Documente Academic
Documente Profesional
Documente Cultură
A. 1.52o
B. 1.02o
C. 1.44o
D. 1.32o
A. 1.0 psi
B. 10 psi
C. 67 psi
D. 2.0 psi
40. A long beam of length L has a
formula which is 48Ely = w
(2x^4 5Lx^3 + 3(L^2 )(x^2));
where does the maximum
deflection occur?
A. 0.675L
B. 0.578L
C. 0.987L
D. 0.876L
41. A steel support must connect
to 30,000 pound tensile loads
separated by 200 inches. The
maximum allowable stress is
10,000 psi and the maximum
elongation is 0.020 inch. What is
the required area? E(steel) = 3 x
10^7 psi
A. 30.5 mm2
B. 47.1 in2
C. 55 mm2
D. 10 in2
42. High strength steel band saw, 45. What uniform load will cause 48. An elevator weighs 1000
20 mm wide and 0.8 mm thick
simple beam which is 10 ft long pounds and is supported by a
runs over the pulley 600 mm in to deflect 0.3 in. ft it supported 5/16 inch diameter cable, 1500
diameter of pulleys can be used (in addition to the supports) by a feet long. When the elevator
without exceeding the flexural
spring at the beam mid-point.
carries a 1500 lb, the cable
stress of 400 MPa? Note: E = 200 The spring constant of 30,000
elongates 6 inches more. What is
GPa.
lbf/in. Assume the beam is steel, the modulus of elasticity of the
10 in. deep, rectangular, and withcable?
A. 250 cm
a centroidal moment of inertia of
B. 325 mm
100 in4 .
A. 4.35 x 10^7 psi
C. 400 mm
B. 5.87 x 10^7 psi
D. 150 in.
A. 3550 lbf/ft
C. 3.42 x 10^7 psi
B. 6445 lbf/ft
D. 2.34 x 10^7 psi
43. What weight in pounds can
C. 2250 lbf/ft
be lifted by a screw that has an
D. 5440 lbf/ft
49. A hallow shaft has an inner
efficiency of 80% if it is operated
diameter of 0.035 m and an
by a 50 lb force at the end of a 46. During the stress strain test, outer diameter of 0.06 m.
30 inched lever and the pitch of the unit deformation at a stress Compute the torque if the shear
the screw is inch?
of 35 MN/m2 it was 667 x 10^-6 stress is not exceed 120 MPa.
mm. If the proportional limit was
A. 15,080
MN/m2, what is the modulus of
A. 4,500 N-m
B. 15,500
elasticity?
B. 4,300 N-m
C. 10,000
C. 5,500 N-m
D. 12,000
A. 10 x 10^8 N/cm2
D. 3,450 N-m
B. 5.8 x 10^6 N/in2
44. What is the stress in an 8C. 2.1 x 10^5 N/mm2
50. A spherical tank with 10
inch round x 16-inch high
D. 35 x 10^6 N/mm2
inches inside diameter contains
concrete cylinder (E = 2.5 x
oxygen gas at 2,500 psi.
10^6 psi) when the unit
47. A 2.5 in. diameter shaft is 2 Calculate the required wall
deformation is 0.0012 inch/inch? ft. long. Its maximum shear
thickness in (mm) under stress of
stress is 10,000 psi. What is the 28,000 psi.
A. 500 psi
angular deflection in degrees?
B. 8100 psi
A. 6.12 mm
C. 210 psi
A. 0.96o
B. 5.66 mm
D. 3000 psi
B. 0.45o
C. 4.88 mm
C. 0.78o
D. 7.21 mm
D. 0.56o