Documente Academic
Documente Profesional
Documente Cultură
TTP224/TTP224N
TonTouchTM
The TTP224/TTP224N TonTouchTM IC is capacitive sensing design specifically for touch pad
controls. The device built in regulator for touch sensor. Stable sensing method can cover diversity
conditions. Human interfaces control panel links through non-conductive dielectric material. The
main application is focused at replacing of the mechanical switch or button. The ASSP can
independently handle the 4 touch pads with 4 direct output pins.
FEATURES
APPLICATION
2009/8/25
Page 1 of 4
Ver :2.0
Preliminary
TTP224/TTP224N
TonTouchTM
BLOCK DIAGRAM
TP0
TP1
TP2
TP3
DIS13
Sensor &
Reference
detecting circuit
Sensor oscillator
circuit
LPMB
MOT0
MOT1
REGEN
TPQ0
TPQ1
TPQ2
TPQ3
TPQ0D
TPQ2D
Touch detecting
circuit
System oscillator
circuit
Key-on & timing
control
Regulator
circuit
VREG
Output
mode
&
driver
circuit
TOG
AHLB
OD
SM
APPLICATION CIRCUIT
TCP224/TCP224N APPLICATION (enable internal regulator)
K0
Cs0
K1
K3
Cs3
TP3
AHLB
20
19
TPQ1
21
TPQ2D
TP2
22
TPQ0
1
TP0
Cs2
TPQ0D
K2
TP1
Cs1
TPQ2 18
TPQ3 17
SM 16
OD 15
TCP224/TCP224N
REGEN 14
VREG
TOG
LPMB
MOT1
10
VSS 12
MOT0
VDD
DIS13 13
11
104
C1
2009/8/25
Page 2 of 4
Ver :2.0
TTP224/TTP224N
TonTouchTM
Preliminary
Option table:
Output mode:
TOG
OD
SM
AHLB
open
open
open
open
open
VDD
open
VSS
open
open
VSS
VDD
VDD
open
open
VDD
open
VDD
VDD
VSS
open
VDD
VSS
VDD
Option features
open
Multi-key mode
VSS
MOT1 MOT0
VSS
VSS
VSS
open
open
VSS
open
open
open
Direct mode, Open drain active low output, Power on state high-Z
VDD
Toggle mode, Open drain active low output, Power on state high-Z
LPMB
Option features
VDD
Fast mode
open
Option features
open
VSS
PS1. On PCB, the length of lines from touch pad to IC pin shorter is better.
And the lines do not parallel and cross with other lines.
2. The material of panel covering on the PCB can not include the metal or the electric
element. The paints on the surfaces are the same.
3. The C1 capacitor must be used between VDD and VSS; and should be routed with
very short tracks to the devices VDD and VSS pins (TTP224/TTP224N).
4. The capacitance Cs0~Cs3 can be used to adjust the sensitivity. The value of
Cs0~Cs3 use smaller, then the sensitivity will be better. The sensitivity adjustment
must according to the practical application on PCB. The range of Cs0~Cs3 value
are 0~50pF.
5. The sensitivity adjustment capacitors (Cs0~Cs3) must use smaller temperature
coefficient and more stable capacitors. Such are X7R, NPO for example.
So for touch application, recommend to use NPO capacitor, for reducing that the
temperature varies to affect sensitivity.
2009/8/25
Page 3 of 4
Ver :2.0
TTP224/TTP224N
TonTouchTM
Preliminary
TCP224/TCP224N APPLICATION (disable internal regulator)
K0
Cs0
K1
K3
Cs3
TP3
AHLB
20
19
TPQ1
21
TPQ2D
TP2
22
TPQ0
1
TP0
Cs2
TPQ0D
K2
TP1
Cs1
TPQ2 18
TPQ3 17
SM 16
TCP224/TCP224N
OD 15
REGEN 14
VREG
TOG
LPMB
MOT1
10
VSS 12
MOT0
VDD
DIS13 13
11
104
C1
Option table:
Output mode:
TOG
OD
SM
AHLB
open
open
open
open
open
VDD
open
VSS
open
open
VSS
VDD
Option features
open
Multi-key mode
VSS
MOT1 MOT0
VDD
open
open
VDD
open
VDD
VDD
VSS
open
VDD
VSS
VDD
VSS
VSS
VSS
open
open
VSS
open
open
open
Direct mode, Open drain active low output, Power on state high-Z
VDD
Toggle mode, Open drain active low output, Power on state high-Z
LPMB
Option features
VDD
Fast mode
open
Option features
open
VSS
PS1. On PCB, the length of lines from touch pad to IC pin shorter is better.
And the lines do not parallel and cross with other lines.
2. The power supply must be stable. If the supply voltage drift or shift quickly, maybe
causing sensitivity anomalies or false detections.
3. The material of panel covering on the PCB can not include the metal or the electric
element. The paints on the surfaces are the same.
4. The C1 capacitor must be used between VDD and VSS; and should be routed with
very short tracks to the devices VDD and VSS pins (TTP224/TTP224N).
5. The capacitance Cs0~Cs3 can be used to adjust the sensitivity. The value of
Cs0~Cs3 use smaller, then the sensitivity will be better. The sensitivity adjustment
must according to the practical application on PCB. The range of Cs0~Cs3 value
are 0~50pF.
6. The sensitivity adjustment capacitors (Cs0~Cs3) must use smaller temperature
coefficient and more stable capacitors. Such are X7R, NPO for example.
So for touch application, recommend to use NPO capacitor, for reducing that the
temperature varies to affect sensitivity.
2009/8/25
Page 4 of 4
Ver :2.0