Documente Academic
Documente Profesional
Documente Cultură
SESC99007
Revision A
Notice:
n All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
respective owners. EPSON disclaims any and all rights in those marks.
Revision A
PRECAUTIONS
Precautionary notations throughout the text are categorized relative to 1)Personal injury and 2) damage to equipment.
DANGER
Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by
DANGER Headings.
WARNING
The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.
DANGER
1. ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR REPAIR
PROCEDURES.
2. NOWORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL ELECTRONICS
TECHNICIANS IN THEIR LINE OF WORK.
3. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL INSTRUCTED TO DO
SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER SUPPLY AND OTHER ELECTRONIC
COMPONENTS.
WARNING
1. REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.
2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING PLATE. IF THE
EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.
3. ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR REPLACING PRINTED
CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.
4. IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC WRIST
STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.
5. REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECOND-SOURCE ICs OR
OTHER NONAPPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.
Revision A
PREFACE
This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of EPSON Expression 1600/1600 Pro. The instructions and
procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. The chapters are organized as follows:
CHAPTER 1.
PRODUCT DESCRIPTIONS
CHAPTER 2.
OPERATING PRINCIPLES
CHAPTER 3.
TROUBLESHOOTING
CHAPTER 4.
CHAPTER 5.
ADJUSTMENTS
CHAPTER 6.
MAINTENANCE
APPENDIX
Revision A
Revision Status
Revision
Issued Date
Description
First Release
Revision A
Contents
PRODUCT DESCRIPTIONS
Features ......................................................................................................... 8
Specifications ................................................................................................. 8
Interfaces...................................................................................................... 10
SCSI Interface ......................................................................................... 10
USB Interface .......................................................................................... 11
IEEE1394 Serial Bus Interface................................................................ 11
Buttons and Lamps....................................................................................... 12
Buttons .................................................................................................... 12
Indicators ................................................................................................. 13
Physical Specifications ............................................................................ 13
Scanning Area......................................................................................... 14
Control Codes and Commands .................................................................... 15
Errors............................................................................................................ 16
OPERATING PRINCIPLES
Mechanism Operating Principles.................................................................. 18
Fixed Type Two Focuses Mechanism..................................................... 18
Control Circuit Operation .............................................................................. 19
TROUBLESHOOTING
Overview....................................................................................................... 24
ADJUSTMENT
Overview ...................................................................................................... 36
MAINTENANCE
Overview ...................................................................................................... 38
APPENDIX
Overview ...................................................................................................... 40
Interconnection of the Major Components .............................................. 40
Connector Summary ............................................................................... 41
B109 MAIN Board Connector Pin Assignment........................................ 42
Component Layout ....................................................................................... 47
Exploded Diagrams and Parts List ............................................................... 48
Exploded Diagrams ................................................................................. 48
Parts List ................................................................................................. 51
Circuit Diagrams ........................................................................................... 52
Overview....................................................................................................... 28
Tools........................................................................................................ 28
Disassembly Procedures .............................................................................. 29
LED Board Removal................................................................................ 29
Operate Switch Board Removal .............................................................. 29
CHAPTER
PRODUCT DESCRIPTIONS
Revision A
1.1 Features
1.2 Specifications
This specifications are applied to the EPSON Color Image Scanner Expression 1600/1600
Pro.
GENERAL SPECIFICATIONS
o Product type:
Flatbed Color Image Scanner
o Sub-scanning method:
Movement of the Scanner-Head
o Photoelectric device:
Alternative 6-line CCD (40800 pixel)
o Maximum document size: 8.5 x 11.7 inches (216 x 297 mm)
o Maximum picture element: 13,600(main) x 18,720(sub) pixels (1600dpi)
o Scanning Resolution:
The best Color Image Scanner for both graphics and office usage.
Maximum document size:
Scanning speed:
1600dpi(main) x 3200dpisub)
Pixel depth:
Max. OD Value:
3.3D
Focus control:
2position
o
o
o
o
o
o
o
o
Main:
Sub:
Output resolution:
50 ~ 4800dpi (1dpi step)
Pixel depth:
In 12-bit / pixel, Out 1-12bit/pixel
Color separation method:
By the color filter of CCD
Zoom:
50 ~ 200% (1% step)
Scanning speed (1600dpi,Draft Mode):
Start bottom
Color:
9.2ms/line
Monochrome:
3.1ms/line
o
o
Command level:
ESC/I-B8, FS
Image processing functions:
Gamma correction:
CRT (A, B)
Printer (A, B, C)
User Defined Table
Color correction:
FS
Option
ADF (Same as the GT-9600s)
TPU (Same as the GT-9600s, but Film holder is added)
IEEE 1394 Board
PRODUCT DESCRIPTIONS
Features
Brightness:
7 levels
Line art:
Fixed threshold
TET
Halftone:
Area separation:
AAS
EMC:
CE marking:
Interface:
SCSI (50-contact high-density connector, standard)
USB (Type-B Receptacle Connector, standard)
Revision A
Light source:
ELECTRICAL SPECIFICATIONS
o Rate voltage:
Universal Power Supply
AC100-120V
AC220-240V
o Input voltage:
AC100-120V10%
AC220-240V10%
o Rated current:
0.8 A (Input AC110V)
0.4 A (Input AC220V)
o Rated frequency range:
50-60Hz
o Input frequency range:
49.5-60.5Hz
o Power consumption:
Approx.30 W (without optionan unit)
Approx.50 W (without optionan unit)
Approx.10 W (without optionan unit)
o Insulation resistance:
10MW at 500VDC
(between AC line and chassis)
o Dielectric strength:
AC1.2kV, 1min
(between AC line and chassis)
PRODUCT DESCRIPTIONS
EN55022 Class B
EN61000-3-2
EN61000-3-3
EN 50082-1
IEC 801-2
IEC 801-3
IEC 801-4
EPA:
Revision A
1.3 Interfaces
OPERATING CONDITIONS
Dust:
Ordinary office or home conditions. Extreme dust
This section includes the specifications for the interfaces equipped with this scanner.
should be avoided.
Illumination:
Operation under direct sunlight or near strong light
ADF/TPU Connector
DOCUMENT
Reflective ty pe:
Documents which has a smooth surface such as a
printing and photograph.
IEEE1394 Interface
USB
SCSI Interface
(Optional)
PRODUCT DESCRIPTIONS
Interfaces
10
Revision A
n Device:
Class:Vender specific
Sub class:Vender specific
Protocol:Vender specific
Maximum packet size for end point 0:0x04B8
Product ID:0x0107
Number of formation:1
n Configuration:
Alternate setting value:None
Number of end points:2
Class:Vender specific
Sub class:Vender specific
Protocol:Vender specific
n End point 1:Bulk IN transmission
Maximum packet size: 64 byte
n End point 2:Bulk OUT transmission
Maximum packet size: 64 byte
n String descriptor:Manufacturer: EPSON
Product name: Expression 1600/1600 Pro
o Electrical specifications:
Compliant with the high speed mode
(12Mbps)
o Connector:
B receptacle (1)
o Pin arrangement, Pin assignment:
Table 1-1. USB Pin Assignment
2
3
1
4
PRODUCT DESCRIPTIONS
Pin No.
Signal
VCC
- Data
- Data
GND
Interfaces
11
Revision A
1.4.1 Buttons
The buttons equipped with this scanner and their functions are as shown below:
LED Lamps
Start Button
Operate switch
Start bottom
Functions
Operate Switch
SCSI ID Switch
Terminator Switch
PRODUCT DESCRIPTIONS
12
Revision A
1.4.2 Indicators
The table below lists the indicator lamps equipped with this scanner. (See Figure 1-1 for the
location.)
External view
ERROR
(Red LED)
mm
562
332 m
m
The scanner shows several error conditions by turning on/off each lamp as shown in the
table below:
Lights up
Command Error
Off
Blinks
Interface Error
Blinks
Blinks
Fatal Error
Off
Off
Option Error
PRODUCT DESCRIPTIONS
m
m
33
1
o
o
Dimensions:
Weight:
13
Revision A
216 mm
1.0 - 1.5 mm
mm
5.0
-6
.1
mm
79
2
Front
PRODUCT DESCRIPTIONS
14
Revision A
Classification
The control codes and commands of the scanner are as listed in the following table:
Image disposition
Classification
Command
Correction
Name
Code
ID request
ESC I
status request
ESC F
ESC f
ESC S
start scanning
ESC G
ESC !
extended ID request
FS I
FS F
FS S
FS G
ESC D i
set resolution
ESC R n1 n2
set zooming
ESC H i1 i2
ESC A n1 n2 n3 n4
set color
ESC C i
set mirroring
ESC K i
FS W
set brightness
ESC L i
ESC Z i
ESC z i d[256]
ESC Q i
PRODUCT DESCRIPTIONS
Control
Name
Code
ESC B i
ESC s i
ESC b i j d[j^2]
ESC M i
ESC m d[9]
set threshold
ESC t i
ESC g i
initialize
ESC @
ESC d i
option control
ESC e i
ESC N i
ESC p i
ESC q
eject paper
FF
normal response
ACK
abnormal response
NACK
stop scanning
CAN
header
STX
15
Revision A
1.6 Errors
[Indicator]
COMMAND ERROR
[Remedy]
[Cause]
[Disposition] The scanner sends NACK and waits for the next command. When the scanner
receives a wrong command or parameter, it disregards a value and
maintains the former value.
[Indicator]
[Remedy]
The error condition is cleared when the scanner receives a correct command.
INTERFACE ERROR
[Cause]
[Remedy]
[Remedy]
FATAL ERROR
[Cause]
PRODUCT DESCRIPTIONS
Errors
16
CHAPTER
OPERATING PRINCIPLES
Revision A
Document Glass
Focus Glass
During normal scanning that uses the document glass, the focus glass is held up to enable
the incident light to focus on the document glass. When TPU is selected on the users
application, however, the focus glass lowers 90, driven by the specified motor, to be set
between the first glass and second glass. This operation shifts the light path to raise the
focusing point 2.5 mm from the document glass, which allows the scanner to focus on the
TPUs film scanning surface.
Figure 2-1 illustrates the focusing mechanism of the Expression 1600/1600 Pro.
Lamp
1st Mirror
TPU Holder
2nd Mirror
CCD
4th Mirror
3rd Mirror
m5m
.2
Lens
OPERATING PRINCIPLES
18
Revision A
The control circuit of the scanner is composed of the following electrical circuit boards:
n
n
n
n
n
n
n
n
B109 ISN Board (CCD sensor control board / Attached on the CR)
B109 MAIN Board (main control circuit board)
B109 PSH Board (power supply control board)
B109 SUB Board
B109 SUB-B Board (Push switch and LED control circuit board)
B109 SUB-C Board (Operate switch board)
B109 SUB-D Board (Relay board)
B80834* I/F Board (IEEE1394 I/F control board)
Location
CPU (HD6412350F20)
IC1
IC2
IC3
T-Rex (E02A31EA)
IC5
See Figure 2-2 for the block diagram of these control circuits.
The following tables show the major elements of each circuit board.
Location
Description
IC1
AFE (VSP3010Y)
IC2
OPERATING PRINCIPLES
Description
19
Revision A
Name
Location
IC6/7
CR motor driver
(A3957SLBTR)
SCSI controller
(SPC7211F0B)
IC8/9
IC10/11
IC12
Description
Work area of the firmware.
32K*8Bit*2
28-pin 300mil SOJ/1.27-mm pitch
Power supply voltage: 5.0 V 10%
Maximum consumption current: 1.5W
Maximum access time: 15ns
Data area for the T-Rex image processing and
output buffer for the T-Rex.
Operates at 95MHz.
2M*8Bit*2
54-pin TSOP/0.5-mm pitch
Power supply voltage: 3.3 V 0.3V
Maximum consumption current: 1.0W
Maximum access time: 6ns
Scanner carriage motor driver
24-pin SOP/1.27-mm pitch
Power supply voltage:
Logic: 5.0 V 10%
Motor: 24V (5V - 50V)
Destination
Logic line
Carriage HP sensor
LED power
CCD drive/amplifier
Carriage motor drive
Lamp drive
Standby Current
Rated Current
5 0.2 V
0.8A
1.5A
15 0.8 V (12V)
0.2A
0.3A
24 2.4 V
0.05A
1.5A
o
o
o
o
o
SCSI terminator
(BH9596FP-YE2)
IC13
USB controller
(E02A29BB)
IC14
OPERATING PRINCIPLES
DC Output
Voltage
CPU (IC8):
HD6412350F20
20
o
o
MN864400
TSB41LV03
OPERATING PRINCIPLES
Revision A
21
Revision A
B109 SUB
S
W
B
8
13 H 083
8
94 S 4
*I
Co
/F
nt
ro
le
r
P
R
O
M
S
R
A
M
(H
D
6
4
1
2
3
5
0
F
2
0
( I
1 C
2
8 2
K
*
8
B
it
)
( I
3 C
2 3
K
*
8
B
it
)
H.
P.
ID
S
W
C
PU
LE Pu
D sh
SW
J
P
2
,1
I
C
1
Da
ta
Bu
s
De SC
vic SI
e
De SC
vic SI
e
(
E
0
2
A
2
9
B
A
)
0
2
A
3
1
E
A
I
C
1
4
Te IC
rm 13
ina
tor
(
S
P
C
7
2
1
1
)
S
C
S
I
C I
C
o
1
n 2
t
r
o
ll
e
r
(
A
3
9
5
7
S
L
B
T
R
)
Da
ta
Bu
s
A
dd
re
ss
B
su
(E
U
S
B
C
o
n
t
r
o
ll
e
r
+2
4V
De 13
vic 94
e
De US
vic B
e
La
mp
Un
it
Gl M
ass oto
rF
or
(
3
2
K
*
8
B
i
t
*
2
)
S
R
A
M
T
-R
ex
I
C
6
/
7
+5
V
,+
15
V
S
u
p
p
l
y
P
o
w
e
r
M
o
t
o
r
D
r
i
v
e
I
C
1
0
/
1
1
B
10
9S
U
BB
B
10
9P
SH
M CR
oto
r
I
C
5
(
2
M S
D
*
8 R
b A
i
t M
*
2
)
I
C
8
/
9
AF
E(
VS
P3
01
0)
CC
D
B
10
99I
ISSN
N
OPERATING PRINCIPLES
22
CHAPTER
TROUBLESHOOTING
Revision A
3.1 Overview
Since the scanner mechanism and the electrical circuits of this scanner are similar to the
GT-9500s, you can solve most problems by referring to the GT-9500 Service Manual.
Therefore, this chapter only provides causes and remedies for fatal errors.
Name of
Sensor
HP Sensor
In order to find out any wrong status of the motor or sensor by measuring, the signal
specifications of CR Moto and HP Sensor are shown as follows.
Table 3-1. Resistance of CR Motor
Name of Motor
CR Motor
Resistance
Test Point
Signal Level
Status
CN3 / Pin 1
High (5V)
The following tables separately provides the error conditions and remedies for the scanner,
ADF, and TPU.
Occurs when:
Carriage is reset.
Image reading is
completed.
TROUBLESHOOTING
Conditions
Causes
Overview
Remedies
24
Revision A
Occurs when:
Scanner is being
initialized.
TROUBLESHOOTING
Conditions
Causes
Paper is jamming.
Registration sensor / Paper eject
sensor is defective or its cable is not
connected properly.
Switch lever is damaged.
Motor cable is not connected
properly.
Top cover of the ADF is open.
Small cover open sensor is off.
Small cover sensor is defective.
ADF is open.
Cover open sensor is off.
Cover open sensor is defective.
Registration sensor does not turn on Paper is jamming.
or off.
Registration sensor / Paper eject
Paper eject sensor does not turn on
sensor is defective.
or off.
Switch lever is damaged.
Overview
Remedies
25
Revision A
Occurs when:
Conditions
Causes
HP sensor is defective.
Lamp unit is still secured with the
fixing screw.
TPU lamp has blown out.
check is not completed after 30
Lamp check at power on Lamp
Foreign matter is lodged on the
seconds.
smaller glass of the scanner.
Maximum outputs of all sensors are TPU lamp is defective.
lower than 20LSB.
Life end of the TPU lamp
CCDs accumulated time is 100
Ferris matter is lodged on the small
microseconds or less.
Automatic light level
glass.
correction
CCDs accumulated time is 20
milliseconds or more.
Automatic light level correction is
not completed after 30 seconds.
Cover open sensor is off.
TPU is open.
Image reading begins.
Cover open sensor is defective or its
cable is not connected properly.
HP
sensor in the scanner is
Carriage does not return to the home
Image reading is over.
defective.
position.
TROUBLESHOOTING
HP is not detected.
Remedies
Overview
26
CHAPTER
Revision A
4.1.1 Tools
4.1 Overview
This chapter explains how to disassemble the major units and components of the Expression
1600/1600 Pro. Since the scanners components and units are basically the same as for the
GT-9500 and GT-9600, items that are specific to this scanner are only provided here.
Unless otherwise specified, assembly can be performed by reversing the disassembly
procedures.
W A R N IN G
C A U T IO N
The tools used to service on this scanner are as listed in the table below:
Description
Availability
Code
Commercial
B743800200
Tweezers
Commercial
B641000100
Commercial
Pliers
Commercial
B740400100
Overview
28
Revision A
1.
2.
3.
1.
4.
2.
5.
Disconnect the harness from CN1, remove the one screw (CBS, 3x12), and then
remove the Operate Switch Board from HOUSING, L OWER.
3.2.1.)
3.
Disconnect the harness from CN1 and remove the one screw (CBS, 3x12). Then
remove the L ED Board from HOUSING, LOWER. (See Figure 4-1.)
CN1
CN1
Disassembly Procedures
29
Revision A
HOLDER, FOCUS
COVER, LAMP
LAMP, ASSY.
C A U T IO N
n
n
Disassembly Procedures
30
Revision A
CB Screw (3x6)
CB Screw (3X6)
CN1
CN3
4. Remove the two screws (CB, 2x3) securing MOTOR ASSEMBLY, FOCUS
Assembly to FRAME, FOCUS, and remove MOTOR ASSEMBLY, FOCUS.
CBS Screws (3X12)
Disassembly Procedures
31
Revision A
CN3
CN1
CN11
Disassembly Procedures
32
Revision A
5. Remove the three screws (CBS, 3x6) and remove GROUNDING PLATE.
6. Disconnect the harnesses from CN3, CN4, CN5, and CN6 on the B109 MAIN
Board, and then remove the B109 MAIN Board from HOUSING, LOWER.
(See Figure 4-11.)
CBS Screws (3X6)
GROUNDING PLATE
CN2
CN3
CN1
C
N
6
C
C
N
N
5 4
CB Screw (3x3)
Disassembly Procedures
33
Revision A
3. Disconnect the harness from CN7 on the B109 MAIN Board. (See Figure 4-13.)
Optional I/F
Disassembly Procedures
34
CHAPTER
ADJUSTMENT
Revision A
5.1 Overview
This scanner does not require any adjustment for specified services such as disassembling
and assembling the scanner, including parts replacement.
ADJUSTMENT
Overview
36
CHAPTER
MAINTENANCE
Revision A
6.1 Overview
For information on how to maitain the EPSON Expression 1600/1600 Pro, please refer to
the GT-9500 Service Manual.
MAINTENANCE
Overview
38
CHAPTER
APPENDIX
Revision A
7.1 Overview
This chapter provides information necessary for servicing.
SCSI
Device
SCSI
Device
USB
Device
CN8
CN9
CN10
1
NC
B109 SUB-D
Board
AC IN
CN1
2
NC
CN7
3N
C
B109 MAIN
6N
C
CN1
B109
B109 PSH
PSH
Board
Board
HP Sensor
CN3
CN4
CN2
CN5
Inverter
Circuit Board
B109 SUB-C
Board
B109 ISN
Board
Lamp
FOCUS GLASS
CR MOTOR
CR
MOTOR
B109 SUB-B
Board
APPENDIX
Overview
40
Revision A
Board
CN No.
APPENDIX
Refer to:
CN1
Table 7-2
CN2
Table 7-3
CN3
Table 7-4
CN4
Table 7-5
Table 7-6
Table 7-7
CN7
Table 7-9
CN8, 9
Table 7-10
CN10
Table 7-8
CN11
Table 7-11
CN1
CN2
Table 7-7
CN3
B109 PSH
Board
Function
Overview
41
Revision A
APPENDIX
Pin
Signal Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
AGND
+12V
+12V
AGND
DGND
DGND
+5V
+5V
DGND
SHB
SHG
SHR
SNCK2
CSL0
LCMP
SNCK1X
SNCK1
TG
CSL1
ADCK
I/O
O
O
O
O
O
O
O
O
O
O
O
Function
Analog GND
Power supply (+12V)
Power supply (+12V)
Analog GND
Digital GND
Digital GND
Power supply (+5V)
Power supply (+5V)
Digital GND
CCD: Output shutter for Blue (ICG1)
CCD: Output shutter for Green (ICG2)
CCD: Output shutter for Red (ICG3)
CCD: Reset (RS)
CCD: Clamp (CP)
AFE: Line clamp (START, CLP)
CCD: Clock 2 (F1B)
CCD: Clock 1 (F1A, /F2A)
CCD: Shift pulse (SH)
CCD: Clock 3 (/F2B)
AFE: Clock (ADCK)
Pin
Signal Name
I/O
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
SNCK4
SNCK3
WR
SD
SCK
DGND
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
DGND
O
O
O
O
O
Overview
I
I
I
I
I
I
I
I
I
I
I
I
Function
42
Revision A
Pin
Signal Name
COM
COM
AN
I/O
Pin
Signal Name
I/O
HP
GND
GND
+5V
BN
+24V
+24V
+24V
10
LMPCNT
11
GND
GND
12
GND
GND
13
GND
GND
Function
Function
Pin
Signal Name
I/O
Function
BX
AX
APPENDIX
Overview
Pin
Signal Name
I/O
Function
+5V
LEDR
LEDG
P_SW
43
Revision A
Pin
Signal Name
+24V
I/O
Function
Pin
Signal Name
+24V
+24V
+24V
GND
GND
GND
GND
GND
GND
+5V
+5V
GND
GND
+5V
OP5
I/O
+15V
OP_SEL
GND
GND
OP4
GND
GND
SLOAD
10
GND
GND
10
OP3
11
GND
GND
11
SCK
12
GND
GND
12
OP2
13
SDATA
14
OP1
15
GND
16
ID_8
17
ID_1
18
ID_4
19
ID_2
20
T_SW
Pin
Signal Name
I/O
Function
Vcc
-Data
I/O
USB -Data
+Data
I/O
GND
APPENDIX
I/O
Function
GND
GND
Overview
44
Revision A
APPENDIX
Pin
Signal Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
I/O
Function
Pin
Signal Name
I/O
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DBP
GND
GND
GND
TRMPW
GND
GND
ATN
GND
BSY
ACK
RST
MSG
SEL
C/D
REQ
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Overview
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Function
SCSI data 0
SCSI data 1
SCSI data 2
SCSI data 3
SCSI data 4
SCSI data 5
SCSI data 6
SCSI data 7
SCSI data parity
GND
GND
GND
TERMINATOR POWER
GND
GND
SCSI ATN
GND
SCSI BSY
SCSI ACK
SCSI RST
SCSI MSG
SCSI SEL
SCSI C/D
SCSI REQ
SCSI I/O
45
Revision A
APPENDIX
Pin
Signal Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
GND
DM[0]
DM[2]
DM[4]
DM[6]
GND
DM[8]
DM[10]
DM[12]
DM[14]
GND
IMG
CS
WR
SYSRS
GND
D[0]
D[2]
D[4]
D[6]
GND
DREXT
RDREQ
+5V
+5V
I/O
O
O
O
O
O
O
O
O
O
O
O
O
I/O
I/O
I/O
I/O
I
O
Function
GND
Image Data 0
Image Data 2
Image Data 4
Image Data 6
GND
Image Data 8
Image Data 10
Image Data 12
Image Data 14
GND
Not used
Resister select
Resister write
Power on reset
GND
Resister data 0
Resister data 2
Resister data 4
Resister data 6
GND
DMA request
Ready (= L)
Power Supply (+5V)
Power Supply (+5V)
Pin
Signal Name
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
GND
DM[1]
DM[3]
DM[5]
DM[7]
GND
DM[9]
DM[11]
DM[13]
DM[15]
GND
WREXT
RD
ADR
NC
GND
D[1]
D[3]
D[5]
D[7]
GND
INTEXT
+24V
+5V
+5V
Overview
I/O
O
O
O
O
O
O
O
O
O
O
O
I/O
I/O
I/O
I/O
I
Function
GND
Image Data 1
Image Data 3
Image Data 5
Image Data 7
GND
Image Data 9
Image Data 11
Image Data 13
Image Data 15
GND
DMA write
Resister read
Resister address
Not connected
GND
Resister data 1
Resister data 3
Resister data 5
Resister data 7
GND
Interruption
Power Supply (+24V)
Power Supply (+5V)
Power Supply (+5V)
46
Revision A
APPENDIX
Component Layout
47
Revision A
135
134
129
135
176
151
181
143
129
139
107
149
B
E
104
124
176
151
181
136
171
176
176
181
181
178
107
181
116
141
181
420
470
137
163
177
117
175
109
430
165
131
176
106
108
181
165
144
181
108
105
131
181
176
120
138
164
111
119
175
178
100
121
118
130
101
114
114
112
115
112
115
A
110
145
APPENDIX
147
146
10143
48
Revision A
460
161
142
174
176
170
170
113
176
153
400
185
440
179
200
148
142
172
127
176
123
181
142
140
162
D
181
142
132
G
181
F
172
122
176
172
102
181
181
181
128
I
172
169
125
176
172
181
410
172
176
168
166
181
181
176
173
181
172
181
181
181
APPENDIX
176
181
181
167
181
181
181
300
176
181
181
No.2
Rev.01
10143
49
Revision A
450
519
APPENDIX
10143
50
Revision A
APPENDIX
Part No.
1049816
1049101
1050474
1049817
1042703
1029438
1029441
1052016
1029442
1052020
1051432
1007525
1008492
1009569
1012618
1017596
1022304
1022306
1050012
1042614
1025472
1025473
1049110
1049111
1029431
1042632
1049112
1049362
1029443
1050013
Part Name
HOUSING ASSY.,UPPER
HOUSING,LOWER
PLATE,ASSY.,BOTTOM
COVER ASSY.,DOCUMENT
GLASS ASSY.,LARGE
FRAME,FRONT
FRAME,REAR
FRAME,SIDE,L
SHEET,FRAME,SIDE
RAIL,CENTER
LOGO PLATE;B
TORSION SPRING,17100
PLAIN WASHER 3*0.5*8 F/ZN
SCREW,CONNECTOR,ADF
DAMPER,CR
SHAFT,DAMPER,CR;B
HOLDER,PULLEY,DRIVEN
SHAFT,PULLEY,DRIVEN
LEVER ASSY.,TENSION
PULLEY,DRIVE
TIMING BELT;B
ROLLER,TENSION
SHIELD PLATE,POWER SUPPLY
SHIELD PLATE,REAR
GROUNDING PLATE,FRONT
GROUNDING PLATE,POWER SUPPLY
GROUNDING PLATE,FFC
GROUNDING PLATE,SHIELD;B
SHEET,FRAME,REAR
FRAME ASSY.,MOTOR
Drawing No.
131
132
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
165
166
167
168
169
170
171
172
173
174
175
Part No.
1030479
1042634
1033384
1032131
1032407
2032842
2028613
1042613
1049361
1042599
1025491
1022255
1042629
1049107
1049105
1049106
1049108
1042615
1049118
1042624
1030684
1031846
1022274
1051576
1051577
1051578
1051579
B010102412
B010303311
B010350511
1051580
B045800115
B150300611
Part Name
SLEEVE,FRAME,REAR
GROUNDING PLATE,POWER SUPPLY;B
GROUNDING PLATE,FRAME
SHEET,FRAME,PROTECT
EXTENSION SPRING,600
DETECTOR,HP;E
MOTOR ASSY.,CR
TIMING BELT
GROUNDING PLATE,SHIELD
CLAMP,BELT
FOOT
GLASS,SMALL
LEVER,LOCK
OPTICAL PLATE
KEYTOP,POWER SWITCH
KEYTOP,START SWITCH
COVER,I/F,PLATE
PULLEY,DRIVEN
SHEET,SHIELD,MAIN;B
SHEET,FRAME,REAR;B
HEXAGON NUT,GROUND
DOUBLE SIDE TAPE,75X20
METAL FITTING COVER DOCUMENT
GROUNDING PLATE,SHIELD;D
GROUNDING PLATE,SHIELD;E
GROUNDING PLATE,SHIELD;F
GROUNDING PLATE,SHIELD;G
C.P.SCREW,2.5X8,F/NI
C.B.SCREW
C.B.SCREW
GROUNDING PLATE,SHIELD;H
C.B.(O) SCREW 4X8 F/ZG
RETAINING RING
51
APPENDIX
Part No.
B300204211
2025174
1049800
B010103212
B310204511
1049109
2032301
2032307
2032313
2032309
2032311
2032305
Y901300600
2032448
2032447
2032449
2032445
2032444
2032450
2032446
2028921
2032549
1030337
2032412
2032413
1042598
1042605
1029462
1029448
1022332
1042601
2025174
1049446
Revision A
Part Name
C.B.S. SCREW
FERRITE CORE
C.P.S-TITE(S-P4)SCREW,3X6,F/ZN
C.P.SCREW
C.B.B. SCREW
COVER,OPTION
BOARD ASSY., MAIN
BOARD ASSY., SUB
BOARD ASSY., SUB
BOARD ASSY., SUB
BOARD ASSY., SUB
BOARD ASSY., POWER SUPPLY
POWER CABLE
WIRE-HARNESS
WIRE-HARNESS
WIRE-HARNESS
WIRE-HARNESS
WIRE-HARNESS
WIRE-HARNESS
WIRE-HARNESS
I/F CABLE
CARRIAGE ASSY.
ROLLER,CARRIAGE;C
BOARD ASSY.,INVERTER
LAMP,ASSY.
COVER,LAMP
COVER,CR
COVER,MOUNT PLATE
MOUNT PLATE,MAIN
HOLDER ASSY.,ROLLER
CLAMP.FERRITE CORE
FERRITE CORE
COVER,REAR,CR
Drawing No.
512
513
514
515
516
517
518
519
520
Part No.
1000639
1042602
1044031
1043166
1044030
2032510
B010309411
2032524
B150350111
Part Name
SLIDER,CARRIAGE
BURSH,CR
BRUSH,CR;B
DOUBLE SIDE TAPE,8X17
BLOCK,HOLD,FFC
REUSE CLAMP,RLMC-05T V-0
C.B.SCREW,2X3,F/ZN
MOTOR ASSY.,FOCUS
RETAINING RING
Circuit Diagrams
52