Documente Academic
Documente Profesional
Documente Cultură
constructive solutions
Compatibility
Permeability
Setting times
workability
can
be
Initial and final set times will be related to cement type and
ambient temperature.
Figure 1: Conplast R - Initial set time versus dosage at
constant water cement.
Description
Conplast R is supplied as a brown chloride free liquid,
based on a hydroxycarboxylic acid derivative, which
instantly disperses in water.
When added to concrete mixes Conplast R causes the
cement particles to disperse more fully exposing a larger
surface area and enabling the water content to perform,
more efficiently. This effect can be used to improve
workability, to increase ultimate strengths, or to facilitate a
reduction in the cement content.
The retarding properties of Conplast R can also be
beneficial in concrete where high cement content or high
temperatures are involved.
Cold joints in continuous
concrete pours may be avoided and the use of lower
cement content mixes will reduce heat of hydration.
Conplast R is particularly suitable for cohesive and cement
rich mixes. For lean mixes and mixes which are prone to
segregation Conplast RP624 may prove to be more
suitable.
Standards
Conplast R complies with BS 5075 Part 1 and with ASTM
C494, Type D.
Properties
Chloride content:
Specific gravity:
Air entrainment:
Nil to BS 5075
o
1.13 to 1.15 at 20 C
Conplast R acts as a mild air
detrainer.
Page 1
Conplast R
Compressive strength and retardation: Table 1 gives typical results for compressive strength and retardation
Dosage
Ltr/100 kg
Cement
Nil
0.28
0.42
0.56
0.5 N/mm
BS 5075
Initial set
Hours
Minutes
4
30
6
30
8
10
-
3.5 N/mm
BS 5075 Final set
ASTM C403 Initial set
Hours
Minutes
6
8
9
15
11
15
27.6 N/mm
ASTM C403
Final set
Hours
Minutes
7
30
10
11
30
13
30
Strength N/mm
W/C
0.68
0.62
0.58
0.56
3 days
20
24
27
28
7 days
28
35
38
39
28 days
38
46
48
49
Storage
Conplast R has a minimum shelf life of 12 months provided
o
o
the temperature is kept within the range 2 C to 50 C. If this
temperature is exceeded in any respect advice should be
sought from the supplier.
Packaging
Conplast R is supplied in 25 and 210 litre drums. Also in
tanker loads. For larger users storage tanks and dispensing
equipment can be supplied.
Supply
Overdosing
Technical service
The company provides a technical advisory service for on
site assistance and for advice on evaluation trials and
dispensing equipment.
Precautions
Additional information
Fire
Conplast R is non-flammable.
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2
FO SA/CONPLAST R/05/A