Documente Academic
Documente Profesional
Documente Cultură
MAINTENANCE/
ADJUSTMENTS
CONTENTS
Chapter 3
MAINTENANCE/ADJUSTMENTS
FS-7000+/FS-9000
1-1-7
Nominal life
Module
(pages)
Toner container
25,000
33,000
DK-33
DK-35
Drum unit
350,000
DV-35
DV-35
Developer unit
350,000
FK-30
FK-35
Fuser unit
350,000
TR-35
TR-35
Transfer roller
350,000
MK-33
MK-35
Refurbishment
350,000
(Maintenance) kit*
Remarks
User-replaceable (20,000
pages for the initially supplied
container)
* To install the kit, refer to the instruction manual included in the kit.
3-1
FS-7000+/FS-9000
Toner container
The toner container is the only consumable that the printer requests (until it has printed
350,000 pages) to replace periodically during normal operation (user-replaceable). The
following toner container is available for use both printer models.
Model
Toner kit
TK-30
TK-30H
Life in pages*
25,000
33,000
FS-7000+/FS-9000
3-2
Then, refer to section Installing toner in chapter 2 to install the new toner container. After
installing the new toner container, several parts in the printer must be cleaned as instructed
in section Cleaning the printer on page Chapter 3-4.
If the toner container has been replaced when the message
3-3
FS-7000+/FS-9000
Grid
Charger wire
Front
FS-7000+/FS-9000
3-4
To clean the charger wire, first open the front cover 1. Pull the cleaning knob (green) 2
slowly in and out a few times. This pulls a cleaning pad inside the drum unit along the wire.
Then, clean the grid using the grid cleaner supplied with the toner kit.
Take the grid cleaner 3 from protective bag in the new toner kit, and remove the cap 4.
The grid cleaner pad is impregnated with water. Perform the following cleaning procedure
before the pad dries.
3-5
FS-7000+/FS-9000
Attach the grid cleaner 3 to the drum unit as shown in the diagram below. Insert the fixture
pin on the cleaner into the hole on the drum unit with the pad facing up.
Hold and pull up the main charger, then draw it out until it stops. Then, push it all the way
in. Repeat this procedure for 5 times or more.
To release the
main charger
unit for pulling,
first pull it up
Then, pull it
horizontally
out.
After cleaning is done, pull the main charger unit in place using the reverse manner of the
above. Close the front cover.
FS-7000+/FS-9000
3-6
Take out the cleaning brush 7 recessed in the front of the paper feed unit. Cleaning the
separation charger (saw-toothed) 8 by sweeping with the brush 9.
8
Lock lever
9
5
3-7
FS-7000+/FS-9000
Obtain the cleaning cloth (Locate in a new toner kit or contact Kyocera). Wipe the
registration rollers 0 and paper ramp ! as shown below.
When cleaning is done, set the paper feed unit back in place by pushing on the handle. Make
sure that the paper feed unit has been correctly seated, turn the lock lever clockwise, close
the front cover.
The printer can get ready for printing approximately 15 seconds after replacing the toner
container.
FS-7000+/FS-9000
3-8
2
Caution: If you ship the developer unit removed from the printer for repair, etc., pack the
developer in the container package designed for this purpose.
3-9
FS-7000+/FS-9000
Caution: Push in the developer unit slow and gently. If the developer contains toner,
pushing in the developer unit rudely can cause the distribution of toner to become
uneven in the far side of the developer. Also, it may risk damaging the connector
at the far end of the developer (and the mating connector in the printer).
FS-7000+/FS-9000
3-10
Relevant display:
MODE
(repeatedly)
Others>
(repeatedly)
>Service>
>>Developer
ENTER
>>Developer?
ENTER
When printer power is turned on again, the printer continually engages in this mode for
several minutes after which the printer reverts to the ready state.
3-11
FS-7000+/FS-9000
de3630.dat
1
Identifies
1
36: FS-7000+
31: FS-9000
FS-7000+/FS-9000
3-12
Relevant display
Ready
Supervisor mode
Downloading
Supervisor mode
Ready
Caution: Do not turn off printer power while data are being downloaded (approximately
one minute).
Confirm the status page shows the new engine version. If the message display indicates
Call service person Dn (n=0, 1, ), refer to section Errors during downloading on page
Chapter 3-15.
Relevant display
Ready
Supervisor mode
3-13
Downloading
FS-7000+/FS-9000
Supervisor mode
Ready
Relevant display
Downloading
Supervisor mode
Ready
Confirm the status page shows the new firmware version (See Appendix B, page B-2). If the
message display indicates Call service person Dn (n=0, 1, ), refer to section Errors during
downloading below.
FS-7000+/FS-9000
3-14
Meaning
Corrective action
3-15
FS-7000+/FS-9000
Fuser temerature
Approx. 200C/ 392F
Approx. 200C/ 392F
Approx. 185C/ 365F
Approx. 185C/ 365F
Transfer bias
-1.7kV*1 or -2.1kV*2
-1.7kV*1 or -2.1kV*2
-2.2kV*1 or -2.4kV*2
FS-7000+/FS-9000
3-16