Documente Academic
Documente Profesional
Documente Cultură
HHO GENERATOR
Produced by:
Page
Function: Used as a hybrid (supplements) for land vehicles, marine and electric
generator (Genset)
Website : www.jokoenergy.com
E-mail-1: hho@jokoenergy.com
E-mail-2 : jokopriyono@jokoenergy.com
(i)
INSTALLATION INSTRUCTIONS
Page
MOTTO:
Better assume that everything has not been done, rather than
assuming that everything already done.
Chapter.I
(ii)
TABLE OF CONTENTS
page:
Page
A. Introduction.................................................................................................................3
Chapter. I
A. INTRODUCTION
Page
Concern that should arise from our own self for others to follow. One is using
water as fuel supplement (hybrid) for machinery or vehicles that we use
everyday.
Energy utilization has been more than 200 years old. Around the year
1805 Isaac de Rivaz managed to make a car with water fuel, although not
yet perfect but it is considered the first person generates hydrogen gas by
electrolysis of water because when the fuel (fossil) has not been found.
One of the more perfect is the inventor Stanley Meyer of Ohio, the United
States in 1995 with a modified VW car can go a distance of approximately
160 KM only with 3 liters of water, which eventually killed by poison in 1998.
Water is the source of life, no matter how much water we drink or use for
other purposes we will never run out. Why?
Because the circulation of water is only changed form, from liquid to solid or
gas that is eventually returned to the water again.
Another case of petroleum which is considered as an energy source, the
longer it will get out because the content is stored in the earth is limited. And
the exploitation and use of petroleum is also the fact that the negative
impact for life. Every day even every second exhaust fumes released tons of
toxic gases, such as: Carbon Monoxide, Nitrogen Monoxide, etc.. which can
cause various diseases such as respiratory tract infections, hypertension
and others until the air heats up the day that could cause CLIMATE
CHANGE.
What is predicted by the scientists on Global Warming is already starting
to happen.
Based on satellite data from NASA in December 2007 predicted that nearly
all the lumps will melt icebergs from the Arctic in late summer of 2012, if this
is not addressed soon jointly (global), most likely with the loss of all iceberg
which has been able to reflect sunlight back into space then no longer hold
the heat shield, so that the air temperature at Earth's surface will increase.
The occurrence of a significant increase in temperature causes the
warming of sea water which can produce a variety of toxic gases, can
certainly be imagined if the air we breathe every time it is not healthy
anymore, plus the increasing wave of tide gauges are happening
everywhere, especially in areas beach surface is lower due to increased
volumes of sea water.
Why does not anyone care?
Almost all the water fuel inventor, if you do not want to buy the copyright
is always a tragic experience, it is only by way of disseminating information
alone it can be avoided, so that everyone who read and know the secret can
contribute using it.
Page
Chapter.II
A. MATERIAL PRODUCT
Reaktor
Body & Reservoir
Gasket
B. PRODUCT TYPES
B1. Products for the vehicle:
1. Model: JE 500
Price = USD 334
Product Specifications:
Dimensions:
L 16 cm x W 16 cm x H 18 cm
Gas Output: 30 Lph (liters per hour)
Water Capacity: 650 ml
Voltage: 12 Volt DC
Electric current: 6-10 Ampere (max.12A)
Vehicle: gasoline Cars
Engine capacity: 1000cc-1800cc
2. Model: JE 600 CT
Page
3. Model: JE 850 CT
Price = USD 556
Product Specifications:
Dimensions:
L 20 cm x W 19.5 cm x H 23cm
Gas Output: 50 Lph 60 Lph
Water Capacity: 1250 ml
Voltage: 12 Volt DC
Electric current: 12 - 15 Ampere (max. 18A)
Vehicles: Car, Truck , Boat Fisherman
Electric Generator (Genset): < 15 KVA
Engine capacity: 2500cc-3800cc
4. Model: JE 1200
Price = USD 599
Product Specifications:
Dimensions:
L 21 cm x W 19.5 cm x H 23cm
Gas Output: 60 Lph - 72 Lph
Water Capacity: 1250 ml
Voltage: 24 Volt DC
Electric current: 8 - 10 Ampere (max. 12A)
Vehicles: Forklift, Truck, Bus, Boat Fisherman
Electric Generator (Genset): < 30 KVA
Engine capacity: >3800cc
Page
Page
Description:
Model : JE 850 CT (dual voltage = 12V dan 24V)
1. Connection cable socket on the reactor model: JE 850 CT (12 Volt)
The positive pole (+) = stainless steel plate 8th (middle position).
Negative pole (-) = stainless steel plate to the 2nd and 14th
combined.
At the time the vehicle is run for hours the temperature will rise
between 50 and 70 degrees Celsius and Ampere will rise about 2 A.
2.
Move the socket plate number 2 to number 1, and if it's still too high, you
can still move the jack plate number 14 to number 15.
Or get rid of all the water present in the reservoir and fill again with pure
water without catalysts (destilled water).
Page
1.
Page
Page
10
C. PRODUCT DESIGN
__oOo__
D. ACCESSORIES PRODUCTS
Each 1 unit HHO Generator comes with:
Page
11
PWM (PulseWidthModulation):
Accumulator:
Function as:
1). Container water (safety-1) if the water filling the
reservoir too full then the water will be carried out
with HHO gas into the accumulator tube.
2). Supplying water to the reservoir when the engine
is automatically switched off because of the void of
air (vacuum) in the reservoir.
Page
12
Bubbler-1:
Bubbler-2:
Pure water is filled up half of the works to prevent
the fire behind (back fire) and filter HHO gas is
mixed with water vapor from a chemical solution
(safety-3).
Page
13
Faucet (Valve):
Fitting T:
Used as a connection if the HHO gas is
injected into the intake manifold through a
vacuum hose (suction hose)
Cable ties:
Page
14
Chapter. III
PREPARATION
Page
15
1. Distilled Water :
Fig.1
3. Test the purity of water with incandescent bulbs (bohlamp):
Page
16
Fig.2
Fig.3
In Fig.2 visible light is not on because the water is pure distilled
in glass, whereas in Fig. 3 in fact quite the contrary, it could be
ignited by the water in the glass is not pure. And the intensity of
the light to follow the many substances that exist in the water.
Chapter. IV
INSTALLATION IN VEHICLE
Page
17
A. Preparation of installation:
Add the water it again until the water level with high
stainless steel plate in the reactor.
Page
18
1. Open the back of the carpet in the trunk and find the hole
light cable channels, if there is no search in addition to
the right or left wall and looking down toward the hole
channel.
2. Put the right side next to elektroliser unit or near the hole
on the left side light cable channels that have been
found.
3. Tie elektroliser unit to floor carpet by making 8 pieces
small hole in the carpet on the position of the foot just
below the hole elektroliser that has been provided to
include cable ties and rope trick got really strong
position is not easily knocked over or the best use of
license plate to the elbow that dibaud on the drill floor by
the floor of the trunk.
Page
19
Fig.4
Page
20
Page
13. Cut the hose at the position between the first and
second bubbler about 10 cm from the output bubbler-1
to install T fitting and check valve.
14. If the HHO gas will be injected into the air filter box:
Attach the hose from the output bubbler-2 into the air
filter box by making a hole size of 12 mm at its filter box
and attach elbow / knee that has been provided by way
of playing in order to form drat so no need in glue.
21
7. Prepare the hose and then pipe the length of the cable
from the engine towards the rear of the car through the
pit through the floor that are common to the rubber
covered holes, if not available then make a hole in the
drill itself by using the drill size of 12 mm
8. Continue to put the hose on the elbow located at the top
of the the accumulator tube.
9. Cut the hose is approximately 10 cm from the elbow
holes and attach the output Accumulator tube fitting T
and its check valve (check valve output position that
stuck to the hose), note the following:
10. Continue by installing the bubbler to 1 and 2 in the
engine room standing in an upright position.
11. Connect the hose from the back to input a bubbler-1.
12. And proceed to install the hose from the output of the
first bubbler to bubbler second input section.
Page
22
Page
23
24
Page
Page
25
Page
34. Connect the cable from the PWM (output / right) directly
to the pole (-) black terminal on HHO reactor.
35. Connect the small cable (red or blue) of the PWM
middle to the poles (+) terminal of red in HHO reactor.
36. If everything is installed then re-examine whether the
installation is correct or not.
26
27
Page
28
Page
Page
29
Page
30
F. WARNING HARD
Page
31
Chapter. V
TREATMENT:
Page
32
1. Catalysts:
Catalysts are indispensable in the process of electrolysis of
water because without the catalyst the HHO gas produced very
little could not produce gas even at all if the content in the water
is really pure that there is no benefit.
Best catalysts are widely used by the examiners
(eksperimentor) water fuel global level are: KOH (potassium
hydroxide) and NaOH (sodium hydroxide).
Electrolyser "Joko Energy" using KOH catalyst for more
effective levels of 20% KOH than NaOH. And the use of NaOH
at high levels also produce a lot of sludge solids so that its
water dirty quickly.
KOH is usually only sold in stores that sell chemicals only, while
NaOH are sold in stores are the public buildings known as
caustic soda.
The use of catalysts is quite simply once, as well as the use
of chemicals on a new battery, which then just add distilled
water / pure water alone for about 2-3 months or depending on
vehicle usage.
Page
33
Page
34
__oOo__
Chapter. VI
ACCESSORIES
Page
35
36
Page
B. OXYGEN ENHANCER :
O2 Enhancer works to make the ratio to 18: 1
with protection:
a very large input impedance 2 MOhm so it will not
damage the sensor (sensor can be damaged if the
current work going short to ground).
maximum output voltage of 0.88 volts so it will not
damage the ECU.
Page
37
C. MAP Sensor :
Work to determine the size of
the ratio of air and fuel when the
engine is cold, or cold air, and
during acceleration (change in
velocity). Working with an output
of 1.5 to 3.6 volts with a little
depending on the valve open
when stepped on the gas pedal.
MAP Sensor Cables have 3 pieces, each one is +5 volts,
ground, and signal out (1.5 up to 3.6 volts)
D. MAP Enhancer :
MAP Enhancer works to reduce fuel consumption at the time
as above with protection:
Input Impedance 50 kOhm so not to damage the MAP
sensor.
Output voltage max 4.7 volts so it does not damage the
ECU.
MAP Enhancer is equipped with IC and a relay that can
regulate DC voltage via a potentiometer subtly so the benefits
would be more superior and safer than those who still use a
simple circuit consisting only of potensio and resistors only.
Page
38
Toyota Avanza
1.3 & 1.5
Signal =1,5V3,6V
Red wire white stripe
Daihatsu
Xenia 1.3 &
1.5
Daihatsu Gran
Max
Signal =1,5V3,6V
Red wire white stripe
Signal =1,5V3,6V
Red wire white stripe
O2 Sensor
Signal = 0,4V - 0,8V
Cables blue, gray resumed after
socket
Signal = 0,4V - 0,8V
Cables blue, gray resumed after
socket
Signal = 0,4V - 0,8V
Black wire after the connector
39
CARS
Page
No.
Page
40
41
Page
Page
42
Chapter. VII
DEFAULT ON VEHICLE ENGINE
Page
43
1. Carburettor
Page
44
Page
45
If the Reset ECU has been done but the car is still more
extravagant than before using HHO, it means that your car
does not have the facilities RESET ECU, what to do?
Use the guidelines for 3 amperes per 1000 cc, what is it?
This means that the use of HHO adjusted according to engine
capacity, for example:
3. DIESEL
Page
46
This is the kind of machine that fits directly with HHO hybrid
because it does not require spark ignition timing, so that the
presence of HHO as a supplement even if the machine is not
setup has immediate benefits, especially if the settings in Bosch
Pump held to reduce fuel consumption or can manipulate the
ECU will get savings from 50% to 80%.
As we have seen in diesel engines use compression
systems in combustion of the fuel, then the presence of HHO
supplements significantly reduce the engine as before the fuel
reached a very high level of pressure the mixture of fuel, air and
HHO has exploded first, this proved diesel cars in time will
make the machine easy on the starter does not even require a
longer heating.
Chapter. VIII
User Experience
(Testimonial)
The use of water fuel technology plant that produces
Hydrogen and Oxygen gases and mixed in the combustion
process in the engine called Hybrid Air. This fuel typically use
the system HOD (Hydrogen On Demand) which produces
hydrogen gas as needed and used immediately without storage
first.
With the mixing of these machines have an extra vehicle
(double power) derived from hydrogen gas, so it's no surprise
that the new gas pedal just a little trampled, the vehicle is
already in motion as there is a push from behind. The Oxygen
serves as a complement combustion in the engine, so even if
the vehicle or car condition has issued a dense smoke will look
cleaner as no fumes even if the fuel Solar HHO gas sufficient.
Two things that causes the efficiency (not wasteful of fuel
efficient), environmentally friendly, clean engine of the crust
Carbon and do not contaminate the engine oil. And the event
was able to restore the performance of both vehicles on a new
car and the old ones, even for the old car will feel completely
like a new car, both the efficiency and strength.
Here is an example of the recognition of the users HHO
Generator "Joko Energy":
Page
47
* "My car Toyota New Innova Diesel for the year 2012, after
the pair HHO Generator result: more efficient than the previous
1 liter = 12 km to 1 liter = 18 Km and just use regular diesel
Pertamina, no need to use DEX or Shell again, more exhaust
gas comfortable and odor although the car is started in the
room, sound engine now smoother and feels more powerful "
- From: Mr. Aryanto, ST; Pekalipan, Cirebon, West Java.
Page
48
a. In the city:
1 liter of gasoline = 13 km (with AC)
1 liter of gasoline = 15 km (without AC)
b. Out of town:
1 liter of gasoline = 18 km (with AC)
1 liter of gasoline = 19.3 km (without AC)
- From: Mr. Mahmuddin Noor, NST
Housing MANDALA Medan, North Sumatra.
Page
49
Page
50
Chapter. IX
Tests on Ships
How lucky we got a chance to test electrolyser (HHO
Generator) on board, because there are good-hearted owner of
the vessel. He is the father of Ustad Mutedi who resides on the
island of Java, which is a good thing one of the clusters of the
many islands in the Thousand Islands. The ship is KM. Bunga
Mawar Express that uses machine FUSO type: 6D14
passenger capacity has reached 150 people with the ships
Master Mr. Jawadi.
Page
51
Chapter. X
HOW TO ORDER
For booking tool, please contact:
Joko Energy Indonesia
Workshop
Jln. Pondok Randu No.78,Duri Kosambi,
Cengkareng, West Jakarta.
Phone / SMS : (+6221) 36767898,
+6287888378555, +6285777999157
+628129989606,
E-mail: jokopriyono@jokoenergy.com
E-mail: hho@jokoenergy.com
Page
52
___oOo___
Chapter. XI
PROFILE Joko Energy
Page
53
54
Page
55
Page