Documente Academic
Documente Profesional
Documente Cultură
Functional Description
Meets NEMA TS1 & TS2 Environmental requirements:
temperature, shock, and vibration for traffic control
equipment.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic
Standard Immunity for industrial environment.
Supports IEEE802.3at Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex,
Auto-Negotiation, Auto-MDI/MDIX.
Supports 4096 MAC addresses. Provides 2.25M bits
buffer memory.
Alarms for power failure by relay output.
Power Supplies: Redundant 47-57VDC Terminal Block
power inputs.
Operating voltage and Max. current consumption: 9A @
55VDC. Power consumption: 495W Max.
-40 to 75 (-40 to 167) operating temperature
range. Tested for functional operation @ -40 to 85
(-40 to 185).
Supports Rack Mounting installation.
Physical Description
The Port Status LEDs and Power Inputs
LED
State
Power1
Power2
Steady
Power on.
Off
Power off.
Fault
Indication
Steady
Off
10/100Base-TX
Steady
A valid network connection established.
Link/ACT
Transmitting or receiving data.
Flashing
ACT stands for ACTIVITY.
10/100
PoE
Steady
Off
Steady
Off
LED
State
Indication
Gigabit Ethernet
Steady
A valid network connection established.
Link/ACT
Transmitting or receiving data.
Flashing
ACT stands for ACTIVITY.
TX
SFP
Steady
Off
Steady
Off
47-57VDC
Power2
Power Ground
47-57VDC
Power1
Power Ground
Terminal Block
Earth Ground
Relay Output Rating
1A @ 24VDC
Signal Name
TD
Signal Definition
Output Transmit Data
TD
RD
PoE
Positive (VCC+)
PoE
Positive (VCC+)
RD
PoE
Negative (VCC-)
PoE
Negative (VCC-)
Pin
1
Signal Name
TP0
Signal Definition
Transmit and Receive Data 0
TP0
TP1
TP2
TP2
TP1
TP3
TP3
Preface
A member of the growing family of rugged switches, this
Hardened PoE Ethernet Switch provides an affordable
solution for rugged and outdoor environment,
transportation road-side cabinet, industrial floor shop,
multitenant dwellings or Fiber To The Home (FTTH)
applications. Capable of operating at temperature
extremes of -40 to +75, this is the switch of choice for
harsh environments.
Port 1 to port 16 on this Switch supports IEEE802.3at
Power over Ethernet (PoE) Power Sourcing Equipment
(PSE) and can detect an IEEE802.3at compliant Powered
Device (PD). Using external 47~57VDC power inputs
through Terminal Block, data and power can be transmitted
to a Powered Device (PD) over the same twisted-pair
Ethernet cable through port 1 to port 16 on the Switch.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
Table of Contents
QUICK START GUIDE
FUNCTIONAL DESCRIPTION
PHYSICAL DESCRIPTION
1
2
2
3
PREFACE
TABLE OF CONTENTS
PRODUCT OVERVIEW
8
8
9
9
10
11
INSTALLATION
12
12
13
13
13
14
14
15
SPECIFICATIONS
16
Product Overview
Hardened PoE Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3
This Switch
Users Manual
Product Highlights
Basic Features
Meets NEMA TS1 & TS2 Environmental requirements:
temperature, shock, and vibration for traffic control
equipment.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic
Standard Immunity for industrial environment.
Supports IEEE802.3at Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex,
Auto-Negotiation, Auto-MDI/MDIX.
Supports 4096 MAC addresses. Provides 2.25M bits
buffer memory.
Alarms for power failure by relay output.
Power Supplies: Redundant 47-57VDC Terminal Block
power inputs.
Operating voltage and Max. current consumption: 9A @
55VDC. Power consumption: 495W Max.
-40 to 75 (-40 to 167) operating temperature
range. Tested for functional operation @ -40 to 85
(-40 to 185).
Supports Rack Mounting installation.
Status LEDs
LED
State
Power1
Power2
Steady
Power on.
Off
Power off.
Steady
Off
Fault
Indication
10/100Base-TX
Steady
A valid network connection established.
Link/ACT
Transmitting or receiving data.
Flashing
ACT stands for ACTIVITY.
10/100
PoE
Steady
Off
Steady
Off
10
LED
State
Indication
Gigabit Ethernet
Steady
A valid network connection established.
Link/ACT
Transmitting or receiving data.
Flashing
ACT stands for ACTIVITY.
TX
SFP
Steady
Off
Steady
Off
Physical Ports
This switch series provides different combinations of RJ-45
copper and fiber ports as below:
16 x 10/100Base-TX PoE ports + 2 x Gigabit Ethernet
ports
12 x 10/100Base-TX PoE ports + 2 x Gigabit Ethernet
ports
8 x 10/100Base-TX PoE ports + 2 x Gigabit Ethernet ports
CONNECTIVITY
RJ-45 connectors
SC or ST connector on 1000Base-SX/LX fiber port.
SC connector on 1000Base-BX fiber port.
SFP socket connection on 1000Base-SX/LX/BX fiber port.
11
Installation
This chapter gives step-by-step instructions about how to
install the switch:
12
Connecting to Power
Redundant DC Terminal Block Power Inputs:
47-57VDC
Power2
Power Ground
47-57VDC
Power1
Power Ground
Terminal Block
Earth Ground
Relay Output Rating
1A @ 24VDC
13
Port Speed
Half/Full
Duplex
Cable
Max.
Distance
4-pair UTP/STP
Cat. 3, 4, 5
4-pair UTP/STP
Cat. 5
4-pair UTP/STP
Cat. 5
MMF
(50
or
62.5m)
MMF
(50
or
62.5m)
SMF (9 or 10m)
SMF (9 or 10m)
100 m
10Base-T
RJ-45
10/20 Mbps
100Base-TX
RJ-45
100/200 Mbps
1000Base-T
RJ-45
2000 Mbps
1000Base-SX
SC, ST
2000 Mbps
1000Base-SX
SC
2000 Mbps
1000Base-LX
1000Base-BX
SFP
1000Base-SX
SC
SC
2000 Mbps
2000 Mbps
Duplex LC
2000 Mbps
1000Base-LX
Duplex LC
2000 Mbps
1000Base-BX
Single LC
2000 Mbps
1000Base-BX
Single LC
2000 Mbps
14
MMF
(50
62.5m)
SMF (9m)
or
MMF
(50
62.5m)
SMF (9m)
or
100 m
100 m
275, 550 m
2 km
10, 20 km
20 km
275 m, 550
m, 2 km
10, 20, 40,
70 km
550 m
10, 20 km
Cabling
Step 1:
<Note>
First, ensure the power of the switch and end devices are turned off.
Always ensure that the power is off before any installation.
Step 2:
Step 3:
Step 4:
Connect one end of the cable to the switch and the other end to a
desired device.
Step 5:
15
Specifications
Hardened PoE
Ethernet Switch
Applicable
Standards
Switching Method
Forwarding Rate
10Base-T:
100Base-TX:
1000Base-T/SX/LX:
Performance
Cable
10Base-T:
100Base-TX:
1000Base-T:
100Base-FX/BX:
1000Base-SX/LX/BX:
LED Indicators
Dimensions
Net Weight
Power
Operating Voltage &
Max. Current
Consumption
Power Consumption
Operating
Temperature
Storage Temperature
Humidity
RJ-45
EMI
FCC Part 15, Class A
16
17