Documente Academic
Documente Profesional
Documente Cultură
www.gateforum.com
General aptitude
Q. No. 1 5 Carry One Mark Each
1.
Five teams have to compete in a league, with every team playing every other team exactly
once, before going to the next round. How many matches will have to be held complete
the league round of matches?
(A) 20
Answer:
(B) 10
(C) 8
(D) 5
(B)
(B) False
(C) Uncertain
Answer: (B)
3.
Choose the appropriate word/phase, out of the four options given below, to complete the
following sentence:
Apparent lifelessness ___________ dormant life.
(A) harbours
(b) lead to
(c) supports
(d) affects
Answer: (A)
Exp: Apparent: looks like
dormant: hidden
Harbour: give shelter
Effect (verb): results in
4.
Answer: (B)
Exp:
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
5.
www.gateforum.com
From the statement, it appears that boy found it tough to adapt to a very different
situation.
Q. No. 6 10 Carry Two Marks Each
6.
Right triangle PQR is to be constructed in the xy plane so that the right angle is at P and
line PR is parallel to the-axis. The x and y coordinates of P, Q, and R are to be integers
that satisfy the inequalities: 4 x 5 and 6 y 16. How many different triangles
could be constructed with these properties?
(A) 110
(B) 1,100
(C) 9,900
(D) 10,000
Answer: (C)
Exp:
X1 4 X1 5
Y1 6 Y1 16
X 2 9 chairs X1 X 2
Y2 10 chairs Y1 Y2
Total triangles 10 11 9 10 9900
7.
Given below are two statements followed by two conclusions. Assuming these statements
to be true, decide which one logically follows:
Statements:
I. No manager is a leader.
Conclusions:
I. No manager is a executive.
Answer: (C)
Exp:
Executive
L NL
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
www.gateforum.com
A coin is tossed thrice. Let X be the event that head occurs in each of the first two tosses.
Let Y be the event that a tail occurs on the third toss. Let Z be the event that two tails
occurs in three tosses. Based on the above information, which one of the following
statements is TRUE?
(A) X and Y are not independent
(B) Y and Z are dependent
(C) Y and Z are independent
10.
In the given figure angle Q is a right angle, PS:QS = 3:1, RT:QT = 5:2 and PU:UR = 1:1.
If area of triangle QTS is 20 cm2, then the area of triangle PQR in cm2 is ______.
R
U
Answer: 280
Exp: Let area of triangle PQR be A
SQ
1
1
PQ 1 3 4
QT
2
2
QR 2 5 7
1
Area of le QTS SQ QT
2
1 1
2
PQ QR
2 4
7
1 2 1
PQ QR
4 7 2
1
Area of le PQR
14
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
www.gateforum.com
1
A
14
A 14 20 280cm 2
given 20cm 2
Mechanical Engineering
Q. No. 1 25 Carry One Mark Each
1.
Three parallel pipes connected at the two ends have flow-rates Q1, Q2 and Q3 respectively,
and the corresponding frictional head losses are hL1, hL2 and hL3 respectively. The correct
expressions for total flow rate (Q) and frictional head loss across the two ends (hL) are
(A) Q = Q1 + Q2 + Q3; hL = hL1 + hL2 + hL3
(B) Q = Q1 + Q2 + Q3; hL = hL1 = hL2 = hL3
(C) Q = Q1 = Q2 = Q3; hL = hL1 + hL2 + hL3
(D) Q = Q1 = Q2 = Q3; hL = hL1 = hL2 = hL3
Answer: (B)
Exp:
2.
4 2
The lowest eigen value of the 2 2 matrix
is ________
1 3
Answer: 2
Exp:
4 2
Let A
1 3
Characteristic equation of A is A I 0
4
2
0
1
3
2 7 10 0 2,5
3.
(A) i and iv
Answer: (A)
Exp:
(C) ii and iv
Diffusion welding and friction welding are autogenous welding process as they do not
require any filler material.
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
4.
www.gateforum.com
The strain hardening exponent n of stainless steel SS 304 with distinct yield and UTS
values undergoing plastic deformation is
(A) n < 0
(B) n =0
(C) 0 < n < 1
(D) n = 1
Answer: (C)
Exp:
n lies between 0 and 1. 0 means material is a perfectly plastic solid, while 1 represents a
100% elastic solid.
5.
In the figure, link 2 rotates with constant angular velocity 2. A slider link 3 moves
outwards with a constant relative velocity VQ/P, where Q is a point on slider 3 and P is a
point on link 2. The magnitude and direction of Coriolis component of acceleration is
given by
VQP
Qon 3
P on 2
O
(A) 22 VQ/P; direction of VQ/P rotated by 90 in the direction 2
(B) 2 VQ/P; direction of VQ/P rotated by 90 in the direction 2
(C) 22 VQ/P; direction of VQ/P rotated by 90 opposite to the direction of 2
(D) 2 VQ/P; direction of VQ/P rotated by 90 opposite to the direction 2
Answer: (A)
Exp:
direction is obtained by rotating velocity vector through 90o in the direction of rotation of
the link.
6.
Answer: (D)
Exp:
Coutte flow is steady incompressible, laminar flow between one fixed plate and other
moving with constant velocity.
V
x
7.
1
4
4
25
1
3
29
50
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
www.gateforum.com
Answer: (C)
Exp:
8.
PY X
PX Y
PX
1
1
12
1 3
4
In a machining operation, if the generatrix and directix both are straight lines, the surface
obtained
(A) cylindrical
(B) helical
(C) plane
Answer: (C)
Exp:
9.
A rigid container of volume 0.5 m3 contains 1.0 kg of water at 120C (vf = 0.00106
m3/kg, vg = 0.8908 m3/kg). The state of water is
(A) Compressed liquid
(B) Saturated liquid
(C) A mixture of saturated liquid and saturated vapor
(D) Superheated vapor
Answer: (C)
Exp:
0.5 3
m / kg 0.5m3 / kg
1
Since Vf V Vg the state of water is mixture of saturated water and saturated vapour.
10.
(B) wax
(C) epoxy
Answer: (A)
Exp: The pattern is made of expanded polystrene
11.
A gear train is made up of five spur gears as shown in the figure. Gear 2 is driver and gear
6 is driven member. N2, N3, N4, N5 and N6 represent number of teeth on gears 2, 3, 5 and 6
respectively. The gear(s) which act(s) as idler(s) is/are
N5
N3
N6
N2
2
Driver
6
Driven
N4
(A) only 3
(C) only 5
(B) only 4
(D) Both 3 and 5
Answer: (C)
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
Exp:
www.gateforum.com
NN
2 2 3 5 N3 N5 N6
3 6
6 3 5 6 N2 N4 N5
N2 N4
only Gear(5) is Idle
12.
Let be an arbitrary smooth real valued scalar function and V be an arbitrary smooth
vector valued function in a three-dimensional space. Which one of the following is an
identity?
Cur l V Div V
DivCurlV 0
Div V 0
Div V DivV
Answer: (C)
13.
Answer: (C)
14.
sin x
The value of lim x 0
is ____
2sin x x cos x
Answer: -0.333
Exp:
15.
sin x
lim
x 0 2sin x x cos x
cos x
lim
form
0
L Hospital Rule
Answer: (A)
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
Cp
VCp
Pr
16.
For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are
respectively
V
V
cp
Exp:
www.gateforum.com
MPa
250
200
150
100
50
0
Time
Answer: (C)
Exp:
stress amplitude
Stress ratio
17.
100 Mpa
2
2
min
50
0.2
max 250
Answer: 0.69
x
1
2
y 1hx 0 21h2
Exp:
By Trapezoidal Rule,
2
18.
A weight of 500 N is supported by two metallic ropes as shown in the figure. The values
of tensions T1 and T2 are respectively
30O
T1
90O
T2
120O
500 N
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
www.gateforum.com
Answer: (A)
Exp:
o
o
sin120
sin150
sin 90o
T1
T2
90o
T2 250 N
150o
120o
500
19.
In the notation (a/b/c) : (d/e/f) for summarizing the characteristics of queueing situation,
the letters b and d stand respectively for
(A) service time distribution and queue discipline
(B) number of servers and size of calling source
(C) number of servers and queue discipline
20.
PC
PC
Answer: (B)
Exp:
T-S diagram represent a reversed brayton cycle used in air conditioning of aero planes
where air is used as a refrigerant.
21.
A drill is positioned at point P and its has to proceed to point Q. The coordinates of point
Q in the incremental system of defining position of a point in CNC part program will be
Y
Q
P
12
5
3
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
ME-GATE-2015 PAPER|
(B) (5, 7)
www.gateforum.com
(D) (4, 7)
Answer: (D)
Exp:
22.
A cylindrical tank with closed ends is filled with compressed air at a pressure of 500 kPa.
The inner radius of the tank is 2m, and it has wall thickness of 10 mm. The magnitude of
maximum in-plane shear stress (in MPa) is ____ .
Answer: 25
Exp:
23.
pd
8t
500 4
MPa 25MPa
8 10
T4 T1
T3 T2
T4 T1
T3 T2
Answer: (B)
Exp:
heat applied, Qs cp T3 T2
(B)
T4 T1
T3 T2
(D)
T4 T1
1 T3 T2
heat rejected, Qr cr T4 T1
Qr
1 (T4 T1 )
1
Qs
(T3 T2 )
1
v
24.
Saturated vapor is condensed to saturated liquid in condenser. The heat capacity ratio is
c
Cr min . The effectiveness () of the condenser is
cmax
(A)
1 exp NTU(1 Cr )
1 Cr
NTU
1 NTU
Answer: (D)
(C)
1 exp NTU(1 Cr )
(B)
1 Cr exp NTU(1 Cr )
(D)
1 exp(NTU)
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
10
ME-GATE-2015 PAPER|
Exp:
because Cr
25.
www.gateforum.com
Cmin
0. (as Cmax )
Cmax
For the same material and the mass, which of the following configurations of flywheel
will have maximum mass moment of inertia about the axis of rotation OO passing
through the center of gravity
O'
O'
Answer: (B)
Exp:
Rim med wheel has maximum mass located away from the axis of rotation Thus will have
maximum moment of inertia.
For ball bearings, the fatigue life L measured in number of revolutions and the radial load
F are related by FL1/3 = K, where K is a constant. It withstands a radial load of 2 kN for a
life of 540 million revolutions. The load (in kN) for a life of one million revolutions is
_______
Answer: 16.286
1
Exp:
FL3 k
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
11
ME-GATE-2015 PAPER|
1
www.gateforum.com
F1L31 F2 L32
1
2 540 3 F2 (1) 3
F2 16.286 kN
27.
The torque (in N-m) exerted on the crank shaft of a two stroke engine can be described as
T = 10000 + 1000 sin 1 1200 cos 2, where is the crank angle as measured from
inner dead center position. Assuming the resisting torque to be constant, the power (in
kW) developed by the engine at 100 rpm is __________.
Answer: 104
Exp:
Tmean 10000N m
mean 100
2
60
28.
200
104kW
60
The value of moment o inertia of the section shown in the figure about the ais-XX is
60
30
45
All dimensions
are in mm
X
120
15
X
15
45
30
Answer: (B)
Exp:
Moment of Inertia. I xx
1
1
(120)3 60 2 (30)4 30 30 30
12
12
The value of
3x 8y dx 4y 6xy dy ,
2
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
12
ME-GATE-2015 PAPER|
www.gateforum.com
Answer: 1.66
Exp:
x 0 to x 1 y
&
y 0 to y 1
By Greens theorem,
3x 8y dx 4y 6xy dy
2
x y dxdy
0,1
1 1 y
6y 16y dxdy
x y 1
y 0 x 0
1 y
10ydx dy
y 0
x 0
1
10
yx
1 y
0
0,0
1,0
dy
y 0
y 2 y3
10 y 1 y 0 dy 10
3
2
y 0
1
1 1 5
10 1.66
3 3 3
30.
cold ambient air. On a particular winter day, the outside air temperature is 5C and the
room needs to be maintained at 27C. The heat transfer coefficient associated with
W
outside air is 20 2
. Neglecting the convective resistance of the air inside the room,
m K'
w
the heat loss, in 2 is
m
(A) 88
Answer: (C)
(B) 110
(C) 128
(D) 160
Exp:
5o C
27o C
h 20w / m 2 K
1
1
1
l
R th
h k
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
13
ME-GATE-2015 PAPER|
www.gateforum.com
1
1
4 W / m2 K
1 0.18
R th
20 0.9
Q
31.
T
27 (5) 4 128 W / m 2
R th
A bullet spins as the shot is fired from a gun. For this purpose, two helical slots as shown
in the figure are cut in the barrel. Projections A and B on the bullet engage in each of the
slots
Gun Barrel
A
Bullet
0.5m
Helical slots are such that one turn of helix is completed over a distance of 0.5 m. If
velocity of bullet when it exits the barrel is 20 m/s, its spinning speed in rad/s is _______.
Answer: 251.3
Exp:
0.5
0.025 sec.
20
2
rad / sec
0.02s
32.
Which of the following statements are TRUE, when the cavitation parameter = 0?
i. the local pressure is reduced to vapor pressure
ii. cavitation starts
iii. boiling of liquid starts
iv cavitation stops
(A) i, ii and iv
Answer: (D)
Exp: = 0 implies (i), (ii) and (iii)
33.
In a CNC milling operation, the tool has to machine the circular arc from point (20, 20) to
(10, 10) at sequence number 5 of the CNC part program. If the center of the arc is at (20,
10) and the machine has incremental mode of defining position coordinates, the correct
tool path command is (A) N 05 G 90 G01 X10 Y10 R10
(B) N 05 G91 G03 X10 Y10 R10
(C) N 05 G90 G03 X20 Y20 R10
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
14
ME-GATE-2015 PAPER|
www.gateforum.com
for incremental coordinates (G91) and coordinates of final point are (10, 10). The tool
moves CCW (counter clockwise), So G03.
34.
Answer:
Exp:
0.5625
V
ts k
A
2
2
d h
d
t1 k 4
k d h
4
dh
2
2
a3
a
d
t 2 k 2 k k a 2d
6
3
6a
2
d
2
t1 4 3
0.5625
t 2 d 2 4
3
35.
(A) -3
(B) -0
(C) 1
(D) 2
Answer: (C)
Exp: Number of links, N = 6
Total number as binary joints, j = 7
F = 3 (N-1) 2j
= 15-14 = 1.
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
15
ME-GATE-2015 PAPER|
36.
www.gateforum.com
Figure shows a single degree of freedom system. The system consists of a massless rigid
bar OP hinged at O and a mass m at end P. The natural frequency of vibration of the
system i
fn
1
k
2 4m
1 k
C fn
2 m
fn
1
k
2 2m
k
Q
1 2k
D fn
2 m
P
m
Answer: (A)
Exp:
x
x1 2a 2x
a
fn
37.
2mg 4mg
2
k
k
wn
X
X1
g
g
k
;
s
x1
4m
1
1
k
n
2
2 4m
Answer: (A)
Exp:
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
16
ME-GATE-2015 PAPER|
www.gateforum.com
x2
(0,4)
(20,0)
x1
(45,0)
38.
Air in a room is at 35 and 60% relative humidity (RH). The pressure in the room is 0.1
MPa. The saturation pressure of water at 35C is 5.63 kPa. The humidity ratio of the air
(in gram/kg of dry air) is _____.
Answer: 21.74
Exp:
Pw
P
0.6 w
Ps
5.63
Pw 3.378KPa
Pw
Pa Pw
3.378
100 3.378
0.021745kg kg of dry air
0.622
39.
2r
2
1
8r
1
12
1
2
D 12
Answer: (A)
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
17
ME-GATE-2015 PAPER|
Exp:
www.gateforum.com
f11 f12 1
f12 1
f 21 A 2 f12 A1
f 21
f12 A1
1 4r 2
1
1
2
2
A2
4 4r 4r 12
2
Exp:
By Newton-Raphson Method,
1st iteration, x1 x 0
1
f x0
f x0
f 1
5 1
1
f 1
10 2
Where f x x 3 2x 2 3x 1 f 1 5
f x 3x 2 4x 3 f 1 10
2nd iteration, x 2 x1
f x1
f x1
0.5
f 0.5
0.3043
f 0.5
41.
The annual requirement of rivets at a ship manufacturing company is 2000 kg. The rivets
are supplied in units of 1 kg costing Rs. 25 each. If the costs Rs. 100 to place an order and
the annual cost of carrying one unit is 9% of its purchase cost, the cycle length of the
order (in days) will be_____
Answer: 76.94
Exp:
EOQ
2DC0
Ch
2 2000 100
421.637
0.09 25
length of cycle
365
76.948 days
No. of orders
No. of orders
2000
EOQ
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
18
ME-GATE-2015 PAPER|
42.
www.gateforum.com
f t e
st
dt.
1 e2s
s
1 2es
D
s
Answer: (C)
Exp:
1 es
2s
2 2es
s
f t 2; 0 t 1
0; otherwise
est
L f t 2e dt 2
s
0
1
43.
2 2es
s
Orthogonal turning of a mild steel tube with a tool of rake angle 10 carried out at a feed
of 0.14 mm/rev. If the thickness of the chip produced is 0.28 mm, the values of shear
angle and shear strain will be respectively
(A) 2820 and 2.19
Answer:
Exp:
st
(A)
0.14
0.5
0.28
r cos
1 r sin
28.3345o
tan
or 28o 20
44.
Steam enters a turbine at 30 bar, 300C (u = 2750 kJ/kg, h = 2993 kJ/kg) and exits the
turbine as saturated liquid at 15 kPa (u = 225 kJ/kg, h = 226 kJ/kg). Heat loss to the
surrounding is 50 kJ/kg of steam flowing through the turbine. Neglecting changes in
kinetic energy and potential energy, the work output of the turbine (in kJ/kg of steam) is
_______.
Answer: 2717
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
19
ME-GATE-2015 PAPER|
www.gateforum.com
Exp:
45.
i
4 3i
For a given matrix
, where is i 1, the inverse of matrix P is
4 3i
i
i
1 4 3i
4 3i
24 i
1
25
4 3i
i
4 3i
i
i
1 4 3i
4 3i
24 i
i
1 4 3i
4 3i
25 i
Answer: (A)
Exp: |P| = (4+3i)(4-3i)-(i)(-i) = 16+9-1 = 24
i
4 3i
adjP
4 3i
i
i
1 4 3i
P 1
4 3i
24 i
46.
For the overhanging beam shown in figure, the magnitude of maximum bending moment
(in kN-m) is _____.
20kN
10kN m
B
2m
4m
Answer: 40 kN-m
Exp:
BMD:
5
M
(KN m) A
C
X
R A 10kN
40
R B 50kN
Maximum bending momentum occurs at reaction B an has a magnitude of 40 kN-m.
47.
Figure shows a wheel rotating about O2. Two points A and B located along the radius of
wheel have speeds of 80 m/s and 140 m/s respectively. The distance between the points A
and B is 300 mm. The diameter of the wheel (in mm) is ________
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
20
ME-GATE-2015 PAPER|
www.gateforum.com
Answer: 1400
Exp:
VA 80 m / s, VB 140 m / s
rB rA 300
(i)
rA 80
O2
rB 140
rB
1.75
rA
...(2)
48.
1.0 0.70
10
12
0.55
0.50
0.40
0.35
Answer: 10.61
Exp:
Shapefactor
l w 25 15
Vr
0.5
Vc
Vr 0.5 25 15 5 937.5
3
d 937.5cm3
4
d 10.61cm
49.
A Prandtl tube (Pitot-static tube with C = 1) is used to measure the velocity of water. The
differential manometer reading is 10 mm of liquid column with a relative density of 10.
Assuming g = 9.8 m/s2, the velocity of water (in m/s) is _______.
Answer:
Exp:
1.32
sg
h x 1 0.0110 1 0.09m
s0
velocityof flow 2 9.8 0.09 1.328m s
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
21
ME-GATE-2015 PAPER|
50.
www.gateforum.com
Answer: 0.1414
Exp:
h max
h max
R
25 20 5mm
R 250 mm
51.
5
0.1414
250
Refrigerant vapor enters into the compressor of a standard vapor compression cycle at
10C (h = 402 kJ/kg) and leaves the compression at 50C(h = 432 kJ/kg). It leaves the
condenser at 30C (h = 237 kJ/kg). The COP of the cycle is __________.
Answer: 5.5
Exp:
52.
165
5.5
30
A cantilever bracket is bolted to a column using three M12 1.75 bolts, P, Q and R. The
value of maximum shear stress developed in the bolt P (in MPa) is _______.
9kN
40
30
30
40
P
Q
10mm thick
250
are in mm
Answer: 341
Exp:
All dimension
P=9kN, e=250 mm
P
Pp''
p q
3kN
3 3
Pp'
q
C.G
Pq'
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
22
ME-GATE-2015 PAPER|
www.gateforum.com
rp 30 mm
rr 30 mm
rq 0
Pr''
Pe
9000 250
2 2
1250
2
2
r rq rr 30 0 302
2
q
Pr'
Pp'' Pr'' C
Pp'' Crp 37.5 kN
Pr' Crr 37.5 kN
Pq'' 0
53.
P
38.5648
O2
CO2
Rm
54.
100
30.233 kg / kmol
60 30 10
28 32 44
8314
274.996J / kg K
30.233
A shaft of length 90 mm has a tapered portion of length 55 mm. The diameter of the taper is
80 mm at one end and 65 mm at the other. If the taper is made by tailstock set over method,
the taper angle and the set over respectively are
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
23
ME-GATE-2015 PAPER|
www.gateforum.com
Answer: (A)
Exp:
Rate of taper, T
Set over=
80 65
0.27
55
T L 0.27 90
12.15
2
2
55.
One side of a wall is maintained at 400 K and the other at 300 K. The rate of heat transfer
through the wall is 1000 W and the surrounding temperature is 25C. Assuming no
generation of heat within the wall, the irreversibility (in W) due to heat transfer through the
wall is ________.
Answer:
248.33
Exp:
Q = 1000W
T 25 273 298
T
T
Q 1 Q 1 Qir 0
T1
T2
298
298
1000 1
1000 1
Qir 0
400
300
Qir 248.33W
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized
in any form without the written permission. Discuss this questions paper at www.gatementor.com.
24