Documente Academic
Documente Profesional
Documente Cultură
131826)
Document number:
Document issue:
Document status:
Date:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
UMT/BTS/DJD/044741
V01.01/EN
Approved standard
11/Nov/2014
Alcatel-Lucent Proprietary Use pursuant to applicable agreementsPassing on or copying of this document, use and communication of its
contents not permitted without AlcatelLucent written authorization
Legal notice
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other
trademarks are the property of their respective owners
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for
inaccuracies contained herein.
Copyright 2010 Alcatel-Lucent. All rights reserved.
34
35
Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made
available to, or copied or used by anyone outside Alcatel-Lucent without its written authorization.
36
37
38
PUBLICATION HISTORY
24/September/2014
39
40
41
42
43
11/November/2014
44
45
46
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 2/174
CONTENTS
47
48
INTRODUCTION ........................................................................................................................ 6
49
1.1 OBJECT...................................................................................................................................... 6
50
51
52
2.1
53
54
DOCUMENTS............................................................................................................................. 6
55
3.1
IBTS CONFIGURATIONS
56
3.2
57
58
59
3.2.1
ENTRY CRITERIA: ........................................................................................................... 7
3.2.2
EXIT CRITERIA: .............................................................................................................. 7
3.3 TEST ENVIRONMENT .................................................................................................................. 7
60
3.4
61
3.5
3.5.1
3.5.2
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
.............................................................................................................. 7
TESTS DESCRIPTION............................................................................................................... 13
4.1
4.1.1.
OAM TEST ................................................................................................................ 13
4.1.1.1. PM_COUNTER .................................................................................................. 13
4.1.1.2. OMCB OPERATION ............................................................................................... 18
4.1.1.3. TIL OPERATION .................................................................................................... 20
4.1.2.
RADIO TEST .............................................................................................................. 22
4.1.2.1. BASIC CALL ......................................................................................................... 22
4.1.2.2. RADIO POWER TEST ............................................................................................. 29
4.1.2.3. R99 TEST ............................................................................................................ 30
4.1.2.4. HSUPA RESOURCE .............................................................................................. 32
4.1.2.5. MOBILITY TEST ..................................................................................................... 32
4.1.2.6. RADIATING ........................................................................................................... 35
4.1.3.
ENDURANCE .............................................................................................................. 39
4.1.3.1. OAM EDURANCE .............................................................................................. 39
4.1.3.2. RADIO EDURANCE ........................................................................................... 42
4.1.4.
UA6.0 FEATURE TEST ................................................................................................ 43
4.1.4.1. MIX MODE ........................................................................................................... 43
4.1.4.2. AISG-LITE........................................................................................................... 43
4.1.4.3. 10/20KM FIBER .................................................................................................... 44
4.1.4.4. 6 CPRI LINK ....................................................................................................... 47
4.1.4.5. POWER POOLING .................................................................................................. 58
4.1.5.
UA7.1 GENERAL TEST DESCRIPTION FOR FRS33519 DAISY CHAIN ................................. 61
4.1.5.1. LINK STATUS ........................................................................................................ 61
4.1.5.2. LOOP BACK .......................................................................................................... 63
4.1.5.3. ALARM ................................................................................................................ 64
4.1.5.4. PLUG IN/OUT ........................................................................................................ 65
4.1.5.5. SW UPGRADE ...................................................................................................... 66
4.1.5.6. DOWNLOAD ......................................................................................................... 69
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 3/174
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
125
126
127
128
129
130
131
132
SETUP/DELETE ONE CELL ON 21C RRH WITH ASB PA VENDOR ........................................ 168
SETUP/DELETE TWO CELLS ON 21C RRH WITH ASB PA VENDOR ...................................... 169
SETUP/DELETE THREE CELLS ON 21C RRH WITH ASB PA VENDOR .................................... 169
SETUP/DELETE FOUR CELLS ON 21C RRH WITH ASB PA VENDOR ..................................... 170
SETUP/DELETE ONE CELL ON 21C RRH WITH GEWEI PA VENDOR ..................................... 171
SETUP/DELETE TWO CELLS ON 21C RRH WITH GEWEI PA VENDOR ................................... 171
SETUP/DELETE THREE CELLS ON 21C RRH WITH GEWEI PA VENDOR ................................. 172
SETUP/DELETE FOUR CELLS ON 21C RRH WITH GEWEI PA VENDOR................................... 173
133
5.
134
6.
ABBREVIATIONS................................................................................................................ 174
135
136
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 4/174
137
138
139
140
141
142
143
List of Figures
FIGURE 1: ISS TEST ENVIRONMENT FOR STAR MODE ............................................................. 8
FIGURE 2 ISS TEST ENVIRONMENT FOR DAISY CHAIN MODE ............................................ 9
FIGURE 3: STARTUP WITHOUT FIRST SCAN FAST ................. ERROR! BOOKMARK NOT
DEFINED.
FIGURE 4: AISG IN TIL ................................................ ERROR! BOOKMARK NOT DEFINED.
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
List of Tables
TABLE 1: REGRESSION CASE COVERAGE LIST ............................................................... 11
TABLE 2 : FEATURE CASE COVERAGE LIST ..................................................................... 12
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 5/174
160
1 INTRODUCTION
161
1.1 OBJECT
162
163
This document mainly describes the test strategy, test cases and cases description for FRS
131826.
164
165
166
The purpose of this document is to describe the ISS test that should to be done in order to
validate ASB_RRH60W 21C used in UMTS. The test platforms are on rack (2U, 2UV2, 2UV3,
and V5 if it is possible) in release LR15.2.
167
168
169
170
Test configuration, test coverage, test cases list and cases description.
171
172
173
1.
This document can be a reference for ASB_RRH60W 21C PowerSaving DEV team
174
2.
This document can be a reference for ASB_RRH60W 21C PowerSaving PRI_INT team
175
3.
This document can be a reference for ASB_RRH60W 21C PowerSaving ISS team
176
177
4.
178
2 DOCUMENTS
179
2.1
REFERENCE DOCUMENTS
180
[R1]
STISS_FOR_ASB_RRH_v01.02
181
[R2]
FN131825&131826_Power_saving_for_RRH60_21C&RRH2x60
182
[R3]
HLD_LLD_PowerSaving_131825_131826
183
[R4]
184
[R5]
185
[R6]
186
[R7]
187
[R8]
188
189
[R9]
190
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 6/174
191
192
3.1
193
All configurations include STSR1/2/3, STSR1+1/2+1/2+2 in star and daisy chain mode.
IBTS CONFIGURATIONS
194
195
3.2
196
3.2.1
Entry Criteria:
197
198
199
200
All test tools (including Lamp, Lamp, TM500, UE, and so on) should be ready and work
well
201
3.2.2
202
100% of identified tests executed with >85% pass rate at TCFP without critical CR
203
204
205
206
ISS Test Report- identifies feature testing done and any problems found
207
3.3
TEST ENVIRONMENT
In this section, it describes the configuration of test environment.
208
209
210
211
Exit Criteria:
1.
Star Mode
During the test campaign of ASB RRH, we will config RRH as Star mode as following
figure 1.
212
213
In this configuration, it is possible to config platform with STSR1, STSR2, STSR3, STSR4,
STSR x+y.
214
215
216
217
Note: There are some restrictions of SW, the max cell is 12 on BTS. So we can config 12
cells or less than 12 cells on BTS. For STSRx+y, we should be config paried RRH as
following configuration: 01 and 04, 02 and 05, 03 and 06 with paired RRH, 01,02,03 is
Main RRH, and 04,05,06 is Diversity RRH.
218
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 7/174
Optical
Fiber Line
RRH01
RRH02
PCM
Cable
catapult
ATM switch
RRH03
dBTS/2UV1/2UV2
RRH04
Ethernet Line
Ethernet switch
Ethernet Line
Ethernet Line
RRH05
RRH06
OMC-B
TIL
219
220
221
222
223
224
2.
225
226
227
228
229
230
231
Note: There are some restrictions of SW, the max cell is 6 on one fiber chain. So we can
config 6 cells or less than 6 cells on one fiber chain. For STSRx+y, we should be config
paried RRH with conjoint RRH, and set RRH with minor reuid as Main RRH, and larger
reuid as Divesity RRH. For example: 01 and 02, 03 and 04, 05 and 06 with paired RRH,
01,03,05 is Main RRH, and 02,04,06 is Diversity RRH.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 8/174
PCM
Cable
catapult
Optical
Fiber Line
ATM switch
RRH01
RRH02
RRH03
RRH04
RRH05
RRH06
dBTS/2UV1/2UV2
Ethernet Line
Ethernet switch
Ethernet Line
Ethernet Line
OMC-B
TIL
232
233
234
235
Hardware Requirement:
236
1)
237
2)
238
3)
239
4)
240
5)
241
6)
242
7)
243
Software Requirement:
244
245
1)
Test
platform
package,TIL,etc )
246
2)
247
Link Setup:
248
1)
249
2)
250
3)
251
4)
252
5)
2UV2/3/5
package(included
ASB_RRH2X60W_850/1900/2100
253
254
3.4
255
The following rules will be adopted for feature ASB RRH 60 21C test progress tracking:
256
257
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 9/174
259
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 10/174
260
3.5
261
3.5.1
263
3.5.2
264
1.
262
regression coverage:
Basic functions
Specific functions
V7 features
AISG
21
COMMEN MEASUREMENT
FAULT MANAGEMENT
FUNCTIONMODE MANAGEMENT
3
4
OAM
RADIO MOBILITY
DOWNLOAD PHASE 3
LONG FIBER
TMA
DAISY CHAIN
20
STSR X+Y
15
SUM
90
26%
32%
42%
100%
265
266
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 11/174
267
268
2.
feature coverage:
AISG
21
13.3%
ALARM
35
22.2%
FAULT MANAGEMENT
1.9%
BASIC RADIO
1.9%
MOBILITY
1.2%
RADIATING
1.9%
RADIO POWER
0.6%
MIX MODE
0.6%
LONG FIBER
1.2%
6 CPRI LINK
3.1%
POWER POOLING
1.2%
DAISY CHAIN
20
12.7%
STSRX+Y
15
9.5%
CAPACITY LICENSE
1.2%
0.6%
1.2%
VSWR
3.1%
SINGLE RX PORT
1.2%
EXTERNAL ALARM
0.6%
UNBLANCE RF POWER
0.6%
AC POWER
1.9%
PM COUNTER
3.1%
OAM
2.5%
POWER SAVING
5%
STABILITY
10
7.4%
Total
157
100%
269
270
271
272
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 12/174
273
TESTS DESCRIPTION
274
4.1
275
4.1.1.
276
4.1.1.1.
277
278
Purpose:
279
280
Requirement:
281
282
Lamp connection
283
284
Discussion:
285
286
287
This load counter is used to measure the min/max/avg of the WideBand received power per sector per
frequency at the Rx Main Channelizer as detected by RRH/TRDU. The values are shown in 10^-12
mW.
288
Procedure:
289
290
Step2:setup 1 cell
291
Step3:in PM menu, activate the fastclock for pm file generation, PMFastclock a, check Result1&2
292
Step4:delete this cell, setup 1 cell on the other RRH/TRDU, check Result3
293
Expectable results:
294
Result1:check that the min/max/avg values shown by counter #10201 under PM>display
295
Result2:the values are shown in 10-12 mW, and as same as what is reported from RRH/TRDU
296
297
Result3:after cell setupcell deletioncell setup, the counter could collect and report continuously
Regression Test
OAM TEST
PM_COUNTER
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 13/174
298
299
300
Purpose:
301
302
Requirement:
303
304
Lamp connection
305
306
Discussion:
307
308
This load counter is used to measure the min/max/avg of the WideBand received power per sector per
frequency at the Rx Div Channelizer as detected by TRM. The values are shown in 10-12 mW.
309
Procedure:
310
311
Step2:setup 1 cell
312
Step3:in PM menu, activate the fastclock for pm file generation, PMFastclock a, check Result1&2
313
Step4:delete this cell, setup 1 cell on the other RRH/TRDU, check Result3
314
Expectable results:
315
Result1:check that the min/max/avg values shown by counter #10202 under PM>display
316
Result2:the values are shown in 10-12 mW, and as same as what is reported from RRH/TRDU
317
318
Result3:after cell setupcell deletioncell setup, the counter could collect and report continuously
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 14/174
319
320
References :
Test label 1:PM_COUNTER_10204_MCPA_PWR
321
Purpose:
322
323
Requirement:
324
325
Lamp connection
326
327
Discussion:
328
329
This load counter is used to measure the min/max/avg of the output MCPA Power detected by
RRH/TRDU. The values are shown in mW.
330
Procedure:
331
332
Step2:setup 1 cell
333
Step3:in PM menu, activate the fastclock for pm file generation, PMFastclock a, check Result1&2
334
Step4:delete this cell, setup 1 cell on the other RRH/TRDU, check Result3
335
Expectable results:
336
Result1:check that the min/max/avg values shown by counter #10204 under PM>display
337
Result2:the values are shown in mW. In cpri mode, RRH/TRDU wont report PA power to Rack2u. Now
cell n
Txpower
338
339
340
341
Result3:after cell setupcell deletioncell setup, the counter could collect and report continuously the
occurence of ./Board/RRH or ./Board/TRDU should be equal to physical number of RRH/TRDU when
its status is L3_connected && Unlocked && SoftStateOk, nothing with cell setup and cell deletion
342
343
cell 0
/frequency number
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 15/174
344
345
346
Purpose:
347
The purpose of this test is to check the management of the RadioTxCarrierPwr counter
348
Requirement:
349
350
Lamp connection
351
352
Discussion:
353
354
This load counter is used to measure the min/max/avg of the total transmitted power per sector per
frequency at the Tx channelizer as detected by RRH/TRDU. The values are shown in mW.
355
Procedure:
356
357
Step2:setup 1 cell
358
Step3:in PM menu, activate the fastclock for pm file generation, PMFastclock a, check result1&2
359
Step4:delete this cell, setup 1 cell on the other RRH/TRDU, check result3
360
Expectable results:
361
Result1:check that the min/max/avg values shown by counter #10205 under PM>display
362
Result2:the values are shown in mW, and as same as what is reported from RRH/TRDU
363
364
365
Result3:after cell setupcell deletioncell setup, the counter could collect and report continuously
366
367
368
Purpose:
369
370
Requirement:
371
372
Lamp connection
373
374
Discussion:
375
376
This load counter is used to measure the min/max/avg of the output CPU load detected by RRH/TRDU.
The values are shown in percentage.
377
Procedure:
378
379
Step2:setup 1 cell
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 16/174
380
381
382
383
384
Expectable results:
-
The values are shown in percentage as same as that reported from RRH/TRDU. And the cpu load
should not be very high, about 50-60%
385
386
387
388
389
After cell setupcell deletioncell setup, the counter could collect and
report continuously
390
391
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 17/174
392
393
4.1.1.2.
OMCB OPERATION
394
395
Purpose:
396
397
Check BTS will under control of OMCB when unlock BTS while BTS will out of control of OMB when
lock BTS
398
Requirement:
399
400
Procedure:
401
402
403
404
Expectable results:
405
406
407
408
409
410
411
412
When BTS is lock, BTS could not be controlled from OMCB(SW upgrade,
Equipment Monitor, etc.)
413
414
415
416
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 18/174
417
418
Purpose:
419
Check the cell(s) are correctly configured when RRH (in STSR-1) is locked and unlocked
420
Requirement:
421
422
Procedure:
423
424
425
426
Step3:send commands from lamp in order to configure the Cells, Fach and Rach channels, check
result3
427
428
429
Expectable results:
430
431
Result1:check that all the local cells are disabled (Audit Response message raised to the lamp
including all the local cells to delete)
432
433
434
435
Result2:when RRH is up, check that all the local cells are enabled (RSI message raised to the lamp
including the local cells to add)
436
437
438
Result3:check cell setup response, Fachsetup response and Rachsetup response are successful.
439
440
441
Result5:when NodeB is up, check the RRH remains locked (no local cell enabled raised to the lamp)
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 19/174
442
443
4.1.1.3.
TIL OPERATION
444
445
Purpose:
446
447
Requirement:
448
TIL connection
449
Procedure:
450
451
Step2:once download is completed, give activation and reset from TIL, then check result1&2
452
Expectable results:
453
Result1:check whether NodeB comes up properly with the new upgraded load
454
455
456
457
Purpose:
458
459
Requirement:
460
TIL connection
461
Lamp connection
462
Procedure:
463
464
465
Step 2:On TIL, send a reset to the RRH on the RRH display
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 20/174
466
467
468
Expectable results:
469
470
Result1:RRH chould be reset and up normally, check that all the local cells are enabled (Audit
response message raised to the lamp including the local cells to add).
471
472
Result2:RRH chould be reset and up normally, check that all the local cells are enabled (Audit
response message raised to the lamp including the local cells to add).
473
474
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 21/174
475
476
477
Purpose:
478
479
Requirement:
480
481
TIL connection
482
Procedure:
483
484
485
Expectable results:
486
487
4.1.2.
488
4.1.2.1.
489
490
Purpose:
491
492
Check that the NodeB can correctly communicate with a TM500 on both UL and DL for a designated
Radio Bearer
493
Requirement:
494
495
496
497
The radio configuration is STSRx+y in star/chain mode or STSRz in daisy chain mode
498
Procedure:
499
RADIO TEST
BASIC CALL
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 22/174
500
501
Step2:establish a radio link (AMR_12k2, ps32k, ps64k, ps128k and ps384k) each cell on the NodeB
and on the TM500, check Result2
502
Step3:generate AAL2 traffic and check the BLER value, on Uplink and Downlink, Check Result3
503
Expected results:
504
505
506
507
(The below is an example of Lamp command and TM500 script by manual test)
AMR_12k2
Lamp
TM500
cellset 0
fachset 0
rachset 0
rlset 0 1 amr_12k2_6
cellsearch
UBI_SETUP_BCH_SC1
UBI_SETUP_AMR_12K2_6TFC_OVSF65_SC1
test 1
//check Bler on capa
UBI_CLEARSTATS
GETSTATS_CELL
GETSTATS_DCH
508
PS_32k
Lamp
TM500
cellset 0
fachset 0
rachset 0
rlset 0 1 ps_32k_10
cellsearch
UBI_SETUP_BCH_SC1
UBI_SETUP_PS_32K_10TFC_OVSF5_SC1
test 1
//check Bler on capa
UBI_CLEARSTATS
GETSTATS_CELL
GETSTATS_DCH
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 23/174
509
PS_64k
Lamp
TM500
cellset 0
fachset 0
rachset 0
rlset 0 1 ps_64k_10
cellsearch
UBI_SETUP_BCH_SC1
UBI_SETUP_PS_64K_10TFC_OVSF5_SC1
test 1
//check Bler on capa
UBI_CLEARSTATS
GETSTATS_CELL
GETSTATS_DCH
510
PS_128k
Lamp
TM500
cellset 0
fachset 0
rachset 0
rlset 0 1 ps_128k_10
cellsearch
UBI_SETUP_BCH_SC1
UBI_SETUP_PS_128K_10TFC_OVSF5_SC1
test 1
//check Bler on capa
UBI_CLEARSTATS
GETSTATS_CELL
GETSTATS_DCH
511
PS_384k
Lamp
TM500
cellset 0
fachset 0
rachset 0
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 24/174
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 25/174
514
515
516
Purpose:
517
Check that the NodeB can correctly communicate with a TM500 on both UL and DL for an hsdpa128
518
Requirement:
519
520
521
522
The radio configuration is STSRx+y in star/chain mode or STSRz in daisy chain mode
523
Procedure:
524
525
526
Step2:establish a radio link respectively (hsdpa128) on each cell of HSDPA activation and on the
TM500, check Result2
527
Step3:generate AAL2 traffic and check the BLER value, on Uplink and Downlink, check Result3
528
Expected results:
529
530
531
532
(The below is an example of Lamp command and TM500 script by manual test)
HSDPA
Lamp
TM500
cellset 0
fachset 0
rachset 0
physcrec 0
rlset 0 1 hsdpa128
cellsearch
UBI_SETUP_BCH_SC1
UBI_SETUP_HSDPA_ASSOCIATED_DCH_UL128_OVSF65_SC1
FORCE_NACK_9ACK_CQI
UBI_SETUP_HSDPA_RL_L1_SC1_CAT12
test 1 mode=1 capareq=1 delay=100
//check Bler on capa
//check DL rate by TM500
UBI_CLEARSTATS
GETSTATS_CELL
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 26/174
GETSTATS_DCH
GETSTATS_HSDPA
533
534
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 27/174
535
536
537
Purpose:
538
Check that the NodeB can correctly communicate with a TM500 on both UL and DL for an hsdpa_edch
539
Requirement:
540
541
542
543
The radio configuration is STSRx+y in star/chain mode or STSRz in daisy chain mode
544
Procedure:
545
546
547
Step2:establish a radio link respectively (hsdpa_edch) on each cell of HSUPA activation and on the
TM500, check Result2
548
Step3:generate AAL2 traffic and check the BLER value, on Uplink and Downlink, check Result3
549
Expectable results:
550
551
552
553
(The below is an example of Lamp command and TM500 script by manual test)
HSUPA ( L1)
Lamp
TM500
cellset 0
fachset 0
rachset 0
physcrec 0 type=full
rlset 0 1 hsdpa_edch
cellsearch
UBI_SETUP_BCH_SC1
UBI_SETUP_SRB_3K4_OVSF65_SC1
UBI_SETUP_HSDPA_EDCH_PN_ALL_N_TABLE_1_SC1_n1
test 1 mode=1 edch_mode=1
//check Bler on capa
//check DL and UL rate by TM500
UBI_CLEARSTATS
GETSTATS_CELL
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 28/174
GETSTATS_DCH
GETSTATS_HSDPA
GETSTATS_HSUPA
554
HSUPA ( L2)
Lamp
TM500
cellset 0
fachset 0
rachset 0
physcrec 0 type=full
rlset 0 1 hsdpa_edch
cellsearch
L2_SETUP_BCH_10612_9662_SC1
L2_SETUP_DCH_SC1
L2_SETUP_HSDPA_SC1
L2_SETUP_EDCH_SC1
test 1 mode=1 edch_mode=1
L2_config_MAC_e
L2_SI_0_20
L2_SI_0_97
//check Bler on capa
//check DL and UL rate by TM500
555
556
4.1.2.2.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 29/174
557
558
Purpose:
559
560
The goal of this test case is to verify the RSSI reported at RRH/TRDU side is as expected at any case
561
562
563
Procedure:
564
565
Step1:Thanks to Lamp, cellset without any signal injection, then Start the common measurement with
the command:
Requirements:
566
567
568
569
Step3:Disconnect one antenna connection. Thanks to Lamp, cellset without any signal injection, then
Start the common measurement with the command:
Startcmeas cellid measurementid
570
571
572
573
574
Expectable results:
575
4.1.2.3.
576
577
R99 TEST
Purpose:
578
579
Requirement
580
581
582
Test inputs:
583
584
585
586
Frequency:B / M / T
587
Bearer:ex:PS_64K_10
588
Cell:0 / 1 / 2
589
The UL & DL SIR targets should relate to good radio conditions, ex:5 dB in DL / 10 dB in UL.
590
591
592
593
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 30/174
594
595
596
597
The call must be checked during 1 night (the AAL2 traffic should not be disrupted during the
night).
598
599
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 31/174
600
601
4.1.2.4.
602
603
604
Purpose:
605
606
Requirement
607
608
HSUPA RESOURCE
609
610
Test inputs:
611
612
613
614
Frequency:B / M / T
615
Cell:0 / 1 / 2
616
617
The UL & DL SRB SIR targets should relate to good radio conditions, ex:5 dB in DL / 10 dB in UL.
618
619
620
621
The default values for the HSDPA parameters will be applied in the NodeB MIB (DLU), except the
hsdpaCqiBlerAdjustmentAlgorithm that will be turned off (0).
622
The default values for the EDCH parameters will be applied in the NodeB MIB (DLU).
Procedure :
623
624
625
626
627
The DL DCH SRB & HS-DSCH BLER should be equal to 0 on the UE simulator.
628
The UL PS SRB & EDCH BLER should be equal to 0 on the RNC simulator.
629
630
631
The UE simulator debug information should be consistent (MACESND logging window -> PDU
size, PDU Txed/ACK/NACK, BLER).
632
633
634
The call must be checked during 1 night (the AAL2 traffic should not be disrupted during the
night).
No alarm should be raised on the NodeB.
635
4.1.2.5.
636
MOBILITY TEST
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 32/174
637
638
639
Purpose:
640
641
Check that a complete procedure of softer handover from a cell supporting HSDPA service to a cell
supporting only R99 is successfully
642
Requirement:
643
644
Lamp connection
645
TM500 connection
646
The radio configuration in Daisy chain mode or STSRx+y mode or both mixed mode
647
Make sure two cells which will do the softer handover have the same frequency
648
Procedure:
649
650
651
Step3:add RL2 (DCH leg on the target cell) which is identical to the ADCH link
652
653
Step4:perform a SRLR procedure that will delete the HS-DSCH on the source cell and modify
associated parts of both legs to DCH
654
655
Expectable results:
656
657
Result1:all these procedures must be successful and the RL established in DCH on the target cell
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 33/174
658
659
660
Purpose:
661
662
Check that a complete procedure of softer handover from a cell in R99 to a cell supporting HSDPA is
successfully
663
Requirement:
664
665
Lamp connection
666
TM500 connection
667
The radio configuration in Daisy chain mode or STSRx+y mode or both mixed mode
668
Make sure two cells which will do the softer handover have the same frequency
669
Procedure:
670
671
672
673
674
Step4:perform a SRLR procedure that will reconfigure initial leg to an ADCH and the target leg to
HSDPA, adding the HSDSCH part
675
676
Expectable results:
677
678
Result1:all these procedures must be successful and the RL established in HSDPA on the target cell
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 34/174
679
680
4.1.2.6.
RADIATING
681
682
Purpose:
683
Check the radiating user interface on TIL displays and works correctly
684
685
686
687
688
Requirement:
1. Platform configuration applicable:
2. TIL connection
3. Spectrum analyzer connection at antenna output
4. The TIL is started and the BTS is not built.
689
Procedure:
690
691
692
693
694
Step 3:Configure the BTS with a downlink frequency value within the authorized range(Ndl = 5 Fdl, Ndl
= downlink frequency expressed as a number, Fdl = downlink frequency expressed in MHz)
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 35/174
BAND
I
II
IV
V
695
696
697
Step 5:Configure Max Trasmission Power, Primary Scrambling Code, Primary CPICH code, Priamry
SCH Power, Secondary SCH Power as the authorized range
698
699
Expectable results:
700
Check that the BTS resets in stand-alone mode when radiating mode is activated;;
701
702
Check Downlink Frequency, Max Trasmission Power, Primary Scrambling Code, Primary CPICH code,
Priamry SCH Power, Secondary SCH Power field could be edited
703
704
705
Check that RRH/TRDU cell could radiating successfully after activating radiating
Verify that the resulting spectrum corresponds to expected frequency and power levels displays
correctly on spectrum analyzer.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 36/174
706
707
708
Purpose:
709
Radiate the BTS in STSR1 configuration with upper limit of downlink frequency.
710
711
712
713
714
Requirement:
715
Procedure:
716
Step 1:The TIL is started and the BTS is starting in stand-alone mode and not built.
717
718
Step 2:Configure the BTS with the upper downlink frequency value referring to below table (Ndl = 5 Fdl,
Ndl = downlink frequency expressed as a number, Fdl = downlink frequency expressed in MHz).
1.
2.
3.
BAND
I
II
IV
V
719
720
Expectable results:
721
Check that the BTS resets in stand-alone mode when radiating mode is activated;
722
723
724
Verify that the resulting spectrum corresponds to expected frequency and power levels from CAP menu
and spectrum analyzer.
725
726
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 37/174
727
728
Purpose:
729
Radiate the BTS in STSR1 configuration with lower limit of downlink frequency.
730
731
732
733
734
Requirement:
735
Procedure:
736
Step 1:The TIL is started and the BTS is starting in stand-alone mode and not built.
737
738
Step 2:Configure the BTS with the lower downlink frequency value referring to below table (Ndl = 5 Fdl,
Ndl = downlink frequency expressed as a number, Fdl = downlink frequency expressed in MHz).
4.
5.
6.
BAND
I
II
IV
V
739
740
Expectable results:
741
Check that the BTS resets in stand-alone mode when radiating mode is activated;
742
743
744
Verify that the resulting spectrum corresponds to expected frequency and power levels from CAP menu
and spectrum analyzer.
745
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 38/174
746
747
748
Purpose:
749
The goal of this test case is to verify the RSSI reported at RRH/TRDU side is as expected at any case
750
Requirement:
751
752
753
Procedure:
754
755
Step1:thanks to Lamp, cellset without any signal injection, then Start the common measurement with
the command:Startcmeas cellid measurementid, check result1
756
Expectable results:
757
758
Result1:check RTWP reported on RRH/TRDU side and Lamp side, the RTWP
reported should around -106dbm
759
760
4.1.3.
ENDURANCE
761
4.1.3.1.
762
763
Purpose:
764
The purpose of this test is to check the robustness of the power off/on procedure of the BTS.
765
Requirements
766
767
2. OMC-B connection
768
3.
769
Step 1:
Power on Rack2u.
770
Step 2:
771
Step 3:
772
Step 4:
773
774
OAM EDURANCE
Lamp connection
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 39/174
775
776
Purpose:
777
The purpose of this test is to check the robustness of the reset procedure of the BTS.
778
Requirements
779
780
2. OMC-B connection
781
3.
Lamp connection
782
4.
783
784
785
Reset the BTS in the loop for n times and check whether BTS comes up fine and that radio resources
can be setup.
786
787
788
789
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 40/174
790
791
Purpose:
792
The purpose of this test is to check the robustness of the reset procedure of the slave RRH.
793
Requirements
794
795
2. OMC-B connection
796
3.
Lamp connection
797
4.
798
799
800
Reset the slave RRH in the loop for n times and check whether slave comes up fine and that radio
resources can be setup.
801
802
803
804
805
Purpose:
806
Purpose of the test is to test the stability of the BTS with continuous download of correct load.
807
Requirements
808
809
2. OMC-B connection
810
3.
Lamp connection
811
4.
812
5.
Generate a V5edX load where the TOKEN TYP is set to FFS in the FILE0.
813
6.
Generate a V5edY load where the TOKEN TYP is set to FFS in the FILE0.
814
7.
Generate a V5edZ load where the TOKEN TYP is set to FFS in the FILE0.
815
816
817
818
819
820
821
822
823
824
825
826
(* When the BTS restarts, the bootl3 detects that data partition is using FFS. This partition is formatted
in FFS. The content present in data partition is temporarily duplicated in RAM, before to be copy back
into data partition.)
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 41/174
827
4.1.3.2.
RADIO EDURANCE
828
829
Purpose:
830
831
Purpose of this test is to test the stability of BTS with the NUSCM command by setting the level 5 using
the lamp
832
Requirements
833
834
2.
Lamp connection
835
3.
836
From Lamp, use the ISS signal script and run the nuscm command for the level 5
837
838
839
Ensure that nuscm endurance run for at least 2 hours without any traps or abnormal behaviors on the
BTS
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 42/174
840
841
Purpose:
842
843
Purpose of this test is to test the stability of BTS with the ENDURO command by setting the level 5
using the lamp
844
Requirements
845
846
2.
Lamp connection
847
3.
848
849
850
From Lamp, use the ISS signal script and run the enduro command for the level 5
Ensure that enduro endurance run for at least 2 hours without any traps or abnormal behaviors on the
BTS
851
4.1.4.
852
4.1.4.1.
853
854
Purpose:
855
856
Check the NodeB starts correctly after power on for both Rack2U and ASB RRH, inhouse
RRH(2100MHz),TRDU,Adrew RRH
857
Requirement:
858
859
860
Procedure:
861
862
Step1:execute a Switch-off / Switch-on both RACK2U and ASB RRH, inhouse RRH(2100MHz),
TRDU,Adrew RRH,check result1
863
864
Step2:when Audit procedure is done, send commands from lamp in order to configure the Cells, Rach
and Fach channels on every RRH, check result2
865
Step3:send a Radio Link Setup command and every RRH, check result3
866
867
Expectable results:
868
Result1:when the NodeB is up, check the connection with OMC-B and lamp is done correctly
869
Result2:check cell setup response, Fachsetup response and Rachsetup response are successful
870
871
872
873
4.1.4.2.
874
875
Test label
29:AISG_TMA_START-UP_WITH-TMA-CONFIGURATION_BUT-NO-TMA
AISG-LITE
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 43/174
876
Purpose:
877
878
Requirement:
879
880
OMC-B connection
881
882
Procedure:
883
884
885
TmaAccessType :tmaUmtsOnly.
886
Check Result1.
887
4.1.4.3.
10/20KM FIBER
888
889
Purpose:
890
Check Rach Access and call setup could be successful with 10KM fiber connection
891
Requirement:
892
893
Lamp connection
894
TM500 connection
895
Procedure:
896
897
Step1:calculate the acceptable value of chip delay with 10km fiber, and assuming the propagation
speed over the fiber is 1.5 times slower than in the air. Formula as follows:
898
899
900
901
902
903
Step3:on TM500, set the parameter of setcellpathdelay x to the propagation delay near 192 chips on
script and then trigger the UL rach access
904
Step4:on Lamp side, type the command rachtest to accept the PRACH message part. Check Result1
-4
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 44/174
UBINETICS
Setup cell on cata
cellset 0
fachset 0
rachset 0
905
906
907
908
Step5:if Rach access is successful. And then setup a RL with the propagation delay received in
PRACH message part. Such as:rlset 0 1 amr_12k2_6 propdelay = 64 (In case of 20km fiber, propdelay
is 128), check Result 2
909
910
911
Expectable results:
Result1:lamp part could receive and show PRACH message part with propagation
delay around x/6
912
913
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 45/174
914
915
Purpose:
916
Check Rach Access and call setup could be successful with 20KM fiber connection on one chain.
917
Requirement:
918
919
Lamp connection;
920
TM500 connection;
921
922
Make sure the radio configuration in daisy chain mode, and the distance between dBTS and the last
RRH is 20km.
923
Procedure:
924
925
Step1:Calculate the acceptable value of chip delay with 20km fiber, and assuming the propagation
speed over the fiber is 1.5 times slower than in the air;
926
Formula as follows:
927
928
929
930
931
932
Step3:On TM500, set the parameter of setcellpathdelay x to the propagation delay near 384 chips on
script and then trigger the UL RACH access;
933
934
Step4:On Lamp side, type the command rachtest to accept the PRACH message part. Check
Result1;
UBINETICS
Setup cell on cata
cellset 0
fachset 0
rachset 0
935
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 46/174
936
937
938
Step5:If Rach access is successful. And then setup a RL with the propagation delay received in
PRACH message part. Such as:rlset 0 1 amr_12k2_6 propdelay = 128 (In case of 10km fiber,
propdelay is round 64), check Result 2.
939
940
Expectable results:
941
Result1:Lamp part could receive and show PRACH message part with propagation delay;
942
943
4.1.4.4.
6 CPRI LINK
944
945
Purpose:
946
947
The purpose of this test is to check that whether I &C RRH/TRDU type chould be changed and
displayed correctly on TIL according to ccm board type
948
Requirement:
949
950
TIL connection
951
952
Procedure:
953
954
955
956
Step2:select Display I&C parameters menuclick RRH/TRDU Tab, check the RRH/TRDU type
display correctly
957
958
Step3:select Change I&C parameters menuclick RRH/TRDU Tab, change the RRH/TRDU type to
HSSL, reset rack2u
959
960
Step4:select Change I&C parameters menuclick RRH/TRDU Tab, change the RRH/TRDU type to
CPRI, reset rack2u
961
962
963
964
965
Step2:select Display I&C parameters menuclick RRH/TRDU Tab, check the RRH/TRDU type
display correctly
966
967
Step3:select Change I&C parameters menuclick RRH/TRDU Tab, change the RRH/TRDU type to
HSSL, reset rack2u
968
969
Step4:select Change I&C parameters menuclick RRH/TRDU Tab, change the RRH/TRDU type to
CPRI, reset rack2u
970
971
Expectable results:
972
973
According to different hardware version for XCCMu, the mapping relation between I&C parameter and
link mode as following:
974
975
1W (old HW version):If the parameter value is 0, means link mode in optical 5, 6 is HSSL mode, else is
CPRI mode
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 47/174
976
977
0D (new HW version):If the parameter value is 0, means link mode in optical 4, 5, 6 is HSSL mode, else
is CPRI mode
978
So
979
980
981
982
983
Result2:RRH/TRDU type parameter can be changed to HSSL, and after rack2u reset and up, CPRI
RRH/TRDU on optical link 5, 6 can not be up normally, but CPRI RRH/TRDU on optical link 1,2,3,4
should be up normally
984
985
Result3:RRH/TRDU type parameter can be changed to CPRI, and after rack2u reset and up, all 6
CPRI RRH/TRDU can be up normally
986
987
988
989
990
991
Result2:RRH/TRDU type parameter can be changed to HSSL, and after rack2u reset and up, CPRI
RRH/TRDU on optical link 4, 5, 6 can not be up normally, but CPRI RRH/TRDU on optical link 1, 2, 3
should be up normally
992
993
Result3:RRH/TRDU type parameter can be changed to CPRI, and after rack2u reset and up, all 6
CPRI RRH/TRDU can be up normally
994
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 48/174
995
996
Test label
33:OAM_6_CPRI_LINK_DLU_CHECK_MAX_6_SECTORS_SUPPORTED
997
Purpose:
998
Configure file is checked during startup to make sure that max 6 sectors are supported
999
Requirement:
1000
1001
OMC-B connection
1002
Procedure:
1003
1004
1005
nbSector:7
1006
Sector [0]:
1007
AntennaAccessInstance
:0
1008
AntennaConnection
:11/1011
1009
1010
Sector [5]:
1011
AntennaAccessInstance
:0
1012
AntennaConnection
:61/1061
1013
1014
1015
RemoteRadioHead [0]:
1016
remoteRadioHeadInstance
1017
1018
RemoteRadioHead [5]:
1019
remoteRadioHeadInstance
:11/1011
:61/1061
1020
1021
1022
1023
nbSector:6
1024
1025
nbRemoteRadioHead:6
1026
1027
1028
Expectable results:
1029
1030
Result1:after Rack2u startup, BTS will be in BULD KO state, type emo->ala>chk, error information will
show for reason that max 6 remote sectors supported
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 49/174
1031
1032
Result2:new antennaAccessInstance 41, 51, 61 or 1041, 1051, 1061 could be accepted, cofigure file is
built. If 6 RRHs/TRDUs connected, all local cell status should be enabled
1033
1034
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 50/174
1035
1036
1037
Purpose:
1038
Configure file is checked during startup to make sure that max 12 cells are supported
1039
Requirements:
1040
1041
OMC-B connection
1042
Procedure:
1043
1044
6 sectors:
1045
1046
nbSector:6
1047
Sector [0]:
1048
AntennaAccessInstance
:0
1049
AntennaConnection
:11/1011
1050
1051
Sector [5]:
1052
AntennaAccessInstance
:0
1053
AntennaConnection
:61/1041
1054
1055
1056
remoteRadioHead [0]:
1057
remoteRadioHeadInstance
1058
1059
remoteRadioHead [5]:
1060
remoteRadioHeadInstance:61/1061
1061
13 cells:
1062
1063
nbBtsCell:13
1064
btsCell [0]:
1065
LocalCellId
1066
1067
1068
:11/1011
:191
btsCell [12]:
LocalCellId
:303
1069
1070
1071
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 51/174
1072
1073
1074
nbBtsCell:12
btsCell [12]:
LocalCellId
:303
1075
1076
1077
Expectable results:
1078
1079
Result1:after Rack2u startup, cofigure file is not built, type emo->ala>chk, error information will show
for reason that max 12 cells supported with 6 sectors
1080
1081
Result2:cofigure file is built without error. If 6 RRHs/TRDUs connected, all local cell status should be
enabled
1082
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 52/174
1083
1084
Purpose:
1085
1086
The purpose of this test is to check that TIL can be connected to Rack2u & RRH and that visual check
is correct on the Graphical User Interface under 6 cpri link.
1087
Requirement:
1088
1089
2. TIL connection
1090
1091
The figure below describes the GUI expected on the TIL if a xCOB is inserted in the rack.
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 53/174
1104
1105
1106
This window presents the same information for Optical interfaces and all RRHs on the link (only one for
star configuration). Contextual menus are available when clicking on those objects:
1107
1108
1109
1110
1111
For the RRH, interface is similar to the information available in contextual menus for FTR boards.
1112
1113
- Alarms
1114
1115
1116
1117
1118
- Reset
, OI2 ,OI3,OI4,OI5,OI6 are powered off (the popup menu command becomes
1119
1120
1121
1122
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 54/174
1123
- RRH alarms
1124
1125
1126
- Stop Tx emission
x is powered off (the popup menu command becomes Run Tx emission)
1127
1128
1129
1130
1131
- Marking
1132
1133
1134
1135
- Alarms
1136
1137
1138
1139
- Reset
1140
1141
Expectable results:
1142
TIL:
1143
TIL is connected.
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
- Green:unlocked
1154
- Orange:Locked
1155
1156
- Green:No alarm
1157
1158
1159
1160
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 55/174
1161
- Green:ON:Laser is powered.
1162
- White:OFF:Laser is unpowered
1163
1164
1165
- Number of RRH on the link (1 on the picture) is not required for star configurations.
1166
1167
1168
1169
1170
1171
- Green:xCOB unlocked
1172
- Orange:xCOB Locked
1173
- Alarm status
1174
- Green:OK:xCOB is ok
1175
- Red:Alarm:xCOB is in alarm
1176
1177
- Green:ON:Laser is powered.
1178
- White:OFF:Laser is unpowered
1179
OMC-B:
1180
1181
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
01.01/EN
Preliminary
24/Sep/2014
Page 56/174
1183
Purpose:
1184
1185
The purpose of this test is to check that Rack2U & RRH visual display correctly on the OMCB
Graphical User Interface under 6 cpri link.
1186
Requirements:
1187
1188
2. OMC-B connection
1189
Procedure:
1190
1191
Expectable results:
1192
1193
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 57/174
4.1.4.5.
POWER POOLING
1196
1197
Test label
37:POWER_POOLING_CHANGE_THE_POWER_OF_EACH_FREQUENCY
1198
Purpose:
1199
1200
Check the PA allows some overbooking of the power of the carrier where HSDPA/E-DCH is
deployed over the carrier where legacy R99 is deployed
R99
F2 max power
R99
Maximum PA Power
F1 max power
Power
not used
F2 max power
Maximum power
HSDPA
F1 max power
R99 &
GBR
R99 &
GBR
HSDPA
1201
1202
Requirement:
1203
1204
Lamp is connected
1205
1206
1207
Configuration:
1208
Currently only support STSR-2 with only maximum 1 carrier per PA with HSDPA activated
1209
1210
Set paPoolingActivation=True
1211
1212
Procedure:
1213
Step1:setup both HSDPA cell and R99 cell with Lamp, check result1
1214
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 58/174
Step3:remove the R99 cell with Reproxy commands since Lamp is no more available
1216
CellDelete
1217
Linkid
:1 to 6
1218
Reuid
:1 to 1
1219
LocalCellId
1220
Check result3
1221
Step4:remove the HSDPA cell and Setup the R99 cell with Reproxy commands
1222
1223
1224
1225
Check result4
1226
Expectable results:
1227
1228
1229
Result1:check HSDPA cell is setup with CPICH/MaxPower=35.1/45.1 dBm, and R99 cell is
setup with CPICH/MaxPower=33.0/43.0 dBm. Although MaxPower together is greater than
46.0 dBm, no alarm reported and both cell established successfully
1230
1231
Result2:check UDT script is running successfully. Then check the total power of both HSDPA
cell and R99 cell. HSDPA cell should be 43.9 dBm, and R99 cell should be 41.9 dBm
1232
1233
Result3:check the R99 cell is removed, and total power of HSDPA cell changes to 45.1dBm
dynamically
1234
1235
1236
Result4:check the HSDPA cell is removed, and total power of R99 cell changes to 43.0 dBm
dynamically
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 59/174
1245
1246
1247
1248
1249
1250
Purpose:
Power polling is failed with HSDPA on both 2 carriers
Requirement:
STSR2
2UV2P2+6*RRH/2UV2P2+6*TRDU
The two cells can be setup
Procedure:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 60/174
4.1.5.
1254
4.1.5.1.
1255
1256
Purpose:
1257
1258
This test is to check the message exchange between new RRH and Reproxy when it is
plugged into the chain as the last RRH
1259
Requirement:
1260
1261
1262
Procedure:
1263
1264
Step2:open terminal tool, telnet to CCM board.Open the trace "/lib_cpri/oem_lib_cpri> Trace"
1265
1266
1267
Expectable results:
1268
1269
1270
1271
Result2:check that the Reuid in RE_GetAlarm_Indication message from first RRH should be
correct
1272
1273
Result3:within 100 seconds, RE_GetAlarm_Report (Alarm Master Port=ON) for the last RRH
can be seen soon from. Or last RRH startup failed
1274
1275
1276
Result4:check that the Reuid in RE_GetAlarm_Report message from last RRH should be
correct
LINK STATUS
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 61/174
1279
Purpose:
1280
1281
This test is to check the message exchange between last RRH and Reproxy when it is plugged
out from the fiber chain
1282
Requirement:
1283
1284
1285
Procedure:
1286
1287
1288
1289
1290
Expectable results:
1291
1292
1293
1294
1295
Result2:check that the Reuid in RE_GetAlarm_Indication message should be the one of RRH
(n-1)
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 62/174
4.1.5.2.
LOOP BACK
1298
1299
Purpose:
1300
1301
This test is to validate the digital transmission on RRH in Loopback mode after connecting the
NodeB to the RRHs
1302
Requirement:
1303
1304
1305
TIL connected
1306
1307
Lamp is connected
1308
TM500 is connected
1309
Procedure:
1310
1311
Step1:open TIL, select one RRH in one fiber chain, send a cpri loopback test (loopback in
RRH) command, check Result1
1312
Step2:redo the test steps on the other RRHs in the same chain
1313
1314
Step4:setup cell and call via lamp and TM500, check Result2
1315
Expectable results:
1316
1317
1318
Result2:NodeB startup successfully, cell configuration and call setup is successful now
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 63/174
4.1.5.3.
ALARM
1321
1322
Purpose:
1323
1324
This test is to check the Master link error alarm when RRH L1/L2 error is detected on RRH
master port. If RRH to be tested is the last one in fiber chain, no Master link error reported
1325
Requirement:
1326
1327
1328
TIL connected
1329
OMCB connected
1330
Procedure:
1331
1332
1333
Step2:plug out fiber from master port of RRHn (RRHn is not the last one in this chain) in the
fiber chain
1334
1335
Step3:check downstream RRHs status and the result from bci command, TIL and OMC-B,
check Result1~Result4
1336
Step4:plug in fiber to this RRHn, check TIL, OMC-B and NodeB status, and check Result5
1337
1338
Expectable results:
1339
1340
Result1:the Master Link Error alarm from RRHn is shown with the bci command emo/alarm>
GlobalAlarms
1341
Result2:alarm is shown in TIL terminal with link error daisy chain segment alarm description
1342
Result3:alarm is shown in OMCB with link error daisy chain segment alarm description
1343
1344
Result4:all the downstream RRHs will be reset, RRH objects in TIL and OMC-B will be
deleted
1345
1346
Result5:all RRH objects plugged in will be created in TIL and OMC-B, NodeB will work
smoothly
1347
1348
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 64/174
4.1.5.4.
PLUG IN/OUT
1351
1352
Purpose:
1353
1354
Check the cells are correctly configured when RRHx in the chain is plugged out/plugged in at
any time
1355
Requirement:
1356
1357
1358
1359
1360
1361
Procedure:
1362
1363
Step1:plug-out the optical fiber of RRHx(x = 1 n, 1<n<=6), type auditrequest on lamp then
check Result1
1364
1365
Step3:Setup cells and make calls on RRHx or its downstream RRHs. Check Result3
1366
1367
Step4:repeat step1 ~ step3 with Next RRHx+1, till to the last RRHn in the chain. Check
Result4
1368
Expectable results:
1369
Result1:
1370
1371
Audit Response message raised to the lamp excludes cells of all downstream RRHx
and itself
1372
1373
Check RRHx object and the downstream RRH objects dont appear any more on the
OMC-B
1374
Result2:
1375
RRHx and all its downstream RRHs in this chain will reset
1376
1377
Type auditrequest on lamp then check Audit Response message raised to the lamp
includes cells of all downstream RRHx and itself
1378
Check RRHx object and the following RRHs objects appear again on the OMC-B
1379
1380
1381
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 65/174
4.1.5.5.
SW UPGRADE
1384
1385
Purpose:
1386
1387
Check RRHs in the same chain with correct version, no need to update SW, these RRHs will
startup successfully and twice reset will not happen
1388
Requirement:
1389
1390
1391
1392
Procedure:
1393
1394
Step2:ensure all RRHs with correct SW version, that is consistant with NodeB package
1395
1396
Step3:plug all RRHs in NodeB with Daisy Chain mode, then power on NodeB and to observe
the status of all RRHs. check Result1
1397
Step4:setup cells and voice call in these RRHs in the same chain. Check Result2
1398
Expectable results:
1399
Result1:all RRHs in this chain will do nothing. RRHs Reset will not happen
1400
1401
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 66/174
1404
Purpose:
1405
1406
Check the daisy chain RRH2 upgrade scenario when RRH1 has the correct SW version but
RRh2 has outdated SW version
1407
1408
Requirement:
1409
1410
1411
RRH1 has correct SW version with NodeB package, but RRH2 has outdated one
1412
1413
Procedure:
1414
1415
1416
1417
Step4:repeat Step1, and plug in RRH3 during RRH2 is downloading, check Result4
1418
Expectable results:
1419
1420
1421
Result3:RRH2 reset again and till startup successfully. Its SW version is the same as RRH1
1422
1423
1424
Result4:after download is finished, RRH2 and RRH3 reset once, and it with correct SW
version after startup
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 67/174
1427
Purpose:
1428
Check the daisy chain RRH upgrade scenario that requested by OMC-B
1429
Requirement:
1430
1431
1432
1433
Prepare two different NodeB loads that it include different RRH SW version
1434
Procedure:
1435
1436
Step1:NodeB and RRHs in Daisy Chain mode work smoothly with SW version A, check
Result1
1437
1438
1439
Expectable results:
1440
Result1:NodeB and all RRHs work smoothly in Daisy Chain with SW version A
1441
1442
Result2:NodeB and all RRHs work smoothly in Daisy Chain with SW version B
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 68/174
4.1.5.6.
DOWNLOAD
1445
1446
Purpose:
1447
Check the impact that power off the platform when downloading SW for a new plug-in RRH
1448
Requirement:
1449
1450
1451
1452
Procedure:
1453
1454
1455
1456
Expectable results:
1457
Result1:D2U and all other RRHs in Daisy Chain are not impact
1458
1459
1460
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 69/174
4.1.5.7.
START-UP
1463
1464
Purpose:
1465
1466
Check the impact for downstream RRHs after RRH (n-1) Power on/Power off and not any
impact for upstream RRHs
1467
Requirement:
1468
1469
1470
1471
Procedure:
1472
Step1:power off RRH (n-1), not the 1st RRH and not the last one, then check Result1
1473
Expectable results:
1474
1475
1476
Result1:after step1, RRH (n) will reset autonomously in 5 seconds, and every 5 seconds later,
the next RRH will reset automonously. This action will repeat to the last RRH
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 70/174
1479
Purpose:
1480
It is configured as normal mode in DLU; add new RRH downstream doesnt impact the call
1481
Requirement:
1482
1483
1484
Procedure:
1485
1486
1487
1488
Step4:add a downstream RRH to this RRH (master port for RRH11 is enable), check Result4
1489
1490
Expectable results:
1491
1492
1493
1494
1495
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 71/174
4.1.5.8.
RESET
1498
1499
Purpose:
1500
1501
Check after RRH (n) reset by CPRI_L1_Reset, RRH (n) and all the downstream RRHs should
be reset. And all upsteam RRHs are not impact
1502
Requirement:
1503
1504
1505
1506
Procedure:
1507
1508
Step1:reset RRH1 by CPRI_L1_Reset via bci command /pltf/cpri> ResetRE, then give
related link ID
1509
1510
1511
1512
Step3:reset RRH (n) which is not 1st RRH and not last one by Re_Reset_Request
(REid=Next_re) via bci command /reproxy/HardResetNextRE, then give related ID. Check
Result2
1513
Expectable results:
1514
1515
1516
1517
Result2:the RRH (n) and all downstream RRHs will reset, and all upstream RRHs are not
impact
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 72/174
1520
Purpose:
1521
Check RRH (n) will reset after lock/unlock RRH (n) by OMC-B
1522
Requirement:
1523
1524
1525
D2U NodeB and all RRH in Daisy Chain work smoothly and connect to OMC-B
1526
Procedure:
1527
1528
1529
Expectable results:
1530
1531
1532
Result1:after step 2, RRH (n) will reset, but no any impact tofor other RRH (Include upstream
RRHs and downstream RRHs) in the chain
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 73/174
1535
Purpose:
1536
1537
Requirement:
1538
1539
1540
1541
Procedure:
1542
1543
Expectable results:
1544
1545
1546
Result1:all RRH in the chain will reset, the platform will startup smoothly, including NodeB and
all RRHs in the chain
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 74/174
1549
Purpose:
1550
1551
Requirement:
1552
1553
1554
1555
1556
Procedure:
1557
1558
Expectable results:
1559
Result1:after step 1, the RRH will be reset, and it can be startup normally
1560
1561
1562
Result2:this RRH reset will not impact any other RRH in same fiber chain, including
downstream RRHs and upstream RRHs
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 75/174
4.1.5.9.
CELL PROCEDURE
1565
1566
Purpose:
1567
1568
The purpose of this test is to check that whether NodeB can setup the cell successfully on
RRHs which are on the same or different chain
1569
Requirement:
1570
1571
1572
Procedure:
1573
1574
Step2:delete cells
1575
Expectable results:
1576
1577
1578
Result2:type in cap/ctx/cell/Detail on CCM, check whether includes the info of cells which is
created by lamp, and other cells information is OK
1579
1580
1581
Result3:after cell is setup successfully, check the Tx frequency and channel power indicated
in PSA are consistent with the ones in lamp
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 76/174
1584
Purpose:
1585
1586
The purpose of this test is to check that whether NodeB can delete the cell correctly on RRHs
which are on the same or different chain
1587
Requirement:
1588
1589
1590
Procedure:
1591
1592
Step1:setup cells in each RRH from lamp. Make sure the cell setup successfully. Check
Result 1
1593
1594
1595
1596
Expectable results:
1597
1598
Result1:after cell is setup successfully, check the Tx frequency and channel power indicated
in PSA are consistent with the ones in lamp
1599
1600
1601
1602
4.1.5.10.
1603
1604
Purpose:
1605
1606
Check that the plug-in and plug-out activities of a new RRH (with different load) will not impact
to the existing calls
1607
Requirement:
1608
1609
1610
1611
1612
1613
Procedure:
1614
1615
Step2:plug-in the optical fiber of a new RRH (with different load), check Result1
1616
1617
Step3:after 3 minutes, plug-out the optical fiber of a new RRH (with different load), check
Result2
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 77/174
Step4:repeat step1 ~ step3 with Next RRHx+1, till to the last RRHn in the chain. Check
Result3
1620
Expectable results:
1621
Result1:
1622
1623
1624
Result2:
1625
1626
1627
1628
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 78/174
1631
Purpose:
1632
Check that the call is still successful when SW reset the upstream RRH.
1633
1634
1635
1636
Requirement:
1637
Procedure:
1638
Step 1:NodeB and all RRHs are start-up with the correct NodeB package;
1639
1640
1641
Expectable Results:
1642
1643
1644
1645
Result 2:RRH1 will be OK after SW reset, and the amr call on RRH2 is still running
successfully.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 79/174
4.1.6.
1648
4.1.6.1.
1649
1650
Purpose:
1651
1652
The purpose of this test is to check that NodeB with STSRx+y configuration in normal mode
can be startup successfully
1653
Requirement:
1654
1655
1656
1657
Procedure:
1658
Step1:power on NodeB with all of RRHs, open the CCM trace, and check Result1&2
1659
Expectable results:
1660
START-UP
1661
1662
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1663
1664
1665
1666
Result2:after NodeB startup successfully, cell and basic call should be setup successfully
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 80/174
1669
Purpose:
1670
1671
The purpose of this test is to check that NodeB with STSRx+y configuration in degrade mode
can be startup successfully
1672
Requirement:
1673
1674
1675
1676
Procedure:
1677
Step1:power on NodeB with main RRH, open the CCM trace, and check Result1&2&4
1678
1679
Expectable results:
1680
1681
1682
1683
1684
1685
1686
1687
daisy chain mode:upstream RRHs of this main RRH are startup successfully, and
downstream RRHs are not startup
1688
1689
1690
1691
daisy chain mode:only Tx and Rx path for the upstream RRHs are enable, no this
paired RRH
1692
1693
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 81/174
4.1.6.2.
PLUG IN/OUT
1696
1697
Purpose:
1698
1699
The purpose of this test is to check the correct configuration when plug out/in main or div RRH
at any time
1700
Requirement:
1701
1702
1703
1704
Procedure:
1705
Step1:power on NodeB with both main and div RRH. Check Result1&4
1706
1707
1708
Expectable results:
1709
1710
1711
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1712
1713
1714
1715
Result2:check the Tx and Rx path by typing emo/bts on CCM, the behaviour is different
according to the topology:
1716
1717
star mode:if plug out the main RRH, only Tx and Rx path for div RRH are enable; if
plug out div RRH, only Tx and Rx path for main RRH are enable
1718
1719
1720
daisy chain mode:if plug out the main RRH, only Tx and Rx path for the upstream
RRHs are enable; if plug out div RRH, Tx and Rx path for main RRH and upstream
RRHs are enable
1721
Result3:after RRH startup successfully, check Tx and Rx path of all the RRHs are all enable
1722
1723
Result4:after NodeB startup successfully, cell and basic call should be setup successfully
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 82/174
1726
Purpose:
1727
1728
The purpose of this test is to check the correct configuration when plug in div/main RRH with
different load
1729
Requirement:
1730
1731
1732
1733
Procedure:
1734
Step1:main or div RRH in the paired RRH is plugged in, and the other is not
1735
1736
1737
Expectable results:
1738
1739
1740
1741
1742
1743
Result2:check the Tx and Rx path by typing emo/bts on CCM, the behavior is different
according to the topology:
1744
1745
1746
star mode:if div RRH is plug in and main RRH is not, only Tx and Rx path for div RRH
are enable; if main RRH is plug in and div RRH is not, only Tx and Rx path for main
RRH are enable
1747
1748
1749
daisy chain mode:if main RRH is not plug in, only Tx and Rx path for the upstream
RRHs are enable; if div RRH is not plug in, Tx and Rx path for main RRH and
upstream RRHs are enable
1750
1751
1752
star mode:this RRH will upgrade to the same load with the RRH which is already
plug-in, after this RRH reset, Tx and Rx path of all the RRHs are all enable
1753
1754
daisy chain mode:this RRH and the downstream RRHs will upgrade and reset, then
all the Tx and Rx path are enable
1755
1756
Result4:after NodeB startup successfully, cell and basic call should be setup successfully
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 83/174
4.1.6.3.
RESET
1759
1760
Purpose:
1761
1762
Requirement:
1763
1764
1765
1766
Procedure:
1767
Step1:power on NodeB with both main and div RRH. Check Result1&5
1768
1769
1770
Expectable results:
1771
1772
1773
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1774
1775
1776
1777
1778
Result2:check the Tx and Rx path by typing emo/bts on CCM, when main RRH is resetting,
Tx and Rx path for main RRH are disable; after main RRH startup successfully, Tx and Rx
path of main RRH are enable
1779
1780
1781
Result3:check the Tx and Rx path by typing emo/bts on CCM, when div RRH is resetting, Tx
and Rx path for div RRH are disabled; after div RRH startup successfully, Tx and Rx path of
div RRH are enable
1782
1783
1784
Result4:if it is in daisy chain mode, this RRH reset will not impact any other RRH in same fiber
chain, including downstream RRHs and upstream RRHs. If in star mode, this RRH reset will
not impact any other RRH
1785
1786
Result5:after NodeB startup successfully, cell and basic call should be setup successfully
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 84/174
1789
Purpose:
1790
1791
Requirement:
1792
1793
1794
1795
Procedure:
1796
Step1:power on NodeB with both main and div RRH. Check Result1&4
1797
1798
1799
Expectable results:
1800
1801
1802
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1803
1804
1805
1806
1807
Result2:check the Tx and Rx path by typing emo/bts on CCM, when main RRH is resetting,
Tx and Rx path for main RRH are disable; after main RRH startup successfully, Tx and Rx
path of main RRH are enable
1808
1809
1810
Result3:check the Tx and Rx path by typing emo/bts on CCM, when div RRH is resetting, Tx
and Rx path for div RRH are disabled; after div RRH startup successfully, Tx and Rx path of
div RRH are enable
1811
1812
1813
Result4:if it is in daisy chain mode, this RRH reset will not impact any other RRH in same fiber
chain, including downstream RRHs and upstream RRHs. If in star mode, this RRH reset will
not impact any other RRH
1814
1815
Result5:after NodeB startup successfully, cell and basic call should be setup successfully
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 85/174
4.1.6.4.
OMC-B OPERATION
1818
1819
Purpose:
1820
1821
Check that if antennaConnectionId of any one RRH is not null, antennaConnectionId of all
others should not be null
1822
1823
1824
1825
1826
Requirement:
1827
1828
1829
1830
Procedure:
1831
Step1:power on NodeB with both main and div RRH. Check Result1
1832
1833
Step2:after NodeB get a full starup, through OMC-B, antennaConnectionId in one RRH has a
correct value and in other RRH does not present, then rebuild. Check Result2
1834
1835
Step3:after NodeB get a full starup, through OMC-B, antennaConnectionId in one RRH has a
special value which does not in any AntennaAccess, then rebuild. Check Result3
1836
1837
Step4:after NodeB get a full starup, through OMC-B, antennaConnectionId in three RRH has
the same value, then rebuild. Check Result4
1838
1839
Step5:after NodeB get a full starup, through OMC-B, rxCabling in AntennaAccess is set to
mainInputOnly, then rebuild. Check Result5
1840
Expectable results:
1841
1842
1843
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1844
1845
1846
Result2:
1847
1848
1849
1850
1851
In OMC-B, there is the alarm "INVALID CONFIGURATION DATA", in Addtional Test there is
the alarm description Not Exist Antenna Connection.
1852
Result3:
1853
1854
1855
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 86/174
1857
1858
In OMC-B, there is the alarm "INVALID CONFIGURATION DATA", in Addtional Test there is
the alarm description RRH Not Present In Antenna Access.
1859
Result4:
1860
1861
1862
1863
1864
1865
In OMC-B, there is the alarm " CONFIGURATION FILE INCONSISTENT WITH HARDWARE ",
in Addtional Test there is the alarm description Too many RRH in AntennaAccess.
1866
Result5:
1867
1868
1869
1870
1871
1872
In OMC-B, there is the alarm " INVALID CONFIGURATION DATA ", in Addtional Test there is
the alarm description RxCabling type out of range.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 87/174
4.1.6.5.
CELL PROCEDURE
1875
1876
Purpose:
1877
1878
Requirement:
1879
1880
1881
1882
Procedure:
1883
Step1:power on NodeB with both of main and div RRH. Check Result1
1884
1885
Step2:setup cells in main and div RRH from lamp, for example cell1 in main RRH and cell7 in
div RRH. Check Result2&3&4
1886
Step3:delete cells
1887
1888
Expectable results:
1889
1890
1891
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1892
1893
1894
1895
1896
Result3:after cells setup successfully, telnet to main and div RRH, use commands
fcpcTipTxFreqDataShow and fcpcTipRxFreqDataShow, check:
1897
1898
in main RRH, for cell1, both Tx and Rx carrier are exist; for cell7, only Rx carrier is
exist
1899
in div RRH, for cell7, both Tx and Rx carrier are exist; for cell1, only Rx carrier is exist
1900
1901
1902
Result4:after cell is setup successfully, check the Tx frequency and channel power indicated
in PSA are consistent with the ones in lamp
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 88/174
1905
Purpose:
1906
1907
Requirement:
1908
1909
1910
If in daisy chain mode, do not plug out main RRH in any paired RRH
1911
1912
Procedure:
1913
1914
Step1:power on NodeB with one RRH (RRH1) of any paired RRH (RRH1+RRH2), meet
requirement3. Check Result1
1915
1916
1917
Step4:delete cell
1918
Expectable results:
1919
1920
1921
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path of
RRH1 are enable
1922
1923
1924
1925
1926
1927
1928
1929
1930
Result4:after cell is setup successfully, check the Tx frequency and channel power indicated
in PSA are consistent with the ones in lamp
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 89/174
1933
Purpose:
1934
Check that cell delete scenario is correct when STSRx+y configuration in normal mode
1935
Requirement:
1936
1937
1938
1939
Procedure:
1940
Step1:power on NodeB with both main and div RRH. Check Result1
1941
1942
Step2:setup cells in main and div RRH respectively from lamp, for example cell1 in main RRH
and cell7 in div RRH. Check Result2
1943
1944
1945
Expected results:
1946
1947
1948
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1949
1950
1951
1952
1953
1954
Result4:after cell1 is deleted successfully, telnet to main and div RRH, and use commands
fcpcTipTxFreqDataShow and fcpcTipRxFreqDataShow to check:
1955
in main RRH, only Rx carrier for cell7 is exist, no other carrier information
1956
in div RRH, only Tx and Rx carrier info for cell7 are exist, no carrier info for cell1
1957
1958
1959
1960
Result5:after cell7 is deleted successfully, telnet to main and div RRH, use commands
fcpcTipTxFreqDataShow and fcpcTipRxFreqDataShow to check no carrier info exist on
both paired RRH
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 90/174
1963
Purpose:
1964
1965
Requirement:
1966
1967
1968
1969
Procedure:
1970
Step1:power on NodeB with both main and div RRH. Check Result1
1971
1972
Step2:setup cells in main and div RRH from lamp, for example cell1 in main RRH and cell7 in
div RRH. Check Result2
1973
1974
Step3:reset main RRH from TIL, check Result3&4&5. (Note:reset div RRH could have the
similar result as main RRH.)
1975
Step4:delete cells
1976
Expectable results:
1977
1978
1979
type emo/bts, check that MIBState is Build, CheckDLU is OK. Tx and Rx path are
all enable
1980
1981
1982
1983
1984
Result3:after main RRH is startup successfully, telnet to main and div RRH, and use
commands fcpcTipTxFreqDataShow and fcpcTipRxFreqDataShow to check:
1985
in main RRH, only Rx carrier for cell7 is exist, no other carrier information
1986
in div RRH, only Tx and Rx carrier info for cell7 are exist, no carrier info for cell1
1987
Result4:after NodeB startup successfully, basic call can be setup in cell7 successfully
1988
1989
1990
Result5:if in daisy chain mode, this RRH reset will not impact any other RRH in same fiber
chain, including downstream RRHs and upstream RRHs
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 91/174
4.1.6.6.
1993
1994
Purpose:
1995
Check the correct behaviour with/without TMA equipment and with/without TMA configuration
1996
Requirement:
1997
1998
1999
2000
Procedure:
2001
2002
2003
2004
TMA MANAGEMENT
Sector [0]:
2005
AntennaAccessInstance
2006
AntennaConnection
2007
TmaAccessType
:0
:11
:1
2008
2009
2010
2011
2012
Sector [0]:
2013
AntennaAccessInstance
2014
AntennaConnection
2015
TmaAccessType
:0
:11
:1
2016
2017
2018
Step7:configure no TMA access in DLU by OMC-B, for example, TMA hasnt been configured
in AntennaConnection11
2019
Sector [0]:
2020
AntennaAccessInstance
2021
AntennaConnection
2022
TmaAccessType
:0
:11
:0
2023
2024
Expectable results:
2025
2026
Result1:after NodeB is starting up, TMA alarm on main RRH will be reported to TIL and
OMC-B, and no TMA alarm in div RRH.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 92/174
2029
Result3:
2030
2031
2032
In CCM trace, check TmaAccessReq, if using inhouse RRH, main RRH is in TMA Umts
mode and div RRH is in TMA Mix mode; if using TRDU, both main and div RRH are in TMA
Umts mode
2033
2034
2035
In lamp, typing auditrequest, the maxpower for cells in this antennaAccess is decreased. The
descreased value is 3.5 dB which means 35 should be descreased from original value. For
example, the maxpower is 430 without TMA, and it changed to 395 with TMA.
2036
2037
Result4:check NodeB could startup normally without alarm and error. Telnet to CCM, type
emo/bts, check that local cells configured in AntennaConnection11 are enabled
2038
2039
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 93/174
4.1.6.7.
FAULT MANAGEMENT
2042
2043
Purpose:
2044
2045
Requirement:
2046
2047
2048
2049
Procedure:
2050
2051
2052
Step3:
2053
RRH-ih:click the mode to ON, select the alarm Tx VSWR Level 2 Alarm, check Result1
2054
2055
Step4:RRH-ih:stop other alarms, click the mode to ON, select the alarm Tx VSWR Alarm,
check Result2
2056
2057
2058
Step6:RRH-ih:stop other alarms, click the mode to ON, select the alarm Tx VSWR Level 2
Alarm, check Result3
2059
2060
Step7:RRH-ih:stop other alarms, click the mode to ON, select the alarm Tx VSWR Alarm,
check Result5
2061
Note, refer to the latest TRDU alarm document for TRDU VSWR alarm
2062
Expectable results:
2063
2064
2065
From CCM trace, type /emo/alarm> GlobalAlarms, and RRH VSWR MAIN can be found for
main RRH;
2066
2067
2068
Result2:From CCM trace, type /emo/alarm> GlobalAlarms, and RRH VSWR MAIN can be
found for main RRH;
2069
2070
2071
2072
From CCM trace, type /emo/alarm> GlobalAlarms, and RRH VSWR DIV can be found for
main RRH;
2073
2074
2075
Result5:From CCM trace, type /emo/alarm> GlobalAlarms, and RRH VSWR DIV can be
found for main RRH;
2076
2077
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 94/174
4.1.6.8.
COMMON MEASUREMENT
2080
2081
Purpose:
2082
Test the stability of NodeB with the startcmeas command including all measurement types
2083
Requirement:
2084
2085
2086
Procedure:
2087
2088
2089
2090
Step2:set up cell and start common measurement for both transmit carrier power and receive
carrier power, keep this test continuously running at least 12 hours without any traps or
abnormal behaviors on the NodeB, check Result1
2091
Expectable results:
2092
2093
2094
2095
If value of Received Total Wide-band Power (RTWP) is between 60 and 65, the test
result is acceptable. If it is too high or too low, the test result is abnormal.
(RTWP(dBm)=RTWP value * 0.1 + (-112) )
2096
(dBm=10log(mw))
2097
2098
2099
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 95/174
4.1.6.9.
DELAY MANAGEMENT
2102
2103
Purpose:
2104
Test whether the delay management of NodeB is correct in STSRx+y normal mode.
2105
Requirement:
2106
2107
2108
2109
2110
Procedure:
2111
2112
2113
2114
Expectable results:
2115
2116
Result2:the delay value should be changed, but the local cells operational state is still ok
2117
2118
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 96/174
UL delay value is an alignment of main and div Rx delay, it nearly equal to 1792.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 97/174
4.1.7.
2123
2124
NOTE:In following test cases, we will encounter some cases that NOT have enough capacity
license. In this condition, it will follow these rules to confirm which cell is enabled.
2125
2126
2127
2128
2129
Third, for the same LCG priority, the same frequencies rank in their sector => sort by LCG Id
2130
Fourth, for the same LCG, the same frequencies rank in their sector => sort by Local CellId
2131
2132
Purpose:
2133
Verify the 2nd carrier Capacity License usage when the license is increased
2134
Requirement:
2135
NodeB is startup
2136
2137
2138
rrhCarrierCapacityLicensing = 0
2139
2140
2141
Procedure:
2142
2143
2144
2145
2146
2147
2148
2149
Expectable results:
2150
2151
2152
nd
2153
2154
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 98/174
2156
2157
2158
2159
2160
2161
2162
2163
2164
2165
2166
2167
2168
2169
2170
2171
Result5:check that there is no change; cells on all 2nd carriers are enabled
2172
2173
2174
2175
2176
2177
Result6:using the menu RTC => PM => FastClock:A => Display in a telnet console, check that
the
2178
2179
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 99/174
Test label
74:Capacity_Licensing_rrhCarrierCapacityLicensing_Decrease
2183
Purpose:
2184
2185
Requirement:
2186
NodeB is startup
2187
2188
2189
rrhCarrierCapacityLicensing = infinite
2190
2191
Procedure:
2192
2193
2194
2195
2196
2197
2198
2199
Expectable results:
2200
2201
2202
2203
2204
2205
2206
Result4:the NodeB should reset. Check that two cells on 2 carrier are disabled
2207
2208
nd
nd
2209
2210
2211
Result5:the NodeB should reset. Check that all the cells on all 2nd carrier are disabled
2212
2213
2214
2215
2216
2217
Result6:using the menu RTC => PM => FastClock:A => Display in a telnet console, check that
the
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 100/174
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 101/174
4.1.8.
FRS 34396
2222
2223
Purpose:
2224
2225
Requirement:
2226
2227
Procedure:
2228
2229
2230
Step3:setup one or more cells on both of the Main RRH and Diversity RRH
2231
2232
2233
Expectable results:
2234
Result1:while all cells in one RRH were deleted, this RRH would be powered off automatically
2235
Result2:the delay time that RRH power off after cell delete is more than 120s
2236
Result3:compare the power when cell set up with the power RRH power off
2237
2238
4.1.8.1.
2239
2240
Purpose:
2241
2242
Requirement:
2243
2244
NodeB is connected.
2245
Procedure:
2246
On TIL, turn on/off led via RRH or NodeB(OP: It decides by the RRH and NodeB architecture.).
2247
2248
2249
2250
2251
Expectable results:
2252
Purpose:
2253
Check LED status of ASB RRH via telnet to ASB RRH from Ethernet port.
2254
Check LED status of ASB RRH via telnet to ASB RRH from D2U.
2255
Requirement:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 102/174
2257
Procedure:
2258
2259
2260
2. Telnet to RRH via Ethernet port to check the LED status with command of
ledTipMlDisplayState, Check Result1;
2261
2262
3. Telnet to RRH via D2U to check the LED status with command of
ledTipMlDisplayState, Check Result1;
2263
Expectable results:
2264
Result1: The LED status should be correct with current RRH status.
2265
2266
2267
4.1.8.2.
2268
2269
Purpose:
2270
2271
Requirement:
2272
2273
Procedure:
VSWR
2274
2275
2276
2. Telnet to RRH via Ethernet port or D2U to check the LED status with command of
ledTipMlDisplayState, Check Result1;
2277
Expectable results:
2278
2279
Result1: From the trace of RRH, the VSWR measurement report should
be report every 2s.
2280
2281
2282
Purpose:
2283
2284
Requirement:
2285
2286
Procedure:
2287
2288
2289
Expectable results:
2290
2291
2292
Result1: From the trace of RRH and trace of D2U, the VSWR alarm report
D2U within 10s.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 103/174
2294
Purpose:
2295
2296
2297
2298
2.
TIL connection
2299
3.
OMCB connection
2300
4.
2301
Procedure:
2302
2303
2304
Step3:Cell delete;
2305
2306
2307
Expectable results:
2308
2309
2310
2311
Purpose:
2312
2313
2314
Check TX VSWR level 2 alarm will report if RRH with 4db attenuation and short cut connector
at the antenna
2315
2316
2.
TIL connection
2317
3.
OMCB connection
2318
4.
2319
Procedure:
2320
Step1:Add 4db attenuation and short cut connector at the RRH antenna
2321
2322
2323
2324
Expectable results:
2325
2326
After several minutes VSWR level 2 medium alarm will report to TIL and OMCB, RRH in
degrade status
2327
2328
2329
VSWR measurement values display on OCI(ASB RRH local maintence tool) should be
correctly
Requirements:
Requirements:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 104/174
2332
Purpose:
2333
2334
2335
Check TX VSWR level 3 alarm will report if RRH with 1db attenuation and short cut connector
at the antenna
2336
2337
2.
TIL connection
2338
3.
OMCB connection
2339
4.
2340
Procedure:
2341
Step1:Add 1db attenuation and short cut connector at the RRH antenna
2342
2343
2344
2345
Expectable results:
2346
2347
After several minutes VSWR level 3 major alarm will report to TIL and OMCB, RRH in broken
status
2348
Cell will be down (RSI will send to lamp to indicate the impacted cell)
2349
2350
VSWR measurement values display on OCI(ASB RRH local maintence tool) should be
correctly
Requirements:
2351
2352
4.1.8.3.
SINGLE RX PORT
2353
2354
Purpose:
2355
2356
2357
2358
2. TIL connection
2359
3. OMCB connection
2360
2361
2362
Procedure:
2363
2364
2365
2366
2367
Purpose:
Requirements:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 105/174
Check that a complete procedure of softer handover from a cell supporting HSDPA service to
a cell supporting only R99 is successfully
2370
Requirement:
2371
2372
Lamp connection
2373
TM500 connection
2374
The radio configuration in Daisy chain mode or STSRx+y mode or both mixed mode
2375
Make sure two cells which will do the softer handover have the same frequency
2376
2377
Procedure:
2378
2379
2380
Step3:add RL2 (DCH leg on the target cell) which is identical to the ADCH link
2381
2382
Step4:perform a SRLR procedure that will delete the HS-DSCH on the source cell and modify
associated parts of both legs to DCH
2383
2384
2385
4.1.8.4.
2386
2387
In this section, it describe all external alarm that simulate it with external alarm board. For ASB
RRH, maybe we need .
2388
2389
2390
Purpose:
2391
Check that the External Alarms can be reported to TIL and OMCB correctly.
2392
2393
2394
2395
2396
Requirement:
2397
Procedure:
2398
Step 1:
2399
Step 2:
TIL connection
OMCB connection
External Alarm Board
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 106/174
2400
2401
Step 3:
Press the button for each different External Alarm on external alarm board.
2402
Step 4:
2403
Step 5:
2404
Step 6:
2405
Expectable results:
2406
2407
2408
Step 4: All the 6 External Alarms can be displayed in TIL corresponding to the External alarm
board. External alarms will report to OMCB correctly also.
Step 6: After rack2u reset, external alarm still report to OMCB and TIL correctly
2409
4.1.8.5.
2410
2411
In this section, it describe all internal alarm that simulate it with OCI tools. For ASB RRH,
maybe no OCI tools to trigger these alarms. We can trigger it with command of ASB RRH.
Reset Rack2u
Check the alarm information from TIL and OMCB.
2412
2413
2414
Purpose:
2415
2416
2417
2418
2419
2420
2421
2422
Requirement:
Platform configuration applicable:
TIL connection
OMCB connection
OCI Tool
Procedure&Expected Results:
Refer to test label
Slave Link Low Optical Signal Level_ASB RRH
Slave Link Loss of Framing (LOF) _ASB RRH
Slave Link Loss of Signal (LOS) _ASB RRH
Slave Link Port Transceiver Failure_ASB RRH
Slave Link Remote Alarm Indication (RAI) _ASB RRH
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 107/174
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 108/174
Test label 87: Slave Link Low Optical Signal Level_ASB RRH
2425
Purpose:
2426
2427
This test is to report alarm when received optical signal on the slave (upstream)
link port is unexpectedly low, though communication is still possible.
2428
2429
2430
2431
2432
Requirement:
2433
2434
Select the related alarm Slave Link Low Optical Signal Level in the RRH/Procedures,
2435
2436
Then check the result from RTC and TIL and OMC-B
2437
TIL connection
OMCB connection
OCI Tool
2438
2439
2440
2441
2442
2443
Alarm Type
Alarm Severity
alarm
informantion
LED exptected
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 109/174
Medium
Flash
Yellow,
Flash Green
2444
2445
2446
Purpose:
2447
2448
2449
This test is to report alarm when locally-detected slave link port alarm, framing
cannot be recovered at the slave link port. This alarm is enabled only after the
link has first been established.
2450
2451
2452
2453
2454
Requirement:
2455
2456
2457
2458
Then check the result from RTC and TIL and OMC-B
2459
2460
2461
2462
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 110/174
2464
2465
Alarm Type
Alarm Severity
Major
alarm
informantion
LED exptected
Flash
Yellow,
Flash Green
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 111/174
Test label 89: Slave Link Loss of Signal (LOS) _ASB RRH
2467
Purpose:
2468
2469
2470
This test is to report alarm when locally-detected slave link port alarm, no
signal is detected at the slave link port. This alarm is enabled only after the link
has first been established.
2471
2472
2473
2474
2475
Requirement:
2476
2477
2478
2479
Then check the result from RTC and TIL and OMC-B
2480
TIL connection
OMCB connection
OCI Tool
2481
2482
2483
2484
2485
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 112/174
Alarm Type
Alarm Severity
alarm
informantion
Major
LED exptected
Flash
Yellow,
Flash Green
2487
2488
2489
Purpose:
2490
2491
This test is to report alarm when slave link optical transceiver has failed and
communication to the REC is probably not available
2492
2493
2494
2495
2496
Requirement:
2497
2498
Select the related alarm Slave Link Port Transceiver Failure in the RRH/Procedures,
2499
2500
Then check the result from RTC and TIL and OMC-B
2501
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 113/174
2502
2503
2504
2505
2506
2507
Alarm Type
Alarm Severity
alarm
informantion
Major
LED exptected
Red
2508
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 114/174
Test label 91:Slave Link Remote Alarm Indication (RAI) _ASB RRH
Purpose:
2511
2512
This test is to report alarm when one or more of the incoming slave link LOS,
LOF, or RAI bits is set.
2513
2514
2515
2516
2517
Requirement:
2518
2519
Select the related alarm Slave Link Remote Alarm Indication (RAI) in the RRH/Procedures,
2520
2521
Then check the result from RTC and TIL and OMC-B
2522
2523
2524
2525
2526
2527
2528
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 115/174
Alarm Type
Alarm Severity
Major
alarm
informantion
LED exptected
Slave Link
RemoteAlarm
Indication (RAI)
Flash
Yellow,
Flash Green
2529
2530
2531
Test label 92: Master Link Low Optical Signal Level_ASB RRH
Purpose:
2532
2533
This test is to report alarm when received optical signal on the slave (upstream)
link port is unexpectedly low, though communication is still possible.
2534
2535
2536
2537
2538
Requirement:
2539
2540
Select the related alarm Master Link Low Optical Signal Level in the RRH/Procedures,
2541
2542
Then check the result from RTC and TIL and OMC-B
2543
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 116/174
2544
2545
2546
2547
2548
2549
Alarm Type
Alarm Severity
Medium
alarm
informantion
LED exptected
Master Link
Low Optical
Signal Level
Flash
Yellow,
Flash Green
2550
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 117/174
Test label 93: Master Link Loss of Framing (LOF) _ASB RRH
Purpose:
2553
2554
2555
This test is to report alarm when locally-detected master link port alarm,
framing cannot be recovered at the master link port. This alarm is enabled only
after the link has first been established.
2556
2557
2558
2559
2560
Requirement:
2561
2562
2563
2564
Then check the result from RTC and TIL and OMC-B
2565
2566
2567
2568
2569
2570
2571
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 118/174
Alarm Type
Alarm Severity
alarm
informantion
LED exptected
Master Link
Flash
Loss of Framing Yellow,
(LOF)
Flash Green
Major
2572
2573
Test label 94: Master Link Loss of Signal (LOS) _ASB RRH
2574
Purpose:
2575
2576
2577
This test is to report alarm when locally-detected master link port alarm, no
signal is detected at the master link port. This alarm is enabled only after the
link has first been established.
2578
2579
2580
2581
2582
Requirement:
2583
2584
2585
2586
Then check the result from RTC and TIL and OMC-B
2587
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 119/174
2588
2589
2590
2591
2592
2593
Alarm Type
Alarm Severity
Major
alarm
informantion
LED exptected
Master Link
Loss of Signal
(LOS)
Flash
Yellow,
Flash Green
2594
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 120/174
2596
Purpose:
2597
2598
This test is to report alarm when master link optical transceiver has failed and
communication to the REC is probably not available
2599
2600
2601
2602
2603
Requirement:
2604
2605
Select the related alarm Master Link Port Transceiver Failure in the RRH/Procedures,
2606
2607
Then check the result from RTC and TIL and OMC-B
2608
2609
2610
2611
2612
2613
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 121/174
Alarm Type
Alarm Severity
alarm
informantion
Master Link
Port
Transceiver
Failure
Major
LED exptected
Red
2615
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 122/174
Test label 96: Master Link Remote Alarm Indication(RAI) _ASB RRH
2617
Purpose:
2618
2619
This test is to report alarm when one or more of the incoming slave link LOS,
LOF, or RAI bits is set.
2620
2621
2622
2623
2624
Requirement:
2625
2626
Select the related alarm Master Link Remote Alarm Indication (RAI) in the RRH/Procedures,
2627
2628
Then check the result from RTC and TIL and OMC-B
2629
TIL connection
OMCB connection
OCI Tool
2630
2631
2632
2633
2634
2635
Alarm Type
Alarm Severity
alarm
informantion
LED exptected
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 123/174
Master Link
Remote Alarm
Indication (RAI)
Major
Flash
Yellow,
Flash Green
2636
2637
2638
Purpose:
2639
2640
This test is to report alarm when there have been no management messages
received in the past 30 seconds, or there is no active C&M TCP connection.
2641
2642
2643
2644
2645
Requirement:
2646
2647
2648
2649
Then check the result from RTC and TIL and OMC-B
2650
TIL connection
OMCB connection
OCI Tool
2651
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 124/174
2653
2654
2655
2656
17
Alarm Type
Alarm Severity
Communication
Error
Medium
alarm
informantion
Communication
Failure
LED exptected
Flash
Yellow,
Flash Green
2657
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 125/174
2659
Purpose:
2660
2661
The RRH is report alarm when below its normal operating temperature but still
capable of transmitting.
2662
2663
2664
2665
2666
Requirement:
2667
2668
2669
2670
Then check the result from RTC and TIL and OMC-B
2671
2672
2673
2674
2675
2676
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 126/174
18
Alarm Type
Alarm Severity
Temperature
Alarm
Medium
alarm
informantion
LED exptected
Under
Temperature
Green,Flash
Red
2678
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 127/174
2680
Purpose:
2681
2682
The RRH is report alarm when below its normal operating temperature but still
capable of transmitting.
2683
2684
2685
2686
2687
Requirement:
2688
2689
2690
2691
Then check the result from RTC and TIL and OMC-B
2692
2693
2694
2695
2696
2697
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 128/174
2699
ASSOCIATED CRPI GENERIC ALARM
Alarm Id
19
Alarm Type
Alarm Severity
alarm
informantion
LED exptected
Temperature
Alarm
Major
Warm-up
Flash Red
2700
2701
2702
Purpose:
2703
2704
The RRH is report alarm when RRH temperature is rising near the shutdown
limit.
2705
2706
2707
2708
2709
Requirement:
2710
2711
2712
2713
Then check the result from RTC and TIL and OMC-B
2714
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 129/174
2715
2716
2717
2718
2719
2720
20
Alarm Type
Alarm Severity
alarm informantion
LED
exptected
Temperature
Alarm
Medium
Over
Green,Flash
Temperature-Warning Red
2721
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 130/174
2723
Purpose:
2724
2725
The RRH is report alarm when the RRH temperature is above operating range,
and the transmitter has shut down to attempt to reduce the temperature.
2726
2727
2728
2729
2730
Requirement:
2731
2732
2733
2734
Then check the result from RTC and TIL and OMC-B
2735
2736
2737
2738
2739
2740
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 131/174
21
Alarm Type
Alarm Severity
alarm informantion
LED
exptected
Temperature
Alarm
Major
Over
Flash Red
Temperature-Critical
2742
2743
2744
Purpose:
2745
2746
The RRH is report alarm when at least one failure was detected during power
on self test, but the unit may still be functional, though in a degraded state.
2747
2748
2749
2750
2751
Requirement:
2752
2753
Select the related alarm Self Test Partial Failure in the RRH/Procedures,
2754
2755
Then check the result from RTC and TIL and OMC-B
2756
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 132/174
2757
2758
2759
2760
2761
2762
Alarm Type
Alarm Severity
alarm
informantion
Medium
LED exptected
Red,Green
2763
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 133/174
2765
Purpose:
2766
2767
2768
The RRH is report alarm when the power-on self test detected a critical failure
that prevents the RRH from transmitting. The RRH must be reset to unlatch
this alarm.
2769
2770
2771
2772
2773
Requirement:
2774
2775
Select the related alarm Self Test Critical Failure in the RRH/Procedures,
2776
2777
Then check the result from RTC and TIL and OMC-B
2778
TIL connection
OMCB connection
OCI Tool
2779
2780
2781
2782
2783
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 134/174
Alarm Type
Alarm Severity
alarm
informantion
Self Test
Critical Failure
Major
LED exptected
Red
2785
2786
2787
Purpose:
2788
2789
2790
The RRH is report alarm when FPGA download failures, or PLLs are not
locked. Note that this is evaluated during initialization and the unit is never
enabled. The RRH must be reset to unlatch this alarm.
2791
2792
2793
2794
2795
Requirement:
2796
2797
2798
2799
Then check the result from RTC and TIL and OMC-B
2800
TIL connection
OMCB connection
OCI Tool
2801
2802
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 135/174
2804
2805
2806
Alarm Type
26 PLL Failure
Alarm Severity
alarm
informantion
Initialization
Failure
Major
LED exptected
Red
2807
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 136/174
2809
Purpose:
2810
2811
2812
The RRH is report alarm when Indicates general software failures, including
TCP/IP stack errors or TCP/IP Allocate Packet errors.This alarm remains
asserted for a minimum of 30 seconds.
2813
2814
2815
2816
2817
Requirement:
1. Platform configuration applicable:
2. TIL connection
3. OMCB connection
4. OCI Tool
2818
2819
2820
2821
8. Then check the result from RTC and TIL and OMC-B
2822
2823
2824
2825
2826
2827
2828
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 137/174
Alarm Type
Alarm Severity
27 Software Failure
Minor
alarm
informantion
LED exptected
Software
Failure
Green,Flash
Red
2829
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written
authorization
UMT/BTS/DJD/024788
V01.01/EN
Standard
04/12/2014
Page 138/174
2831
Purpose:
2832
The RRH is report alarm when the number of EVENT messages exceeds threshold.
2833
2834
2835
2836
2837
Requirement:
2838
2839
2840
2841
Then check the result from RTC and TIL and OMC-B
2842
TIL connection
OMCB connection
OCI Tool
2843
2844
2845
2846
2847
2848
Alarm Type
Alarm Severity
alarm
informantion
LED exptected
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 139/174
28
Communication
Error
Message
Throttling
Minor
Green,Flash
Red
2849
2850
2851
Purpose:
2852
2853
The RRH is report alarm when any error is dectected on the Radio Receiver
side(channelizer,synthetiser..)
2854
2855
2856
2857
2858
Requirement:
2859
2860
2861
2862
Then check the result from RTC and TIL and OMC-B
2863
TIL connection
OMCB connection
OCI Tool
2864
2865
2866
2867
2868
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 140/174
Alarm Type
31 Rx Path Failure
Alarm Severity
alarm
informantion
LED exptected
Major
Receiver Fail
Red
2870
2871
2872
Purpose:
2873
2874
2875
2876
2877
2878
Requirement:
2879
2880
2881
2882
Then check the result from RTC and TIL and OMC-B
2883
2884
2885
2886
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 141/174
2888
2889
32
Alarm Type
Alarm Severity
Gain Control
Alarm
Medium
alarm
informantion
Gain Control
Warning
LED exptected
Flash
Red,Flash
Green
2890
2891
2892
Purpose:
2893
The RRH is report alarm when any error is dectected on the Radio Transmitter side
2894
2895
2896
2897
2898
Requirement:
2899
2900
2901
2902
Then check the result from RTC and TIL and OMC-B
2903
TIL connection
OMCB connection
OCI Tool
2904
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 142/174
2906
2907
2908
2909
Alarm Type
Alarm Severity
33 Tx Path Failure
alarm
informantion
Transmitter
Failure
Major
2910
2911
2912
Purpose:
2913
2914
2915
2916
2917
2918
Requirement:
2919
2920
2921
2922
Then check the result from RTC and TIL and OMC-B
2923
LED exptected
Red
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 143/174
2924
2925
2926
2927
2928
2929
2930
ASSOCIATED CRPI GENERIC ALARM
Alarm Id
34
Alarm Type
Alarm Severity
Gain Control
Alarm
Major
alarm
informantion
Gain Control
Failure
2931
2932
2933
Purpose:
2934
2935
2936
2937
2938
2939
Requirement:
2940
LED exptected
Red
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 144/174
2942
2943
Then check the result from RTC and TIL and OMC-B
2944
2945
2946
2947
2948
2949
2950
Alarm Type
Alarm Severity
35 RF Signal Alarm
alarm
informantion
RF Output
Overdrive
Major
2951
2952
2953
Purpose:
2954
LED exptected
Flash Red
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 145/174
Requirement:
2960
2961
2962
2963
Then check the result from RTC and TIL and OMC-B
2964
TIL connection
OMCB connection
OCI Tool
2965
2966
2967
2968
2969
2970
2971
ASSOCIATED CRPI GENERIC ALARM
Alarm Id
Alarm Type
Alarm Severity
36 Rx Path Failure
alarm
informantion
Receiver 1
Failure
Medium
LED exptected
Red,Green
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 146/174
2974
Purpose:
2975
2976
2977
2978
2979
2980
Requirement:
2981
2982
2983
2984
Then check the result from RTC and TIL and OMC-B
2985
2986
2987
2988
2989
2990
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 147/174
Alarm Type
Alarm Severity
37 Rx Path Failure
alarm
informantion
Receiver 2
Failure
Medium
2992
2993
2994
Purpose:
2995
2996
2997
2998
2999
3000
Requirement:
3001
3002
3003
3004
Then check the result from RTC and TIL and OMC-B
3005
LED exptected
Red,Green
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 148/174
3006
3007
3008
3009
3010
3011
3012
ASSOCIATED CRPI GENERIC ALARM
Alarm Id
Alarm Type
38 Low rssi
Alarm Severity
alarm
informantion
Diversity
Imbalance
Minor
3013
3014
3015
Purpose:
3016
3017
3018
3019
Requirement:
LED exptected
Flash
Red,Flash
Green
TIL connection
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 149/174
OMCB connection
OCI Tool
3022
3023
3024
3025
Then check the result from RTC and TIL and OMC-B
3026
3027
3028
3029
3030
3031
3032
3033
ASSOCIATED CRPI GENERIC ALARM
Alarm Id
Alarm Type
Alarm Severity
40 Hareware Failure
alarm
informantion
Equipment
Failure
Major
LED exptected
Red
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 150/174
3036
Purpose:
3037
3038
3039
3040
3041
3042
Requirement:
3043
3044
3045
3046
Then check the result from RTC and TIL and OMC-B
3047
3048
3049
3050
3051
3052
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 151/174
Alarm Type
Alarm Severity
41 DC Voltage Alarm
alarm
informantion
Input Voltage
Failure
Major
3054
3055
3056
Purpose:
3057
3058
3059
3060
3061
3062
Requirement:
3063
3064
3065
3066
Then check the result from RTC and TIL and OMC-B
3067
LED exptected
Flash Red
TIL connection
OMCB connection
OCI Tool
3068
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 152/174
3070
3071
3072
3073
Alarm Type
Alarm Severity
42 DC Voltage Alarm
alarm
informantion
Power
Converter
Failure
Major
3074
3075
3076
Purpose:
3077
3078
3079
3080
3081
3082
Requirement:
3083
3084
3085
3086
Then check the result from RTC and TIL and OMC-B
3087
LED exptected
Red
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 153/174
3088
3089
3090
3091
3092
3093
Alarm Type
Alarm Severity
44 Software Failure
C&M Timer
Expired
Major
3094
3095
3096
Purpose:
3097
3098
3099
3100
3101
3102
Requirement:
3103
alarm
informantion
LED exptected
Red
TIL connection
OMCB connection
OCI Tool
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 154/174
3105
3106
Then check the result from RTC and TIL and OMC-B
3107
3108
3109
3110
3111
3112
3113
3114
ASSOCIATED CRPI GENERIC ALARM
Alarm Id
Alarm Type
47 PLL Failure
Alarm Severity
alarm
informantion
LED exptected
Major
Clock Failure
Flash Red
3115
3116
3117
Purpose:
3118
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 155/174
Requirement:
3124
3125
3126
3127
Then check the result from RTC and TIL and OMC-B
3128
TIL connection
OMCB connection
OCI Tool
3129
3130
3131
3132
3133
3134
Alarm Type
48 PLL Failure
Alarm Severity
alarm
informantion
RF Synthesizer
Failure
Major
LED exptected
Flash Red
3135
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 156/174
3137
Purpose:
3138
3139
3140
3141
3142
3143
Requirement:
3144
3145
3146
3147
Then check the result from RTC and TIL and OMC-B
3148
3149
3150
3151
3152
3153
3154
TIL connection
OMCB connection
OCI Tool
3155
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 157/174
Alarm Type
Alarm Severity
49 Hareware Failure
alarm
informantion
Digital Input
Overdrive
Medium
LED exptected
Flash Red
3156
3157
Test label 122: Simulate all ASB RRH internal alarms at the same time
3158
Purpose:
3159
3160
Check Rack2u could process and report alarms normally without error when all RRH internal alarms
report at the same time
3161
3162
3163
3164
3165
Requirement:
3166
3167
3168
3169
Then check the result from RTC and TIL and OMC-B
3170
3171
Rack2u could process and report alarms normally without error and reset
3172
4.1.8.6.
3173
3174
3175
3176
3177
3178
3179
3180
3181
Step1:Configure PaRatio parameters per cell(same sector) from 50%-50% to 20%-80%, check Result
1
3182
3183
3184
3185
3186
Result1: D2U should startup successfully, the new paratio parameters should be taken into consider
after rack2u is up
3187
Result2: Cellset, fachset, rlset per carrier should be successful, call could be made successfully
3188
3189
3190
TIL connection
OMCB connection
OCI Tool
Purpose:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 158/174
4.1.8.7.
AC POWER TEST
3193
3194
3195
3196
3197
3198
3199
Procedure:
3200
3201
3202
3203
3204
3205
3206
3207
3208
4.1.8.8.
3209
3210
3211
3212
3213
Typical power consumption shall be less than as shown in the table below. Percentages are different
RF output levels relative to the max 60W. No more than 8% is allowed for the AC version than DC
version.
Purpose:
Purpose:
Percentage
DC Power Consumption
AC Power Consumption
20%(12W)
135W
145.8W
50%(30W)
185W
199.8W
100%(60W)
Requirement:
260W
280.8W
3214
3215
3216
3217
3218
3219
Step2: Setup cell and radiolinks to make RF output reach 20%(12W), check Result 1
3220
Step3: Setup cell and radiolinks to make RF output reach 50%(30W), check Result 2
3221
Step4: Make RF full output 100% with UDT scripts, check Result 3
3222
3223
Step5: Configure platform with AC power, STSR1, max power 60W, repeat step 2~step 4
Expectable results:
3224
Result1: RRH power consumption should be no more than Row 2 in the table.
3225
Result2: RRH power consumption should be no more than Row 3 in the table.
3226
Result3: RRH power consumption should be no more than Row 4 in the table.
3227
3228
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 159/174
3231
3232
3233
3234
3235
3236
3237
Step1: Configure platform with DC power, STSR4, max power 15W for each carrier.
3238
3239
3240
Step2: Make RF full output 100% with UDT scripts, check Result 1
Expectable results:
Result1: RRH power consumption should be no more than 300W.
3241
4.1.9.
Purpose:
AISG FULL
3242
3243
Purpose:
3244
3245
3246
1, Platform is available
3247
2, RET is available
3248
3, TIL is connected
3249
4, OMC-B is connected
3250
Procedure:
3251
3252
3253
Result:
3254
3255
3256
Result2: RET can be scanned and the information is correct.(check the info is
consistent to TIL)
3257
3258
3259
Purpose:
3260
3261
3262
1, Platform is available
3263
2, TMA is available
3264
3, TIL is connected
3265
4, OMC-B is connected
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 160/174
3266
3267
3268
3269
3270
3271
3272
Result2: TMA can be scanned and the information is correct (check the info is
consistent to TIL).
3273
3274
3275
4.1.9.1.
RESET
3276
3277
Purpose:
Check device can be reset by OMC-B successfully. (aisgDeviceReset?)
3278
Requirement:
3279
3280
1, Platform is available
3281
3282
3, TIL is connected
3283
4, OMC-B is connected
Procedure:
3284
Step1: Reset Aisg including TMA and RET device from OMCB.
3285
Result:
3286
3287
3288
3289
4.1.9.2.
DEVICE DATA
3290
3291
Purpose:
3292
3293
3294
1, Platform is available
3295
2, RET is available
3296
3, TIL is connected
3297
Procedure:
3298
3299
Step2: open TIL and set device data for RET, check Result2.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 161/174
3300
3301
3302
3303
3304
3305
Purpose:
Check device data for TMA can be set successfully.
3306
Requirement:
3307
3308
1, Platform is available
3309
2, TMA is available
3310
3, TIL is connected
Procedure:
3311
3312
3313
Step2: open TIL and set device data for TMA, check Result2.
Result:
3314
3315
3316
3317
3318
4.1.9.3.
UPLOAD
3319
3320
Purpose:
3321
3322
Check the configure file upload to the RRH from TIL would be supported.
Requirement:
3323
1, Platform is available
3324
3325
3, TIL is connected
3326
4, OMC-B is connected
3327
Procedure:
3328
Step1: NodeB startup with RET and TMA connected to RRH, check Result1.
3329
3330
3331
Step3: fill the username, password, file needs to be uploaded, as well as the remote
directory, select upload, check Result2.
3332
Step4: get RET and TMA info from TIL, check Result3.
3333
Step5: get RET and TMA info from OMC-B, check Result4.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 162/174
3334
3335
3336
3337
3338
Result3: the info got form TIL is consistent with the configure file which has been
uploaded.
3339
3340
Result4: the info got form OMC-B is consistent with the configure file which has been
uploaded.
3341
3342
4.1.9.4.
TILT
3343
3344
Purpose:
3345
3346
3347
1, Platform is available
3348
2, RET is available
3349
3, TIL is connected
3350
4, OMC-B is connected
3351
Procedure:
3352
3353
3354
Step2: open TIL, double click RRH, right click and select AISG -> Set Tilt, set the
value beyond the range, check Result1.
3355
3356
3357
Result:
3358
3359
3360
Result3: The Tilt value is consistent with the value which has been set in TIL.
3361
3362
3363
Purpose:
3364
3365
3366
1, Platform is available
3367
2, RET is available
3368
3, TIL is connected
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 163/174
4, OMC-B is connected
Procedure:
3371
3372
3373
Step2: open TIL, double click RRH, right click and select AISG -> Calibrate Tilt,
check Result1.
3374
3375
Result:
3376
3377
Result2: The Tilt value is consistent with the value which has been calibrated in TIL.
3378
3379
3380
Purpose:
3381
3382
3383
1, Platform is available
3384
2, RET is available
3385
3, OMC-B is connected
3386
Procedure:
3387
3388
3389
3390
Result:
Result1: Tilt value can be got correctly.
3391
3392
3393
Purpose:
3394
3395
3396
1, Platform is available
3397
2, RET is available
3398
3, OMC-B is connected
3399
Procedure:
3400
3401
3402
3403
Result:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 164/174
3405
3406
3407
3408
Purpose:
Check Tilt can be calibrated by OMC-B correctly.
3409
Requirement:
3410
3411
1, Platform is available
3412
2, RET is available
3413
3, TIL is connected
3414
4, OMC-B is connected
Procedure:
3415
3416
3417
3418
3419
3420
3421
3422
Result3: The Tilt value is consistent with the value which has been calibrated.
3423
3424
4.1.9.5.
TMA
3425
3426
Purpose:
3427
3428
3429
1, Platform is available
3430
2, TMA is available
3431
3, TIL is connected
3432
4, OMC-B is connected
3433
Procedure:
3434
3435
3436
Step2: open TIL, double click RRH, right click and select AISG -> Get/Set TMA Gain,
select Reload to set the TMA parameters, check Result1.
3437
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 165/174
3440
3441
Result2: The TMA gain got form OMC-B is consistent with the value set in TIL.
3442
3443
3444
Purpose:
3445
3446
3447
1, Platform is available
3448
2, TMA is available
3449
3, TIL is connected
3450
4, OMC-B is connected
3451
Procedure:
3452
3453
3454
3455
Result:
3456
3457
Result2: The TMA gain got form TIL is consistent with the value set in OMC-B.
3458
3459
3460
Purpose:
3461
3462
3463
1, Platform is available
3464
3465
3, TIL is connected
3466
4, OMC-B is connected
3467
Procedure:
3468
3469
3470
3471
Result:
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 166/174
3473
Result2: the TMA mode got from OMC-B is the value which has been set.
3474
3475
4.1.9.6.
ABNORMAL CASES
3476
3477
Purpose:
3478
3479
Check ALD info does not change after hot plug out before scan.
Requirement:
3480
1, Platform is available
3481
3482
3, TIL is connected
3483
4, OMC-B is connected
3484
Procedure:
3485
3486
3487
Step3: open TIL/OMC-B, get inventory/device data/Tilt info/TMA info, check Result1.
3488
3489
3490
Step5: open TIL, double click RRH, right click and select AISG -> Scan bus, check
Result3.
3491
Step6: open TIL/OMC-B, get inventory/device data/Tilt info/TMA info, check Result4.
3492
3493
Result:
3494
Result1: the info for the ALD which has been plugged out still exists.
3495
3496
Result3: scan info is correct and no info for the ALD which has been plugged out.
3497
Result4: no info for the ALD which has been plugged out.
3498
3499
3500
3501
Purpose:
3502
3503
Check ALD info does not change after hot plug in before scan.
Requirement:
3504
1, Platform is available
3505
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 167/174
3, TIL is connected
3507
4, OMC-B is connected
Procedure:
3508
3509
3510
3511
Step3: open TIL/OMC-B, get inventory/device data/Tilt info/TMA info, check Result1.
3512
3513
3514
Step5: open TIL, double click RRH, right click and select AISG -> Scan bus, check
Result3.
3515
Step6: open TIL/OMC-B, get inventory/device data/Tilt info/TMA info, check Result4.
3516
3517
3518
Result1: no info for the ALD which has been plugged in.
3519
3520
Result3: scan info includes the info for the ALD which has been plugged in.
3521
Result4: the info for the ALD which has been plugged in is correct.
3522
3523
3524
3525
3526
4.2
PowerSaving Feature
3527
4.2.1
3528
3529
3530
3531
3532
3533
3534
Test Label: 143 SETUP/DELETE ONE CELL ON 21C RRH WITH ASB PA VENDOR
Purpose:
Checking setup/delete one cell with different power on 21C RRH with ASB PA Vendor.
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
Lamp and omcb connection
3535
3536
3537
3538
Procedure:
Configure cell parameter as below:
3539
3540
3541
3542
In
Lamp
file:
configure
MAXDLPOWER
(unit=0.1dBm)
as
300(1W)/369(5W)/400(10W)/417(15W)/430(20W)/444(28W)/447(30W)/454(35W)/460(
40W)/465(45W)/469(50W)/471(52W)/477(60W) respectively.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 168/174
1. Setup the cell and make a R99 call on this cell. Check result 1.
3544
3545
3546
3547
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
2. Cell is delete and no power output anymore.
3548
3549
3550
4.2.2
3551
3552
3553
3554
3555
3556
3557
Test Label: 144 SETUP/DELETE TWO CELLS ON 21C RRH WITH ASB PA VENDOR
Purpose:
Checking setup/delete two cells with different power on 21C RRH with ASB PA vendor.
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
Lamp and omcb connection
3558
3559
3560
Procedure:
Configure cell parameter as below:
3561
3562
3563
In Lamp file: For 2 cell, configure (cell1, cell2) MAXDLPOWER (unit=0.1dBm) as (300,
400)/(400, 400)/(417, 430)/(430, 430)/(447, 447) respectively.
3564
3565
3566
3567
3568
3569
3570
3571
3572
Check result 1.
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
3573
3574
3575
3576
3577
3578
3579
3580
4.2.3
Test Label: 145 SETUP/DELETE THREE CELLS ON 21C RRH WITH ASB PA VENDOR
Purpose:
Checking setup/delete three cells with different power on 21C RRH with ASB PA vendor.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 169/174
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
Lamp and omcb connection
Procedure:
Configure cell parameter as below:
3587
3588
3589
In Lamp file: For 3 cell, configure (cell1, cell2, cell3) MAXDLPOWER (unit=0.1dBm) as
(300, 400, 400)/(400,400,400)/(417, 430, 430)/(430, 430,430) respectively.
3590
1. Setup the cell and make a R99 call on cell1. Check result 1.
3591
3592
3593
3594
3595
3596
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
3597
3598
3599
3600
3601
4.2.4
3602
3603
3604
3605
3606
3607
3608
3609
Test Label: 146 SETUP/DELETE THREE CELLS ON 21C RRH WITH ASB PA VENDOR
3610
3611
3612
Procedure:
Purpose:
Checking setup/delete four cells with different power on 21C RRH with ASB PA vendor.
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
3613
3614
3615
3616
3617
In Lamp file: For 4 cell, configure (cell1, cell2, cell3, cell4) MAXDLPOWER
(unit=0.1dBm)
as
(300,400,400,400)/(400,400,400,400)/(418,430,430,418)/(439,430,439,430)
respectively.
3618
1. Setup the cell and make a R99 call on cell1. Check result 1.
3619
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 170/174
3621
3622
3623
3624
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
3625
3626
3627
3628
3629
3630
4.2.5
3631
3632
3633
3634
3635
3636
3637
Test Label: 143 SETUP/DELETE ONE CELL ON 21C RRH WITH GEWEI PA VENDOR
Purpose:
Checking setup/delete one cell with different power on 21C RRH with Gewei PA Vendor.
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
Lamp and omcb connection
3638
3639
3640
3641
Procedure:
Configure cell parameter as below:
3642
3643
3644
3645
In
Lamp
file:
configure
MAXDLPOWER
(unit=0.1dBm)
as
300(1W)/369(5W)/400(10W)/417(15W)/430(20W)/444(28W)/447(30W)/454(35W)/460(
40W)/465(45W)/469(50W)/471(52W)/477(60W) respectively.
3646
1. Setup the cell and make a R99 call on this cell. Check result 1.
3647
3648
3649
3650
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
2. Cell is delete and no power output anymore.
3651
3652
3653
4.2.6
3654
3655
3656
3657
3658
Test Label: 144 SETUP/DELETE TWO CELLS ON 21C RRH WITH GEWEI PA VENDOR
Purpose:
Checking setup/delete two cells with different power on 21C RRH with Gewei PA vendor.
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 171/174
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
Lamp and omcb connection
3661
3662
3663
Procedure:
Configure cell parameter as below:
3664
3665
3666
In Lamp file: For 2 cell, configure (cell1, cell2) MAXDLPOWER (unit=0.1dBm) as (300,
400)/(400, 400)/(417, 430)/(430, 430)/(447, 447) respectively.
3667
3668
3669
3670
3671
3672
3673
3674
3675
Check result 1.
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
3676
3677
3678
3679
3680
3681
3682
3683
3684
3685
3686
3687
3688
3689
4.2.7
Test Label: 145 SETUP/DELETE THREE CELLS ON 21C RRH WITH GEWEI PA VENDOR
Purpose:
Checking setup/delete three cells with different power on 21C RRH with Gewei PA vendor.
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
Lamp and omcb connection
Procedure:
Configure cell parameter as below:
3690
3691
3692
In Lamp file: For 3 cell, configure (cell1, cell2, cell3) MAXDLPOWER (unit=0.1dBm) as
(300, 400, 400)/(400,400,400)/(417, 430, 430)/(430, 430,430) respectively.
3693
1. Setup the cell and make a R99 call on cell1. Check result 1.
3694
3695
3696
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 172/174
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
3700
3701
3702
3703
3704
4.2.8
3705
3706
3707
3708
3709
3710
3711
3712
Test Label: 146 SETUP/DELETE THREE CELLS ON 21C RRH WITH GEWEI PA VENDOR
3713
3714
3715
Procedure:
Purpose:
Checking setup/delete four cells with different power on 21C RRH with Gewei PA vendor.
Requirement:
Platform: 2UV2/3 rack + x/eCCM-U + x/eCEM-U
3716
3717
3718
3719
3720
In Lamp file: For 4 cell, configure (cell1, cell2, cell3, cell4) MAXDLPOWER
(unit=0.1dBm)
as
(300,400,400,400)/(400,400,400,400)/(418,430,430,418)/(439,430,439,430)
respectively.
3721
1. Setup the cell and make a R99 call on cell1. Check result 1.
3722
3723
3724
3725
3726
3727
Result:
1. Cell is setup successfully and the call is normal. Check output power through PSA, it
is the same value as configured above.
3728
3729
3730
3731
3732
3733
3734
Passing on or copying of this document, use and communication of its contents not permitted without AlcatelLucent written authorization
UMT/BTS/DJD/044741
V01.01/EN
Standard
04/12/2014
Page 173/174
3735
3736
6. ABBREVIATIONS
3737
ATM
3738
AWS
3739
BTS
3740
CCM
3741
CEM
3742
CPRI
3743
CTCH
3744
DCH
Dedicated Channel
3745
FACH
3746
GUI
3747
HSDPA
3748
HSUPA
3749
NBAP
3750
NodeB
3751
OAM
3752
OMC-B
3753
PCH
Paging Channel
3754
PCM
3755
RF
Radio Frequency
3756
RNC
3757
RRH
3758
SHO
Soft Handover
3759
SrHO
Softer Handover
3760
STSR
3761
TIL
3762
TRDU
END OF DOCUMENT
3763
UMT/BTS/DJD/044741
01.01/EN
Preliminary
30/Nov/2013
Page 174/174