Documente Academic
Documente Profesional
Documente Cultură
AN7125
Dual Channel BTL Power Amplifier
■ Overview Unit : mm
AN7125 is a monolithic integrated circuit designed for 7.7±0.3
12
13.5 W (12 V,4 Ω) output audio power amplifier.It is a
(1.3)
dual channel BTL IC suitable for stereo operation in radio
cassette and TV application.
(10.0)
φ3.6
(1.27)
29.75±0.30
28.0±0.3
20.0±0.3
29.6±0.3
■ Features
+0.15
R1.8
0.6
• Built-in thermal shutdown protection circuit
1.45±0.15
• Built-in current limiting circuit
+0.10
(12.5)
• High power : (13.5 W/12 V/4 Ω)
3.5±0.3
1.2±0.1
(13.0 W/15 V/8 Ω)
1.80±0.15
(1.2)
■ Block Diagram
REF
TSD
protection
circuit
Standby Mute
circuit
10
11
12
1
9
VCC
GND
GND
GND
1
AN7125 ICs for Audio Common Use
■ Pin Descriptions
Pin No. Description Pin No. Description
1 VCC 7 Pre GND
2 ch.1 + ve Phase Output 8 ch.2 Input
3 ch.1 Output GND 9 Mute
4 ch.1−ve Phase Output 10 ch.2 −ve Phase Output
5 Standby 11 ch.2 Output GND
6 ch.1 Input 12 ch.2 +ve Phase Output
2
ICs for Audio Common Use AN7125
600 Ω 30 kΩ 3
4 ch.1 O/P : VCC/2
ch.1 inverse phase output pin.
VCC/2
5 kΩ
5 kΩ 10 kΩ 2 kΩ
2 kΩ
8
6 ch.1 Input : 0V
200 Ω 400 Ω This is the amplifier input pin.
Pin6,8
30 kΩ
7 Pre GND : 0V
Input ground pin.
3
AN7125 ICs for Audio Common Use
Pin6,8
30 kΩ
7
20 kΩ
600 Ω 30 kΩ 11
12 ch.2 Output : VCC/2
ch.2 positive phase output pin
VCC/2
4
ICs for Audio Common Use AN7125
7 GND
Input
VCC
2200 µF
1
2 OUT1
6 Output1 0.22 µF
IN1
3 GND 2.2 Ω RL
4Ω
4 OUT1
0.22 µF
51 kΩ 5 2.2 Ω
5V
STB
Cs
10 µF
8.2 kΩ 9
MUTE
Cs
33 µF 10 OUT2
Output2 0.22 µF
11 GND 2.2 Ω RL
8 4Ω
IN2
12 OUT2
0.22 µF
2.2 Ω
STB 'Off' 5V
STB 'On' 0V
Mute 'Off' 0V
Mute 'On' 5V
■ Application’s Precautions
1. External heatsink is needed when used. External heatsink should be fixed to the chassis.
2. Fin of the IC can be connected to GND.
3. Please prevent output to VCC short and output to GND short.
4. The temperature protection circuit will operate at Tj around 150 °C.
However, if temperature decrease, the protection circuit will automatically be decreased and resume
normal operation.
5
AN7125 ICs for Audio Common Use
■ Technical Information
• HSIP012-P-0000A
PD Ta
80
70
50
(1)
40
30
20.8 W
20
15.6 W (2)
(3)
10
3.0 W (4)
0
0 25 50 75 100 125 150
VCEmax = 30 V
ICmax = 8 A
10
5 t = 0.2 ms
t = 1.0 ms
IC (A)
2
t = 10 ms
1
0.5
0.2
0.1
1 2 5 10 20 50 100
VCE (V)
6
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.
2001 MAR
This datasheet has been download from:
www.datasheetcatalog.com