Documente Academic
Documente Profesional
Documente Cultură
Supplies:
PDF Created with deskPDF PDF Writer - Trial :: http://www.docudesk.com
Tips
20. Cut (4) from light weight chipboard 3-7/8 x 6 (I use the
backing of any Printed Paper pad I have bought).
21. Cut (8) from Printed Paper 3-7/8 x 6.
22. Adhere the printed paper to the light weight chipboard.
15. Cut (4) from Brown Card Stock 3-7/8 x 6 (I cut 2 brown and
2 green).
16. Place your list on the Brown card stock matching closer to
the bottom. Once you have your pieces centered place a
brad in each upper corner. I use brads so that I can keep
adding as I need new list.
23. Cut (1) from the poster Write on/Wipe off poster board 7-¼
x 5-1/4.
24. Stamp with stamps of your choice. (I only stamped in the 31. Adhere to the top of the envelope.
bottom and upper right hand corners) 32. For small pockets cut (2) at 4 x 2 from Card Stock (I cut (1)
25. Cut (1) from Green Card Stock 7-3/4 x 5-3/4. green and (1) brown)
26. Adhere the Write on/ Wipe off piece to the Card Stock. 33. Cut (2) from Printed Paper 3-7/8 x 1-7/8
27. Cut a piece of Brown Grosgrain ribbon 30” tie around both 34. Adhere to the Card Stock.
pieces at the top.
35. Adhere the Write on/Wipe off matted piece to one of the 6 x
28. To create the envelope pockets you will cut (2) from Card 12 pieces of Chipboard.
Stock (I cut (1) green and (1) brown) 4 x 3-1/4. 36. Adhere the Calendar to the side of the Write on/Wipe off
29. Cut from printed Paper (2) 3-7/8 x 3-1/8 adhere to the card Board.
stock.
37. Adhere the envelope pockets and small pockets to the other 39. Using your 1-1/4” Circle Scallop punch, punch (2) from
6 x 12 Chipboard piece. Green Card Stock and (2) from Brown Card Stock.
38. Be sure to only glue the two sides and bottom so that you 40. Print out the Tags
can use it as a pocket. 41. Punch out the tags using the 1” Circle Scallop punch.
42. Sponge the edges of the tags (2) with brown and (2) with
green ink.
43. Stamp an image in the center of the tag.
44. Adhere the printed tags to the Card stock. Set aside for
later.
45. The following steps are for those who have the BIND-IT-
ALL.
46. If you do not have the bind it all you can still bind your
project together with punched holes and ribbon.
62. Once you have outlined all the way across you can now take 66. Follow manufactories directions for punching across.
the paper clips off. 67. You will do this for each section.
63. You will now punch each section with the Bind-It-All.
68. You will place each of the 6 x 12 pieces back to back for
64. Place the sections 1 at a time still stacked by section into the binding. Then stack each section staggered 2-1/2” apart
Bind-it-All. (You will have (1) cover and (1) matted list). onto the 6 x 12 side with the envelopes on it.
65. You will line the outlined punch lines up to the machine for
correct line up.
69. Place project in Bind-It-All to bind it all together. 76. Cut 3 from printed Paper 3/8” x 2 3/8”
77. Adhere to 3 sides.
70. Now that your project is bound you will now decorate and
embellish it. 78. Adhere to the project.
71. To create the Dry Eraser pen Holder you will cut a piece of 79. I cut Tags out from Planton Cricut Cartridge at 2” and 4”.
Card Stock 2-1/4 x 3. 80. I used the stamp sets CTMH – Library Cards, Checklist,
72. Score on short side @1/2, 1, 1-1/2, 2”. Journaling Jots and adhered them to the tags to be placed in
73. Turn and score @ ½” on long side the envelope pocket holders.
74. Fold score lines and cut slits at the bottom of the box.
75. Assemble box
81. I used tabs I had that went with this paper pack to divide
each section and then adhered my tabs to the top of them.