Documente Academic
Documente Profesional
Documente Cultură
TABLE OF CONTENTS
Page
Safety Precautions........................................................................................................ ii
1. Important Notice.......................................................................................................... 1
2. Introduction.................................................................................................................. 1
5. Installation.................................................................................................................... 2
7. Troubleshooting Guide............................................................................................. 4
8. Replacement Parts...................................................................................................4-11
SAFETY PRECAUTIONS
We have provided many important safety messages in this manual on your XA Series Extraction arms.
Always read and obey all safety messages.
DANGER
WARNING
C A U TI O N
This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the
safety alert symbol and the word DANGER WARNING or CAUTION. These words mean:
C A U TI O N
Indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury.
CAUTION used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
IMPORTANTSAFETYINSTRUCTIONS
WARNING
To reduce the risk of fire, electric shock, or injury when using your air cleaner, follow these basic precautions:
U
se this product within the manner intended by the
manufacturer. If you have questions contact the
manufacturer.
W
ear appropriate dust mask, eye protection and
protective clothing while servicing this equipment.
R
ead and understand the Owners Manual prior to
installing, operating or servicing this equipment
U
se proper lifting and rigging equipment to install this
equipment.
ii
XA Series
Source Capture Extraction Arms
Revised 04/13
1. IMPORTANT NOTICE
2. INTRODUCTION
XA -
XX
XA Series
Source Capture Extraction Arms
Revised 04/13
WARNING
4. Product Specifications
Arm
Diameter
in (mm)
Nominal Shipping
Length
Weight
Model
ft (m)
lb (kg)
XA-607
7 (2)
50 (23)
6.3 (160)
XA-610
10 (3)
52 (24)
XA-612
12 (3.6)
55 (25)
30 (14)
XA-6T
4 (5.5)
35 (16)
4 (5.5)
XA-8T
XA-807
7 (2)
90 (41)
8 (200)
XA-810
10 (3)
92 (42)
XA-812
12 (3.6)
95 (43)
Table 1 - Extraction Arm Product Matrix
5. INSTALLATION
5.1 E
quipment Off-Loading and
Inspection
5.3 W
all Mount Arm Assembly
INSTRUCTIONS
XA Series
Source Capture Extraction Arms
Revised 04/13
5. Ensure to place the thin bearing piece above the arm
base assembly and against the bottom surface of the
wall mount bracket.
6. Lift arm, orient as shown, and align the holes through
all of the pieces. Secure with the mounting hardware
provided. The arm is not fully supported at this point
so ensure to continue to support arm such that it
does not fall on personnel or equipment in the area.
7. Locate the spring and spring mounting pins in loose
parts kit box. Some arms will have an extension rod
as well. The mounting pins should be taped to the
lid of the box. Ensure that the pin and snap rings are
within reach for installation.
8. Install the spring in orientation shown onto the base
assembly spring bracket. Install spring pin and
retainer to secure the spring to the base assembly
spring bracket.
9. Lift the arm and align the spring with the base tube
spring bracket. Install spring pin and retainer to
secure the spring to the base tube spring bracket.
10. At this point check the arm for proper motion. The
arm should rotate on the base freely. The torques
at each joint are preset to hold the arm in position
throughout the full range of motion. The arm
movement can be adjusted as necessary to better fit
your process. Refer to section 6.1 to properly adjust
the relevant joints on the arm.
11. Install the flex duct onto the base and middle joints
using the split clamps provided. The middle and base
joints utilize the 24 and 30 pieces respectively.
7. At this point check the arm for proper motion. The
arm should rotate on the base freely. The torques
at each joint are preset to hold the arm in position
throughout the full range of motion. The arm
movement can be adjusted as necessary to better fit
your process. Refer to section 6.1 to properly adjust
the relevant joints on the arm.
WARNING
XA Series
Source Capture Extraction Arms
Revised 04/13
Model
XA-607-PM
XA-610-PM
XA-612-PM
XA-607-WM
XA-610-WM
XA-612-WM
XA-6T
XA-8T
XA-807-PM
XA-810-PM
XA-812-PM
XA-807-WM
XA-810-WM
XA-812-WM
6.3 (160)
6.3 (160)
8 (200)
8 (200)
ft (m)
7 (2)
10 (3)
12 (3.6)
7 (2)
10 (3)
12 (3.6)
5 (5.5)
4 (5.5)
7 (2)
10 (3)
12 (3.6)
7 (2)
10 (3)
12 (3.6)
ft-lbs. (Nm)
2.0 (2.7)
2.0 (2.7)
2.0 (2.7)
2.0 (2.7)
2.0 (2.7)
2.0 (2.7)
N/A
N/A
2.0 (2.7)
3.0 (4.1)
6.0 (8.1)
3.0 (4.1)
3.0 (4.1)
6.0 (8.1)
ft-lbs. (Nm)
3.0 (4.1)
3.5 (4.7)
3.0 (4.1)
3.5 (4.7)
3.5 (4.7)
3.5 (4.7)
7.0 (9.5)
3.0 (4.1)
6.0 (8.1)
7.0 (9.5)
2 - Adjustable
Elbow Factory Recommended
Torque
Settings
Table 2Table
- Factory
Recommended
Elbow Joint
Torque
Settings
7. TROUBLESHOOTING GUIDE
WARNING
POSSIBLE CAUSES
RECOMMENDED SOLUTIONS
Inspect, clean, and re-lubricate the tube O-rings on the telescopic tube
assembly. Too much silicone lubricant can cause the assembly to slip.
Wipe excess oil off of O-rings and tube prior to re-assembly.
Inspect and remove any debris which may be lodged within the arm.
8. REPLACEMENT PARTS
WARNING
CAUTION
Ensure to refer to the correct table and figure for your fume extraction
swing arm when selecting the appropriate replacement parts.
Using incorrect components for your arm could cause damage to the
equipment and possible injury to the operator.
XA Series
Source Capture Extraction Arms
Revised 04/13
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
DESCRIPTION
BASE ASSEMBLY
BASE TUBE ASM
HOOD TUBE ASM
GAS SPRING
BASE FLEX DUCT
MID FLEX DUCT
HOOD FLEX DUCT
HOSE CLAMP
HOOD ASSEMBLY
THICK BEARING
SPRING PIN KIT
BASE MTG HDWR
XA-607-PM
XA-610-PM
XA-612-PM
02-10812-6
02-11099
02-11100
02-11103
02-11104
02-10922
36-10003-0140
36-10003-0175
15-10048-630
15-10048-624
15-10048-612
15-0004
02-10817-6
10-12674-6
03-10561-02
03-10561-01
XA-807-PM
XA-810-PM
XA-812-PM
02-10812-8
02-11105
02-11106
02-11109
02-11110
02-10922
36-10003-0140
36-10003-0175
15-10048-830
15-10048-824
15-10048-812
15-0005
02-10817-8
10-12674-8
03-10561-02
03-10561-01
*Basemountinghardwarekitnotshown
FIGURE 1
Portable Mount Arm
Detail and Replacement Parts
FIGURE1
PortableMountArmDetailandReplacementParts
XA Series
Source Capture Extraction Arms
Revised 04/13
ITEM
DESCRIPTION
1
2
3
4
4a
5
6
7
8
9
10
11
12
BASE ASSEMBLY
BASE TUBE ASM
HOOD TUBE ASM
TENSION SPRING
EXTENSION ROD
BASE FLEX DUCT
MID FLEX DUCT
HOOD FLEX DUCT
HOSE CLAMP
HOOD ASSEMBLY
THIN BEARING
SPRING PIN KIT
BASE MTG HDWR
XA-607-WM
XA-610-WM
XA-612-WM
02-10812-6-WM
02-11101
02-11102
02-11103
02-11104
36-10006
36-10007
36-10007
N/A
10-12912
10-12912
15-10048-630
15-10048-624
15-10048-612
15-0004
02-10817-6
10-12673-6
03-10561-02
03-10561-07
XA-807-WM
XA-810-WM
XA-812-WM
02-10812-8-WM
02-11107
02-11108
02-11109
02-11110
36-10006
02-10946-10
02-10946-12
N/A
N/A
N/A
15-10048-830
15-10048-824
15-10048-812
15-0005
02-10817-8
10-12673-8
03-10561-02
03-10561-07
*Basemountinghardwarekitnotshown
FIGURE2
WallMountArmDetailandReplacementParts
FIGURE 2
Wall Mount Arm Detail and Replacement Parts
XA Series
Source Capture Extraction Arms
Revised 04/13
Item #
1a
1b
2
3
4
5
6
7
8
9
Part #
02-10911-6
02-10911-8
30-10099
30-10096-0250
30-10095-0250
30-10131
30-0094
30-10130
30-10128
10-12682
Description
INLET SCREEN (6" ARMS)
INLET SCREEN (8" ARMS)
1/4"-20 BOLT
1/4" FLAT WASHER
1/4" LOCK WASHER
5/16"-18 CARRIAGE BOLT
3/8" FLAT SPACER WASHER
5/16"-18 FLANGED NYLON LOCK NUT
5/16" PLASTIC FRICTION WASHER
HOOD KNUCKLE
FIGURE3
TypicalHoodDetailandReplacementParts
FIGURE 3
Typical Hood Detail and Replacement Parts
XA Series
Source Capture Extraction Arms
Revised 04/13
Item #
1a
1b
2a
2b
3a
3b
4a
4b
5
6
7
8
9
10
11
12
13
14
Part #
10-12689-2M
10-12689-4M
10-12688-2M
10-12688-4M
10-12688-1M
10-12688-3M
10-12689-1M
10-12689-3M
30-10035-0003
30-10096-0375
30-10095-0375
30-10097-0375
30-10132
10-12681
30-10092
30-10096-0500
30-10097-0500
30-10098-0500
Description
OUTSIDE LEFT ELBOW (6" ARMS)
OUTSIDE LEFT ELBOW (8" ARMS)
OUTSIDE RIGHT ELBOW (6" ARMS)
OUTSIDE RIGHT ELBOW (8" ARMS)
INSIDE LEFT ELBOW (6" ARMS)
INSIDE LEFT ELBOW (8" ARMS)
INSIDE RIGHT ELBOW (6" ARMS)
INSIDE RIGHT ELBOW (8" ARMS)
3/8"-16 CARRIAGE BOLT
3/8" FLAT WASHER
3/8" LOCK WASHER
3/8"-16 NUT
1/2"-13 CARRIAGE BOLT
FRICTION DISC
SLIP WASHER
1/2" FLAT WASHER
1/2"-13 NUT
1/2"-13 JAM NUT
FIGURE 4
FIGURE4
Typical Elbow Joint Detail
and Replacement Parts
TypicalElbowJointDetailandReplacementParts
XA Series
Source Capture Extraction Arms
Revised 04/13
1
2
3
4
5
6
7
8
9
BASE ASSEMBLY
THIN BEARING
THICK BEARING
ROLLED BASE
CAPTURE BASE
BACKING PLATE
SPRING MOUNT*
1/4-20 BOLT
1/4" LOCK WASHER
1/4-20 NUT
FIGURE 5
Base Assembly Detail and Replacement Parts
Revised 04/13
!"#$
!
+
<
;
=
A
1
0
!*
!!
!+
Figure 5
10
XA Series
Source Capture Extraction Arms
%#&'(!)"!*+
,-./"
,-.0"
"#$%&#$$%'"()
*+,!!!-+
*+,!!!-!
"#$%&./"%&#$$%'"()
*+,!!!+0
*+,!!!+1
2(%3&4/5.6&-*7&(89:
!;,!**<1,=-*
!;,!**<1,1-*
>8$%&5(#'?
!;,***<
!;,***;
.%(%$58?@5&./"@9:&#$$%'"()
*+,!!!++
>884&#$$%'"()
*+,!*1!A,=
*+,!*1!A,1
/,"8(.&B@.>&9/.$
-*,!*!<*
@9(%.&$5C%%9
*+,!*0!!,=
*+,!*0!!,1
!D<7,+*&"8(.
-*,!**00
!D<7&2(#.&B#$>%C
-*,!**0=,*+;*
!D<7&(85E&B#$>%C
-*,!**0;,*+;*
;D!=7,!1&5#CC@#:%&"8(.
-*,!*!-!
Figure 6
Figure 7 FIGURE 6
Telescopic Wall Mount Arm Detail and Replacement Parts
XA Series
Source Capture Extraction Arms
Revised 04/13
FIGURE 7
Telescopic Mechanism and Replacement Parts
11