group
IVR Action
Parameter(s)
Function
Reboot
#195#
None
Function
Factory Reset
#198#
None
Info
Check
Address
#120#
None
Info
Check IP Type
#121#
None
#122#
None
#123#
None
#124#
None
#125#
None
#128#
None
None
IP
Info
Info
Info
Info
Info
Setting
#111#
Setting
Set Static
Address
#112xxx*xxx*xxx*xxx#
Setting
Set
Mask
Setting
Set Gateway IP
Address
#114xxx*xxx*xxx*xxx#
Setting
#115xxx*xxx*xxx*xxx#
Setting
Set Codec
#130+[1-8]#
Setting
Setting
IP
Network
Set
Handset
Gain
Set
Handset
Volume
#113xxx*xxx*xxx*xxx#
#131+[00~15]#
#132+[00~12]#
Notes:
After you hear Option Successful,
hang-up. The system will reboot
automatically.
System will automatically Reboot.
WARNING: ALL User-Changeable
NONDEFAULT SETTINGS WILL
BE LOST! This will include network
and service provider data.
IVR will announce the current IP
address of the TA
IVR will announce if DHCP in
enabled or disabled.
IVR will announce current in use
VoIP number
IVR will announce the current
network mask of the TA.
IVR will announce the current
gateway IP address of the TA.
IVR will announce the current
setting in the Primary DNS field.
IVR will announce the version of the
firmware running on the TA.
The system will change to DHCP
Client type
DHCP will be disabled and system
will change to the Static IP type.
By default, NAT is on, LANs ip is 192.168.123.1(dial #120# to check LANs ip), WAN is DHCP
client(dial #126# to check WANs ip).
3
G03 VoIP TA
User Manual
WAN is DHCP client (dial #126# to check WANs ip). You have to set your PC in the same subnet with TA in
order to connect them with each other.
3.1
Login
Please input the username and password into the blank field. The default setting is:
1. For Administrator, the username is: root; and the password is: test. If you use this account to login,
you can configure all the settings.
2. For normal user, the username is: user; and the password is: test. If you use this account to login,
but you can not configure the SIP setting.
Click the Login button will move into the TA web based management information page.
If you change the setting in the Web Management interface, please do remember to click the Submit
button in that page. After you finished the change of the setting, click the Save function in the left side, and
click the Save Button. When you finished the setting, please click the Reboot function in the left side, and
click the Reboot button in that page. After the system restart, all the setting can work properly.
3.2
System Information
When you login, you can see the TAs current system information like firmware version, model name etc
in this page.
Also you can see the function lists in the left side. You can use mouse to click the function you want to
set up.
3.3
Phone Book
In Phone Book function, you can setup the Phone Book. The phone book can store up to 140 groups of
number.
G03 VoIP TA
User Manual
3.3.1.2 To delete a group of number, first select the number, and then click Delete Selected button to delete
selected number.
3.3.1.3 To delete all number, click Delete All button, a dialogue window will show up. Click OK button to
delete all numbers.
3.4
Phone Settings
Phone Setting contains Call Forward, SNTP Settings, Volume Settings, DND Settings, Caller ID, Flash
Time Settings, Call Waiting Settings and T.38(Fax) Settings.
G03 VoIP TA
User Manual
3.4.1
Call Forward: you can setup the phone number you want to forward to in this page. There are three type
of Forward mode. You can choose between All Forward, Busy Forward, and No Answer Forward by click
the corresponding icon.
3.4.1.1 All Forward: All incoming call will forward to the number you choosed. You can input the name and the
phone number in Name and URL field.
3.4.1.2 Busy Forward: If you are on the phone, the new incoming call will forward to the number you choosed.
You can input the name and the phone number in Name and URL field.
3.4.1.3 No Answer Forward: If you can not answer the phone, the incoming call will forward to the number you
choosed. You can input the name and the phone number in Name and URL field. Also you have to set
No Answer Fwd Time Out for system to start to forward the call to the number you choosed.
When you finished the setting, please click the Submit button.
G03 VoIP TA
User Manual
3.4.2
SNTP Settings: you can setup the primary and secondary SNTP Server to get the date/time information.
Also you can base on your location to set the Time Zone, and how long is needed to synchronize. When
you finished the setting, please click the Submit button.
3.4.3
Volume Settings: you can setup the Handset Volume, PSTN-Out Volume, Handset Gain and PSTN-In
Gain. When you finished the setting, please click the Submit button.
3.4.3.1 Handset Volume is to set the volume for you to hear from the handset.
3.4.3.2 Handset Gain is to set the gain send out to the other side.
G03 VoIP TA
User Manual
3.4.4
DND Setting function: you can setup the Block Setting to keep the phone slience. You can choose DND
Always or DND a period. When you finished the setting, please click the Submit button.
3.4.4.1 DND Always: All incoming call will be blocked until disable this feature.
3.4.4.2 DND Period: Set a time period and the phone will be blocked during the time period. If the From time
is large than the To time, the To time will be regarded as next days time.
3.4.5
Caller ID function: you can set the device to show Caller ID in your PSTN Phone or IP Phone. There are
four selection of Caller ID. You need to base on your environment to set the Caller ID function for FSK or
DTMF.
G03 VoIP TA
User Manual
3.4.6
Dial Plan: This function provides basic dial number replacement rule.
Drop prefix: If No, when the number you dialed beginns with the number in right blank, the number in left
blank will be added automatically before your dialed number. If Yes, when the number you dialed beginns
with the number in right blank, the number will be replaced with the number in left blank.
Auto Dial Time: the number you dialed will be sent out automatically after the time you set here.
10
G03 VoIP TA
User Manual
When your dialed number beginns with 5 or 35, 21, and is 4 digits, 007 will be added to the beginning of
your dialed number.
3.4.7
Flash Time Setting function: When you use a PSTN Phone, you need press the Hook to do the Flash
(Switch to another phone line or HOLD). This function is for you to set the max time you press the Hook
to activate the Flash function.
3.4.8
Call Waiting Setting function: You can Enable/Disable the Call Waiting function, When you are talking
with someone, there is a new incoming call, you will hear the call waiting tone.
3.4.9
T.38(Fax) Setting: Enable/disable the fax function and set fax port.
11
G03 VoIP TA
User Manual
If enabled, when you lift handset, the hot line number will be dialed out automatically.
3.4.11 Alarm setting
Network
In Network you can check the Network status, configure the Network Settings, DDNS settings and VLAN
settings.
12
G03 VoIP TA
User Manual
3.5.1
Network Status: You can check the current Network setting in this page.
13
G03 VoIP TA
User Manual
3.5.3
LAN Settings: Set network parameters for LAN.You may refer to your current network environment to
configure the TA properly. When you finished the setting, please click the Submit button.
3.5.4
DDNS Setting: You can configure the DDNS setting in this page. You need to have the DDNS account
and input the informations properly. If you have a DDNS account with a public IP address, others can call
you via the DDNS account. But now most of the VoIP applications work with a SIP Proxy Server. When
you finished the setting, please click the Submit button.
14
G03 VoIP TA
User Manual
3.5.5
VLAN Settings
3.5.6
DMZ setting
15
G03 VoIP TA
User Manual
3.5.7
3.6
Virtual Server
SIP Settings
In SIP Settings you can setup the Service Domain, Port Settngs, Codec Settings, Codec ID Setting,
DTMF Setting, RPort Setting and Other Settings. If the VoIP service is provided by ISP, you have to setup the
related informations correctly so that you can register to the SIP Proxy Server successfully.
3.6.1
In Service Domain Function you need to input the account and the related informations in this page.
Please refer to your ISP provider. You can register three SIP accounts in the TA. You can dial the VoIP
phone to your friends via first enabled SIP account and receive phone from these three SIP accounts.
16
G03 VoIP TA
User Manual
3.6.2
Port Settings: you can setup the SIP and RTP port number in this page. Each ISP provider will have
different SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you
finished the setting, please click the Submit button.
17
G03 VoIP TA
User Manual
3.6.3
Codec Settings: you can setup the Codec priority, RTP packet length, and VAD function in this page. You
need to follow the ISP suggestion to setup these items. When you finished the setting, please click the
Submit button.
3.6.4
Codec ID Setting: Sometimes 2 VoIP devices with different Codec ID will cause some problems. If there
are some problems when you are talking with others, you may ask the other one what Codec ID he is
useing, and change your Codec ID to the same as his. When you finished the setting, please click the
Submit button.
18
G03 VoIP TA
User Manual
3.6.5
DTMF Setting: Choose between 2833, Inband DTMF and Send DTMF SIP Info. Please refer to your ISP
for correct setting. When you finished the setting, please click the Submit button.
3.6.6
RPort Setting: Enable/Disable RPort. To change this setting, please following your ISPs information.
When you finished the setting, please click the Submit button.
3.6.7
Other Settings: you can setup the Hold by RFC, Voice/SIP QoS and SIP expire time in this page. To
change these settings please following your ISPs information. The QoS setting is to set the voice
packets priority. If you set the value higher, the voice packets will get higher priority. But the QoS function
still need to cooperate with the others Internet devices. When you finished the setting, please click the
Submit button.
19
G03 VoIP TA
User Manual
3.7
3.7.1
3.8
NAT Trans.
STUN Setting: you can setup the STUN Enable/Disable and STUN Server IP address in this page. This
function can help your TA working properly behind NAT. To change these settings please following your
ISP information. When you finished the setting, please click the Submit button.
Others
3.8.1
3.8.2
FXS Port Setting: Please set this according to your countrys standard.
20
G03 VoIP TA
User Manual
3.8.3
3.8.4
Tones Settings
3.8.5
Advanced Settings
3.9
System Auth.
In System Authority you can change your login name and password. When you finished the setting,
please click the Submit button.
21
G03 VoIP TA
User Manual
3.11 Update
In Update you can update the IP Phones firmware to the latest or restore the factory setting.
3.11.1 In New Firmware function you can update new firmware via Local PC/TFTP in this page. You can ugrade
the firmware by the following steps:
1)
2)
Click the Browse button in the right side of the File Location, or you can type the correct path
and the filename in File Location blank.
3)
Select the correct file you want to download to the IP Phone then click the Update button.
22
G03 VoIP TA
User Manual
3.11.3 In Default Setting you can restore the VoIP Phone to factory default in this page. You can just click the
Restore button, and then the VoIP Phone will restore to default and automatically restart.
3.12 Reboot
Click the Reboot button, then the TA will reboot automatically.
23
G03 VoIP TA
User Manual
4.1
Configuration
Open the hyper terminal window, input a connection name and click OK button. Select
TCP/IP(WinSock) in Connect using field, input TAs IP in Host address field, Port number use the default
value 23. Finally click OK.
A login window will show up. Input your user name after Login: and password after Password:. If user
name and password are correct, it will prompt Login Correct, otherwise will prompt Login Incorrect.
4.2
4.2.1
Description
Show CLI Command
ARP Configuration
Interface Configuration
24
G03 VoIP TA
User Manual
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
save
reboot
exit
debugmode
update
auth
nat
dns
ping
sip
ddns
sntp
vlan
time
mactab
dump
book
reload
watchdog
phone
weblogo
dsp
addport
cid
slic
ver
Save to flash
Reboot
Exit
Enter Debug Mode
Update Flash Code/RAM
Change User Name and Password
NAT Configuration
DNS Configuration
ping [-lN] [IP-addr|host-name]
SIP Configuration
DDNS Configuration
SNTP Configuration
VLAN Configuration
Get System Time
Show MAC Learning Table
Read/Write Memory
Edit phone book
Reload Factory Setting
WatchDog Function
Phone Setting
Change Web'
s logo
Show dsp type
Add Nat Port Mapping
Select slic Cid
read or write slic registers
Firmware Version
4.2.1.1
4.2.1.2
arp function
Itno
1
2
3
4
5
4.2.1.3
Command
?
-a
-d
-s
(null)
Description
Show '
arp'Option
Show ARP Table
Delete ARP Table
Set Static ARP Table
Show ARP Table
ipconfig function
Itno
Command
1
?
2
-if0
3
-if1
4
-if2
5
-h
6
-a
7
-r
8
(null)
Description
Show '
ipconfig'Option
Interface 0
Interface 1
Interface 2
Set Host Name
Set ARP Cache Expire
Restore Current Setting
Show IP Setting
N is 0, 1, 2
Description
Show '
ipconfig -ifN'Option
Set Host Type
Set MAC Address
Set IP Address
Set Net Mask
25
G03 VoIP TA
User Manual
6
7
8
9
10
11
12
13
14
15
16
17
18
19
4.2.1.4
save function
Itno
1
2
3
-g
-dns0
-dns1
-dr
-nat
on
off
-dhcps
-ddns
-bridge
-dev0
-dev1
-dev2
(null)
Set Gateway
Set Primary DNS server
Set Secondary DNS server
Set Default Route
Set NAT
Enable Interface
Disable Interface
DHCP Server Setting
Set DDNS
Set Bridge
Set Device 0 Setting
Set Device 1 Setting
Set Device 2 Setting
Show Interface Setting
Command
?
-book
-sys
Description
Show '
save'Option
Save phone book
Save system setting
4.2.1.5
4.2.1.6
4.2.1.7
4.2.1.8
update function
Itno
1
2
3
4
5
6
Command
Description
?
Show '
update'Option
-os
Update OSImage(IP filename)
-dsp
Update DSP Image(IP filename)
-all
Update All Image(IP filename)
-server
Update Server (IP filename length)
-pcm
PCM(IP filename)
-alaw
alaw (IP filename)
-ulaw
ulaw (IP filename)
-g729
g729 (IP filename)
-g723
g723 (IP filename)
-g726.16
g726.16 (IP filename)
-g726.24
g726.24 (IP filename)
-g726.32
g726.32 (IP filename)
-g726.40
g726.40 (IP filename)
IP is the TFTP servers IP address, and the filename is the image you want to download into the
system.
4.2.1.9
auth function
Itno
1
2
3
4
Command
?
-user
-pass
(null)
Description
Show '
auth'Option
Change User Name.'
auth -sys3 -user xxx '
Change Password. '
auth -sys3 -pass xxx xxx'
Show auth'
s System/PPP Setting
Description
Show '
auth'Option
26
G03 VoIP TA
User Manual
2
-admin
Change Administrator user name/password
3
-sys0
Change System user0 user name/password
4
-sys1
Change System user1 user name/password
5
-sys2
Change System user2 user name/password
6
-sys3
Change System user3 user name/password
7
-sys4
Change System user4 user name/password
8
-norm0
Change Normal user0 user name/password
9
-norm1
Change Normal user1 user name/password
10
-norm2
Change Normal user2 user name/password
11
-norm3
Change Normal user3 user name/password
12
-norm4
Change Normal user4 user name/password
13
-ppp
Change PPP user name/password
14
(null)
Show auth Setting
If you want to change the password, you need to type the password twice in the CLI.
4.2.1.10 nat function
Itno
1
2
3
4
Command
?
-vs
-dmz
(null)
Description
Show '
nat'Option
Set '
nat -vs'Option
Set '
nat -dmz'Option
Show NAT Setting
Description
Show '
nat -dmz'Option
Enable DMZ
Enable DMZ
Set DMZ IP address
Show DMZ Setting
Command
?
-q
(null)
Description
Show '
dns'Option
DNS query. dns -q domain-name
Show DNS Table
Command
?
-l
(null)
Description
Show '
ping'Option
ping [-l N] [IP-addr|host-name]
ping [IP-addr|host-name]
Command
?
-proxy0
-proxy1
-proxy2
-upnp
-exts
-extr
-sipp
-rtpp
-stun
-rport
Description
Show '
sip'Option
sip -proxy0
sip -proxy1
sip -proxy2
sip -upnp on/off/show
sip -exts sip upnp external-port
sip -extr rtp upnp external-port
sip udp port
sip rtp port
sip -stun on/off
sip -rport on/off
27
G03 VoIP TA
User Manual
12
13
14
15
16
17
18
19
20
21
22
23
24
-sserver
-out
-dump
-log
-drtp
-rtpnc
-wanip
-nattype
-hbyrfc
-dereg
-restart
-jbt
(null)
Command
?
-type
-host
-wild
-mx
-backmx
-offline
-user
-pass
(null)
Description
Show '
ddns'Option
Set DDNS Type
Set Host Name
Set Wild Card Mode
Set Mail Exchanger
Set Mail Exchanger Mode
Set Offline Mode
Set Login User Name
Set Login Password
Show DDNS Setting
Command
?
-on
-off
-ip1
-ip2
-mode
-zone
-adjust
(null)
Description
Show '
sntp'Option
Enable SNTP Client
Disable SNTP Client
Set SNTP Server1 IP
Set SNTP Server2 IP
Set SNTP Client Mode
Set GMT Time Zone: [+|-][hour]:[min]
Set Adjustment Time: [second]
Show SNTP Setting
Command
?
-tx
-rx
(null)
Description
Show '
vlan'Option
Tx Vlan setting
Rx Vlan setting
Show Vlan Setting
Command
?
-t
-d
(null)
Description
Show '
Time'Option
Modify Time: hour:min:sec
Modify date: year:mon:date
Show Data & Time
28
G03 VoIP TA
User Manual
Command
?
-r
-w
Description
Show '
dump'Option
dump -r XXXXxxxx
dump -w XXXXxxxx XX
Command
?
-a
-c
-s
-p
Description
Show '
book'Option
Show answer list
Show call list
speed dial
phone book
4.2.1.21 reload function is to Reload Factory Setting, please make sure you want to do the factory reset.
4.2.1.22 watchdog function
Itno
Command
1
?
2
on
3
off
4
(null)
Description
Show '
WatchDog'Option
Enable WatchDog
Disable WatchDog
Show WatchDog Setting
Description
Show '
phone'Option
phone auto answer
Volume setting
Block Incoming call
Set Melody Ringer
Auto-forward Incall to Phone[0-9] in Book
Show Phone Setting
Command
?
-autoanswer
-vol
-block
-ring
-forward
(null)
Description
Show '
weblogo'Option
Vender Logo
Crystal media Logo
Show weblogo Setting
Command
?
-off
-1
-2
-3
-4
-5
-time
-single
(null)
Description
Show '
cid'Option
Disable Slic Cid signal
Tx FSK after 1st Ring
Tx FSK before 1st Ring
Tx DTMF before 1st Ring
Tx FSK with Line reversal before 1st Ring
Tx DTMF with Line reversal before 1st Ring
FSK cid with time message
Single type FSK CID
Show Cid Option
29
G03 VoIP TA
User Manual
Command
?
-ring
-r
-w
-a
(null)
Description
Show '
slic'Option
Issue Ring signal
read slic addr
write slic addr
read all slic reg
Show slic register
30