Documente Academic
Documente Profesional
Documente Cultură
EUROPEAN STANDARD
NORME EUROPENNE
EN 22341
EUROPISCHE NORM
July 1992
(www.freebz.net)
English version
UDC 621.882.6
w.
fx
w.
bz
GEN
--```,-`-`,,`,,`,`,,`---
(www.freebz.net)
CEN E N * 2 2 3 4 1 92
3404589 0034097 T T 9
(www.freebz.net)
Page 2
EN 22341 : 1992
Foreword
(www.freebz.net)
--```,-`-`,,`,,`,`,,`---
w.
bz
fx
w.
CEN EN1223irl 9 2
(www.freebz.net)
Page 3
EN 22341 : 1992
w.
--```,-`-`,,`,,`,`,,`---
This International Standard specifies the characteristics of clevis pins with head, with metric dimensions and nominal diameters, d,
from 3 to 100 mm inclusive.
2 References
fx
- Acceptance inspection.
w.
bz
(www.freebz.net)
CEN ENu2234L 92
3404589 0034099 8 7 1
(www.freebz.net)
Page 4
EN 22341 : 1992
3 Dimensions
Surface roughness values in microrratres
Type A
Without split pin hole
Type
With split pin hole
w.
Radius permissible
NOTES
fx
/e
--```,-`-`,,`,,`,`,,`---
w.
bz
NOTE For railway applications and in cases where the split pins are subjected to alternating transverse forces, it is recommended that the next
larger split pin and corresponding hole diameter to that specified be used.
(www.freebz.net)
CEN E N x 2 2 3 4 L 9 2
(www.freebz.net)
Page 5
EN 22341 : 1992
hll?
10
12
14
16
18 2022
24
36
27
a)3336404550556070
80
90 lo(
h14
22
25
28
30 33
di
H1$?
0,8
1,2
1,6
3.2
3,2
5 5
6,3
6,3
8 8 8 8 10 10 10 10 13
13
13
max.
4 4
4 4 4 4 4 4 6 6 6
11,61,61,61,622
14
18
20
js14
1,6
?e
min.
1,6
2,2
2,9
3.2
3.5
4,5
5,5
max.
6
8
10
5,7t
7,7!
9,7!
625
8.25
10.25
12
14
16
11,5
13,5
15.5
12.5
14.5
16,5
18
17.5
20 19,5
22 21,5
18,5
20,5
22.5
24
26
28
23.5
25,5
27.5
24.5
26,5
28.5
30 29,5
31,5
34.5
30,5
32.5
35.5
50
39.5
44,5
49.5
40,5
45.5
50.5
!i5
60
65
54,2E
59,2E
64,2t
55,75
60.75
65,75
70
69,Zt
74,2!
32
35
40
75
80
85
90
95
140,75
160,75
180,75
200.75
200 199,2!
13
13
5 5,5
8 8
10 10 10 10 12 12 14 14 16
16
16
1 1 1 1 1 1 1 1 1
1 Other tolerances, for example al 1, cl 1, f8, as agreed between customer and supplier.
2) Hole diameter d, = nominal size of the split pin (see I S 0 1234).
3) For nominal lengths above 200 mm, steps of 20 mm.
--```,-`-`,,`,,`,`,,`---
160 159,2!
180 179,2!
8 8 8 8
1:
9 9 11 12 13
85.75
90,75
95,75
140 139.2
4,5
70.75
75,75
79,2 80.75
84,2f
89,21
94,2t
w.
bz
45
fx
13)
,om./ min.
0,60,60,60,60,60,60,60,60,61
40
w.
0,50,51
10
(www.freebz.net)
11
CEN E N * 2 2 3 4 L 92
(www.freebz.net)
Page 6
EN 22341 : 1992
I
I
, Surface finish
Plain, .e. pins to be supplied in natural finish treated with a rust-preventative lubricant, unless otherwise
specified by agreement between customer and supplier.
Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conversion coating
(seeIS0 2081 and IS0 4520).
Other coatings as agreed between customer and supplier.
All tolerances shall apply prior to the application of a plating or coating.
Workmanship
Acceptability
w.
Material
5 Designation
--```,-`-`,,`,,`,`,,`---
Example for the designation of a clevis pin, steel, type 6,with nominal diameter d = 20 mm and nominal length I= 100 mm :
fx
Example for the same pin with a split pin hole of Q 6,3 mm :
- St
- -
w.
bz
Example for the same pin with a standard split pin hole :
(www.freebz.net)