Documente Academic
Documente Profesional
Documente Cultură
13
71236036
Products
Solutions
Services
Technical information
Soliphant M
FTM50, FTM51, FTM52
Vibronic
Table of contents
Function and system design . . . . . . . . . . . . . . . . . . . . . .3
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cable specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Connecting cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring range (detection range) . . . . . . . . . . . . . . . . . . . . . .
Input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
4
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch-on behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fail-safe mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
5
5
Electronic insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FEM51 electronic insert (AC 2wire) . . . . . . . . . . . . . . . . . . . . . 5
FEM52 electronic insert (DC PNP) . . . . . . . . . . . . . . . . . . . . . . . 6
FEM54 electronic insert (AC/DC with relay output) . . . . . . . . 7
FEM55 electronic insert (8/16 mA) . . . . . . . . . . . . . . . . . . . . . . 8
FEM58 electronic insert (NAMUR H-L edge) . . . . . . . . . . . . . . 9
FEM57 electronic insert (PFM) . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
12
12
12
12
12
12
19
19
20
21
21
Operability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating elements of FEM51, FEM52, FEM54,
FEM55, FEM58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating elements of FEM57 . . . . . . . . . . . . . . . . . . . . . . . . .
Sediment detection with FTM50 and FTM51 . . . . . . . . . . . . .
22
23
24
24
25
25
25
25
26
26
26
26
26
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Soliphant M FTM50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Soliphant M FTM51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Soliphant M FTM52 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weather protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rope shortening kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
33
33
33
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Functional safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Medium temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting medium pressure range . . . . . . . . . . . . . . . . . . . . . . .
State of aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grain size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulk weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lateral load (static) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tensile strength rope FTM52 . . . . . . . . . . . . . . . . . . . . . . . . . .
12
13
13
13
13
13
14
14
Mechanical construction . . . . . . . . . . . . . . . . . . . . . . . 15
Housing and process connection . . . . . . . . . . . . . . . . . . . . . . . . 15
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Versions with extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Endress+Hauser
A piezoelectric drive excites the tuning fork of Soliphant M to its resonance frequency. If medium
covers the tuning fork, the fork's vibrating amplitude changes (the vibration is damped). Soliphant M's
electronics compare the actual amplitude with a target value and indicate whether the tuning fork is
vibrating freely or whether it is covered by medium.
L00FTM5xxxx1506xxxx001
A: Amplitude
t: Time
Measuring system
The measuring system is available either with compact instrumentation or separate instrumentation
with a switching unit. The following electronic versions are available:
Compact instrumentation
FEM51:
Two-wire AC version
Switch the load directly into the power supply circuit via the thyristor
FEM52:
Three-wire DC version
Switch the load via the transistor (PNP) and
separate connection
FEM54:
Universal current version with relay output
Switch the loads via 2 floating change-over contacts (DPDT)
L00FTM5xxxx1505xxxx000
Electronic version
1
Ex i
FEM55:
Signal transmission 8/16 mA along two-wire
cabling:
FEM58:
Signal transmission H-L edge 2.2 to 4.8 / 0.4 to
1.0 mA to EN 50227 (NAMUR) along two-wire
cabling
Checking of connecting cabling and other
devices by pressing a key on the electronic
insert
Endress+Hauser
FEM57:
PFM signal transmission
Current pulses superposed on the power supply
along the two-wire cabling
Self-test from the switching unit without
changing levels
L00FTM5xxxx1505xxen000
1
2
Electronic version
Switching unit, PLC, isolating amplifier, segment coupler
Cable specifications
Within the indicated standards and guidelines to interference immunity (see also "Electromagnetic
compatibility", 12) a normal instrument cable is sufficient. If higher interference levels are
present, a shielded cable must be used.
Immunity to temperature change of connecting cable
The connecting cables must withstand the ambient temperature +5 K.
Connecting cables
Electronic inserts: cross-section max. 2.5 mm(13 AWG); strand in ferrule to DIN 46228
Protective ground in housing: cross-section max. 2.5 mm(13 AWG)
Equipotential bonding connection on housing: cross-section max. 4 mm(11 AWG)
Cable entry
Input
Measured variable
Input signal
Measuring frequency
Output
Galvanic isolation
Switch-on behavior
When the power supply is switched on the switching status of the outputs corresponds to "signal on
alarm". The correct switching status is assumed after a maximum of 3 s.
Fail-safe mode
Endress+Hauser
Switching delay
Switch behavior
Binary
Electronic insert
FEM51 electronic insert (AC
2wire)
Power supply
Supply voltage AC: 19 to 253 V
Power consumption: < 1.0 W
Residual current consumption (IR): < 4 mA; 5.5 mA for short fork (in switch-off moment < 1 mA for
100 ms)
Short-circuit protection
Separation voltage: 3.6 kV
FEM51 overvoltage protection: overvoltage category II
Two-wire AC connection
Always connect in series with a load!
Check the following:
the residual current consumption in blocked state.
that for low voltage
the voltage drop across the load
is such that the minimum terminal
voltage at the electronic insert (19 V)
when blocked is not undershot.
the voltage drop across the electronics when switched through is
observed (up to 12 V).
when selecting the relay, pay attention to the holding power/rated
power (see "Connectable load").
1 2
19 V
*
F
1A
L1
**
PE
L00-FTM5xxxx-04-05-xx-xx-024
Output signal
IL
IR
Safety mode
Level
Output signal
IL
LEDs
green yellow red
MAX
1
= flashes
= unlit
IR
IL
MIN
1
Maintenance
required *
Instrument failure
1
IR
IL / IR
IR
2
L00FTM5xxxx0405xxen001
Endress+Hauser
Signal on alarm
Output signal on power failure or in the event of device failure: IR
Connectable load
For relays with a minimum holding power/rated power > 2.5 VA at 253 V (10 mA) or > 0.5 VA at
24 V (20 mA)
For relays with a maximum holding power/rated power < 89 VA at 253 V or 8.4 VA at 24 V
Voltage drop across FEM51 max. 12 V
Residual current with blocked thyristor max. 4 mA (5.5 mA for short fork)
Load current max. 350 mA (short-circuit proof)
FEM52 electronic insert
(DC PNP)
Power supply
DC voltage: 10 to 55 V
Ripple: max. 1.7 V, 0 to 400 Hz
Current consumption: max. 16 mA
Power consumption: max. 0.86 W
Reverse polarity protection/short-circuit protection
Separation voltage: 3.6 kV
FEM52 overvoltage protection: overvoltage category III
Three-wire DC connection
Preferably used with programmable logic controllers
(PLC), DI modules as per EN 61131-2.
Positive signal at switching output of the electronics (PNP).
1 2
(+)
F
0.5A
L+ L
L00-FTM5xxxx-04-05-xx-xx-027
DC: U% 10 V to 55 V
Output signal
IL
IR
Safety mode
Output signal
Level
L+
1
IL
LEDs
green yellow red
+
3
MAX
1
IR
= flashes
= unlit
L+
1
IL
+
3
MIN
1
Maintenance
required *
Instrument failure
1
IR
IL / IR
IR
3
L00FTM5xxxx0405xxen007
Signal on alarm
Output signal on power failure or in the event of device failure: < 100 A
Endress+Hauser
Connectable load
Power supply
Alternating voltage AC: 19 to 253 V, 50/60 Hz
DC voltage: 19 to 55 V
Power consumption: max. 1.5 W
Reverse polarity protection/short-circuit protection
Separation voltage: 3.6 kV
FEM54 overvoltage protection: overvoltage category II
Universal current connection with relay output (DPDT)
Note!
Please note the different voltage ranges for AC and
DC.
Output:
When connecting a device with high inductance,
provide a spark arrester to protect the relay contact.
A fine-wire fuse (depending on the load connected)
protects the relay contact on short-circuiting. The
relay contacts switch simultaneously.
* When jumpered, the relay output works
with NPN logic.
1 2
3 4 56 7 8
F
0.5A
*
L1 N
L+ L
NO C
a u
NC NO C
r
a u
**
**
1
NC
r
L00-FTM5xxxx-04-05-xx-xx-003
Output signal
= relay energized
Safety mode
Level
Output signal
LEDs
green yellow red
= relay de-energized
= lit
MAX
= flashes
3 4 5
6 7 8
3 4 5
6 7 8
3 4 5
6 7 8
3 4 5
6 7 8
3 4 5
6 7 8
= unlit
* See also "Operating elements",
23
MIN
Maintenance
required *
Instrument failure
L00FTM5xxxx0405xxen008
Signal on alarm
Output signal on power failure or in the event of device failure: relay de-energized
Endress+Hauser
Connectable load
Power supply
DC supply voltage: 11 to 36 V
Power consumption: < 600 mW
Reverse polarity protection/short-circuit protection
Separation voltage: 3.6 kV
FEM55 overvoltage protection: overvoltage category III
Two-wire connection
for separate switching unit
For connecting to programmable logic controllers
(PLC), AI modules 4-20 mA to EN 61131-2.
Output signal jump from high to low current on
point level.
1 2
EX
Ex ia
EX
+
L00-FTM5xxxx-04-05-xx-xx-000
U 11 to 36 e.g. PLC
Output signal
16 mA = 16 mA 5 %
8 mA
Safety mode
= 8 mA 6 %
= lit
Output signal
+
2
~16 mA
+
2
~8 mA
+
2
~16 mA
+
2
~8 mA
+
2
8/16 mA
LEDs
green yellow red
MAX
= flashes
= unlit
* See also "Operating elements", 23
Level
MIN
Maintenance
required *
MAX
MIN
OFF
ON
3.6 mA
Instrument failure
+
2
3.6 mA
1
L00FTM5xxxx0405xxen006
Signal on alarm
Output signal on power failure or in the event of device failure: < 3.6 mA
Endress+Hauser
Connectable load
R = (U - 11 V) / 16.8 mA
U = connection DC voltage 11 V to 36 V
FEM58 electronic insert
(NAMUR H-L edge)
Note!
Only in combination with standard fork (fork length 155 mm (6.1 in)).
Power supply
Two-wire connection
for separate switching unit
For connecting to isolating amplifiers
acc. to NAMUR (IEC 60947-5-6), z.B. FTL325N or
FTL375N from Endress+Hauser.
H-L edge:
Output signal jump from high to low current on
point level.
1 2
Additional function:
Test key on the electronic insert.
Pressing the key breaks the connection to the
isolating amplifier.
H
I
L
Note!
For Ex d applications, the additional function can
only be used if the housing is not exposed
to an explosive atmosphere.
Connecting to multiplexer:
Set clock time to min. 5 s.
EX
Ex ia
EX
+
L00-FTM5xxxx-04-05-xx-xx-005
Output signal
= lit
Safety mode
Level
Output signal
= flashes
= unlit
MAX
+
2
+
2
+
2
MIN
+
2
Maintenance
required *
+
2
Instrument failure
+
2
2.2
4.8 mA
0.4
1.0 mA
2.2
4.8 mA
0.4
1.0 mA
0.4
4.8 mA
0.4
1.0 mA
LEDs
green yellow red
1
L00FTM5xxxx0405xxen012
Signal on alarm
Output signal
in event of device failure: < 1.0 mA
Endress+Hauser
Connectable load
See "Technical Data" of the isolating amplifier connected according to IEC 6094756 (NAMUR)
Connection also to safety isolating amplifiers (I = 3 to 4.8 mA)
FEM57 electronic insert
(PFM)
Power supply
Two-wire connection
for separate switching unit
For connecting to Nivotester (see graphic) from
Endress+Hauser.
Output signal jump of PFM signal from high to low
frequency when sensor is covered. Switching
between minimum/maximum safety on the
Nivotester.
Additional function "self test:
After interruption of the power supply, a test cycle
is activated which checks the sensor and electronics
without any change in level.
For this purpose, the operating elements must be
configured
as follows:
OFF
ON
1 2
EX
Ex ia
PFM
50/
150 Hz
EX
OFF
ON
+
1: FTL325P (1CH)
2: FTL325P (3CH)
33
34
37
38
d4
d2
3: FTL375P (1CH)
z4
z2
4: FTL375P (2CH)
z6
d6
5: FTL375P (3CH)
L00-FTM5xxxx-04-05-xx-xx-006
Output signal
= lit
Safety mode
Level
= flashes
Output signal
(PFM)
LEDs
green yellow red
150 Hz
= unlit
50 Hz
150 Hz
OFF
ON
OFF
ON
0 Hz
Instrument failure
0 Hz
L00FTM5xxxx0405xxen009
Signal on alarm
Output signal on power failure or in the event of device failure: 0 Hz
Connectable load
Floating relay contacts in connected switching unit Nivotester (see drawing above)
10
Endress+Hauser
For contact load, see the Technical Data of the switching unit
Installation
Orientation FTM50
max.
60 (2.36)
Installation instructions
~20
~250 (9.84)
~200
(7.87)
mm (in)
L00-FTM5xxxx-11-06-xx-xx-004
Orientation
FTM51, FTM52
A
1
L
B
L00FTM5xxxx1106xxxx001
1 Sliding sleeve; 2 FTM51; 3 FTM52; 4 FTM51 with supporting tube (not included in the delivery)
A Clearance
B Maximum nozzle length: L 145 mm (5.71 in) for short fork or L 200 mm (7.87 in) for standard fork
Endress+Hauser
11
Environment
Ambient temperature range
Storage temperature
Climate class
Degree of protection
Vibration resistance
Shock resistance
To EN 60068-2-27: 30 g
Electrical safety
Electromagnetic compatibility
Process
Medium temperature limits
Ta
Ta
FTM52
FTM50/51
**
70 (158)
50 (122)
Tp
40 (40)
80 (176)
0 (32)
50 (58)
0 (32)
50 (122)
100 (212)
150 (302)
Tp
90 (194)
F16*
40 (40)
50 (58)
L00-FTM5xxxx-05-05-xx-xx-003
12
Endress+Hauser
Ta
***
**
70 (158)
Ta
50 (122)
Tp
0 (32)
50 (58)
0 (32)
50 (122)
230 (446)
190 (374)
F16*
280 (536)
Tp
40 (40)
50 (58)
L00-FTM5xxxx-05-05-xx-xx-005
Maximum 120 K
At high temperature 260 K
State of aggregation
Solids
Grain size
10 mm (0.39 in)
Bulk weight
Endress+Hauser
13
The following graphic shows the maximum permitted lateral load F in N (lbf) in relation to the length
L in mm (in).
1000 (224.80)
900 (202.32)
800 (179.84)
750 (168.60)
700 (157.36)
650 (146.12)
600 (134.88)
550 (123.64)
500 (112.40)
450 (101.16)
400 (89.92)
350 (78.68)
300 (67.44)
250 (56.20)
200 (44.96)
150 (33.72)
100 (22.48)
50 (11.24)
0
L
B
6000 (236)
5500 (217)
5000 (197)
4500 (177)
4000 (157)
3500 (138)
3000 (118)
2500 (98.4)
2000 (78.7)
1500 (59.1)
1000 (39.4)
500 (19.7)
L00-FTM5xxxx-05-05-xx-en-001
14
3000 N (lbf)
Endress+Hauser
Mechanical construction
Polyester housing F16
85 (3.35)
max. 76 (2.99)
100 (3.94)
Process connection:
R 1
1 NPT
1 NPT
43 (1.69)
Housing
and process connection
22.5 (0.89)
mm (in)
L00FTM5xxxx0605xxxx008
max. 64 (2.52)
28 (1.1)
94 (3.7)
113* (4.45*)
Process connection:
Tri-Clamp
76 (3.0)
22,5 (0.9)
mm (in)
L00-FTM5xxxx-06-05-xx-xx-049
max.65 (2.56)
80 (3.15)
43 (1.69)
119* (4.69*)
Process connection:
Flange
max.60 (2.36)
105 (4.13)
22,5 (0.9)
mm (in)
L00-FTM5xxxx-06-05-xx-xx-050
Endress+Hauser
15
118 (4.65)
51** (2.01)
Process connection
Flange
R1
1 NPT
1 NPT
80 (3.15)
133* (5.24)
max. 65 (2.56)
53 (2.09)
Process connection
Flange
R1
1 NPT
1 NPT
max. 60 (2.36)
mm (in)
L00-FTM5xxxx-06-05-xx-xx-051
41** (1.61**)
135 (5.31)
148* (5.83*)
Process connection
R1
1 NPT
1 NPT
max. 97 (3.82)
max. 65 (2.56)
22,5 (0.9)
mm (in)
L00-FTM5xxxx-06-05-xx-xx-052
16
Endress+Hauser
Dimensions
Code Dimensions
1 NPT
ANSI B 1.20.1
GJ
R 1
EN 10226
GG
Accessories
max. 25 bar
(362.5 psi)
max. 280 C (536 F)
50
43
(1.69)
200(7.87)1)/145(5.71)2)
24.5
(0.96)
Pressure
Temperature
(for FTM50/51)
L00FTM5xxxx0605xxxx004
GX
max. 25 bar
(362.5 psi)
max. 150 C (302 F)
2)
145 (5.71)
24.5
(0.96)
50
36
(1.42)
1 NPT
ANSI B 1.20.1
L00-FTM5xxxx-06-05-xx-xx-006
GK
max. 25 bar
(362.5 psi)
max. 150 C (302 F)
145 (5.71)2)
24.5
(0.96)
45
36
(1.42)
1 NPT
ANSI B 1.20.1
L00-FTM5xxxx-06-05-xx-xx-005
A#
B#
K#
1)
2)
Seal
according to
design
installed on
site
FDA approval
available
Clamping ring
and
front seal
installed on
site
FDA approval
available
43 (1.69)
Flange
ANSI B 16.5
EN 1092-1
(DIN 2527 B)
JIS B2220
L00-FTM5xxxx-06-05-xx-xx-013
TD
215(8.46)1)/160(6.3)2)
43
(1.69)
Tri-Clamp 2"
ISO 2852
L00-FTM5xxxx-06-05-xx-xx-014
4
(0.16)
39
(1.54)
36
(1.42)
100
(3.94)
155
(6.1)
15
(0.59)
43
(1.69)
100
(3.94)
43
(1.69)
39
(1.54)
32
(1.26)
L00-FTM5xxxx-06-05-xx-xx-030
Endress+Hauser
17
65 (2.56)
Ex d(e), XP: 105 (4.13)
129 (5.08)
Ex d(e), XP: 169 (6.65)
140 (5.51)
204 (8.03)
D2
D1
D1
D2
mm (in)
L00-FTM5xxxx-06-05-xx-xx-015
Process connection:
Versions with
extensions
GK, GX
D1 (mm [in])
43 (1.69)
36 (1.42)
D2 (mm [in])
37 (1.46)
37 (1.46)
FMI51 (pipe): Dimensions depend on process connection and selected pipe extension
FTM52 (rope): Dimensions depend on process connection and selected rope extension
Process
1 NPT
connection: 1 NPT
R 1
FTM52
FTM51
FTM52
FTM51
L00-FTM5xxxx-06-05-xx-xx-016
L00-FTM5xxxx-06-05-xx-xx-017
L00-FTM5xxxx-06-05-xx-xx-018
L00-FTM5xxxx-06-05-xx-xx-022
18
Endress+Hauser
280 C (536 F)
150 C (302 F)
Versions with
temperature spacer
L00-FTM5xxxx-06-05-xx-xx-019
mm (in)
150 C (302 F)
L00-FTM5xxxx-06-05-xx-xx-020
L00-FTM5xxxx-06-05-xx-xx-021
230 C (446 F)
280 C (536 F)
145 (5.71)
--
175 (6.89)
215 (8.46)
145 (5.71)
165 (6.5)
165 (6.5)
205 (8.07)
Not relevant
Not relevant
Certificate
A, 1, 2, 3, 4, 7, 8, 5, 6, H, Z
C, D, F, X
Surface refinement
Electropolishing
2
1
L00-FTM5xxxx-06-05-xx-xx-031
L00-FTM5xxxx-06-05-xx-xx-002
NOTICE
In the area of the welding seam, the surface roughness depends on the production technique and is not
defined.
Coating
1
2
3
L00-FTM5xxxx-06-05-xx-xx-032
L00-FTM5xxxx-06-05-xx-xx-003
1: Fork coated
2: Fork and pipe coated as far as welding seam on process connection
3: Fully coated
Endress+Hauser
19
Applications:
For high ambient temperatures and applications with confined installation locations (e.g. filling nozzle
applications). The cable between the separate housing and sensor can be shortened at the customer's.
EX
Tp
A
Ta1
Ta2
L00-FTM5xxxx-15-06-xx-en-002
Ta1
Ta2
Tp
FTM50/51
70 C (158 F) 120 C (248 F) Versions: 150 C (302 F), 230 C (446 F), 280 C (536 F)
FTM52
70 C (158 F) 80 C (176 F)
80 C (176 F)
H1
H2
H1
H21)
H3
H3
34 (1.34)
108 (4.25)2)
~75 (2.95)
1)
~61 (2.4)
3)
r
21 (0.83)
mm (in)
L00-FTM5xxxx-06-05-xx-xx-023
Dimensions
Polyester
mm (in)
(F16)
Stainless
steel (F15)
Aluminum
(F17)
Aluminum (F13)
Stainless steel
(F27)
Aluminum (T13)
Separate connection compartment
76 (2.99)
64 (2.52)
65 (2.56)
65 (2.56)
97 (3.82)
H1
155 (6.1)
166 (6.54)
160 (6.3)
243 (9.57)
260 (10.2)
185 (7.28)
174 (6.85)
258 (10.2)
273 (10.7)
H2
H3
20
-41 (1.61)
Housing
62 (2.44)
Endress+Hauser
Weights
Depends on type; see last column on "Additional weight" in the ordering information
Endress+Hauser
21
Operability
Display elements
NOTICE
The switch settings in the following graphics are in the as-delivered state.
FEM51
Green LED lit:
Indicates operational status
Yellow LED lit:
Indicates switching status
Red LED
flashing: flashes alternately with green LED
if maintenance is required
lit: indicates device failure
L1
MAX
MIN
OFF
ON
FEM51
AC
U ~ 19...253V AC
50/60Hz
I max : 350mA
L00FTM5xxxx0305xxxx001
FEM52
Green LED lit:
Indicates operational status
Yellow LED lit:
Indicates switching status
Red LED
flashing: indicates maintenance is required
lit: indicates device failure
MAX
MIN
OFF
ON
L+
FEM52
L-
DC PNP
U 10...55V DC
I max : 350mA
L00FTM5xxxx0305xxxx002
FEM54
Green LED lit:
Indicates operational status
Yellow LED lit:
Indicates switching status
Red LED
flashing: indicates maintenance is required
lit: indicates device failure
MAX
3 5 MIN
U~
19... 55V DC
4
19... 253V AC
L1
OFF
ON
FEM54
3 5 68
4
L00FTM5xxxx0305xxxx004
FEM55
Green LED lit:
Indicates operational status
Yellow LED lit:
Indicates switching status
Red LED
flashing: indicates maintenance is required
lit: indicates device failure
I = 16mA
U
11...36V DC
MAX
MIN
OFF
ON
FEM55
8/16mA
L00FTM5xxxx0305xxxx005
22
Endress+Hauser
FEM57
Green LED lit:
Indicates operational status
Yellow LED lit:
Indicates covered status
Red LED
flashing: indicates maintenance is required
lit: indicates device failure
FEM57
PFM
OFF
ON
OFF
ON
L00FTM5xxxx0305xxxx007
FEM58
Green LED flashing:
Indicates operational status
Yellow LED lit:
Indicates switching status
Red LED
flashing: flashes alternately with green LED
if maintenance is required
flashing: indicates device failure
FEM58
NAMUR
IEC 60947-5-6
OFF
ON
MAX
MIN
> 2,2mA
L00FTM5xxxx0305xxxx008
NOTICE
If the test key is pressed this breaks the cable connection.
Operating elements of
FEM51, FEM52, FEM54,
FEM55, FEM58
Factory setting:
OFF
ON
MAX
MIN
L00-FTM5xxxx-19-05-xx-xx-001
Overfill prevention
MIN
Endress+Hauser
23
Operating elements of
FEM57
Factory setting:
OFF
ON
OFF
ON
L00FTM5xxxx1905xxxx002
ON
OFF
ON
H2O
Hinweis!
Switching sensitivity decreases if a short
fork is used.
L00-FTM5xxxx-19-05-xx-xx-014
24
Endress+Hauser
The device is designed to meet state-of-the-art safety requirements, has been tested and left the
factory in a condition in which it is safe to operate.
The device complies with the applicable standards and regulations as listed in the EC Declaration of
Conformity and thus complies with the statutory requirements of the EC directives.
Endress+Hauser confirms the successful testing of the device by affixing to it the CE mark.
Ex approval
Dust ignition-proof
F15
housing
F17
housing
F13 / F27
housing
T13 housing
with separate
connection
compartment
Separate
housing
X
(except II 1/2 D)
Ex ia
Ex nA/nL/nC
Ex d
Ex de
IP66/67
IP66/68
Recommended in
event of severe external vibrations
Goretex filter
Other standards and guidelines that were taken into consideration in designing and developing
Soliphant M FTM50, FTM51, FTM52:
Low Voltage Directive
(73/23/EEC)
DIN EN 61010 Part 1, 2001
Protection Measures for Electrical Equipment for Measurement, Control, Regulation and Laboratory
Procedures
Part 1: General requirements
EN 61326
Electrical Equipment for Measurement, Control and Laboratory Use
EMC requirements
C-tick mark
The measuring system meets the EMC requirements of the "Australian Communications and Media
Authority (ACMA)".
Endress+Hauser
25
CRN approval
CRN-approved devices are fitted with a separate plate bearing the registration number
No.: 0F10907:5C ADD1.
ASME B 31.3
Design and materials in accordance with ASME B31.3. The welding seams are through-penetration
welded and comply with ASME Boiler and Pressure Vessel Code Section IX and EN ISO 15614-1.
Type
Soliphant M
FTM50-D/F/H##...
FTM51-D/F/H##...
FTM52-D/F/H##...
Marking
Approval
Single Seal
Single Seal
Single Seal
FM, CSA
FM, CSA
FM, CSA
Other certificates
Use in safety systems requiring functional safety to SIL2 in accordance with IEC 61508. See
"Documentation", 35.
26
Endress+Hauser
Ordering information
NOTICE
This overview does not mark options which are mutually exclusive.
Soliphant
M FTM50
Basic weight: (F16 housing, thread R 1, fork 100 mm, 50g/l): 1.1 kg (2.43 lbs)
010
Approval
A
C
D
E
F
G
H
S
T
X
Z
8
1
2
3
4
5
6
7
Y
020
Non-hazardous area
CSA General Purpose, CSA C/US
FM DIP-AIS Cl. II, III, Div. 1, Gr. E-G + CSA DIP Cl. II, III, Div. 1+2, Gr. E-G, Zone 2, 21, 22
IEC Ex iaD A20, IEC Ex ia IIC T6
FM IS Cl. I, II, III, Div. 1, Gr. A-G + NI + CSA IS
Cl. I, II, III, Div. 1+2, Gr. A-G, FM: Zone 0, 1, 2, 20, 21, 22; CSA: Zone 0, 1, 2
IEC Ex tD A20/A21
FM XP-AIS Cl. I, Div. 1, Gr. A-D + CSA XP Cl. I, Div. 1+2, Gr. A-D, FM: Zone 1, 2, 21, 22; CSA: Zone 1, 2
TIIS Ex d IIC T3
TIIS Ex ia IIC T3
NEPSI Ex ia IIC T2-T6
NEPSI Ex d IIC T2-T6
NEPSI DIP A20/A21 TA, T* IP66
ATEX II 1 D, 1/2 GD, 1/3 GD Ex ia IIC T6
ATEX II 1/2 D Ex tD
ATEX II 3 D, ATEX II 3 G Ex nA/nL/nC
ATEX II 1/3 D Ex tD
ATEX II 1 D, ATEX II 1/2 G Ex de [ia] IIC T6
ATEX II 1 D, ATEX II 1/2 G Ex d [ia] IIC T6
ATEX II 1 G/D, Ex ia IIC T6, note Safety Instructions (XA)!
Special version, TSP-No. to be spec.
Process connection
AF
AG
AH
B3
BS
BT
GG
GJ
GK
GX
KF
KG
KH
TD
YY
030
050
Additional weight
0.1 kg
Electronics; output
1
2
4
5
7
8
9
Endress+Hauser
2.5 kg
5.0 kg
7.1 kg
3.3 kg
4.9 kg
5.7 kg
1.8 kg
3.3 kg
4.4 kg
040
Additional weight
27
060
Probe design
A
D
E
G
H
Y
070
Housing
H
1
3
5
6
7
Y
080
Additional weight
1.1 kg
0.4 kg
0.5 kg
0.5 kg
0.1 kg
Cable entry
Gland M20 (Ex d > thread M20)
Thread NPT
Thread G
Thread NPT
Special version, TSP-No. to be spec.
Additional options 1
A
G
R
S
Y
100
2.4 kg
2.4 kg
5.0 kg
5.0 kg
2
3
4
7
9
090
Additional weight
Compact
6 m cable > separate housing
20 ft cable > separate housing
6 m cable, armored > separate housing
20 ft cable, armored > separate housing
Special version, TSP-No. to be spec.
Additional weight
Not selected
Glass cover
Glass cover, SIL Declaration of Conformity
SIL Declaration of Conformity
Special version, TSP-No. to be spec.
Additional options 2
0.1 kg
0.1 kg
Additional weight
A Not selected
C EN10204-3.1 material (wetted),
inspection certificate
D Temperature spacer 150 C
E Temperature spacer 150 C,
EN10204-3.1 material (wetted), inspection certificate
F High temperature 280 C
H High temperature 280 C,
EN 10204-3,1 material (wetted), inspection certificate
J High temperature 230 C
K High temperature 230 C,
EN 10204-3,1 material (wetted), inspection certificate
Y Special version
0.4 kg*
0.4 kg*
1.0 kg
1.0 kg
0.9 kg
0.9 kg
995
Identification
1
FTM50
-
28
Endress+Hauser
Soliphant M FTM51
Basic weight: (F16 housing, thread R 1, length 300 mm, 50 g/l): 1.4 kg (3.09 lbs)
010
Approval
A
C
D
E
F
G
H
S
T
X
Z
8
1
2
3
4
5
6
7
Y
020
Non-hazardous area
CSA General Purpose, CSA C/US
FM DIP-AIS Cl. II, III, Div. 1, Gr. E-G + CSA DIP
Cl. II, III, Div. 1+2, Gr. E-G, FM: Zone 21, 22
IEC Ex iaD A20, IEC Ex ia IIC T6
FM IS Cl. I, II, III, Div. 1, Gr. A-G + NI + CSA IS
Cl. I, II, III, Div. 1+2, Gr. A-G; FM: Zone 0, 1, 2, 20, 21, 22; CSA: Zone 0, 1, 2
IEC Ex tD A20/A21
FM XP-AIS Cl. I, Div. 1, Gr. A-D + CSA XP
Cl. I, Div. 1+2, Gr. A-D, FM: Zone 1, 2, 21, 22; CSA: Zone 1, 2
TIIS Ex d [ia] IIC T4
TIIS Ex ia IIC T3
NEPSI Ex ia IIC T2-T6
NEPSI Ex d [ia] IIC T2-T6
NEPSI DIP A20 Ta, T4
ATEX II 1 D, 1/2 GD, 1/3 GD Ex ia IIC T6
ATEX II 1/2 D Ex tD
ATEX II 3 D, ATEX II 3 G Ex nA/nL/nC
ATEX II 1/3 D Ex tD
ATEX II 1 D, ATEX II 1/2 G Ex de [ia] IIC T6
ATEX II 1 D, ATEX II 1/2 G Ex d [ia] IIC T6
ATEX II 1 G/D, Ex ia IIC T6, note Safety Instructions (XA)!
Special version, TSP-No. to be spec.
Process connection
AF
AG
AH
B3
BS
BT
GG
GJ
GK
GX
KF
KG
KH
TD
YY
030
2.5 kg
5.0 kg
7.1 kg
3.3 kg
4.9 kg
5.7 kg
1.8 kg
3.3 kg
4.4 kg
040
Additional weight
...
mm; min. 10 g/l
...
mm; min. 50 g/l
... in; min. 10 g/l
... in; min. 50 g/l
... mm; min. 10 g/l, surface refinement
... mm; min. 50 g/l, surface refinement
... in; min. 10 g/l, surface refinement
... in; min. 50 g/l, surface refinement
Special version, TSP-No. to be spec.
Additional weight
2.0 kg/m*
2.0 kg/m*
5.1 kg/100 in*
5.1 kg/100 in*
2.0 kg/m*
2.0 kg/m*
5.1 kg/100 in*
5.1 kg/100 in*
050
Electronics; output
1
2
Endress+Hauser
29
050
Electronics; output
4
5
7
8
9
060
Probe design
A
D
E
G
H
Y
070
Housing:
H
1
3
5
6
7
Y
080
Additional weight
1.1 kg
0.4 kg
0.5 kg
0.5 kg
0.1 kg
Cable entry
Gland M20 (Ex d > thread M20)
Thread NPT
Thread G
Thread NPT
Special version, TSP-No. to be spec.
Additional options 1
A
G
R
S
Y
100
2.4 kg
2.4 kg
5.0 kg
5.0 kg
2
3
4
7
9
090
Additional weight
Compact
6 m cable > separate housing
20 ft cable > separate housing
6 m cable, armored > separate housing
20 ft cable, armored > separate housing
Special version, TSP-No. to be spec.
Additional weight
Not selected
Glass cover
Glass cover, SIL Declaration of Conformity
SIL Declaration of Conformity
Special version, TSP-No. to be spec.
Additional options 2
A
C
D
E
F
H
J
K
Y
0.1 kg
0.1 kg
Additional weight
Not selected
EN10204-3.1 material (wetted),
inspection certificate
Temp. spacer 150 C
Temp. spacer 150 C,
EN10204-3.1 material (wetted), inspection certificate
High temperature 280 C
High temperature 280 C,
EN10204-3.1 material (wetted), inspection certificate
High temperature 230 C
High temperature 230 C,
EN10204-3.1 material (wetted), inspection certificate
Special version, TSP-No. to be spec.
0.4 kg*
0.4 kg*
1.0 kg
1.0 kg
0.9 kg
0.9 kg
995
Identification
1
FTM51
-
30
Endress+Hauser
Soliphant M FTM52
Basic weight: (F16 housing, thread R 1, length 1000 mm, 50 g/l): 2.2 kg (4.85 lbs)
010
Approval
A
C
D
E
F
G
H
S
T
X
Z
8
1
2
3
4
5
6
7
Y
020
Non-hazardous area
CSA General Purpose, CSA C/US
FM DIP-AIS Cl. II, III, Div. 1, Gr. E-G + CSA DIP
Cl. II, III, Div. 1+2, Gr. E-G, FM: Zone 21, 22
IEC Ex iaD A20, IEC Ex ia IIC T6
FM IS Cl. I, II, III, Div. 1, Gr. A-G + NI + CSA IS
Cl. I, II, III, Div. 1+2, Gr. A-G, FM: Zone 0, 1, 2, 20, 21, 22; CSA: Zone 0, 1, 2
IEC Ex tD A20/A21
FM XP-AIS Cl. I, Div. 1, Gr. A-D + CSA XP
Cl. I, Div. 1+2, Gr. A-D, FM: Zone 1, 2, 21, 22; CSA: Zone 1, 2
TIIS Ex d [ia] IIC T6
TIIS Ex ia IIC T3 (in preparation)
NEPSI Ex ia IIC T6
NEPSI Ex d [ia] IIC T6
NEPSI DIP A20/A21 TA, T* IP66
ATEX II 1D, 1/2 GD, 1/3 GD Ex ia IIC T6
ATEX II 1/2 D Ex tD [iaD]
ATEX II 3D, ATEX II 3 G Ex nA/nL/nC
ATEX II 1/3 D Ex tD [iaD]
ATEX II 1 D, ATEX II 1/2 G Ex de [ia] IIC T6
ATEX II 1 D, ATEX II 1/2 G Ex d [ia] IIC T6
ATEX II 1G/D Ex ia IIC T6, note Safety instructions (XA)!
Special version, TSP-No. to be spec.
Process connection
AF
AG
AH
B3
BS
BT
GG
GJ
GK
GX
KF
KG
KH
TD
YY
030
050
...
mm; min. 10 g/l
...
mm; min. 50 g/l
... in; min. 10 g/l
... in; min. 50 g/l
Special version, TSP-No. to be spec.
1.3 kg/10 m
1.3 kg/10 m
1.7 kg/500 in
1.7 kg/500 in
Probe design
A
D
Endress+Hauser
Additional weight
Electronics; output
1
2
4
5
7
8
9
060
2.5 kg
5.0 kg
7.1 kg
3.3 kg
4.9 kg
5.7 kg
1.8 kg
3.3 kg
4.4 kg
040
Additional weight
Compact
6 m cable > separate housing
Additional weight
2.4 kg
31
060
Probe design
E
G
H
Y
070
Housing
H
1
3
5
6
7
Y
080
Additional weight
Additional options 1
Not selected
Glass cover
Glass cover, SIL Declaration of Conformity
SIL Declaration of Conformity
Special version, TSP-No. to be spec.
32
Additional weight
0.1 kg
0.1 kg
Additional options 2
Not selected
Special version, TSP-No. to be spec.
Identification
1
FTM52
-
0.4 kg
0.5 kg
0.5 kg
0.1 kg
A
Y
995
1.1 kg
Cable entry
A
G
R
S
Y
100
2.4 kg
5.0 kg
5.0 kg
2
3
4
7
9
090
Additional weight
Endress+Hauser
PA
102
(4.02)
Removing tool
~1
(4 10
.3 3
)
Accessories
162
(6.3
8)
L00-FTM5xxxx-03-05-xx-xx-009
80 (3.15)
NOTICE
Suitable for switch point configuration!
70
~75
(2.95)
M6x25
5
Sliding sleeve
E
mm (in)
L00FTM5xxxx0305xxxx002
A G2 (316L)
B 2NPT (316L)
C For G2: 24 mm (0.94 in); for 2NPT: 27.5 mm (1.08 in)
D MWP = 25 bar (362.5 psi)
E Tp = max. 280 C (536 F)
L00-FTM5xxxx-00-00-xx-xx-001
Endress+Hauser
33
Spare parts
Information on the spare parts that are available for your measuring device is provided on our website
"www.endress.com". Proceed as follows here:
1.
2.
Click "Instruments".
3.
4.
5.
6.
Select the spare parts (also use the overview drawings on the right-hand side of the screen).
When ordering a spare part, always indicate the serial number that is indicated on the nameplate.
Where necessary, replacement instructions are provided with the spare parts.
34
Endress+Hauser
Documentation
NOTICE
You can find the following supplementary documentation on our product pages at
www.endress.com.
Operating Instructions
Certificates
ATEX
ATEX II 1 D, II 1/2 GD, II 1/3 GD Ex ia IIC T6: XA00305F
ATEX II 1 D, II 1 G Ex ia IIC T6 (X): XA00319F
ATEX II 1 D, II 1/2 G Ex d/de [ia] IIC T6: XA00306F
ATEX II 1/2 D, II 1/3 D Ex tD: XA00307F
ATEX II 3 D, II 3 G Ex nA/nL/nC: XA00331F
NEPSI DIP: XA00393F
NEPSI Ex ia: XA00394F
NEPSI Ex d [ia]: XA00395F
IEC Ex, Ex ia (in preparation): XA00391F
IEC Ex, Ex tD (in preparation): XA00392F
FM
ZD00218F
CSA
ZD00219F
Functional safety
Endress+Hauser
35
www.addresses.endress.com