Documente Academic
Documente Profesional
Documente Cultură
698894 MHz
90
12
0
21
0
21
30
60
20
30
30
90
12
24
180
15
180
Horizontal pattern
45- polarization
90
270
21
12
3
10
30
20
21
30
30
10
15
11400-C
936.4267
180
Vertical pattern
45- polarization
010 electrical downtilt
33
15
33
24
698806 MHz
15.3 dBi
>30 dB (co-polar)
34 dB (average)
500 watts (at 50C)
12
24
17102170 MHz
IRT specifications:
Gain
Front-to-back ratio
90
15
180
270
Specifications:
270
Horizontal pattern
45- polarization
Frequency range
698894 MHz // 17102170 MHz
Impedance
50 ohms
VSWR
<1.5:1
Intermodulation (2x20w)
IM3:< -150 dBc
Polarization
+45 and -45
Connector
4 x 7-16 DIN female (long neck)
Isolation
intrasystem >30 dB // intersystem >35 dB
See reverse for order information.
60
20
30
24
3GPP/AISG 2.0
AISG 1.1 and 3GPP/AISG 2.0 compliant
2 x 8pin connector acc. IEC 60130-9;
according to AISG:
RCUin (male): Control / Daisy chain in
RCUout (female): Daisy chain out
1030 V
<1 W (standby); <8.5 W (motor activated)
40 seconds
>50,000
FCC 15.107 Class B Computing Devices
60
20
270
30
30
General specifications:
3
10
10
30
30
33
33
30
Vertical pattern
45- polarization
010 electrical downtilt
1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG
1.1 and vice versa with a vendor specific command. Start-up operation of the
RCU 86010149 is possible in an RET system supporting AISG 1.1 or supporting
3GPP/AISG 2.0 after performing a layer 2 reset before address assignment. The
protocol can also be changed as follows: AISG 1.1 to 3GPP: Enter "3GPP" into
the additional data filed "Installers ID" and perform a layer 7 reset or a power
reset. 3GPP to AISG 1.1: Enter "AISG 1" into the additional datafield "Installers
ID" and perform a layer 2 reset or a power reset. After switching the protocol any
other information can be entered into the "Installers ID" field.
2)
The tightning torque for fixing the connector must be 0.5 1.0 Nm (hand-tightened).
The connector should be tightened by hand only!
824894 MHz
15.8 dBi
>30 dB (co-polar)
34 dB (average)
500 watts (at 50C)
17101755 MHz
18 dBi
>27 dB (co-polar)
34 dB (average)
300 watts (at 50C)
18501990 MHz
18.5 dBi
>27 dB (co-polar)
34 dB (average)
300 watts (at 50C)
21102170 MHz
18 dBi
>27 dB (co-polar)
34 dB (average)
300 watts (at 50C)
65 (half-power)
63 (half-power)
62 (half-power)
63 (half-power)
10.8 (half-power)
5.8 (half-power)
5.8 (half-power)
5.8 (half-power)
010
010
010
010
0
5 10 T
18 18 16 dB
20 22 20 dB
0 5 10 T
18 18 18 dB
20 22 20 dB
0 5 10 T
18 18 18 dB
20 22 20 dB
0 5 10 T
18 18 18 dB
20 22 20 dB
20 dB (typical)
>10 dB, 14 dB (avg)
1.5 db
3
25 dB (typical)
>8 dB, 15 dB (avg)
1.5 db
3
30 dB (typical)
>10 dB, 15 dB (avg)
1.0 db
2.5
25 dB (typical)
>8 dB, 15 dB (avg)
1.5 db
3
Sep 1, 2012
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500
Email: communications@kathrein.com Internet: www.kathrein-scala.com
800 10765V01
Dual Band Broadband 6', 65 Degree Antenna
RET
Mechanical specifications:
Weight
Dimensions
Wind load
Front/Side/Rear
Mounting category
Wind survival rating
Shipping dimensions
Shipping weight
Mounting
64 mm
M8
Mounting Brackets
KATHREIN
78.3 inches
(1989 mm)
76.7 inches
(1948 mm)
860 10149
75.5 inches
(1918 mm)
Tested To Comply
With FCC Standards
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
11.8 inches
(300 mm)
out
in
698894
45
IRT
698894
+45
17102170 17102170
45
+45
8pin male
8pin female
Order Information:
Model
800 10765V01
800 10765V01 K
Description
Dualband antenna with mounting bracket
010 // 010 electrical downtilt
Dualband antenna with
mounting bracket and mechanical tilt bracket
010 // 010 electrical downtilt
in
out
8pin female
8pin male
All specifications are subject to change without notice. The latest specications are available at www.kathrein-scala.com.
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500
Email: communications@kathrein.com Internet: www.kathrein-scala.com