Documente Academic
Documente Profesional
Documente Cultură
STI REPEATER
Model: STI-34109
Thank you for purchasing this fine product. Your satisfaction is very important to us. Please read this manual
carefully to get the most from your new product.
STI offers wireless products designed to alert you of several different conditions. The STI REPEATER is a 433
MHz radio signal receiver and transmitter that effectively doubles the transmission range of STI sensors to STI
receivers. The REPEATER will filter out all radio signals that are not using 433 MHz STI protocol. When any STI
protocol signal packet (except STI 8-Channel Receiver) is received, it transmits the same signal packet. There is
no limit to the number of STI sensors that may be used with the STI REPEATER.
It should be understood that multiple REPEATERS should NOT be used within reception range of each other
because a REPEATER will simply retransmit any STI protocol signal packet (except 8-Channel Receiver). Two
REPEATERS within reception range of each other can retransmit signal packets back and forth a few times when
sensor packet is received.
If a dual REPEATER system or further extended range applications are needed, please purchase STI 8-Channel
Receivers (STI-34108). The receivers will retransmit alert and trouble notifications of the sensor signals, but not
the actual signals themselves. Therefore, REPEATER feedback will not occur. The receivers work with up to 8
different STI wireless sensors.
FEATURES
SPECIFICATIONS
OPERATION
The REPEATER receives distant STI protocol sensor signals and repeats the information to the receiver.
Generally, STI sensors send 8 identical signal packets of information. The REPEATER rejects any signal that is
not an STI protocol packet and retransmits the complete 8 packet set to the receiver.
The receiver can monitor the REPEATERS supervision and trouble signals when they are enrolled (if desired).
To manually send a REPEATER signal, press and release the tamper switch. Ensure the red LED blinks.
To enroll sensors, follow the receivers programming instructions.
LEDS
ON BLINKING
GREEN LED
AC/DC power on
Signal Received
RED LED
Signal Transmitted
INSTALLATION GUIDE
1. Press the cover latch to remove top cover (do not lose tamper switch spring).
2. Remove the PCB from bottom cover.
Using the keyholes on the bottom cover as a template, mark the top and bottom mounting holes. Locate the
hole at least 1 foot away from the closest obstruction above.
3. Drill 3/16 holes.
4. Insert wall anchors, screws and washers (provided) and tighten to 1/8 gap.
5. TURN OFF POWER SUPPLY. Route power supply wires from the side (recommended) or hole from the back.
a. Side installation route wires through right wire guide and then left wire guide. Remove knockout on the
top cover.
b. Rear installation run wires through back wire guide and then left wire guide.
6. Place bottom cover keyholes onto screws and orient device vertical.
7. Tighten screws.
8. On the PCB, insert the antennas into the outer antenna terminals marked ANTENNA. Tighten the antenna
terminal screws.
9. Snap PCB into bottom cover so the antennas are on the plastic stands.
10. Remove the battery tab. The red LED blinks when the batteries are installed. If LED does not blink, press
and release the tamper switch. If LED still does not blink, replace batteries.
11 .Insert 12 Volt AC or DC power supply leads into the terminals marked AC/DC 12V. The positive and
negative terminals have interchangeable polarity. They may be oriented either +/- or -/+.
12. Turn on the power supply. The green LED turns on. If the red LED is on, replace the 3 AAA Alkaline
batteries.
13. (If desired) Program the REPEATER and/or the sensors into the receiver (follow the receiver programming
instructions). The receiver can monitor the REPEATERS supervision and trouble signals when enrolled.
To manually send a REPEATER signal, press and release the tamper switch. The red LED blinks when
transmitting.
14. If the REPEATER or the sensors do not program properly, move the REPEATER mounting location closer to the
receiver.
15. Latch the top cover in place. Ensure the power supply wires are routed properly.
IMPORTANT NOTICE
WARNINGS
FOR INDOOR USE ONLY. Keep away from water or damp areas.
WARRANTY INFORMATION
Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free
of defects in material and workmanship under normal use and circumstances for a period of one (1) year from
the original date of purchase.
Electronic warranty form at www.sti-usa.com/wc14.
APPLICATIONS GUIDE
Circle = sensor
For out of range sensor(s), position REPEATER between sensor and receiver.
If some sensors are in range of the receiver, mount the REPEATER closer to the out of range sensor. The
REPEATER should not receive the in range sensor packets.
If it is not possible for the REPEATER to receive out of range sensors without also picking up in range sensor
packets:
Move the receiver location forcing in range sensors out of range.
Purchase an STI 8-Channel Receiver to mirror the out of range packets to the original 8-Channel Receiver.
Continue to use the receiver as it is, allowing duplicate sensor packets to be received. This should not
change the receiver operation.
Reconfigure system.
Single Repeater System - General Use
Multiple Sensor/Re
Out of range
sensor
Up to
1000 ft.
Up to
1000 ft.
Up to 1000 ft.
to farthest sensor
1 - MIRROR MASTER OFF/ON
2 - NORMAL/ENROLL
3 - AUTO RESTORE/LATCH
4 - SIREN TIME/MIRROR#
5 - SIREN TIME/MIRROR#
6 - CHIME OFF/ON
7 - NORMAL/DELETE
8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
In range
sensor
Repea
Receiver
Repeater
Figure 1
Extended Range System
The REPEATER will receive and transmit any STI protocol signal packets received (except 8-Channel Receiver).
Multiple sensors can be arranged to pass packets through the REPEATER to multiple receivers.
Up to
1000 ft.
Up to
1000 ft.
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Up to
1000 ft.
Up to
1000 ft. to
farthest sensor
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
Receiver
Multiple Sensor/Receiver
System(Mirrored)
(Master)
Repeater
Up to
1000 ft.
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
In range
sensor
System Range
(Up to 6000 ft. span - with a full mirrored system
Receiver #1
Up to
Up to 1000 ft.
1000 ft.
to farthest sensor
SW5
SIREN
TIME
MIRROR #
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Repeater
Up to
8 sensors
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
Up to
Repeater
Receiver
ange System
SW4
OFF
ON
OFF
ON
Up to
1000 ft.
Sensor
8 sensors
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver #2
Up to
1000 ft. to
Receiver
Repeater
The REPEATER may be used to extend the range of sensors to a multiple STI 8-Channel Receiver mirroring
system.
Extended Range System
Up to
1000 ft.
Up to
1000 ft.
Up to
1000 ft.
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Up to
1000 ft. to
farthest sensor
Receiver
(Master)
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
(Mirrored)
Up to
1000 ft.
Repeater
12345678-
Re
Repeater
Keep Repeat
from e
System Range
(Up to 6000 ft. span - with a full mirrored system
Figure 3
Up to
8 sensors
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver #1
System
- General
Use
Multiple
Sensor/Receiver
System
Central
Monitoring
of Multiple
Locations
(Figures
5)
Up4
to and
1000 ft.Sensor
Up to
1000 ft.
to farthest sensor
Up to
8 sensors
Repeater
Up to
Keep Repeater1000
out offt.range
Out
range
fromofnon-repeater
sensor
sensor
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
sensor
Receiver
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver #1
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
System
with Multiple Locations Monitored
Receiver #2 Centrally
UpSTI
to protocol packets received (except
Repeater Because REPEATERS
Up towill
1000retransmit
ft.
REPEATER Feedback
any
1000 ft.
to farthest sensor
Up to 8-Channel Receiver), if two REPEATERS are within reception range of each other they will send packets back
1000 ft.
Up toKeep out of range
In range
and forth to each
other. When using more than one REPEATER,
keep
them out 8ofsensors
range from each other. An Up to
Repeater
sensor
Up to
1000 ft. to
1000 ft. to
Receiver
STI 8-Channel
Receiver can be substituted for a REPEATER to farthest
eliminate
sensor this problem.
farthest sensor
Up
to
Up to
Receiver #2
Extended
Range System
System
with
Distance
between
2 ft.
Locations
ft. the same
1000
Dual REPEATER
Reception
If more than one REPEATER receives
a signal
packet1000
from
sensor, both
Repeater
Repeater
REPEATERS will retransmit the packet. This should not be an issue, but the programmed receiver will then
Keep out of range
Keep out of range
respond to both transmissions.
1 - MIRROR MASTER OFF/ON
2 - NORMAL/ENROLL
3 - AUTO RESTORE/LATCH
4 - SIREN TIME/MIRROR#
5 - SIREN TIME/MIRROR#
6 - CHIME OFF/ON
7 - NORMAL/DELETE
8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Up to
1000 ft.
1000 ft.
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
1000 ft.
SW5
SIREN
TIME
MIRROR #
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
(Mirrored)
Up to
1000 ft. to
Up to
farthest sensor
System Range
1000 ft.
(Up to 6000 ft. span - with a full mirrored system
SW5
SIREN
TIME
MIRROR #
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
1
2
3
4
Repeater
Up to
1000 ft.
SW4
MIRROR #
DISABLED
30 SEC
180 SEC
ON CONT
SW4
OFF
ON
OFF
ON
Receiver
(Master)
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
(Mirrored)
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
SW5
SIREN
TIME
MIRROR #
SW4
SW5
SIREN
TIME
MIRROR #
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
Repeater
Sensor
from each other
tem Range
- with a full mirrored system
Figure 4
Sensor
Up to
System with Multiple Locations Monitored Centrally
Up to
1000 ft.
1000 ft.
Up to
1000 ft. to
farthest sensor
Repeater
Repeater
Keep out of range
Keep out of range
If 2 repeaters receive a
Up to signal from the
Upsame
to
1000 ft. sensor, the signal
1000will
ft. be
sent to the receiver 2 times.
Repeater
Up to
1000 ft. to
farthest sensor
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
Up to
1000 ft. to
farthest sensor
Up to
1000 ft.
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
Up to
1000 ft.
Repeater
Up to
1000 ft. to
farthest sensor
Repeater
Up to
1000 ft. to
farthest sensor
SW4
SW5
SIREN
TIME
MIRROR #
OFF
ON
OFF
ON
OFF
OFF
ON
ON
DISABLED
30 SEC
180 SEC
ON CONT
1
2
3
4
Receiver
Up to
1000 ft.
Up to
1000 ft.
Repeater
Figure 5
Up to
1000 ft. to
farthest sensor
Repeater
Up to
1000 ft.
Receiver
Receiver
SW4
OFF
ON
OFF
ON
Repeater
Receiver
Repeater
Up to
1000 ft. to
farthest sensor
Repeater
Up to
1000 ft. to
farthest sensor
Repeater
Up to
Up to
Up to
1000 ft. to Up to
1000 ft.
sensor
Up farthest
to
1000 Keep
ft. to Repeater
out of range1000 ft.
1000 ft.
farthest sensor
from each
other
Keep out of range
Repeater
OFF
ON
OFF
ON
SIREN
TIME
OFF
OFF
ON
ON
signal from
theft.
Up to
1000
toLocations
System
2same
sensor, the signal
will be
Up to with Distance between
1000 ft.
farthest sensor
Receiver
(Master)
SW5
If 2 repeaters
a
Upreceive
to
Range System
Up to
p to
0 ft.
SW4
OFF
ON
OFF
ON
Up to
1000 ft. to
farthest senso
Repeater