Documente Academic
Documente Profesional
Documente Cultură
2.
3.
1.
4.
Begin by folding a Bird Fold the flap facing you all the
Base from a 20 to 25cm way up again, crease well, and
square, preferably coloured unfold. Repeat once more at
on both sides. the back.
Fold the flap facing you all
the way up, crease well,
and unfold. Repeat at the
back.
5.
6.
Now fold up the tip of the
uppermost flap to meet the
circled intersection as
shown. Crease firmly and
unfold, then turn the model
over and repeat this step at
the back.
8. 9.
10.
12.
11.
Swivel the flap on the ... then fold down the Swivel two layers on the left to the
right to the left ... triangular piece at the right, then repeat Steps 13 and 14
top. on the left. That done, swivel one
layer on the right to the left ...
17.
16.
18.
Lift up the horizonral edge in the middle and Make a mountain fold along the existing
reverse fold on the left and right along vertical crease line while lifting and swivelling
existing crease lines ... the pocket to the left ...
... like this. Repeat Step 20 Now sink fold along the ... like this. Repeat Step 22
on the right. Next, open existing crease lines as on the right ...
out the left half of the illustrated ...
model by grasping the
circled area and
pulling to the right.
24.
25. 26.
... then fold down the flap at Turn model over and repeat Valley fold a little of the left
the top. Steps 16 to 24 on the other edge down precisely as
side illustrated ...
27. 28. 29.
... then the right, bringing Valley fold on the left again, ... then on the right once more,
the edge to the like this .. in the precise proportions
intersecting vertical and illustrated.
horizontal lines.
Turn the model over ... ... and repeat Steps 26 to Your model should now
29, but in the opposite look like this, a mirror
direction, beginning image of Diagram 30.
from the right edge. Fold the flap up again.
This is a somewhat difficult. Valley ... until your model looks Fold down the flap at the
fold at the top, aligning with the like this. Repeat top again, ...
diagonal edge of the layer Step 33 on the
underneath, while making another right.
valley fold along the length of the
lower piece ...
36. 37.
38.
... turn the model over, and Note that the narrower
repeat from Step 32 on coloured layer in the middle
the other side. of the model is now to the ... then fold this piece at
right. Swivel one flap on the the lower half of the
right to the left ... model all the way up.
43.
45.
46. 47.
Do a rabbit's ear fold as illustrated. Follow Now mountain fold behind as shown.
the angles of the diagonal fold lines closely.
48. 49.
The next step is not clearly shown as it Reverse fold the head and tail pieces at
involves folds within the body. There should the precise angles illustrated.
be four right-angled tabs just above the legs.
Mountain fold each of these over the base of
the legs to lock the legs in place.
50. 51.
Fold down the white overlapping layer on ... then separate the two halves at the bottom
both sides of the head and tail pieces ... temporarily before doing an outside
reverse fold at the tail, and sinking the
corner at the base of the neck.
52.
53.
54.
55.
56.
59. 60.
... then mountain fold the ... like this. Reverse fold
second layer to the back again as illustrated.
while bringing the top of
this piece down ...
Valley fold precisely as Reverse fold the tip neatly ... then do an outside reverse
illustrated, crease firmly, in between the two layers fold along the crease lines
and unfold. immediately above, slightly made in Step 61 ...
less than midway from the
crease made in Step 61...
64. 65.
66.
67.
68.