Documente Academic
Documente Profesional
Documente Cultură
Page 1 of 4
UP
UP
DOWN
DOWN
UP
UP
DOWN
DOWN
DOWN
DOWN
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
7
6
5
4
3
2
1
0
2.
3.
Enter your PIN and press the # button. Your PIN number can be
created from any group of numbers up to 8 digits of your choice.
Note: Do NOT use"#" or "star" key.
4.
Enter Door Code, as determined from the chart at left, and press
the "star" key.
5.
6.
Part 1:
Part 2:
1.
2.
3.
1.
2.
3.
http://www.geniedoor.com/content/programming-instructions.htm
12/18/2008
Garage Door Remote Programming Instructions | Program Garage Door Opener - Genie o... Page 2 of 4
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Find the Learn Code Button and the LED indicator light on your Genie motor head inside the garage. It is usually behind the light lens and close to the
floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. The External Receiver cover must be removed to
access the Learn Code button and the indicator LED. Follow Steps 1 through 3 outlined below:
Press this Learn Code button momentarily. The red LED indicator light will start to blink. It will blink for up to 30
seconds. While it is blinking:
2. Enter your PIN and press the "Up/Down Arrow" key on your keypad. The Learn Code Indicator LED will stay on.
3. Press the "Up/Down Arrow" key again. The Learn Code indicator LED turns off. Wait until the Keypad backlight
turns off (approximately 30 seconds).
4. Test by entering your PIN and pressing the "Up/Down Arrow" key to operate your door.
1.
Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the same PIN:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Enter PIN and press PROG (red LED blinks once per second).
press PROG again (red LED blinks twice per second).
press the number of doors you wish to control (2 key or 3 key).
press PROG (red led blinks several times and turns off).
Decide which Door will be Door #1, #2, and #3.
Press the Learn Code Button on the motor head.
Enter your PIN and press the Up/Down key on the Keypad.
Press the number you have picked for this Door Opener (key 1, 2 or 3)
Press the Up/Down key.
Repeat steps 6 through 9 for each Door Opener.
To make a copy, highlight area and copy into your word program. You can then print out a legible copy of the chart and programming
steps from your word software.
Programming Genie Hardwired Keyless Entry Pads (KEP1) (This keypad has no cover and is
connected to the inside receiver by a special ribbon.)
The outside garage door keypad has a flat ribbon, which slides behind the garage door molding into the garage, and attaches to the Keyless Entry
Receiver box. Behind the receiver's cover is a switch.
http://www.geniedoor.com/content/programming-instructions.htm
12/18/2008
Garage Door Remote Programming Instructions | Program Garage Door Opener - Genie o... Page 3 of 4
Slide the switch to SET. Enter your PIN on the outside keypad, followed by the "star" button. Slide the receiver switch back
to RUN. Test your PIN code followed by the star button.
**To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the
indicator light stops blinking, then proceed to Step 2.
First, match the settings on the Internal Code Setting Switches with the same set of switches in the receiver on the
garage ceiling, as described in the previous programming instructions.
2. Next, move the small programming switch to 'S' (for SET) and press the transmitter button you wish to have
assigned to the above door.
3. Last, return the programming switch to 'R' (for RUN) and press the assigned transmitter button to test the door and
start the door moving. Follow the same procedure for each additional door you wish to program.
1.
http://www.geniedoor.com/content/programming-instructions.htm
12/18/2008
Garage Door Remote Programming Instructions | Program Garage Door Opener - Genie o... Page 4 of 4
http://www.geniedoor.com/content/programming-instructions.htm
12/18/2008